| Message ID | 20230510134121.1232286-8-quic_srichara@quicinc.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add minimal boot support for IPQ5018 | expand |
On 10/05/2023 15:41, Sricharan Ramabadhran wrote: > Add initial device tree support for the Qualcomm IPQ5018 SoC and > rdp432-c2 board. > > Co-developed-by: Varadarajan Narayanan <quic_varada@quicinc.com> > Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com> > Co-developed-by: Gokul Sriram Palanisamy <quic_gokulsri@quicinc.com> > Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri@quicinc.com> > Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com> > --- > [v4] Fixed the address range for intc v2m nodes > Fixed all schema check warnings > Added cache-unified and cache-size property for l2 cache node > Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Best regards, Krzysztof
On 10. 05. 2023. 15:41, Sricharan Ramabadhran wrote: > Add initial device tree support for the Qualcomm IPQ5018 SoC and > rdp432-c2 board. Hi, does reboot work for you with this patchset? I have tested on 2 different IPQ5018 boards and they wont reboot, I get the: Requesting system reboot [ 321.005977] qcom_scm firmware:scm: No available mechanism for setting download mode [ 321.006128] reboot: Restarting system And then it just hangs there. Regards, Robert > > Co-developed-by: Varadarajan Narayanan <quic_varada@quicinc.com> > Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com> > Co-developed-by: Gokul Sriram Palanisamy <quic_gokulsri@quicinc.com> > Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri@quicinc.com> > Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com> > --- > [v4] Fixed the address range for intc v2m nodes > Fixed all schema check warnings > Added cache-unified and cache-size property for l2 cache node > > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../arm64/boot/dts/qcom/ipq5018-rdp432-c2.dts | 72 +++++ > arch/arm64/boot/dts/qcom/ipq5018.dtsi | 250 ++++++++++++++++++ > 3 files changed, 323 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/ipq5018-rdp432-c2.dts > create mode 100644 arch/arm64/boot/dts/qcom/ipq5018.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index d42c59572ace..57858e7f2095 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb > +dtb-$(CONFIG_ARCH_QCOM) += ipq5018-rdp432-c2.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq5332-mi01.2.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq5332-rdp468.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb > diff --git a/arch/arm64/boot/dts/qcom/ipq5018-rdp432-c2.dts b/arch/arm64/boot/dts/qcom/ipq5018-rdp432-c2.dts > new file mode 100644 > index 000000000000..e636a1cb9b77 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/ipq5018-rdp432-c2.dts > @@ -0,0 +1,72 @@ > +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause > +/* > + * IPQ5018 MP03.1-C2 board device tree source > + * > + * Copyright (c) 2023 The Linux Foundation. All rights reserved. > + */ > + > +/dts-v1/; > + > +#include "ipq5018.dtsi" > + > +/ { > + model = "Qualcomm Technologies, Inc. IPQ5018/AP-RDP432.1-C2"; > + compatible = "qcom,ipq5018-rdp432-c2", "qcom,ipq5018"; > + > + aliases { > + serial0 = &blsp1_uart1; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > +}; > + > +&blsp1_uart1 { > + pinctrl-0 = <&uart1_pins>; > + pinctrl-names = "default"; > + status = "okay"; > +}; > + > +&sdhc_1 { > + pinctrl-0 = <&sdc_default_state>; > + pinctrl-names = "default"; > + mmc-ddr-1_8v; > + mmc-hs200-1_8v; > + max-frequency = <192000000>; > + bus-width = <4>; > + status = "okay"; > +}; > + > +&sleep_clk { > + clock-frequency = <32000>; > +}; > + > +&tlmm { > + sdc_default_state: sdc-default-state { > + clk-pins { > + pins = "gpio9"; > + function = "sdc1_clk"; > + drive-strength = <8>; > + bias-disable; > + }; > + > + cmd-pins { > + pins = "gpio8"; > + function = "sdc1_cmd"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + > + data-pins { > + pins = "gpio4", "gpio5", "gpio6", "gpio7"; > + function = "sdc1_data"; > + drive-strength = <8>; > + bias-disable; > + }; > + }; > +}; > + > +&xo_board_clk { > + clock-frequency = <24000000>; > +}; > diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi > new file mode 100644 > index 000000000000..fc31043b59fe > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi > @@ -0,0 +1,250 @@ > +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause > +/* > + * IPQ5018 SoC device tree source > + * > + * Copyright (c) 2023 The Linux Foundation. All rights reserved. > + */ > + > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/clock/qcom,gcc-ipq5018.h> > +#include <dt-bindings/reset/qcom,gcc-ipq5018.h> > + > +/ { > + interrupt-parent = <&intc>; > + #address-cells = <2>; > + #size-cells = <2>; > + > + clocks { > + sleep_clk: sleep-clk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + }; > + > + xo_board_clk: xo-board-clk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + }; > + }; > + > + cpus { > + #address-cells = <1>; > + #size-cells = <0>; > + > + CPU0: cpu@0 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0x0>; > + enable-method = "psci"; > + next-level-cache = <&L2_0>; > + }; > + > + CPU1: cpu@1 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0x1>; > + enable-method = "psci"; > + next-level-cache = <&L2_0>; > + }; > + > + L2_0: l2-cache { > + compatible = "cache"; > + cache-level = <2>; > + cache-size = <0x80000>; > + cache-unified; > + }; > + }; > + > + firmware { > + scm { > + compatible = "qcom,scm-ipq5018", "qcom,scm"; > + }; > + }; > + > + memory@40000000 { > + device_type = "memory"; > + /* We expect the bootloader to fill in the size */ > + reg = <0x0 0x40000000 0x0 0x0>; > + }; > + > + pmu { > + compatible = "arm,cortex-a53-pmu"; > + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; > + }; > + > + psci { > + compatible = "arm,psci-1.0"; > + method = "smc"; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + tz_region: tz@4ac00000 { > + reg = <0x0 0x4ac00000 0x0 0x400000>; > + no-map; > + }; > + }; > + > + soc: soc@0 { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0 0 0 0xffffffff>; > + > + tlmm: pinctrl@1000000 { > + compatible = "qcom,ipq5018-tlmm"; > + reg = <0x01000000 0x300000>; > + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&tlmm 0 0 47>; > + interrupt-controller; > + #interrupt-cells = <2>; > + > + uart1_pins: uart1-state { > + pins = "gpio31", "gpio32", "gpio33", "gpio34"; > + function = "blsp1_uart1"; > + drive-strength = <8>; > + bias-pull-down; > + }; > + }; > + > + gcc: clock-controller@1800000 { > + compatible = "qcom,gcc-ipq5018"; > + reg = <0x01800000 0x80000>; > + clocks = <&xo_board_clk>, > + <&sleep_clk>, > + <0>, > + <0>, > + <0>, > + <0>, > + <0>, > + <0>, > + <0>; > + #clock-cells = <1>; > + #reset-cells = <1>; > + #power-domain-cells = <1>; > + }; > + > + sdhc_1: mmc@7804000 { > + compatible = "qcom,ipq5018-sdhci", "qcom,sdhci-msm-v5"; > + reg = <0x7804000 0x1000>; > + reg-names = "hc"; > + > + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "hc_irq", "pwr_irq"; > + > + clocks = <&gcc GCC_SDCC1_AHB_CLK>, > + <&gcc GCC_SDCC1_APPS_CLK>, > + <&xo_board_clk>; > + clock-names = "iface", "core", "xo"; > + non-removable; > + status = "disabled"; > + }; > + > + blsp1_uart1: serial@78af000 { > + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; > + reg = <0x078af000 0x200>; > + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, > + <&gcc GCC_BLSP1_AHB_CLK>; > + clock-names = "core", "iface"; > + status = "disabled"; > + }; > + > + intc: interrupt-controller@b000000 { > + compatible = "qcom,msm-qgic2"; > + reg = <0x0b000000 0x1000>, /* GICD */ > + <0x0b002000 0x2000>, /* GICC */ > + <0x0b001000 0x1000>, /* GICH */ > + <0x0b004000 0x2000>; /* GICV */ > + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; > + interrupt-controller; > + #interrupt-cells = <3>; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0 0x0b00a000 0x1ffa>; > + > + v2m0: v2m@0 { > + compatible = "arm,gic-v2m-frame"; > + reg = <0x00000000 0xff8>; > + msi-controller; > + }; > + > + v2m1: v2m@1000 { > + compatible = "arm,gic-v2m-frame"; > + reg = <0x00001000 0xff8>; > + msi-controller; > + }; > + }; > + > + timer@b120000 { > + compatible = "arm,armv7-timer-mem"; > + reg = <0x0b120000 0x1000>; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + frame@b120000 { > + reg = <0x0b121000 0x1000>, > + <0x0b122000 0x1000>; > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; > + frame-number = <0>; > + }; > + > + frame@b123000 { > + reg = <0xb123000 0x1000>; > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > + frame-number = <1>; > + status = "disabled"; > + }; > + > + frame@b124000 { > + frame-number = <2>; > + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b124000 0x1000>; > + status = "disabled"; > + }; > + > + frame@b125000 { > + reg = <0x0b125000 0x1000>; > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > + frame-number = <3>; > + status = "disabled"; > + }; > + > + frame@b126000 { > + reg = <0x0b126000 0x1000>; > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > + frame-number = <4>; > + status = "disabled"; > + }; > + > + frame@b127000 { > + reg = <0x0b127000 0x1000>; > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > + frame-number = <5>; > + status = "disabled"; > + }; > + > + frame@b128000 { > + reg = <0x0b128000 0x1000>; > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > + frame-number = <6>; > + status = "disabled"; > + }; > + }; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; > + }; > +};
