@@ -112,6 +112,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-villager-r1-lte.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-crd-r3.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sc8180x-primus.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-crd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-lenovo-thinkpad-x13s.dtb
dtb-$(CONFIG_ARCH_QCOM) += sda660-inforce-ifc6560.dtb
new file mode 100644
@@ -0,0 +1,326 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2021-2022, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+
+/ {
+ thermal-zones {
+ pmc8180-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pmc8180_temp>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+
+ trip2 {
+ temperature = <145000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
+ pmc8180c-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pmc8180c_temp>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+
+ trip2 {
+ temperature = <145000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
+&spmi_bus {
+ pmc8180_0: pmic@0 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pon: power-on@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x0800>;
+ pwrkey {
+ compatible = "qcom,pm8941-pwrkey";
+ interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_POWER>;
+
+ status = "disabled";
+ };
+ };
+
+ pmc8180_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+ io-channels = <&pmc8180_adc ADC5_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmc8180_adc: adc@3100 {
+ compatible = "qcom,spmi-adc5";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ die-temp@6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "die_temp";
+ };
+ };
+
+ pmc8180_adc_tm: adc-tm@3500 {
+ compatible = "qcom,spmi-adc-tm5";
+ reg = <0x3500>;
+ interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+ #thermal-sensor-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ rtc@6000 {
+ compatible = "qcom,pm8941-rtc";
+ reg = <0x6000>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+ };
+
+ pmc8180_gpios: gpio@c000 {
+ compatible = "qcom,pmc8180-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmic@1 {
+ compatible = "qcom,pmc8180", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pmic@2 {
+ compatible = "qcom,smb2351", "qcom,spmi-pmic";
+ reg = <0x2 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@3100 {
+ compatible = "qcom,spmi-adc-rev2";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ vcoin@85 {
+ reg = <0x85>;
+ qcom,pre-scaling = <1 1>;
+ label = "vcoin2";
+ };
+ };
+ };
+
+ pmic@6 {
+ compatible = "qcom,pm8150c", "qcom,spmi-pmic";
+ reg = <0x6 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pmic@8 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x8 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pmic@a {
+ compatible = "qcom,smb2351", "qcom,spmi-pmic";
+ reg = <0xa SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@3100 {
+ compatible = "qcom,spmi-adc-rev2";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0xa 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ vcoin@85 {
+ reg = <0x85>;
+ qcom,pre-scaling = <1 1>;
+ label = "vcoin";
+ };
+ };
+ };
+
+ pmic@4 {
+ compatible = "qcom,pm8150c", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ power-on@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x0800>;
+
+ status = "disabled";
+ };
+
+ pmc8180c_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+ io-channels = <&pmc8180c_adc ADC5_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmc8180c_adc: adc@3100 {
+ compatible = "qcom,spmi-adc5";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ die-temp@6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "die_temp";
+ };
+ };
+
+ pmc8180c_adc_tm: adc-tm@3500 {
+ compatible = "qcom,spmi-adc-tm5";
+ reg = <0x3500>;
+ interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+ #thermal-sensor-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ pmc8180c_gpios: gpio@c000 {
+ compatible = "qcom,pmc8180c-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmic@5 {
+ compatible = "qcom,pmc8180c", "qcom,spmi-pmic";
+ reg = <0x5 SPMI_USID>;
+
+ pmc8180c_lpg: lpg {
+ compatible = "qcom,pmc8180c-lpg";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #pwm-cells = <2>;
+
+ status = "disabled";
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,706 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020-2021, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sc8180x.dtsi"
+#include "sc8180x-pmics.dtsi"
+
+/ {
+ model = "Qualcomm SC8180x Primus";
+ compatible = "qcom,sc8180x-primus", "qcom,sc8180x";
+
+ aliases {
+ serial0 = &uart12;
+ serial1 = &uart13;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pmc8180c_lpg 4 1000000>;
+ enable-gpios = <&pmc8180c_gpios 8 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_pwm_default_state>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&hall_int_active_state>;
+
+ lid-switch {
+ gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ wakeup-source;
+ wakeup-event-action = <EV_ACT_DEASSERTED>;
+ };
+ };
+
+ reserved-memory {
+ rmtfs_mem: rmtfs-region@85500000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0x0 0x85500000 0x0 0x200000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ qcom,vmid = <15>;
+ };
+
+ wlan_mem: wlan-region@8bc00000 {
+ reg = <0x0 0x8bc00000 0x0 0x180000>;
+ no-map;
+ };
+
+ adsp_mem: adsp-region@96e00000 {
+ reg = <0x0 0x96e00000 0x0 0x1c00000>;
+ no-map;
+ };
+
+ mpss_mem: mpss-region@8d800000 {
+ reg = <0x0 0x8d800000 0x0 0x9600000>;
+ no-map;
+ };
+
+ gpu_mem: gpu-region@98a00000 {
+ reg = <0x0 0x98a00000 0x0 0x2000>;
+ no-map;
+ };
+
+ reserved-region@9a500000 {
+ reg = <0x0 0x9a500000 0x0 0x600000>;
+ no-map;
+ };
+ };
+
+ vreg_nvme_0p9: nvme-0p9-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_nvme_0p9";
+
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-always-on;
+ };
+
+ vreg_nvme_3p3: nvme-3p3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_nvme_3p3";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmc8180c_gpios 11 0>;
+ enable-active-high;
+
+ regulator-always-on;
+ };
+
+ vdd_kb_tp_3v3: vdd-kb-tp-3v3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_kb_tp_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ regulator-always-on;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&kb_tp_3v3_en_active_state>;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ vreg_s4a_1p8: pm8150-s4 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_s4a_1p8";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+
+ vin-supply = <&vph_pwr>;
+ };
+};
+
+&apps_rsc {
+ pmc8180-a-rpmh-regulators {
+ compatible = "qcom,pmc8180-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p0>;
+
+ vreg_s5a_2p0: smps5 {
+ regulator-min-microvolt = <2040000>;
+ regulator-max-microvolt = <2100000>;
+ };
+
+ vreg_l7a_1p8: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9a_1p3: ldo9 {
+ regulator-min-microvolt = <1296000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12a_1p8: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ pmc8180c-rpmh-regulators {
+ compatible = "qcom,pmc8180c-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-l2-l3-supply = <&vreg_s6c_1p35>;
+ vdd-bob-supply = <&vph_pwr>;
+
+ vreg_s6c_1p35: smps6 {
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1372000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s8c_1p8: smps8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l3c_1p2: ldo3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4c_3p3: ldo4 {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10c_3p3: ldo10 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11c_3p3: ldo11 {
