diff mbox series

[v2,10/13] pinctrl: renesas: pinctrl-rzg2l: Add support to set pulling up/down the pins

Message ID 20240423175900.702640-11-prabhakar.mahadev-lad.rj@bp.renesas.com
State New
Headers show
Series Add PFC support for Renesas RZ/V2H(P) SoC | expand

Commit Message

Lad, Prabhakar April 23, 2024, 5:58 p.m. UTC 
From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>

Add support to configure bias-disable, bias-pull-up and bias-pull-down
properties of the pin.

Two new function pointers get_bias_param() and get_bias_val() are
introduced as the values in PUPD register differ when compared to
RZ/G2L family and RZ/V2H(P) SoC,

Value | RZ/G2L        | RZ/V2H
---------------------------------
00b:  | Bias Disabled | Pull up/down disabled
01b:  | Pull-up       | Pull up/down disabled
10b:  | Pull-down     | Pull-down
11b:  | Prohibited    | Pull-up

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
RFC->v2
- New patch
---
 drivers/pinctrl/renesas/pinctrl-rzg2l.c | 73 +++++++++++++++++++++++++
 1 file changed, 73 insertions(+)

Comments

Geert Uytterhoeven May 22, 2024, 1:14 p.m. UTC | #1 
Hi Prabhakar,

On Tue, Apr 23, 2024 at 7:59 PM Prabhakar <prabhakar.csengg@gmail.com> wrote:
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
>
> Add support to configure bias-disable, bias-pull-up and bias-pull-down
> properties of the pin.
>
> Two new function pointers get_bias_param() and get_bias_val() are
> introduced as the values in PUPD register differ when compared to
> RZ/G2L family and RZ/V2H(P) SoC,
>
> Value | RZ/G2L        | RZ/V2H
> ---------------------------------
> 00b:  | Bias Disabled | Pull up/down disabled
> 01b:  | Pull-up       | Pull up/down disabled
> 10b:  | Pull-down     | Pull-down
> 11b:  | Prohibited    | Pull-up
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> ---
> RFC->v2
> - New patch

Thanks for your patch!

> --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> @@ -1139,6 +1175,25 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
>                 arg = rzg2l_read_pin_config(pctrl, SR(off), bit, SR_MASK);
>                 break;
>
> +       case PIN_CONFIG_BIAS_DISABLE:
> +       case PIN_CONFIG_BIAS_PULL_UP:
> +       case PIN_CONFIG_BIAS_PULL_DOWN: {
> +               if (!(cfg & PIN_CFG_PUPD))
> +                       return -EINVAL;
> +
> +               ret = pctrl->data->get_bias_param(rzg2l_read_pin_config(pctrl,
> +                                                                       PUPD(off),
> +                                                                       bit, PUPD_MASK));

This is rather long, so please split it in two parts, like is done in
other cases in this function:

    arg = rzg2l_read_pin_config(pctrl, PUPD(off), bit, PUPD_MASK);
    ret = pctrl->data->get_bias_param(arg);

> +               if (ret < 0)
> +                       return ret;
> +
> +               if (ret != param)
> +                       return -EINVAL;
> +               /* for PIN_CONFIG_BIAS_PULL_UP/DOWN when enabled we just return 1 */
> +               arg = 1;
> +               break;
> +       }
> +

The rest LGTM.

Gr{oetje,eeting}s,

                        Geert
Geert Uytterhoeven May 22, 2024, 1:26 p.m. UTC | #2 
On Tue, Apr 23, 2024 at 7:59 PM Prabhakar <prabhakar.csengg@gmail.com> wrote:
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
>
> Add support to configure bias-disable, bias-pull-up and bias-pull-down
> properties of the pin.
>
> Two new function pointers get_bias_param() and get_bias_val() are
> introduced as the values in PUPD register differ when compared to
> RZ/G2L family and RZ/V2H(P) SoC,
>
> Value | RZ/G2L        | RZ/V2H
> ---------------------------------
> 00b:  | Bias Disabled | Pull up/down disabled
> 01b:  | Pull-up       | Pull up/down disabled
> 10b:  | Pull-down     | Pull-down
> 11b:  | Prohibited    | Pull-up
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> ---
> RFC->v2
> - New patch
> ---
>  drivers/pinctrl/renesas/pinctrl-rzg2l.c | 73 +++++++++++++++++++++++++
>  1 file changed, 73 insertions(+)
>
> diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> index 102fa75c71d3..c144bf43522b 100644
> --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> @@ -122,6 +122,7 @@
>  #define IOLH(off)              (0x1000 + (off) * 8)
>  #define SR(off)                        (0x1400 + (off) * 8)
>  #define IEN(off)               (0x1800 + (off) * 8)
> +#define PUPD(off)              (0x1C00 + (off) * 8)
>  #define ISEL(off)              (0x2C00 + (off) * 8)
>  #define SD_CH(off, ch)         ((off) + (ch) * 4)
>  #define ETH_POC(off, ch)       ((off) + (ch) * 4)
> @@ -140,6 +141,7 @@
>  #define IEN_MASK               0x01
>  #define IOLH_MASK              0x03
>  #define SR_MASK                        0x01
> +#define PUPD_MASK              0x03
>
>  #define PM_INPUT               0x1
>  #define PM_OUTPUT              0x2
> @@ -265,6 +267,8 @@ struct rzg2l_pinctrl_data {
>         void (*pmc_writeb)(struct rzg2l_pinctrl *pctrl, u8 val, void __iomem *addr);
>         u32 (*read_oen)(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8 pin);
>         int (*write_oen)(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8 pin, u8 oen);
> +       int (*get_bias_param)(u8 val);
> +       int (*get_bias_val)(enum pin_config_param param);

