diff mbox series

[v9,10/10] serial: sc16is7xx: improve comments about variants

Message ID 20230725142343.1724130-11-hugo@hugovil.com
State New
Headers show
Series serial: sc16is7xx: fix GPIO regression and rs485 improvements | expand

Commit Message

Hugo Villeneuve July 25, 2023, 2:23 p.m. UTC 
From: Hugo Villeneuve <hvilleneuve@dimonoff.com>

Replace 740/750/760 with generic terms like 74x/75x/76x to account for
variants like 741, 752 and 762.

Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
---
 drivers/tty/serial/sc16is7xx.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

Comments

Greg KH July 31, 2023, 3:56 p.m. UTC | #1 
On Tue, Jul 25, 2023 at 10:23:42AM -0400, Hugo Villeneuve wrote:
> From: Hugo Villeneuve <hvilleneuve@dimonoff.com>
> 
> Replace 740/750/760 with generic terms like 74x/75x/76x to account for
> variants like 741, 752 and 762.
> 
> Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
> Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>

You have now mixed a patch series full of commits that are to be
backported to stable kernels (i.e. fixes) and general changes that do
not need to be.

Please make these two separate patch series, you can have one depend on
the other, but I can't apply them both to the "for Linus" branch as
obviously they are not all fixes nor need to go to Linus now.

thanks,

greg k-h
Hugo Villeneuve Aug. 3, 2023, 1:28 p.m. UTC | #2 
On Mon, 31 Jul 2023 17:56:53 +0200
Greg KH <gregkh@linuxfoundation.org> wrote:

> On Tue, Jul 25, 2023 at 10:23:42AM -0400, Hugo Villeneuve wrote:
> > From: Hugo Villeneuve <hvilleneuve@dimonoff.com>
> > 
> > Replace 740/750/760 with generic terms like 74x/75x/76x to account for
> > variants like 741, 752 and 762.
> > 
> > Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
> > Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
> 
> You have now mixed a patch series full of commits that are to be
> backported to stable kernels (i.e. fixes) and general changes that do
> not need to be.
> 
> Please make these two separate patch series, you can have one depend on
> the other, but I can't apply them both to the "for Linus" branch as
> obviously they are not all fixes nor need to go to Linus now.
> 
> thanks,
> 
> greg k-h

Hi,
Ok, will do.

Thank you,
Hugo.
diff mbox series

Patch

diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index 718e982e1efe..d6851360ef7d 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -223,7 +223,7 @@ 
  * trigger levels. Trigger levels from 4 characters to 60 characters are
  * available with a granularity of four.
  *
- * When the trigger level setting in TLR is zero, the SC16IS740/750/760 uses the
+ * When the trigger level setting in TLR is zero, the SC16IS74x/75x/76x uses the
  * trigger level setting defined in FCR. If TLR has non-zero trigger level value
  * the trigger level defined in FCR is discarded. This applies to both transmit
  * FIFO and receive FIFO trigger level setting.
@@ -234,7 +234,7 @@ 
 #define SC16IS7XX_TLR_TX_TRIGGER(words)	((((words) / 4) & 0x0f) << 0)
 #define SC16IS7XX_TLR_RX_TRIGGER(words)	((((words) / 4) & 0x0f) << 4)
 
-/* IOControl register bits (Only 750/760) */
+/* IOControl register bits (Only 75x/76x) */
 #define SC16IS7XX_IOCONTROL_LATCH_BIT	(1 << 0) /* Enable input latching */
 #define SC16IS7XX_IOCONTROL_MODEM_A_BIT	(1 << 1) /* Enable GPIO[7:4] as modem A pins */
 #define SC16IS7XX_IOCONTROL_MODEM_B_BIT	(1 << 2) /* Enable GPIO[3:0] as modem B pins */
@@ -249,9 +249,9 @@ 
 #define SC16IS7XX_EFCR_RTS_INVERT_BIT	(1 << 5) /* RTS output inversion */
 #define SC16IS7XX_EFCR_IRDA_MODE_BIT	(1 << 7) /* IrDA mode
 						  * 0 = rate upto 115.2 kbit/s
-						  *   - Only 750/760
+						  *   - Only 75x/76x
 						  * 1 = rate upto 1.152 Mbit/s
-						  *   - Only 760
+						  *   - Only 76x
 						  */
 
 /* EFR register bits */