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3350000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ pmc8180-e-rpmh-regulators {
+ compatible = "qcom,pmc8180-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-l2-l10-supply = <&vreg_bob>;
+ vdd-l3-l4-l5-l18-supply = <&vreg_s4e_0p98>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s5e_2p05>;
+ vdd-l13-l16-l17-supply = <&vreg_bob>;
+
+ vreg_s4e_0p98: smps4 {
+ regulator-min-microvolt = <992000>;
+ regulator-max-microvolt = <992000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5e_2p05: smps5 {
+ regulator-min-microvolt = <2040000>;
+ regulator-max-microvolt = <2040000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1e_0p75: ldo1 {
+ regulator-min-microvolt = <752000>;
+ regulator-max-microvolt = <752000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5e_0p88: ldo5 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7e_1p8: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10e_2p9: ldo10 {
+ regulator-min-microvolt = <2904000>;
+ regulator-max-microvolt = <2904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12e: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l16e_3p0: ldo16 {
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&dispcc {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+
+ zap-shader {
+ memory-region = <&gpu_mem>;
+ firmware-name = "qcom/sc8180x/qcdxkmsuc8180.mbn";
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_i2c_active_state>;
+
+ status = "okay";
+
+ touchscreen@10 {
+ compatible = "hid-over-i2c";
+ reg = <0x10>;
+ hid-descr-addr = <0x1>;
+
+ vdd-supply = <&vreg_l4c_3p3>;
+ vddl-supply = <&vreg_l12e>;
+
+ post-power-on-delay-ms = <20>;
+
+ interrupts-extended = <&tlmm 122 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_active_state>;
+ };
+};
+
+&i2c7 {
+ clock-frequency = <100000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&aux_i2c_active_state>;
+
+ status = "okay";
+
+ touchpad@15 {
+ compatible = "hid-over-i2c";
+ reg = <0x15>;
+ hid-descr-addr = <0x1>;
+
+ interrupts-extended = <&tlmm 24 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tp_int_active_state>;
+
+ vdd-supply = <&vdd_kb_tp_3v3>;
+ };
+
+ keyboard@3a {
+ compatible = "hid-over-i2c";
+ reg = <0x3a>;
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&kb_int_active_state>;
+
+ vdd-supply = <&vdd_kb_tp_3v3>;
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_edp {
+ data-lanes = <0 1 2 3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_hpd_active>;
+
+ status = "okay";
+
+ aux-bus {
+ panel {
+ compatible = "edp-panel";
+
+ backlight = <&backlight>;
+
+ ports {
+ port {
+ auo_b133han05_in: endpoint {
+ remote-endpoint = <&mdss_edp_out>;
+ };
+ };
+ };
+ };
+ };
+
+ ports {
+ port@1 {
+ reg = <1>;
+ mdss_edp_out: endpoint {
+ remote-endpoint = <&auo_b133han05_in>;
+ };
+ };
+ };
+};
+
+&pcie1 {
+ perst-gpio = <&tlmm 175 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 177 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie2_default_state>;
+
+ status = "okay";
+};
+
+&pcie1_phy {
+ vdda-phy-supply = <&vreg_l5e_0p88>;
+ vdda-pll-supply = <&vreg_l3c_1p2>;
+
+ status = "okay";
+};
+
+&pmc8180c_lpg {
+ status = "okay";
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&qupv3_id_2 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ memory-region = <&adsp_mem>;
+ firmware-name = "qcom/sc8180x/qcadsp8180.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_mpss {
+ memory-region = <&mpss_mem>;
+ firmware-name = "qcom/sc8180x/qcmpss8180.mbn";
+
+ status = "okay";
+};
+
+&uart12 {
+ compatible = "qcom,geni-debug-uart";
+ status = "okay";
+};
+
+&uart13 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart13_state>;
+
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3998-bt";