Please use consistent naming: "pmc_writeb" uses <noun>_<verb> ordering,
"get_bias_pararm" uses <verb>_<noun> ordering.

Perhaps "hw_to_bias_param()" and "bias_param_to_hw()?"

Gr{oetje,eeting}s,

                        Geert
Lad, Prabhakar May 28, 2024, 8:01 p.m. UTC | #3 
Hi Geert,

Thank you for the review.

On Wed, May 22, 2024 at 2:14 PM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
>
> Hi Prabhakar,
>
> On Tue, Apr 23, 2024 at 7:59 PM Prabhakar <prabhakar.csengg@gmail.com> wrote:
> > From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> >
> > Add support to configure bias-disable, bias-pull-up and bias-pull-down
> > properties of the pin.
> >
> > Two new function pointers get_bias_param() and get_bias_val() are
> > introduced as the values in PUPD register differ when compared to
> > RZ/G2L family and RZ/V2H(P) SoC,
> >
> > Value | RZ/G2L        | RZ/V2H
> > ---------------------------------
> > 00b:  | Bias Disabled | Pull up/down disabled
> > 01b:  | Pull-up       | Pull up/down disabled
> > 10b:  | Pull-down     | Pull-down
> > 11b:  | Prohibited    | Pull-up
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > ---
> > RFC->v2
> > - New patch
>
> Thanks for your patch!
>
> > --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > @@ -1139,6 +1175,25 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
> >                 arg = rzg2l_read_pin_config(pctrl, SR(off), bit, SR_MASK);
> >                 break;
> >
> > +       case PIN_CONFIG_BIAS_DISABLE:
> > +       case PIN_CONFIG_BIAS_PULL_UP:
> > +       case PIN_CONFIG_BIAS_PULL_DOWN: {
> > +               if (!(cfg & PIN_CFG_PUPD))
> > +                       return -EINVAL;
> > +
> > +               ret = pctrl->data->get_bias_param(rzg2l_read_pin_config(pctrl,
> > +                                                                       PUPD(off),
> > +                                                                       bit, PUPD_MASK));
>
> This is rather long, so please split it in two parts, like is done in
> other cases in this function:
>
>     arg = rzg2l_read_pin_config(pctrl, PUPD(off), bit, PUPD_MASK);
>     ret = pctrl->data->get_bias_param(arg);
>
Agreed, I'll update it as per your suggestion.

Cheers,
Prabhakar
Lad, Prabhakar May 28, 2024, 8:01 p.m. UTC | #4 
Hi Geert,

Thank you for the review.

