| Message ID | 20201031181242.742301-11-jic23@kernel.org |
|---|---|
| State | New |
| Headers | show |
| Series | dt-bindings: iio: conversion of consumer drivers | expand |
On Sat, Oct 31, 2020 at 11:15 AM Jonathan Cameron <jic23@kernel.org> wrote: > > From: Jonathan Cameron <Jonathan.Cameron@huawei.com> > > There were a few parts of the example that did not conform to the > binding description and would not have worked with the Linux driver > as a result. Fixed them whilst doing this conversion. > > Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> > Cc: Matt Ranostay <matt.ranostay@konsulko.com> Acked-by: Matt Ranostay <matt.ranostay@konsulko.com> > --- > .../bindings/iio/potentiostat/lmp91000.txt | 33 --------- > .../iio/potentiostat/ti,lmp91000.yaml | 68 +++++++++++++++++++ > 2 files changed, 68 insertions(+), 33 deletions(-) > > diff --git a/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt b/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt > deleted file mode 100644 > index f3ab02b0dd41..000000000000 > --- a/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt > +++ /dev/null > @@ -1,33 +0,0 @@ > -* Texas Instruments LMP91000 series of potentiostats > - > -LMP91000: https://www.ti.com/lit/ds/symlink/lmp91000.pdf > -LMP91002: https://www.ti.com/lit/ds/symlink/lmp91002.pdf > - > -Required properties: > - > - - compatible: should be one of the following: > - "ti,lmp91000" > - "ti,lmp91002" > - - reg: the I2C address of the device > - - io-channels: the phandle of the iio provider > - > - - ti,external-tia-resistor: if the property ti,tia-gain-ohm is not defined this > - needs to be set to signal that an external resistor value is being used. > - > -Optional properties: > - > - - ti,tia-gain-ohm: ohm value of the internal resistor for the transimpedance > - amplifier. Must be 2750, 3500, 7000, 14000, 35000, 120000, or 350000 ohms. > - > - - ti,rload-ohm: ohm value of the internal resistor load applied to the gas > - sensor. Must be 10, 33, 50, or 100 (default) ohms. > - > -Example: > - > -lmp91000@48 { > - compatible = "ti,lmp91000"; > - reg = <0x48>; > - ti,tia-gain-ohm = <7500>; > - ti,rload = <100>; > - io-channels = <&adc>; > -}; > diff --git a/Documentation/devicetree/bindings/iio/potentiostat/ti,lmp91000.yaml b/Documentation/devicetree/bindings/iio/potentiostat/ti,lmp91000.yaml > new file mode 100644 > index 000000000000..e4b5d890e8d5 > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/potentiostat/ti,lmp91000.yaml > @@ -0,0 +1,68 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/iio/potentiostat/ti,lmp91000.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Texas Instruments LMP91000 series of potentiostats with I2C control > + > +maintainers: > + - Matt Ranostay <matt.ranostay@konsulko.com> > + > +description: | > + Typically used as a signal conditioner for chemical sensors. > + LMP91000: https://www.ti.com/lit/ds/symlink/lmp91000.pdf > + LMP91002: https://www.ti.com/lit/ds/symlink/lmp91002.pdf > + > +properties: > + compatible: > + enum: > + - ti,lmp91000 > + - ti,lmp91002 > + > + reg: > + maxItems: 1 > + > + io-channels: > + maxItems: 1 > + > + ti,external-tia-resistor: > + $ref: /schemas/types.yaml#/definitions/flag > + description: > + If the property ti,tia-gain-ohm is not defined this needs to be set to > + signal that an external resistor value is being used. > + > + ti,tia-gain-ohm: > + $ref: /schemas/types.yaml#/definitions/uint32 > + enum: [2750, 3500, 7000, 14000, 35000, 120000, 350000] > + description: > + Internal resistor for the transimpedance amplifier. > + > + ti,rload-ohm: > + $ref: /schemas/types.yaml#/definitions/uint32 > + enum: [10, 33, 50, 100] > + description: > + Internal resistor load applied to the gas sensor. > + Default 100 Ohms. > + > +required: > + - compatible > + - reg > + - io-channels > + > +additionalProperties: false > + > +examples: > + - | > + i2c { > + #address-cells = <1>; > + #size-cells = <0>; > + lmp91000@48 { > + compatible = "ti,lmp91000"; > + reg = <0x48>; > + ti,tia-gain-ohm = <7000>; > + ti,rload-ohm = <100>; > + io-channels = <&adc>; > + }; > + }; > +... > -- > 2.28.0 >