+
+ vddio-supply = <&vreg_s4a_1p8>;
+ vddxo-supply = <&vreg_l7a_1p8>;
+ vddrf-supply = <&vreg_l9a_1p3>;
+ vddch0-supply = <&vreg_l11c_3p3>;
+ max-speed = <3200000>;
+ };
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 190 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l10e_2p9>;
+ vcc-max-microamp = <155000>;
+
+ vccq2-supply = <&vreg_l7e_1p8>;
+ vccq2-max-microamp = <425000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l5e_0p88>;
+ vdda-pll-supply = <&vreg_l3c_1p2>;
+
+ status = "okay";
+};
+
+&usb_prim_hsphy {
+ vdda-pll-supply = <&vreg_l5e_0p88>;
+ vdda18-supply = <&vreg_l12a_1p8>;
+ vdda33-supply = <&vreg_l16e_3p0>;
+
+ status = "okay";
+};
+
+&usb_prim_qmpphy {
+ vdda-phy-supply = <&vreg_l3c_1p2>;
+ vdda-pll-supply = <&vreg_l5e_0p88>;
+
+ status = "okay";
+};
+
+&usb_prim {
+ status = "okay";
+};
+
+&usb_prim_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_sec_hsphy {
+ vdda-pll-supply = <&vreg_l5e_0p88>;
+ vdda18-supply = <&vreg_l12a_1p8>;
+ vdda33-supply = <&vreg_l16e_3p0>;
+
+ status = "okay";
+};
+
+&usb_sec_qmpphy {
+ vdda-phy-supply = <&vreg_l3c_1p2>;
+ vdda-pll-supply = <&vreg_l5e_0p88>;
+
+ status = "okay";
+};
+
+&usb_sec {
+ status = "okay";
+};
+
+&usb_sec_dwc3 {
+ dr_mode = "host";
+};
+
+&wifi {
+ memory-region = <&wlan_mem>;
+
+ vdd-0.8-cx-mx-supply = <&vreg_l1e_0p75>;
+ vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l9a_1p3>;
+ vdd-3.3-ch0-supply = <&vreg_l11c_3p3>;
+ vdd-3.3-ch1-supply = <&vreg_l10c_3p3>;
+
+ status = "okay";
+};
+
+&xo_board_clk {
+ clock-frequency = <38400000>;
+};
+
+/* PINCTRL */
+
+&pmc8180c_gpios {
+ bl_pwm_default_state: bl-pwm-default-state {
+ en {
+ pins = "gpio8";
+ function = "normal";
+ };
+
+ pwm {
+ pins = "gpio10";
+ function = "func1";
+ };
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <47 4>, <126 4>;
+
+ aux_i2c_active_state: aux-i2c-active-state {
+ pins = "gpio98", "gpio99";
+ function = "qup7";
+
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ edp_hpd_active: epd-hpd-active-state {
+ pins = "gpio10";
+ function = "edp_hot";
+ };
+
+ hall_int_active_state: hall-int-active-state {
+ pins = "gpio121";
+ function = "gpio";
+
+ input-enable;
+ bias-disable;
+ };
+
+ kb_int_active_state: kb-int-active-state {
+ int-n {
+ pins = "gpio37";
+ function = "gpio";
+
+ bias-pull-up;
+ intput-enable;
+ };
+
+ kp-disable {
+ pins = "gpio135";
+ function = "gpio";
+
+ output-high;
+ };
+ };
+
+ kb_tp_3v3_en_active_state: kb-tp-3v3-en-active-state {
+ pins = "gpio4";
+ function = "gpio";
+
+ bias-disable;
+ };
+
+ pcie2_default_state: pcie2-default-state {
+ clkreq {
+ pins = "gpio176";
+ function = "pci_e2";
+ bias-pull-up;
+ };
+
+ reset-n {
+ pins = "gpio175";
+ function = "gpio";
+
+ drive-strength = <2>;
+ output-low;
+ bias-pull-down;
+ };
+
+ wake-n {
+ pins = "gpio177";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ tp_int_active_state: tp-int-active-state {
+ tp-int {
+ pins = "gpio24";
+ function = "gpio";
+
+ bias-disable;
+ input-enable;
+ };
+
+ tp-close-n {
+ pins = "gpio116";
+ function = "gpio";
+
+ bias-disable;
+ input-enable;
+ };
+ };
+
+ ts_active_state: ts-active-state {
+ int-n {
+ pins = "gpio122";
+ function = "gpio";
+
+ input-enable;
+ bias-disable;
+ };
+
+ reset-n {
+ pins = "gpio54";
+ function = "gpio";
+
+ output-high;
+ };
+ };
+
+ ts_i2c_active_state: ts-i2c-active-state {
+ pins = "gpio114", "gpio115";
+ function = "qup1";
+
+ /* External pull up */
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ uart13_state: uart13-state {
+ cts {
+ pins = "gpio43";
+ function = "qup13";
+ bias-pull-down;
+ };
+
+ rts-tx {
+ pins = "gpio44", "gpio45";
+ function = "qup13";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio46";
+ function = "qup13";
+ bias-pull-up;
+ };
+ };
+};