On Wed, May 22, 2024 at 2:26 PM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
>
> On Tue, Apr 23, 2024 at 7:59 PM Prabhakar <prabhakar.csengg@gmail.com> wrote:
> > From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> >
> > Add support to configure bias-disable, bias-pull-up and bias-pull-down
> > properties of the pin.
> >
> > Two new function pointers get_bias_param() and get_bias_val() are
> > introduced as the values in PUPD register differ when compared to
> > RZ/G2L family and RZ/V2H(P) SoC,
> >
> > Value | RZ/G2L        | RZ/V2H
> > ---------------------------------
> > 00b:  | Bias Disabled | Pull up/down disabled
> > 01b:  | Pull-up       | Pull up/down disabled
> > 10b:  | Pull-down     | Pull-down
> > 11b:  | Prohibited    | Pull-up
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > ---
> > RFC->v2
> > - New patch
> > ---
> >  drivers/pinctrl/renesas/pinctrl-rzg2l.c | 73 +++++++++++++++++++++++++
> >  1 file changed, 73 insertions(+)
> >
> > diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > index 102fa75c71d3..c144bf43522b 100644
> > --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > @@ -122,6 +122,7 @@
> >  #define IOLH(off)              (0x1000 + (off) * 8)
> >  #define SR(off)                        (0x1400 + (off) * 8)
> >  #define IEN(off)               (0x1800 + (off) * 8)
> > +#define PUPD(off)              (0x1C00 + (off) * 8)
> >  #define ISEL(off)              (0x2C00 + (off) * 8)
> >  #define SD_CH(off, ch)         ((off) + (ch) * 4)
> >  #define ETH_POC(off, ch)       ((off) + (ch) * 4)
> > @@ -140,6 +141,7 @@
> >  #define IEN_MASK               0x01
> >  #define IOLH_MASK              0x03
> >  #define SR_MASK                        0x01
> > +#define PUPD_MASK              0x03
> >
> >  #define PM_INPUT               0x1
> >  #define PM_OUTPUT              0x2
> > @@ -265,6 +267,8 @@ struct rzg2l_pinctrl_data {
> >         void (*pmc_writeb)(struct rzg2l_pinctrl *pctrl, u8 val, void __iomem *addr);
> >         u32 (*read_oen)(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8 pin);
> >         int (*write_oen)(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8 pin, u8 oen);
> > +       int (*get_bias_param)(u8 val);
> > +       int (*get_bias_val)(enum pin_config_param param);
>
> Please use consistent naming: "pmc_writeb" uses <noun>_<verb> ordering,
> "get_bias_pararm" uses <verb>_<noun> ordering.
>
> Perhaps "hw_to_bias_param()" and "bias_param_to_hw()?"
>
Ok, I'll rename as suggested above.

Cheers,
Prabhakar
Claudiu Beznea May 30, 2024, 7:48 a.m. UTC | #5 
Hi, Prabhakar,

On 23.04.2024 20:58, Prabhakar wrote:
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> 
> Add support to configure bias-disable, bias-pull-up and bias-pull-down
> properties of the pin.
> 
> Two new function pointers get_bias_param() and get_bias_val() are
> introduced as the values in PUPD register differ when compared to
> RZ/G2L family and RZ/V2H(P) SoC,
> 
> Value | RZ/G2L        | RZ/V2H
> ---------------------------------
> 00b:  | Bias Disabled | Pull up/down disabled
> 01b:  | Pull-up       | Pull up/down disabled
> 10b:  | Pull-down     | Pull-down
> 11b:  | Prohibited    | Pull-up
> 
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> ---
> RFC->v2
> - New patch
> ---
>  drivers/pinctrl/renesas/pinctrl-rzg2l.c | 73 +++++++++++++++++++++++++
>  1 file changed, 73 insertions(+)
> 
> diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> index 102fa75c71d3..c144bf43522b 100644
> --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> @@ -122,6 +122,7 @@
>  #define IOLH(off)		(0x1000 + (off) * 8)
>  #define SR(off)			(0x1400 + (off) * 8)
>  #define IEN(off)		(0x1800 + (off) * 8)
> +#define PUPD(off)		(0x1C00 + (off) * 8)
>  #define ISEL(off)		(0x2C00 + (off) * 8)
>  #define SD_CH(off, ch)		((off) + (ch) * 4)
>  #define ETH_POC(off, ch)	((off) + (ch) * 4)
> @@ -140,6 +141,7 @@
>  #define IEN_MASK		0x01
>  #define IOLH_MASK		0x03
>  #define SR_MASK			0x01
> +#define PUPD_MASK		0x03
>  
>  #define PM_INPUT		0x1
>  #define PM_OUTPUT		0x2
> @@ -265,6 +267,8 @@ struct rzg2l_pinctrl_data {
>  	void (*pmc_writeb)(struct rzg2l_pinctrl *pctrl, u8 val, void __iomem *addr);
>  	u32 (*read_oen)(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8 pin);
>  	int (*write_oen)(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8 pin, u8 oen);
> +	int (*get_bias_param)(u8 val);
> +	int (*get_bias_val)(enum pin_config_param param);
>  };
>  
>  /**
> @@ -1081,6 +1085,38 @@ static int rzg2l_write_oen(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8
>  	return 0;
>  }
>  
> +static int rzg2l_get_bias_param(u8 val)
> +{
> +	switch (val) {
> +	case 0:
> +		return PIN_CONFIG_BIAS_DISABLE;
> +	case 1:
> +		return PIN_CONFIG_BIAS_PULL_UP;
> +	case 2:
> +		return PIN_CONFIG_BIAS_PULL_DOWN;
> +	default:
> +		break;
> +	}
> +
> +	return -EINVAL;
> +}
> +
> +static int rzg2l_get_bias_val(enum pin_config_param param)
> +{
> +	switch (param) {
> +	case PIN_CONFIG_BIAS_DISABLE:
> +		return 0;
> +	case PIN_CONFIG_BIAS_PULL_UP:
> +		return 1;
> +	case PIN_CONFIG_BIAS_PULL_DOWN:
> +		return 2;
> +	default:
> +		break;
> +	}
> +
> +	return -EINVAL;
> +}
> +
>  static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
>  				     unsigned int _pin,
>  				     unsigned long *config)
> @@ -1139,6 +1175,25 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
>  		arg = rzg2l_read_pin_config(pctrl, SR(off), bit, SR_MASK);
>  		break;
>  
> +	case PIN_CONFIG_BIAS_DISABLE:
> +	case PIN_CONFIG_BIAS_PULL_UP:
> +	case PIN_CONFIG_BIAS_PULL_DOWN: {

