| Message ID | 20231005035525.19036-5-chanh@os.amperecomputing.com |
|---|---|
| State | New |
| Headers | show |
| Series | Update the device tree for Ampere's BMC platform | expand |
On 05/10/2023 05:55, Chanh Nguyen wrote: > Use gpio-leds to configure GPIOW5 to GPIO_ACTIVE_HIGH and > GPIO_TRANSITORY flags as a bmc ready led. The GPIOW5 pin > is reset when watchdog timeout occurs. > > Configure the GPIOS3 to GPIO_ACTIVE_HIGH as an identify led. > > Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com> > --- > .../dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts | 13 +++++++++++++ > 1 file changed, 13 insertions(+) > > diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts > index b7c4f7cfad07..88693c2b2dbe 100644 > --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts > +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts > @@ -51,6 +51,19 @@ > }; > }; > > + leds { > + compatible = "gpio-leds"; > + > + bmc-ready { Missing led name. It does not look like you tested the DTS against bindings. Please run `make dtbs_check W=1` (see Documentation/devicetree/bindings/writing-schema.rst or https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/ for instructions). Best regards, Krzysztof
On 05/10/2023 14:31, Krzysztof Kozlowski wrote: > On 05/10/2023 05:55, Chanh Nguyen wrote: >> Use gpio-leds to configure GPIOW5 to GPIO_ACTIVE_HIGH and >> GPIO_TRANSITORY flags as a bmc ready led. The GPIOW5 pin >> is reset when watchdog timeout occurs. >> >> Configure the GPIOS3 to GPIO_ACTIVE_HIGH as an identify led. >> >> Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com> >> --- >> .../dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts | 13 +++++++++++++ >> 1 file changed, 13 insertions(+) >> >> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts >> index b7c4f7cfad07..88693c2b2dbe 100644 >> --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts >> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts >> @@ -51,6 +51,19 @@ >> }; >> }; >> >> + leds { >> + compatible = "gpio-leds"; >> + >> + bmc-ready { > > Missing led name. > > It does not look like you tested the DTS against bindings. Please run > `make dtbs_check W=1` (see > Documentation/devicetree/bindings/writing-schema.rst or > https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/ > for instructions). > > Best regards, > Krzysztof > Thank Krzysztof! I'll test the DTS against bindings and update it in patch series v2.
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts index b7c4f7cfad07..88693c2b2dbe 100644 --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts @@ -51,6 +51,19 @@ }; }; + leds { + compatible = "gpio-leds"; + + bmc-ready { + gpios = <&gpio0 ASPEED_GPIO(W, 5) (GPIO_ACTIVE_HIGH | + GPIO_TRANSITORY)>; + }; + + identify { + gpios = <&gpio0 ASPEED_GPIO(S, 3) GPIO_ACTIVE_HIGH>; + }; + }; + voltage_mon_reg: voltage-mon-regulator { compatible = "regulator-fixed"; regulator-name = "ltc2497_reg";
Use gpio-leds to configure GPIOW5 to GPIO_ACTIVE_HIGH and GPIO_TRANSITORY flags as a bmc ready led. The GPIOW5 pin is reset when watchdog timeout occurs. Configure the GPIOS3 to GPIO_ACTIVE_HIGH as an identify led. Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com> --- .../dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+)