| Message ID | 20201204054347.2877857-4-vkoul@kernel.org |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add binding and dts for Qualcomm SM8350 | expand |
On Fri, Dec 04, 2020 at 11:13:46AM +0530, Vinod Koul wrote: > Add basic devicetree support for Qualcomm Technologies, Inc SM8350 SoC. > This adds gcc, pinctrl, reserved memory, uart, cpu nodes for this SoC. > > Signed-off-by: Vinod Koul <vkoul@kernel.org> > --- > arch/arm64/boot/dts/qcom/sm8350.dtsi | 496 +++++++++++++++++++++++++++ > 1 file changed, 496 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/sm8350.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi > new file mode 100644 > index 000000000000..9e4bb29abe62 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi > @@ -0,0 +1,496 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2020, Linaro Limaited > + */ > + > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/clock/qcom,gcc-sm8350.h> > +#include <dt-bindings/clock/qcom,rpmh.h> > +#include <dt-bindings/mailbox/qcom-ipcc.h> > +#include <dt-bindings/power/qcom-aoss-qmp.h> > +#include <dt-bindings/power/qcom-rpmpd.h> > +#include <dt-bindings/soc/qcom,rpmh-rsc.h> > + > +/ { > + interrupt-parent = <&intc>; > + > + #address-cells = <2>; > + #size-cells = <2>; > + > + chosen { }; > + > + clocks { > + xo_board: xo-board { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <38400000>; > + clock-output-names = "xo_board"; > + }; > + > + sleep_clk: sleep-clk { > + compatible = "fixed-clock"; > + clock-frequency = <32000>; > + #clock-cells = <0>; > + }; > + }; > + > + cpus { > + #address-cells = <2>; > + #size-cells = <0>; > + > + CPU0: cpu@0 { > + device_type = "cpu"; > + compatible = "qcom,kryo"; Not documented. Nor likely specific enough to be accepted. > + reg = <0x0 0x0>; > + enable-method = "psci"; > + next-level-cache = <&L2_0>; > + L2_0: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; Should have a 'level' property IIRC. > + L3_0: l3-cache { Seems like this should be outside of cpus. > + compatible = "cache"; > + }; > + }; > + }; > + > + CPU1: cpu@100 { > + device_type = "cpu"; > + compatible = "qcom,kryo"; > + reg = <0x0 0x100>; > + enable-method = "psci"; > + next-level-cache = <&L2_100>; > + L2_100: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU2: cpu@200 { > + device_type = "cpu"; > + compatible = "qcom,kryo"; > + reg = <0x0 0x200>; > + enable-method = "psci"; > + next-level-cache = <&L2_200>; > + L2_200: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU3: cpu@300 { > + device_type = "cpu"; > + compatible = "qcom,kryo"; > + reg = <0x0 0x300>; > + enable-method = "psci"; > + next-level-cache = <&L2_300>; > + L2_300: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU4: cpu@400 { > + device_type = "cpu"; > + compatible = "qcom,kryo485"; > + reg = <0x0 0x400>; > + enable-method = "psci"; > + next-level-cache = <&L2_400>; > + L2_400: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU5: cpu@500 { > + device_type = "cpu"; > + compatible = "qcom,kryo485"; > + reg = <0x0 0x500>; > + enable-method = "psci"; > + next-level-cache = <&L2_500>; > + L2_500: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + > + }; > + > + CPU6: cpu@600 { > + device_type = "cpu"; > + compatible = "qcom,kryo485"; > + reg = <0x0 0x600>; > + enable-method = "psci"; > + next-level-cache = <&L2_600>; > + L2_600: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + > + CPU7: cpu@700 { > + device_type = "cpu"; > + compatible = "qcom,kryo485"; > + reg = <0x0 0x700>; > + enable-method = "psci"; > + next-level-cache = <&L2_700>; > + L2_700: l2-cache { > + compatible = "cache"; > + next-level-cache = <&L3_0>; > + }; > + }; > + }; > + > + firmware { > + scm: scm { > + compatible = "qcom,scm"; SoC specific compatible? > + #reset-cells = <1>; > + }; > + }; > + > + memory@80000000 { > + device_type = "memory"; > + /* We expect the bootloader to fill in the size */ > + reg = <0x0 0x80000000 0x0 0x0>; > + }; > + > + pmu { > + compatible = "arm,armv8-pmuv3"; > + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; > + }; Non-homogeneous system (big.LITTLE?), but only 1 PMU? All cores have the same events? > + > + psci { > + compatible = "arm,psci-1.0"; > + method = "smc"; > + }; > + > + reserved_memory: reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + hyp_mem: memory@80000000 { > + reg = <0x0 0x80000000 0x0 0x600000>; > + no-map; > + }; > + > + xbl_aop_mem: memory@80700000 { > + no-map; > + reg = <0x0 0x80700000 0x0 0x160000>; > + }; > + > + cmd_db: memory@80860000 { > + compatible = "qcom,cmd-db"; > + reg = <0x0 0x80860000 0x0 0x20000>; > + no-map; > + }; > + > + reserved_xbl_uefi_log: memory@80880000 { > + reg = <0x0 0x80880000 0x0 0x14000>; > + no-map; > + }; > + > + smem_mem: memory@80900000 { > + reg = <0x0 0x80900000 0x0 0x200000>; > + no-map; > + }; > + > + cpucp_fw_mem: memory@80b00000 { > + reg = <0x0 0x80b00000 0x0 0x100000>; > + no-map; > + }; > + > + cdsp_secure_heap: memory@80c00000 { > + reg = <0x0 0x80c00000 0x0 0x4600000>; > + no-map; > + }; > + > + pil_camera_mem: mmeory@85200000 { > + reg = <0x0 0x85200000 0x0 0x500000>; > + no-map; > + }; > + > + pil_video_mem: memory@85700000 { > + reg = <0x0 0x85700000 0x0 0x500000>; > + no-map; > + }; > + > + pil_cvp_mem: memory@85c00000 { > + reg = <0x0 0x85c00000 0x0 0x500000>; > + no-map; > + }; > + > + pil_adsp_mem: memory@86100000 { > + reg = <0x0 0x86100000 0x0 0x2100000>; > + no-map; > + }; > + > + pil_slpi_mem: memory@88200000 { > + reg = <0x0 0x88200000 0x0 0x1500000>; > + no-map; > + }; > + > + pil_cdsp_mem: memory@89700000 { > + reg = <0x0 0x89700000 0x0 0x1e00000>; > + no-map; > + }; > + > + pil_ipa_fw_mem: memory@8b500000 { > + reg = <0x0 0x8b500000 0x0 0x10000>; > + no-map; > + }; > + > + pil_ipa_gsi_mem: memory@8b510000 { > + reg = <0x0 0x8b510000 0x0 0xa000>; > + no-map; > + }; > + > + pil_gpu_mem: memory@8b51a000 { > + reg = <0x0 0x8b51a000 0x0 0x2000>; > + no-map; > + }; > + > + pil_spss_mem: memory@8b600000 { > + reg = <0x0 0x8b600000 0x0 0x100000>; > + no-map; > + }; > + > + pil_modem_mem: memory@8b800000 { > + reg = <0x0 0x8b800000 0x0 0x10000000>; > + no-map; > + }; > + > + hyp_reserved_mem: memory@d0000000 { > + reg = <0x0 0xd0000000 0x0 0x800000>; > + no-map; > + }; > + > + pil_trustedvm_mem: memory@d0800000 { > + reg = <0x0 0xd0800000 0x0 0x76f7000>; > + no-map; > + }; > + > + qrtr_shbuf: memory@d7ef7000 { > + reg = <0x0 0xd7ef7000 0x0 0x9000>; > + no-map; > + }; > + > + chan0_shbuf: memory@d7f00000 { > + reg = <0x0 0xd7f00000 0x0 0x80000>; > + no-map; > + }; > + > + chan1_shbuf: memory@d7f80000 { > + reg = <0x0 0xd7f80000 0x0 0x80000>; > + no-map; > + }; > + > + removed_mem: memory@d8800000 { > + reg = <0x0 0xd8800000 0x0 0x6800000>; > + no-map; > + }; > + }; > + > + smem: qcom,smem { > + compatible = "qcom,smem"; > + memory-region = <&smem_mem>; > + hwlocks = <&tcsr_mutex 3>; > + }; > + > + soc: soc@0 { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges = <0 0 0 0 0x10 0>; > + dma-ranges = <0 0 0 0 0x10 0>; > + compatible = "simple-bus"; > + > + gcc: clock-controller@100000 { > + compatible = "qcom,gcc-sm8350"; > + reg = <0x0 0x00100000 0x0 0x1f0000>; > + #clock-cells = <1>; > + #reset-cells = <1>; > + #power-domain-cells = <1>; > + clock-names = "bi_tcxo", "sleep_clk"; > + clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>; > + }; > + > + ipcc: mailbox@408000 { > + compatible = "qcom,sm8350-ipcc", "qcom,ipcc"; > + reg = <0 0x00408000 0 0x1000>; > + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <3>; > + #mbox-cells = <2>; > + }; > + > + qupv3_id_1: geniqup@9c0000 { > + compatible = "qcom,geni-se-qup"; > + reg = <0x0 0x009c0000 0x0 0x6000>; > + clock-names = "m-ahb", "s-ahb"; > + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>, > + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + status = "disabled"; > + > + uart2: serial@98c000 { > + compatible = "qcom,geni-debug-uart"; > + reg = <0 0x0098c000 0 0x4000>; > + clock-names = "se"; > + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; > + pinctrl-names = "default"; > + pinctrl-0 = <&qup_uart3_default>; > + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + }; > + > + tcsr_mutex: hwlock@1f40000 { > + compatible = "qcom,tcsr-mutex"; > + reg = <0x0 0x01f40000 0x0 0x40000>; > + #hwlock-cells = <1>; > + }; > + > + pdc: interrupt-controller@b220000 { > + compatible = "qcom,sm8350-pdc", "qcom,pdc"; > + reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>; > + qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>, <55 306 4>, > + <59 312 3>, <62 374 2>, <64 434 2>, <66 438 3>, > + <69 86 1>, <70 520 54>, <124 609 31>, <155 63 1>, > + <156 716 12>; > + #interrupt-cells = <2>; > + interrupt-parent = <&intc>; > + interrupt-controller; > + }; > + > + aoss_qmp: qmp@c300000 { > + compatible = "qcom,sm8350-aoss-qmp"; > + reg = <0 0x0c300000 0 0x100000>; > + interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP > + IRQ_TYPE_EDGE_RISING>; > + mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>; > + > + #clock-cells = <0>; > + #power-domain-cells = <1>; > + }; > + > + tlmm: pinctrl@f000000 { > + compatible = "qcom,sm8350-pinctrl"; > + reg = <0 0x0f100000 0 0x300000>; > + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + gpio-ranges = <&tlmm 0 0 203>; > + > + qup_uart3_default: qup-uart3-default { > + mux { > + pins = "gpio18", "gpio19"; > + function = "qup3"; > + }; > + }; > + }; > + > + intc: interrupt-controller@17a00000 { > + compatible = "arm,gic-v3"; > + #interrupt-cells = <3>; > + interrupt-controller; > + reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */ > + <0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */ > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + timer@17c20000 { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + compatible = "arm,armv7-timer-mem"; > + reg = <0x0 0x17c20000 0x0 0x1000>; > + clock-frequency = <19200000>; > + > + frame@17c21000 { > + frame-number = <0>; > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c21000 0x0 0x1000>, > + <0x0 0x17c22000 0x0 0x1000>; > + }; > + > + frame@17c23000 { > + frame-number = <1>; > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c23000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c25000 { > + frame-number = <2>; > + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c25000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c27000 { > + frame-number = <3>; > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c27000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c29000 { > + frame-number = <4>; > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c29000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c2b000 { > + frame-number = <5>; > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c2b000 0x0 0x1000>; > + status = "disabled"; > + }; > + > + frame@17c2d000 { > + frame-number = <6>; > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0 0x17c2d000 0x0 0x1000>; > + status = "disabled"; > + }; > + }; > + > + apps_rsc: rsc@18200000 { > + label = "apps_rsc"; > + compatible = "qcom,rpmh-rsc"; > + reg = <0x0 0x18200000 0x0 0x10000>, > + <0x0 0x18210000 0x0 0x10000>, > + <0x0 0x18220000 0x0 0x10000>; > + reg-names = "drv-0", "drv-1", "drv-2"; > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; > + qcom,tcs-offset = <0xd00>; > + qcom,drv-id = <2>; > + qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>, > + <WAKE_TCS 3>, <CONTROL_TCS 1>; > + > + rpmhcc: clock-controller { > + compatible = "qcom,sm8350-rpmh-clk"; > + #clock-cells = <1>; > + clock-names = "xo"; > + clocks = <&xo_board>; > + }; > + > + }; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; > + }; > +}; > -- > 2.26.2 >
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi new file mode 100644 index 000000000000..9e4bb29abe62 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi @@ -0,0 +1,496 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Linaro Limaited + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/qcom,gcc-sm8350.h> +#include <dt-bindings/clock/qcom,rpmh.h> +#include <dt-bindings/mailbox/qcom-ipcc.h> +#include <dt-bindings/power/qcom-aoss-qmp.h> +#include <dt-bindings/power/qcom-rpmpd.h> +#include <dt-bindings/soc/qcom,rpmh-rsc.h> + +/ { + interrupt-parent = <&intc>; + + #address-cells = <2>; + #size-cells = <2>; + + chosen { }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + clock-output-names = "xo_board"; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32000>; + #clock-cells = <0>; + }; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + L3_0: l3-cache { + compatible = "cache"; + }; + }; + }; + + CPU1: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x100>; + enable-method = "psci"; + next-level-cache = <&L2_100>; + L2_100: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU2: cpu@200 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x200>; + enable-method = "psci"; + next-level-cache = <&L2_200>; + L2_200: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU3: cpu@300 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x300>; + enable-method = "psci"; + next-level-cache = <&L2_300>; + L2_300: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU4: cpu@400 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x400>; + enable-method = "psci"; + next-level-cache = <&L2_400>; + L2_400: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU5: cpu@500 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x500>; + enable-method = "psci"; + next-level-cache = <&L2_500>; + L2_500: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + + }; + + CPU6: cpu@600 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x600>; + enable-method = "psci"; + next-level-cache = <&L2_600>; + L2_600: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU7: cpu@700 { + device_type = "cpu"; + compatible = "qcom,kryo485"; + reg = <0x0 0x700>; + enable-method = "psci"; + next-level-cache = <&L2_700>; + L2_700: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + }; + + firmware { + scm: scm { + compatible = "qcom,scm"; + #reset-cells = <1>; + }; + }; + + memory@80000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0x0 0x80000000 0x0 0x0>; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved_memory: reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + hyp_mem: memory@80000000 { + reg = <0x0 0x80000000 0x0 0x600000>; + no-map; + }; + + xbl_aop_mem: memory@80700000 { + no-map; + reg = <0x0 0x80700000 0x0 0x160000>; + }; + + cmd_db: memory@80860000 { + compatible = "qcom,cmd-db"; + reg = <0x0 0x80860000 0x0 0x20000>; + no-map; + }; + + reserved_xbl_uefi_log: memory@80880000 { + reg = <0x0 0x80880000 0x0 0x14000>; + no-map; + }; + + smem_mem: memory@80900000 { + reg = <0x0 0x80900000 0x0 0x200000>; + no-map; + }; + + cpucp_fw_mem: memory@80b00000 { + reg = <0x0 0x80b00000 0x0 0x100000>; + no-map; + }; + + cdsp_secure_heap: memory@80c00000 { + reg = <0x0 0x80c00000 0x0 0x4600000>; + no-map; + }; + + pil_camera_mem: mmeory@85200000 { + reg = <0x0 0x85200000 0x0 0x500000>; + no-map; + }; + + pil_video_mem: memory@85700000 { + reg = <0x0 0x85700000 0x0 0x500000>; + no-map; + }; + + pil_cvp_mem: memory@85c00000 { + reg = <0x0 0x85c00000 0x0 0x500000>; + no-map; + }; + + pil_adsp_mem: memory@86100000 { + reg = <0x0 0x86100000 0x0 0x2100000>; + no-map; + }; + + pil_slpi_mem: memory@88200000 { + reg = <0x0 0x88200000 0x0 0x1500000>; + no-map; + }; + + pil_cdsp_mem: memory@89700000 { + reg = <0x0 0x89700000 0x0 0x1e00000>; + no-map; + }; + + pil_ipa_fw_mem: memory@8b500000 { + reg = <0x0 0x8b500000 0x0 0x10000>; + no-map; + }; + + pil_ipa_gsi_mem: memory@8b510000 { + reg = <0x0 0x8b510000 0x0 0xa000>; + no-map; + }; + + pil_gpu_mem: memory@8b51a000 { + reg = <0x0 0x8b51a000 0x0 0x2000>; + no-map; + }; + + pil_spss_mem: memory@8b600000 { + reg = <0x0 0x8b600000 0x0 0x100000>; + no-map; + }; + + pil_modem_mem: memory@8b800000 { + reg = <0x0 0x8b800000 0x0 0x10000000>; + no-map; + }; + + hyp_reserved_mem: memory@d0000000 { + reg = <0x0 0xd0000000 0x0 0x800000>; + no-map; + }; + + pil_trustedvm_mem: memory@d0800000 { + reg = <0x0 0xd0800000 0x0 0x76f7000>; + no-map; + }; + + qrtr_shbuf: memory@d7ef7000 { + reg = <0x0 0xd7ef7000 0x0 0x9000>; + no-map; + }; + + chan0_shbuf: memory@d7f00000 { + reg = <0x0 0xd7f00000 0x0 0x80000>; + no-map; + }; + + chan1_shbuf: memory@d7f80000 { + reg = <0x0 0xd7f80000 0x0 0x80000>; + no-map; + }; + + removed_mem: memory@d8800000 { + reg = <0x0 0xd8800000 0x0 0x6800000>; + no-map; + }; + }; + + smem: qcom,smem { + compatible = "qcom,smem"; + memory-region = <&smem_mem>; + hwlocks = <&tcsr_mutex 3>; + }; + + soc: soc@0 { + #address-cells = <2>; + #size-cells = <2>; + ranges = <0 0 0 0 0x10 0>; + dma-ranges = <0 0 0 0 0x10 0>; + compatible = "simple-bus"; + + gcc: clock-controller@100000 { + compatible = "qcom,gcc-sm8350"; + reg = <0x0 0x00100000 0x0 0x1f0000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "bi_tcxo", "sleep_clk"; + clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>; + }; + + ipcc: mailbox@408000 { + compatible = "qcom,sm8350-ipcc", "qcom,ipcc"; + reg = <0 0x00408000 0 0x1000>; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <3>; + #mbox-cells = <2>; + }; + + qupv3_id_1: geniqup@9c0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x009c0000 0x0 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>, + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + uart2: serial@98c000 { + compatible = "qcom,geni-debug-uart"; + reg = <0 0x0098c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart3_default>; + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + }; + + tcsr_mutex: hwlock@1f40000 { + compatible = "qcom,tcsr-mutex"; + reg = <0x0 0x01f40000 0x0 0x40000>; + #hwlock-cells = <1>; + }; + + pdc: interrupt-controller@b220000 { + compatible = "qcom,sm8350-pdc", "qcom,pdc"; + reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>; + qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>, <55 306 4>, + <59 312 3>, <62 374 2>, <64 434 2>, <66 438 3>, + <69 86 1>, <70 520 54>, <124 609 31>, <155 63 1>, + <156 716 12>; + #interrupt-cells = <2>; + interrupt-parent = <&intc>; + interrupt-controller; + }; + + aoss_qmp: qmp@c300000 { + compatible = "qcom,sm8350-aoss-qmp"; + reg = <0 0x0c300000 0 0x100000>; + interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>; + + #clock-cells = <0>; + #power-domain-cells = <1>; + }; + + tlmm: pinctrl@f000000 { + compatible = "qcom,sm8350-pinctrl"; + reg = <0 0x0f100000 0 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 203>; + + qup_uart3_default: qup-uart3-default { + mux { + pins = "gpio18", "gpio19"; + function = "qup3"; + }; + }; + }; + + intc: interrupt-controller@17a00000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */ + <0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer@17c20000 { + #address-cells = <2>; + #size-cells = <2>; + ranges; + compatible = "arm,armv7-timer-mem"; + reg = <0x0 0x17c20000 0x0 0x1000>; + clock-frequency = <19200000>; + + frame@17c21000 { + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c21000 0x0 0x1000>, + <0x0 0x17c22000 0x0 0x1000>; + }; + + frame@17c23000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c23000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c25000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c25000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c27000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c27000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c29000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c29000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c2b000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c2b000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c2d000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17c2d000 0x0 0x1000>; + status = "disabled"; + }; + }; + + apps_rsc: rsc@18200000 { + label = "apps_rsc"; + compatible = "qcom,rpmh-rsc"; + reg = <0x0 0x18200000 0x0 0x10000>, + <0x0 0x18210000 0x0 0x10000>, + <0x0 0x18220000 0x0 0x10000>; + reg-names = "drv-0", "drv-1", "drv-2"; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + qcom,tcs-offset = <0xd00>; + qcom,drv-id = <2>; + qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>, + <WAKE_TCS 3>, <CONTROL_TCS 1>; + + rpmhcc: clock-controller { + compatible = "qcom,sm8350-rpmh-clk"; + #clock-cells = <1>; + clock-names = "xo"; + clocks = <&xo_board>; + }; + + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; + }; +};
Add basic devicetree support for Qualcomm Technologies, Inc SM8350 SoC. This adds gcc, pinctrl, reserved memory, uart, cpu nodes for this SoC. Signed-off-by: Vinod Koul <vkoul@kernel.org> --- arch/arm64/boot/dts/qcom/sm8350.dtsi | 496 +++++++++++++++++++++++++++ 1 file changed, 496 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8350.dtsi -- 2.26.2