On 5/11/2023 3:54 PM, Robert Marko wrote: > > On 10. 05. 2023. 15:41, Sricharan Ramabadhran wrote: >> Add initial device tree support for the Qualcomm IPQ5018 SoC and >> rdp432-c2 board. > > Hi, does reboot work for you with this patchset? > I have tested on 2 different IPQ5018 boards and they wont reboot, > I get the: > Requesting system reboot > [ 321.005977] qcom_scm firmware:scm: No available mechanism for setting > download mode > [ 321.006128] reboot: Restarting system > > And then it just hangs there. > Yes, that is because SDI disabling using separate SCM is still not there. I will add support for that in a separate series. Regards, Sricharan
On Thu, 11 May 2023 at 12:54, Sricharan Ramabadhran <quic_srichara@quicinc.com> wrote: > > > > On 5/11/2023 3:54 PM, Robert Marko wrote: > > > > On 10. 05. 2023. 15:41, Sricharan Ramabadhran wrote: > >> Add initial device tree support for the Qualcomm IPQ5018 SoC and > >> rdp432-c2 board. > > > > Hi, does reboot work for you with this patchset? > > I have tested on 2 different IPQ5018 boards and they wont reboot, > > I get the: > > Requesting system reboot > > [ 321.005977] qcom_scm firmware:scm: No available mechanism for setting > > download mode > > [ 321.006128] reboot: Restarting system > > > > And then it just hangs there. > > > > Yes, that is because SDI disabling using separate SCM is still not > there. I will add support for that in a separate series. Do you maybe have a workaround for this, as it's driving me crazy to have to pull power? Also, it would probably be good to note this in the commit to avoid more questions like this. Regards, Robert > > Regards, > Sricharan
On 5/11/2023 4:29 PM, Robert Marko wrote: > On Thu, 11 May 2023 at 12:54, Sricharan Ramabadhran > <quic_srichara@quicinc.com> wrote: >> >> >> >> On 5/11/2023 3:54 PM, Robert Marko wrote: >>> >>> On 10. 05. 2023. 15:41, Sricharan Ramabadhran wrote: >>>> Add initial device tree support for the Qualcomm IPQ5018 SoC and >>>> rdp432-c2 board. >>> >>> Hi, does reboot work for you with this patchset? >>> I have tested on 2 different IPQ5018 boards and they wont reboot, >>> I get the: >>> Requesting system reboot >>> [ 321.005977] qcom_scm firmware:scm: No available mechanism for setting >>> download mode >>> [ 321.006128] reboot: Restarting system >>> >>> And then it just hangs there. >>> >> >> Yes, that is because SDI disabling using separate SCM is still not >> there. I will add support for that in a separate series. > > Do you maybe have a workaround for this, as it's driving me crazy to > have to pull power? > Also, it would probably be good to note this in the commit to avoid > more questions like this. > Infact, no workaround. Only way is to add those additional SCM calls. That said, i will add this in the commit log here. Regards, Sricharan
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index d42c59572ace..57858e7f2095 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb +dtb-$(CONFIG_ARCH_QCOM) += ipq5018-rdp432-c2.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq5332-mi01.2.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq5332-rdp468.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb diff --git a/arch/arm64/boot/dts/qcom/ipq5018-rdp432-c2.dts b/arch/arm64/boot/dts/qcom/ipq5018-rdp432-c2.dts new file mode 100644 index 000000000000..e636a1cb9b77 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq5018-rdp432-c2.dts @@ -0,0 +1,72 @@ +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause +/* + * IPQ5018 MP03.1-C2 board device tree source + * + * Copyright (c) 2023 The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include "ipq5018.