On Sat, 31 Oct 2020 14:41:10 -0700 Matt Ranostay <matt.ranostay@konsulko.com> wrote: > On Sat, Oct 31, 2020 at 11:15 AM Jonathan Cameron <jic23@kernel.org> wrote: > > > > From: Jonathan Cameron <Jonathan.Cameron@huawei.com> > > > > There were a few parts of the example that did not conform to the > > binding description and would not have worked with the Linux driver > > as a result. Fixed them whilst doing this conversion. > > > > Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> > > Cc: Matt Ranostay <matt.ranostay@konsulko.com> > > Acked-by: Matt Ranostay <matt.ranostay@konsulko.com> Note I couldn't drop the type markings for the resistance properties here because the dt-schema uses ohms and these are ohm. An unfortunate bit of legacy we'll need to maintain I guess. Jonathan > > > --- > > .../bindings/iio/potentiostat/lmp91000.txt | 33 --------- > > .../iio/potentiostat/ti,lmp91000.yaml | 68 +++++++++++++++++++ > > 2 files changed, 68 insertions(+), 33 deletions(-) > > > > diff --git a/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt b/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt > > deleted file mode 100644 > > index f3ab02b0dd41..000000000000 > > --- a/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt > > +++ /dev/null > > @@ -1,33 +0,0 @@ > > -* Texas Instruments LMP91000 series of potentiostats > > - > > -LMP91000: https://www.ti.com/lit/ds/symlink/lmp91000.pdf > > -LMP91002: https://www.ti.com/lit/ds/symlink/lmp91002.pdf > > - > > -Required properties: > > - > > - - compatible: should be one of the following: > > - "ti,lmp91000" > > - "ti,lmp91002" > > - - reg: the I2C address of the device > > - - io-channels: the phandle of the iio provider > > - > > - - ti,external-tia-resistor: if the property ti,tia-gain-ohm is not defined this > > - needs to be set to signal that an external resistor value is being used. > > - > > -Optional properties: > > - > > - - ti,tia-gain-ohm: ohm value of the internal resistor for the transimpedance > > - amplifier. Must be 2750, 3500, 7000, 14000, 35000, 120000, or 350000 ohms. > > - > > - - ti,rload-ohm: ohm value of the internal resistor load applied to the gas > > - sensor. Must be 10, 33, 50, or 100 (default) ohms. > > - > > -Example: > > - > > -lmp91000@48 { > > - compatible = "ti,lmp91000"; > > - reg = <0x48>; > > - ti,tia-gain-ohm = <7500>; > > - ti,rload = <100>; > > - io-channels = <&adc>; > > -}; > > diff --git a/Documentation/devicetree/bindings/iio/potentiostat/ti,lmp91000.yaml b/Documentation/devicetree/bindings/iio/potentiostat/ti,lmp91000.yaml > > new file mode 100644 > > index 000000000000..e4b5d890e8d5 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/iio/potentiostat/ti,lmp91000.yaml > > @@ -0,0 +1,68 @@ > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/iio/potentiostat/ti,lmp91000.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Texas Instruments LMP91000 series of potentiostats with I2C control > > + > > +maintainers: > > + - Matt Ranostay <matt.ranostay@konsulko.com> > > + > > +description: | > > + Typically used as a signal conditioner for chemical sensors. > > + LMP91000: https://www.ti.com/lit/ds/symlink/lmp91000.pdf > > + LMP91002: https://www.ti.com/lit/ds/symlink/lmp91002.pdf > > + > > +properties: > > + compatible: > > + enum: > > + - ti,lmp91000 > > + - ti,lmp91002 > > + > > + reg: > > + maxItems: 1 > > + > > + io-channels: > > + maxItems: 1 > > + > > + ti,external-tia-resistor: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: > > + If the property ti,tia-gain-ohm is not defined this needs to be