[v2,05/13] phy: ti-pipe3: Add SATA DPLL support

USB and SATA DPLLs need different settings. Provide
the SATA DPLL settings and use the proper DPLL settings
based on device tree node's compatible_id.

Update the DT binding information.

Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 Documentation/devicetree/bindings/phy/ti-phy.txt |  3 +-
 drivers/phy/phy-ti-pipe3.c                       | 76 +++++++++++++++++-------
 2 files changed, 57 insertions(+), 22 deletions(-)

On Thursday 06 March 2014 08:08 PM, Roger Quadros wrote:
> USB and SATA DPLLs need different settings. Provide
> the SATA DPLL settings and use the proper DPLL settings
> based on device tree node's compatible_id.
>
> Update the DT binding information.
>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>   Documentation/devicetree/bindings/phy/ti-phy.txt |  3 +-
>   drivers/phy/phy-ti-pipe3.c                       | 76 +++++++++++++++++-------

same here..

-Kishon
>   2 files changed, 57 insertions(+), 22 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt
> index 8d13349..2c2d66a 100644
> --- a/Documentation/devicetree/bindings/phy/ti-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt
> @@ -53,7 +53,8 @@ usb2phy@4a0ad080 {
>   TI PIPE3 PHY
>
>   Required properties:
> - - compatible: Should be "ti,phy-usb3". "ti,omap-usb3" is deprecated.
> + - compatible: Should be "ti,phy-usb3" or "ti,phy-pipe3-sata".
> +   "ti,omap-usb3" is deprecated.
>    - reg : Address and length of the register set for the device.
>    - reg-names: The names of the register addresses corresponding to the registers
>      filled in "reg".
> diff --git a/drivers/phy/phy-ti-pipe3.c b/drivers/phy/phy-ti-pipe3.c
> index 211703c..f141237 100644
> --- a/drivers/phy/phy-ti-pipe3.c
> +++ b/drivers/phy/phy-ti-pipe3.c
> @@ -66,6 +66,11 @@ struct pipe3_dpll_params {
>   	u32	mf;
>   };
>
> +struct pipe3_dpll_map {
> +	unsigned long rate;
> +	struct pipe3_dpll_params params;
> +};
> +
>   struct ti_pipe3 {
>   	void __iomem		*pll_ctrl_base;
>   	struct device		*dev;
> @@ -73,20 +78,27 @@ struct ti_pipe3 {
>   	struct clk		*wkupclk;
>   	struct clk		*sys_clk;
>   	struct clk		*refclk;
> +	struct pipe3_dpll_map	*dpll_map;
>   };
>
> -struct pipe3_dpll_map {
> -	unsigned long rate;
> -	struct pipe3_dpll_params params;
> -};
> -
> -static struct pipe3_dpll_map dpll_map[] = {
> +static struct pipe3_dpll_map dpll_map_usb[] = {
>   	{12000000, {1250, 5, 4, 20, 0} },	/* 12 MHz */
>   	{16800000, {3125, 20, 4, 20, 0} },	/* 16.8 MHz */
>   	{19200000, {1172, 8, 4, 20, 65537} },	/* 19.2 MHz */
>   	{20000000, {1000, 7, 4, 10, 0} },	/* 20 MHz */
>   	{26000000, {1250, 12, 4, 20, 0} },	/* 26 MHz */
>   	{38400000, {3125, 47, 4, 20, 92843} },	/* 38.4 MHz */
> +	{ },					/* Terminator */
> +};
> +
> +static struct pipe3_dpll_map dpll_map_sata[] = {
> +	{12000000, {1000, 7, 4, 6, 0} },	/* 12 MHz */
> +	{16800000, {714, 7, 4, 6, 0} },		/* 16.8 MHz */
> +	{19200000, {625, 7, 4, 6, 0} },		/* 19.2 MHz */
> +	{20000000, {600, 7, 4, 6, 0} },		/* 20 MHz */
> +	{26000000, {461, 7, 4, 6, 0} },		/* 26 MHz */
> +	{38400000, {312, 7, 4, 6, 0} },		/* 38.4 MHz */
> +	{ },					/* Terminator */
>   };
>
