diff mbox series

[3/3] arm64: dts: qcom: sdm450: add Lenovo Smart Tab M10 DTS

Message ID 20240523-topic-sdm450-upstream-tbx605f-v1-3-e52b89133226@linaro.org
State Accepted
Commit 7ddab80e115086c0f2f37fa5a95466d0885d66d2
Headers show
Series [1/3] dt-bindings: arm: qcom: Add Lenovo Smart Tab M10 (WiFi) | expand

Commit Message

Neil Armstrong May 23, 2024, 7:59 a.m. UTC
This add initial support for the Lenovo Smart Tab M10 (WiFi)
(model tbx605f) which is a 10.1" tablet by Lenovo based on the
SDM450 SoC.

It has a 10.1" LCP touch panel, SDCard slot, Volume+Power buttons,
USB-C port amd front-facing camera (not supported).

The proper LCP Panel support will be added later, for now using the
simeple-framebuffer with the bootloader-initialized video memory.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/boot/dts/qcom/Makefile                  |   1 +
 arch/arm64/boot/dts/qcom/sdm450-lenovo-tbx605f.dts | 276 +++++++++++++++++++++
 2 files changed, 277 insertions(+)

Comments

Bjorn Andersson May 27, 2024, 4:33 p.m. UTC | #1
On Thu, May 23, 2024 at 09:59:35AM GMT, Neil Armstrong wrote:
> diff --git a/arch/arm64/boot/dts/qcom/sdm450-lenovo-tbx605f.dts b/arch/arm64/boot/dts/qcom/sdm450-lenovo-tbx605f.dts
[..]
> +&rpm_requests {
> +	regulators {
> +		compatible = "qcom,rpm-pm8953-regulators";
[..]
> +		pm8953_l8: l8 {
> +			regulator-min-microvolt = <2900000>;
> +			regulator-max-microvolt = <2900000>;
> +		};
[..]
> +		pm8953_l11: l11 {
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +		};
[..]
> +	};
> +};
> +
> +&sdhc_1 {
> +	vmmc-supply = <&pm8953_l8>;

JFYI. Not ensuring that the vmmc-supply is in HPM mode bitten us
multiple times in the past. 

Regards,
Bjorn
Bjorn Andersson May 28, 2024, 5:22 p.m. UTC | #2
On Tue, May 28, 2024 at 02:19:28PM GMT, Konrad Dybcio wrote:
> 
> 
> On 5/27/24 18:33, Bjorn Andersson wrote:
> > On Thu, May 23, 2024 at 09:59:35AM GMT, Neil Armstrong wrote:
> > > diff --git a/arch/arm64/boot/dts/qcom/sdm450-lenovo-tbx605f.dts b/arch/arm64/boot/dts/qcom/sdm450-lenovo-tbx605f.dts
> > [..]
> > > +&rpm_requests {
> > > +	regulators {
> > > +		compatible = "qcom,rpm-pm8953-regulators";
> > [..]
> > > +		pm8953_l8: l8 {
> > > +			regulator-min-microvolt = <2900000>;
> > > +			regulator-max-microvolt = <2900000>;
> > > +		};
> > [..]
> > > +		pm8953_l11: l11 {
> > > +			regulator-min-microvolt = <3300000>;
> > > +			regulator-max-microvolt = <3300000>;
> > > +		};
> > [..]
> > > +	};
> > > +};
> > > +
> > > +&sdhc_1 {
> > > +	vmmc-supply = <&pm8953_l8>;
> > 
> > JFYI. Not ensuring that the vmmc-supply is in HPM mode bitten us
> > multiple times in the past.
> 
> it's not rpmh ;)
> 

Here are a few non-rpmh examples of us being bitten...

e38161bd325e ("arm64: dts: apq8096-db820c: Increase load on l21 for SDCARD")
03864e57770a ("ARM: dts: qcom: msm8974-hammerhead: increase load on l20 for sdhci")
27fe0fc05f35 ("ARM: dts: msm8974-FP2: Increase load on l20 for sdhci")

...taken care of by forcing the relevant regulators into HPM.