set to > > + signal that an external resistor value is being used. > > + > > + ti,tia-gain-ohm: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + enum: [2750, 3500, 7000, 14000, 35000, 120000, 350000] > > + description: > > + Internal resistor for the transimpedance amplifier. > > + > > + ti,rload-ohm: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + enum: [10, 33, 50, 100] > > + description: > > + Internal resistor load applied to the gas sensor. > > + Default 100 Ohms. > > + > > +required: > > + - compatible > > + - reg > > + - io-channels > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + i2c { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + lmp91000@48 { > > + compatible = "ti,lmp91000"; > > + reg = <0x48>; > > + ti,tia-gain-ohm = <7000>; > > + ti,rload-ohm = <100>; > > + io-channels = <&adc>; > > + }; > > + }; > > +... > > -- > > 2.28.0 > >
diff --git a/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt b/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt deleted file mode 100644 index f3ab02b0dd41..000000000000 --- a/Documentation/devicetree/bindings/iio/potentiostat/lmp91000.txt +++ /dev/null @@ -1,33 +0,0 @@ -* Texas Instruments LMP91000 series of potentiostats - -LMP91000: https://www.ti.com/lit/ds/symlink/lmp91000.pdf -LMP91002: https://www.ti.com/lit/ds/symlink/lmp91002.pdf - -Required properties: - - - compatible: should be one of the following: - "ti,lmp91000" - "ti,lmp91002" - - reg: the I2C address of the device - - io-channels: the phandle of the iio provider - - - ti,external-tia-resistor: if the property ti,tia-gain-ohm is not defined this - needs to be set to signal that an external resistor value is being used. - -Optional properties: - - - ti,tia-gain-ohm: ohm value of the internal resistor for the transimpedance - amplifier. Must be 2750, 3500, 7000, 14000, 35000, 120000, or 350000 ohms. - - - ti,rload-ohm: ohm value of the internal resistor load applied to the gas - sensor. Must be 10, 33, 50, or 100 (default) ohms. - -Example: - -lmp91000@48 { - compatible = "ti,lmp91000"; - reg = <0x48>; - ti,tia-gain-ohm = <7500>; - ti,rload = <100>; - io-channels = <&adc>; -}; diff --git a/Documentation/devicetree/bindings/iio/potentiostat/ti,lmp91000.yaml b/Documentation/devicetree/bindings/iio/potentiostat/ti,lmp91000.yaml new file mode 100644 index 000000000000..e4b5d890e8d5 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/potentiostat/ti,lmp91000.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/potentiostat/ti,lmp91000.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments LMP91000 series of potentiostats with I2C control + +maintainers: + - Matt Ranostay <matt.ranostay@konsulko.com> + +description: | + Typically used as a signal conditioner for chemical sensors. + LMP91000: https://www.ti.com/lit/ds/symlink/lmp91000.pdf + LMP91002: https://www.ti.com/lit/ds/symlink/lmp91002.pdf + +properties: + compatible: + enum: + - ti,lmp91000 + - ti,lmp91002 + + reg: + maxItems: 1 + + io-channels: + maxItems: 1 + + ti,external-tia-resistor: + $ref: /schemas/types.yaml#/definitions/flag + description: + If the property ti,tia-gain-ohm is not defined this needs to be set to + signal that an external resistor value is being used. + + ti,tia-gain-ohm: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [2750, 3500, 7000, 14000, 35000, 120000, 350000] + description: + Internal resistor for the transimpedance amplifier. + + ti,rload-ohm: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [10, 33, 50, 100] + description: + Internal resistor load applied to the gas sensor. + Default 100 Ohms. + +required: + - compatible + - reg + - io-channels + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + lmp91000@48 { + compatible = "ti,lmp91000"; + reg = <0x48>; + ti,tia-gain-ohm = <7000>; + ti,rload-ohm = <100>; + io-channels = <&adc>; + }; + }; +...