>   static inline u32 ti_pipe3_readl(void __iomem *addr, unsigned offset)
> @@ -100,15 +112,20 @@ static inline void ti_pipe3_writel(void __iomem *addr, unsigned offset,
>   	__raw_writel(data, addr + offset);
>   }
>
> -static struct pipe3_dpll_params *ti_pipe3_get_dpll_params(unsigned long rate)
> +static struct pipe3_dpll_params *ti_pipe3_get_dpll_params(struct ti_pipe3 *phy)
>   {
> -	int i;
> +	unsigned long rate;
> +	struct pipe3_dpll_map *dpll_map = phy->dpll_map;
>
> -	for (i = 0; i < ARRAY_SIZE(dpll_map); i++) {
> -		if (rate == dpll_map[i].rate)
> -			return &dpll_map[i].params;
> +	rate = clk_get_rate(phy->sys_clk);
> +
> +	for (; dpll_map->rate; dpll_map++) {
> +		if (rate == dpll_map->rate)
> +			return &dpll_map->params;
>   	}
>
> +	dev_err(phy->dev, "No DPLL configuration for %lu Hz SYS CLK\n", rate);
> +
>   	return NULL;
>   }
>
> @@ -182,16 +199,11 @@ static void ti_pipe3_dpll_relock(struct ti_pipe3 *phy)
>   static int ti_pipe3_dpll_lock(struct ti_pipe3 *phy)
>   {
>   	u32			val;
> -	unsigned long		rate;
>   	struct pipe3_dpll_params *dpll_params;
>
> -	rate = clk_get_rate(phy->sys_clk);
> -	dpll_params = ti_pipe3_get_dpll_params(rate);
> -	if (!dpll_params) {
> -		dev_err(phy->dev,
> -			  "No DPLL configuration for %lu Hz SYS CLK\n", rate);
> +	dpll_params = ti_pipe3_get_dpll_params(phy);
> +	if (!dpll_params)
>   		return -EINVAL;
> -	}
>
>   	val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
>   	val &= ~PLL_REGN_MASK;
> @@ -244,6 +256,10 @@ static struct phy_ops ops = {
>   	.owner		= THIS_MODULE,
>   };
>
> +#ifdef CONFIG_OF
> +static const struct of_device_id ti_pipe3_id_table[];
> +#endif
> +
>   static int ti_pipe3_probe(struct platform_device *pdev)
>   {
>   	struct ti_pipe3 *phy;
> @@ -253,8 +269,10 @@ static int ti_pipe3_probe(struct platform_device *pdev)
>   	struct device_node *node = pdev->dev.of_node;
>   	struct device_node *control_node;
>   	struct platform_device *control_pdev;
> +	const struct of_device_id *match;
>
> -	if (!node)
> +	match = of_match_device(of_match_ptr(ti_pipe3_id_table), &pdev->dev);
> +	if (!match)
>   		return -EINVAL;
>
>   	phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
> @@ -263,6 +281,12 @@ static int ti_pipe3_probe(struct platform_device *pdev)
>   		return -ENOMEM;
>   	}
>
> +	phy->dpll_map = (struct pipe3_dpll_map *)match->data;
> +	if (!phy->dpll_map) {
> +		dev_err(&pdev->dev, "no DPLL data\n");
> +		return -EINVAL;
> +	}
> +
>   	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pll_ctrl");
>   	phy->pll_ctrl_base = devm_ioremap_resource(&pdev->dev, res);
>   	if (IS_ERR(phy->pll_ctrl_base))
> @@ -388,8 +412,18 @@ static const struct dev_pm_ops ti_pipe3_pm_ops = {
>
>   #ifdef CONFIG_OF
>   static const struct of_device_id ti_pipe3_id_table[] = {
> -	{ .compatible = "ti,phy-usb3" },
> -	{ .compatible = "ti,omap-usb3" },
> +	{
> +		.compatible = "ti,phy-usb3",
> +		.data = dpll_map_usb,
> +	},
> +	{
> +		.compatible = "ti,omap-usb3",
> +		.data = dpll_map_usb,
> +	},
> +	{
> +		.compatible = "ti,phy-pipe3-sata",
> +		.data = dpll_map_sata,
> +	},
>   	{}
>   };
>   MODULE_DEVICE_TABLE(of, ti_pipe3_id_table);
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/