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. IPQ5018/AP-RDP432.1-C2"; + compatible = "qcom,ipq5018-rdp432-c2", "qcom,ipq5018"; + + aliases { + serial0 = &blsp1_uart1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&uart1_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&sdhc_1 { + pinctrl-0 = <&sdc_default_state>; + pinctrl-names = "default"; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + max-frequency = <192000000>; + bus-width = <4>; + status = "okay"; +}; + +&sleep_clk { + clock-frequency = <32000>; +}; + +&tlmm { + sdc_default_state: sdc-default-state { + clk-pins { + pins = "gpio9"; + function = "sdc1_clk"; + drive-strength = <8>; + bias-disable; + }; + + cmd-pins { + pins = "gpio8"; + function = "sdc1_cmd"; + drive-strength = <8>; + bias-pull-up; + }; + + data-pins { + pins = "gpio4", "gpio5", "gpio6", "gpio7"; + function = "sdc1_data"; + drive-strength = <8>; + bias-disable; + }; + }; +}; + +&xo_board_clk { + clock-frequency = <24000000>; +}; diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi new file mode 100644 index 000000000000..fc31043b59fe --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi @@ -0,0 +1,250 @@ +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause +/* + * IPQ5018 SoC device tree source + * + * Copyright (c) 2023 The Linux Foundation. All rights reserved. + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/qcom,gcc-ipq5018.h> +#include <dt-bindings/reset/qcom,gcc-ipq5018.h> + +/ { + interrupt-parent = <&intc>; + #address-cells = <2>; + #size-cells = <2>; + + clocks { + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + xo_board_clk: xo-board-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + L2_0: l2-cache { + compatible = "cache"; + cache-level = <2>; + cache-size = <0x80000>; + cache-unified; + }; + }; + + firmware { + scm { + compatible = "qcom,scm-ipq5018", "qcom,scm"; + }; + }; + + memory@40000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0x0 0x40000000 0x0 0x0>; + }; + + pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + tz_region: tz@4ac00000 { + reg = <0x0 0x4ac00000 0x0 0x400000>; + no-map; + }; + }; + + soc: soc@0 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq5018-tlmm"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 47>; + interrupt-controller; + #interrupt-cells = <2>; + + uart1_pins: uart1-state { + pins = "gpio31", "gpio32", "gpio33", "gpio34"; + function = "blsp1_uart1"; + drive-strength = <8>; + bias-pull-down; + }; + }; + + gcc: clock-controller@1800000 { + compatible = "qcom,gcc-ipq5018"; + reg = <0x01800000 0x80000>; + clocks = <&xo_board_clk>, + <&sleep_clk>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + + sdhc_1: mmc@7804000 { + compatible = "qcom,ipq5018-sdhci", "qcom,sdhci-msm-v5"; + reg = <0x7804000 0x1000>; + reg-names = "hc"; + + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_AHB_CLK>, + <&gcc GCC_SDCC1_APPS_CLK>, + <&xo_board_clk>; + clock-names = "iface", "core", "xo"; + non-removable; + status = "disabled"; + }; + + blsp1_uart1: serial@78af000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x078af000 0x200>; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + intc: interrupt-controller@b000000 { + compatible = "qcom,msm-qgic2"; + reg = <0x0b000000 0x1000>, /* GICD */ + <0x0b002000 0x2000>, /* GICC */ + <0x0b001000 0x1000>, /* GICH */ + <0x0b004000 0x2000>; /* GICV */ + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + interrupt-controller; + #interrupt-cells = <3>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0b00a000 0x1ffa>; + + v2m0: v2m@0 { + compatible = "arm,gic-v2m-frame"; + reg = <0x00000000 0xff8>; + msi-controller; + }; + + v2m1: v2m@1000 { + compatible = "arm,gic-v2m-frame"; + reg = <0x00001000 0xff8>; + msi-controller; + }; + }; + + timer@b120000 { + compatible = "arm,armv7-timer-mem"; + reg = <0x0b120000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + frame@b120000 { + reg = <0x0b121000 0x1000>, + <0x0b122000 0x1000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + frame-number = <0>; + }; + + frame@b123000 { + reg = <0xb123000 0x1000>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + frame-number = <1>; + status = "disabled"; + }; + + frame@b124000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b124000 0x1000>; + status = "disabled"; + }; + + frame@b125000 { + reg = <0x0b125000 0x1000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + frame-number = <3>; + status = "disabled"; + }; + + frame@b126000 { + reg = <0x0b126000 0x1000>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + frame-number = <4>; + status = "disabled"; + }; + + frame@b127000 { + reg = <0x0b127000 0x1000>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + frame-number = <5>; + status = "disabled"; + }; + + frame@b128000 { + reg = <0x0b128000 0x1000>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + frame-number = <6>; + status = "disabled"; + }; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; +};