diff mbox series

[v2,10/10] arm64: dts: qcom: sa8155p-adp: Add base dts file

Message ID 20210615074543.26700-11-bhupesh.sharma@linaro.org
State Superseded
Headers show
Series arm64: dts: qcom: Add SA8155p-adp board DTS | expand

Commit Message

Bhupesh Sharma June 15, 2021, 7:45 a.m. UTC 
Add base DTS file for SA8155p Automotive Development Platform.
It enables boot to console, adds tlmm reserved range and ufs flash.
It also includes pmic file.

SA8155p-adp board is based on sa8155p Qualcomm Snapdragon SoC.
SA8155p platform is similar to the SM8150, so use this as base
for now.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
---
 arch/arm64/boot/dts/qcom/Makefile        |   1 +
 arch/arm64/boot/dts/qcom/sa8155p-adp.dts | 355 +++++++++++++++++++++++
 2 files changed, 356 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sa8155p-adp.dts

Comments

Konrad Dybcio June 15, 2021, 2:53 p.m. UTC | #1 
Hi,


> +
> +	reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
> +
> +	vcc-supply = <&vreg_l10a_2p96>;
> +	vcc-max-microamp = <750000>;
> +	vccq-supply = <&vreg_l5c_1p2>;
> +	vccq-max-microamp = <700000>;
> +	vccq2-supply = <&vreg_s4a_1p8>;
> +	vccq2-max-microamp = <750000>;

You need to add "regulator-allow-set-load;" to the mentioned supplies,

as you're controlling the amperage here.


> +};
> +
> +&ufs_mem_phy {
> +	status = "okay";
> +
> +	vdda-phy-supply = <&vreg_l8c_1p2>;
> +	vdda-max-microamp = <87100>;
> +	vdda-pll-supply = <&vreg_l5a_0p88>;
> +	vdda-pll-max-microamp = <18300>;

Ditto


Konrad
Bjorn Andersson June 15, 2021, 9:13 p.m. UTC | #2 
On Tue 15 Jun 02:45 CDT 2021, Bhupesh Sharma wrote:

> Add base DTS file for SA8155p Automotive Development Platform.
> It enables boot to console, adds tlmm reserved range and ufs flash.
> It also includes pmic file.
> 
> SA8155p-adp board is based on sa8155p Qualcomm Snapdragon SoC.
> SA8155p platform is similar to the SM8150, so use this as base
> for now.
> 
> Cc: Linus Walleij <linus.walleij@linaro.org>
> Cc: Liam Girdwood <lgirdwood@gmail.com>
> Cc: Mark Brown <broonie@kernel.org>
> Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
> Cc: Vinod Koul <vkoul@kernel.org>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Andy Gross <agross@kernel.org>

With the feedback of regulator-allow-set-load addressed this looks good!

Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Regards,
Bjorn

> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/Makefile        |   1 +
>  arch/arm64/boot/dts/qcom/sa8155p-adp.dts | 355 +++++++++++++++++++++++
>  2 files changed, 356 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/sa8155p-adp.dts
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 456502aeee49..666f3528697d 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -32,6 +32,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-oneplus-dumpling.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qrb5165-rb5.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= sa8155p-adp.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1-lte.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
> new file mode 100644
> index 000000000000..95e0a6612e6b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
> @@ -0,0 +1,355 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2021, Linaro Limited
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include "sm8150.dtsi"
> +#include "pmm8155au_1.dtsi"
> +#include "pmm8155au_2.dtsi"
> +
> +/ {
> +	model = "Qualcomm Technologies, Inc. SA8155P ADP";
> +	compatible = "qcom,sa8155p-adp", "qcom,sa8155p";
> +
> +	aliases {
> +		serial0 = &uart2;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	vreg_3p3: vreg_3p3_regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vreg_3p3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	/*
> +	 * S4A is always on and not controllable through RPMh.
> +	 * So model it as a fixed regulator.
> +	 */
> +	vreg_s4a_1p8: smps4 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vreg_s4a_1p8";
> +
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +
> +		regulator-always-on;
> +		regulator-boot-on;
> +
> +		vin-supply = <&vreg_3p3>;
> +	};
> +};
> +
> +&apps_rsc {
> +	pmm8155au-1-rpmh-regulators {
> +		compatible = "qcom,pmm8155au-rpmh-regulators";
> +		qcom,pmic-id = "a";
> +
> +		vdd-s1-supply = <&vreg_3p3>;
> +		vdd-s2-supply = <&vreg_3p3>;
> +		vdd-s3-supply = <&vreg_3p3>;
> +		vdd-s4-supply = <&vreg_3p3>;
> +		vdd-s5-supply = <&vreg_3p3>;
> +		vdd-s6-supply = <&vreg_3p3>;
> +		vdd-s7-supply = <&vreg_3p3>;
> +		vdd-s8-supply = <&vreg_3p3>;
> +		vdd-s9-supply = <&vreg_3p3>;
> +		vdd-s10-supply = <&vreg_3p3>;
> +
> +		vdd-l1-l8-l11-supply = <&vreg_s6a_0p92>;
> +		vdd-l2-l10-supply = <&vreg_3p3>;
> +		vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p92>;
> +		vdd-l6-l9-supply = <&vreg_s6a_0p92>;
> +		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
> +		vdd-l13-l16-l17-supply = <&vreg_3p3>;
> +
> +		vreg_s5a_2p04: smps5 {
> +			regulator-name = "vreg_s5a_2p04";
> +			regulator-min-microvolt = <1904000>;
> +			regulator-max-microvolt = <2000000>;
> +		};
> +
> +		vreg_s6a_0p92: smps6 {
> +			regulator-name = "vreg_s6a_0p92";
> +			regulator-min-microvolt = <920000>;
> +			regulator-max-microvolt = <1128000>;
> +		};
> +
> +		vreg_l1a_0p752: ldo1 {
> +			regulator-name = "vreg_l1a_0p752";
> +			regulator-min-microvolt = <752000>;
> +			regulator-max-microvolt = <752000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vdda_usb_hs_3p1:
> +		vreg_l2a_3p072: ldo2 {
> +			regulator-name = "vreg_l2a_3p072";
> +			regulator-min-microvolt = <3072000>;
> +			regulator-max-microvolt = <3072000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l3a_0p8: ldo3 {
> +			regulator-name = "vreg_l3a_0p8";
> +			regulator-min-microvolt = <800000>;
> +			regulator-max-microvolt = <800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vdd_usb_hs_core:
> +		vdda_usb_ss_dp_core_1:
> +		vreg_l5a_0p88: ldo5 {
> +			regulator-name = "vreg_l5a_0p88";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <880000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l7a_1p8: ldo7 {
> +			regulator-name = "vreg_l7a_1p8";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l10a_2p96: ldo10 {
> +			regulator-name = "vreg_l10a_2p96";
> +			regulator-min-microvolt = <2504000>;
> +			regulator-max-microvolt = <2960000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l11a_0p8: ldo11 {
> +			regulator-name = "vreg_l11a_0p8";