Regards,
Bjorn
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 7d40ec5e7d21..f163eedd2af2 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -175,6 +175,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= sc8180x-primus.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc8280xp-crd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc8280xp-lenovo-thinkpad-x13s.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sda660-inforce-ifc6560.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm450-lenovo-tbx605f.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm450-motorola-ali.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-ganges-kirin.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-discovery.dtb
diff --git a/arch/arm64/boot/dts/qcom/sdm450-lenovo-tbx605f.dts b/arch/arm64/boot/dts/qcom/sdm450-lenovo-tbx605f.dts
new file mode 100644
index 000000000000..175befc02b22
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm450-lenovo-tbx605f.dts
@@ -0,0 +1,276 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Neil Armstrong <neil.armstrong@linaro.org>
+ */
+/dts-v1/;
+
+#include "sdm450.dtsi"
+#include "pm8953.dtsi"
+#include "pmi8950.dtsi"
+
+/ {
+	model = "Lenovo Smart Tab M10";
+	compatible = "lenovo,tbx605f", "qcom,sdm450";
+	chassis-type = "tablet";
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer@90001000 {
+			compatible = "simple-framebuffer";
+			reg = <0 0x90001000 0 (1200 * 1920 * 3)>;
+
+			width = <1200>;
+			height = <1920>;
+			stride = <(1200 * 3)>;
+			format = "r8g8b8";
+
+			power-domains = <&gcc MDSS_GDSC>;
+
+			clocks = <&gcc GCC_MDSS_AHB_CLK>,
+				 <&gcc GCC_MDSS_AXI_CLK>,
+				 <&gcc GCC_MDSS_VSYNC_CLK>,
+				 <&gcc GCC_MDSS_MDP_CLK>,
+				 <&gcc GCC_MDSS_BYTE0_CLK>,
+				 <&gcc GCC_MDSS_PCLK0_CLK>,
+				 <&gcc GCC_MDSS_ESC0_CLK>;
+		};
+	};
+
+	reserved-memory {
+		other_ext_region@0 {
+			no-map;
+			reg = <0x00 0x84500000 0x00 0x2300000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&tlmm 85 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&hsusb_phy {
+	vdd-supply = <&pm8953_l3>;
+	vdda-pll-supply = <&pm8953_l7>;
+	vdda-phy-dpdm-supply = <&pm8953_l13>;
+
+	status = "okay";
+};
+
+&i2c_3 {
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5506";
+		reg = <0x38>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <65 IRQ_TYPE_EDGE_FALLING>;
+		vcc-supply = <&pm8953_l10>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_active &ts_reset_active>;
+
+		reset-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <1200>;
+		touchscreen-size-y = <1920>;
+	};
+};
+
+&pm8953_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8953-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_l1-supply = <&pm8953_s3>;
+		vdd_l2_l3-supply = <&pm8953_s3>;
+		vdd_l4_l5_l6_l7_l16_l19-supply = <&pm8953_s4>;
+		vdd_l8_l11_l12_l13_l14_l15-supply = <&vph_pwr>;
+		vdd_l9_l10_l17_l18_l22-supply = <&vph_pwr>;
+
+		pm8953_s1: s1 {
+			regulator-min-microvolt = <870000>;
+			regulator-max-microvolt = <1156000>;
+		};
+
+		pm8953_s3: s3 {
+			regulator-min-microvolt = <1224000>;
+			regulator-max-microvolt = <1224000>;
+		};
+
+		pm8953_s4: s4 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8953_l1: l1 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		pm8953_l2: l2 {
+			regulator-min-microvolt = <975000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8953_l3: l3 {
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <925000>;
+		};
+
+		pm8953_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8953_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8953_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1900000>;
+		};
+
+		pm8953_l8: l8 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+		};
+
+		pm8953_l9: l9 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8953_l10: l10 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8953_l11: l11 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8953_l12: l12 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8953_l13: l13 {
+			regulator-min-microvolt = <3125000>;
+			regulator-max-microvolt = <3125000>;
+		};
+
+		pm8953_l16: l16 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8953_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8953_l19: l19 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8953_l22: l22 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8953_l23: l23 {
+			regulator-min-microvolt = <975000>;
+			regulator-max-microvolt = <1225000>;
+		};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8953_l8>;
+	vqmmc-supply = <&pm8953_l5>;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8953_l11>;
+	vqmmc-supply = <&pm8953_l12>;
+
+	cd-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_off>;
+	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <135 4>;
+
+	ts_int_active: ts-int-active-state {
+		pins = "gpio65";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	ts_reset_active: ts-reset-active-state {
+		pins = "gpio64";
+		function = "gpio";
+		drive-strength = <0x08>;
+		bias-pull-up;
+	};
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&wcnss {
+	vddpx-supply = <&pm8953_l5>;
+
+	status = "okay";
+};
+
+&wcnss_iris {
+	compatible = "qcom,wcn3660b";
+
+	vddxo-supply = <&pm8953_l7>;
+	vddrfa-supply = <&pm8953_l19>;
+	vddpa-supply = <&pm8953_l9>;
+	vdddig-supply = <&pm8953_l5>;
+};