> +			regulator-min-microvolt = <800000>;
> +			regulator-max-microvolt = <800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vdda_usb_hs_1p8:
> +		vreg_l12a_1p8: ldo12 {
> +			regulator-name = "vreg_l12a_1p8";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l13a_2p7: ldo13 {
> +			regulator-name = "vreg_l13a_2p7";
> +			regulator-min-microvolt = <2704000>;
> +			regulator-max-microvolt = <2704000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l15a_1p7: ldo15 {
> +			regulator-name = "vreg_l15a_1p7";
> +			regulator-min-microvolt = <1704000>;
> +			regulator-max-microvolt = <1704000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l16a_2p7: ldo16 {
> +			regulator-name = "vreg_l16a_2p7";
> +			regulator-min-microvolt = <2704000>;
> +			regulator-max-microvolt = <2960000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l17a_2p96: ldo17 {
> +			regulator-name = "vreg_l17a_2p96";
> +			regulator-min-microvolt = <2504000>;
> +			regulator-max-microvolt = <2960000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	pmm8155au-2-rpmh-regulators {
> +		compatible = "qcom,pmm8155au-rpmh-regulators";
> +		qcom,pmic-id = "c";
> +
> +		vdd-s1-supply = <&vreg_3p3>;
> +		vdd-s2-supply = <&vreg_3p3>;
> +		vdd-s3-supply = <&vreg_3p3>;
> +		vdd-s4-supply = <&vreg_3p3>;
> +		vdd-s5-supply = <&vreg_3p3>;
> +		vdd-s6-supply = <&vreg_3p3>;
> +		vdd-s7-supply = <&vreg_3p3>;
> +		vdd-s8-supply = <&vreg_3p3>;
> +		vdd-s9-supply = <&vreg_3p3>;
> +		vdd-s10-supply = <&vreg_3p3>;
> +
> +		vdd-l1-l8-l11-supply = <&vreg_s4c_1p352>;
> +		vdd-l2-l10-supply = <&vreg_3p3>;
> +		vdd-l3-l4-l5-l18-supply = <&vreg_s4c_1p352>;
> +		vdd-l6-l9-supply = <&vreg_s6c_1p128>;
> +		vdd-l7-l12-l14-l15-supply = <&vreg_s5c_2p04>;
> +		vdd-l13-l16-l17-supply = <&vreg_3p3>;
> +
> +		vreg_s4c_1p352: smps4 {
> +			regulator-name = "vreg_s4c_1p352";
> +			regulator-min-microvolt = <1352000>;
> +			regulator-max-microvolt = <1352000>;
> +		};
> +
> +		vreg_s5c_2p04: smps5 {
> +			regulator-name = "vreg_s5c_2p04";
> +			regulator-min-microvolt = <1904000>;
> +			regulator-max-microvolt = <2000000>;
> +		};
> +
> +		vreg_s6c_1p128: smps6 {
> +			regulator-name = "vreg_s6c_1p128";
> +			regulator-min-microvolt = <1128000>;
> +			regulator-max-microvolt = <1128000>;
> +		};
> +
> +		vreg_l1c_1p304: ldo1 {
> +			regulator-name = "vreg_l1c_1p304";
> +			regulator-min-microvolt = <1304000>;
> +			regulator-max-microvolt = <1304000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l2c_1p808: ldo2 {
> +			regulator-name = "vreg_l2c_1p808";
> +			regulator-min-microvolt = <1704000>;
> +			regulator-max-microvolt = <2928000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l5c_1p2: ldo5 {
> +			regulator-name = "vreg_l5c_1p2";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l7c_1p8: ldo7 {
> +			regulator-name = "vreg_l7c_1p8";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l8c_1p2: ldo8 {
> +			regulator-name = "vreg_l8c_1p2";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l10c_3p3: ldo10 {
> +			regulator-name = "vreg_l10c_3p3";
> +			regulator-min-microvolt = <3000000>;
> +			regulator-max-microvolt = <3312000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l11c_0p8: ldo11 {
> +			regulator-name = "vreg_l11c_0p8";
> +			regulator-min-microvolt = <800000>;
> +			regulator-max-microvolt = <800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l12c_1p808: ldo12 {
> +			regulator-name = "vreg_l12c_1p808";
> +			regulator-min-microvolt = <1704000>;
> +			regulator-max-microvolt = <2928000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l13c_2p96: ldo13 {
> +			regulator-name = "vreg_l13c_2p96";
> +			regulator-min-microvolt = <2504000>;
> +			regulator-max-microvolt = <2960000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l15c_1p9: ldo15 {
> +			regulator-name = "vreg_l15c_1p9";
> +			regulator-min-microvolt = <1704000>;
> +			regulator-max-microvolt = <2928000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l16c_3p008: ldo16 {
> +			regulator-name = "vreg_l16c_3p008";
> +			regulator-min-microvolt = <3008000>;
> +			regulator-max-microvolt = <3008000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l18c_0p88: ldo18 {
> +			regulator-name = "vreg_l18c_0p88";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <880000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +};
> +
> +&tlmm {
> +	gpio-reserved-ranges = <0 4>;
> +};
> +
> +&uart2 {
> +	status = "okay";
> +};
> +
> +&ufs_mem_hc {
> +	status = "okay";
> +
> +	reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
> +
> +	vcc-supply = <&vreg_l10a_2p96>;
> +	vcc-max-microamp = <750000>;
> +	vccq-supply = <&vreg_l5c_1p2>;
> +	vccq-max-microamp = <700000>;
> +	vccq2-supply = <&vreg_s4a_1p8>;
> +	vccq2-max-microamp = <750000>;
> +};
> +
> +&ufs_mem_phy {
> +	status = "okay";
> +
> +	vdda-phy-supply = <&vreg_l8c_1p2>;
> +	vdda-max-microamp = <87100>;
> +	vdda-pll-supply = <&vreg_l5a_0p88>;
> +	vdda-pll-max-microamp = <18300>;
> +};
> +
> +
> +&usb_1_hsphy {
> +	status = "okay";
> +	vdda-pll-supply = <&vdd_usb_hs_core>;
> +	vdda33-supply = <&vdda_usb_hs_3p1>;
> +	vdda18-supply = <&vdda_usb_hs_1p8>;
> +};
> +
> +&usb_1_qmpphy {
> +	status = "okay";
> +	vdda-phy-supply = <&vreg_l8c_1p2>;
> +	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
> +};
> +
> +&usb_1 {
> +	status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> +	dr_mode = "peripheral";
> +};
> +
> +&qupv3_id_1 {
> +	status = "okay";
> +};
> -- 
> 2.31.1
>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 456502aeee49..666f3528697d 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -32,6 +32,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-oneplus-dumpling.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qrb5165-rb5.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sa8155p-adp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1-lte.dtb
diff --git a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
new file mode 100644
index 000000000000..95e0a6612e6b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
@@ -0,0 +1,355 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "sm8150.dtsi"
+#include "pmm8155au_1.dtsi"
+#include "pmm8155au_2.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SA8155P ADP";
+	compatible = "qcom,sa8155p-adp", "qcom,sa8155p";
+
+	aliases {
+		serial0 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	vreg_3p3: vreg_3p3_regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	/*
+	 * S4A is always on and not controllable through RPMh.
+	 * So model it as a fixed regulator.
+	 */
+	vreg_s4a_1p8: smps4 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s4a_1p8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vreg_3p3>;
+	};
+};
+
+&apps_rsc {
+	pmm8155au-1-rpmh-regulators {
+		compatible = "qcom,pmm8155au-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vdd-s1-supply = <&vreg_3p3>;
+		vdd-s2-supply = <&vreg_3p3>;
+		vdd-s3-supply = <&vreg_3p3>;
+		vdd-s4-supply = <&vreg_3p3>;
+		vdd-s5-supply = <&vreg_3p3>;
+		vdd-s6-supply = <&vreg_3p3>;
+		vdd-s7-supply = <&vreg_3p3>;
+		vdd-s8-supply = <&vreg_3p3>;
+		vdd-s9-supply = <&vreg_3p3>;
+		vdd-s10-supply = <&vreg_3p3>;
+
+		vdd-l1-l8-l11-supply = <&vreg_s6a_0p92>;
+		vdd-l2-l10-supply = <&vreg_3p3>;
+		vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p92>;
+		vdd-l6-l9-supply = <&vreg_s6a_0p92>;
+		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
+		vdd-l13-l16-l17-supply = <&vreg_3p3>;
+
+		vreg_s5a_2p04: smps5 {
+			regulator-name = "vreg_s5a_2p04";
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2000000>;
+		};
+
+		vreg_s6a_0p92: smps6 {
+			regulator-name = "vreg_s6a_0p92";
+			regulator-min-microvolt = <920000>;
+			regulator-max-microvolt = <1128000>;
+		};
+
+		vreg_l1a_0p752: ldo1 {
+			regulator-name = "vreg_l1a_0p752";
+			regulator-min-microvolt = <752000>;
+			regulator-max-microvolt = <752000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_usb_hs_3p1:
+		vreg_l2a_3p072: ldo2 {
+			regulator-name = "vreg_l2a_3p072";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3a_0p8: ldo3 {
+			regulator-name = "vreg_l3a_0p8";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_usb_hs_core:
+		vdda_usb_ss_dp_core_1:
+		vreg_l5a_0p88: ldo5 {
+			regulator-name = "vreg_l5a_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a_1p8: ldo7 {
+			regulator-name = "vreg_l7a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10a_2p96: ldo10 {
+			regulator-name = "vreg_l10a_2p96";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11a_0p8: ldo11 {
+			regulator-name = "vreg_l11a_0p8";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_usb_hs_1p8:
+		vreg_l12a_1p8: ldo12 {
+			regulator-name = "vreg_l12a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a_2p7: ldo13 {
+			regulator-name = "vreg_l13a_2p7";
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15a_1p7: ldo15 {
+			regulator-name = "vreg_l15a_1p7";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1704000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16a_2p7: ldo16 {
+			regulator-name = "vreg_l16a_2p7";
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17a_2p96: ldo17 {
+			regulator-name = "vreg_l17a_2p96";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pmm8155au-2-rpmh-regulators {
+		compatible = "qcom,pmm8155au-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-s1-supply = <&vreg_3p3>;
+		vdd-s2-supply = <&vreg_3p3>;
+		vdd-s3-supply = <&vreg_3p3>;
+		vdd-s4-supply = <&vreg_3p3>;
+		vdd-s5-supply = <&vreg_3p3>;
+		vdd-s6-supply = <&vreg_3p3>;
+		vdd-s7-supply = <&vreg_3p3>;
+		vdd-s8-supply = <&vreg_3p3>;
+		vdd-s9-supply = <&vreg_3p3>;
+		vdd-s10-supply = <&vreg_3p3>;
+
+		vdd-l1-l8-l11-supply = <&vreg_s4c_1p352>;
+		vdd-l2-l10-supply = <&vreg_3p3>;
+		vdd-l3-l4-l5-l18-supply = <&vreg_s4c_1p352>;
+		vdd-l6-l9-supply = <&vreg_s6c_1p128>;
+		vdd-l7-l12-l14-l15-supply = <&vreg_s5c_2p04>;
+		vdd-l13-l16-l17-supply = <&vreg_3p3>;
+
+		vreg_s4c_1p352: smps4 {
+			regulator-name = "vreg_s4c_1p352";
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s5c_2p04: smps5 {
+			regulator-name = "vreg_s5c_2p04";
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2000000>;
+		};
+
+		vreg_s6c_1p128: smps6 {
+			regulator-name = "vreg_s6c_1p128";
+			regulator-min-microvolt = <1128000>;
+			regulator-max-microvolt = <1128000>;
+		};
+
+		vreg_l1c_1p304: ldo1 {
+			regulator-name = "vreg_l1c_1p304";
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_1p808: ldo2 {
+			regulator-name = "vreg_l2c_1p808";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5c_1p2: ldo5 {
+			regulator-name = "vreg_l5c_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c_1p8: ldo7 {
+			regulator-name = "vreg_l7c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8c_1p2: ldo8 {
+			regulator-name = "vreg_l8c_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10c_3p3: ldo10 {
+			regulator-name = "vreg_l10c_3p3";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11c_0p8: ldo11 {
+			regulator-name = "vreg_l11c_0p8";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12c_1p808: ldo12 {
+			regulator-name = "vreg_l12c_1p808";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13c_2p96: ldo13 {
+			regulator-name = "vreg_l13c_2p96";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15c_1p9: ldo15 {
+			regulator-name = "vreg_l15c_1p9";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16c_3p008: ldo16 {
+			regulator-name = "vreg_l16c_3p008";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l18c_0p88: ldo18 {
+			regulator-name = "vreg_l18c_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>;
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l10a_2p96>;
+	vcc-max-microamp = <750000>;
+	vccq-supply = <&vreg_l5c_1p2>;
+	vccq-max-microamp = <700000>;
+	vccq2-supply = <&vreg_s4a_1p8>;
+	vccq2-max-microamp = <750000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l8c_1p2>;
+	vdda-max-microamp = <87100>;
+	vdda-pll-supply = <&vreg_l5a_0p88>;
+	vdda-pll-max-microamp = <18300>;
+};
+
+
+&usb_1_hsphy {
+	status = "okay";
+	vdda-pll-supply = <&vdd_usb_hs_core>;
+	vdda33-supply = <&vdda_usb_hs_3p1>;
+	vdda18-supply = <&vdda_usb_hs_1p8>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+	vdda-phy-supply = <&vreg_l8c_1p2>;
+	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};