Block { } can be removed here.

> +		if (!(cfg & PIN_CFG_PUPD))
> +			return -EINVAL;
> +
> +		ret = pctrl->data->get_bias_param(rzg2l_read_pin_config(pctrl,
> +									PUPD(off),
> +									bit, PUPD_MASK));
> +		if (ret < 0)
> +			return ret;
> +
> +		if (ret != param)
> +			return -EINVAL;

Can this happen? Otherwise it can be removed.

> +		/* for PIN_CONFIG_BIAS_PULL_UP/DOWN when enabled we just return 1 */

What about bias disable? I haven't checked in detail, is it OK to do
arg = 1 here?

> +		arg = 1;
> +		break;
> +	}
> +
>  	case PIN_CONFIG_DRIVE_STRENGTH: {
>  		unsigned int index;
>  
> @@ -1254,6 +1309,20 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
>  			rzg2l_rmw_pin_config(pctrl, SR(off), bit, SR_MASK, arg);
>  			break;
>  
> +		case PIN_CONFIG_BIAS_DISABLE:
> +		case PIN_CONFIG_BIAS_PULL_UP:
> +		case PIN_CONFIG_BIAS_PULL_DOWN: {

Block { } can be removed in this case.

> +			if (!(cfg & PIN_CFG_PUPD))
> +				return -EINVAL;
> +
> +			ret = pctrl->data->get_bias_val(param);
> +			if (ret < 0)
> +				return ret;
> +
> +			rzg2l_rmw_pin_config(pctrl, PUPD(off), bit, PUPD_MASK, ret);
> +			break;
> +		}
> +
>  		case PIN_CONFIG_DRIVE_STRENGTH:
>  			arg = pinconf_to_config_argument(_configs[i]);
>  
> @@ -2746,6 +2815,8 @@ static struct rzg2l_pinctrl_data r9a07g044_data = {
>  	.pmc_writeb = &rzg2l_pmc_writeb,
>  	.read_oen = &rzg2l_read_oen,
>  	.write_oen = &rzg2l_write_oen,
> +	.get_bias_param = &rzg2l_get_bias_param,
> +	.get_bias_val = &rzg2l_get_bias_val,
>  };
>  
>  static struct rzg2l_pinctrl_data r9a08g045_data = {
> @@ -2761,6 +2832,8 @@ static struct rzg2l_pinctrl_data r9a08g045_data = {
>  	.pmc_writeb = &rzg2l_pmc_writeb,
>  	.read_oen = &rzg2l_read_oen,
>  	.write_oen = &rzg2l_write_oen,
> +	.get_bias_param = &rzg2l_get_bias_param,
> +	.get_bias_val = &rzg2l_get_bias_val,
>  };
>  
>  static const struct of_device_id rzg2l_pinctrl_of_table[] = {
Lad, Prabhakar May 30, 2024, 10:15 a.m. UTC | #6 
Hi Claudiu,

Thank you for the review.

On Thu, May 30, 2024 at 8:48 AM claudiu beznea <claudiu.beznea@tuxon.dev> wrote:
>
> Hi, Prabhakar,
>
> On 23.04.2024 20:58, Prabhakar wrote:
> > From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> >
> > Add support to configure bias-disable, bias-pull-up and bias-pull-down
> > properties of the pin.
> >
> > Two new function pointers get_bias_param() and get_bias_val() are
> > introduced as the values in PUPD register differ when compared to
> > RZ/G2L family and RZ/V2H(P) SoC,
> >
> > Value | RZ/G2L        | RZ/V2H
> > ---------------------------------
> > 00b:  | Bias Disabled | Pull up/down disabled
> > 01b:  | Pull-up       | Pull up/down disabled
> > 10b:  | Pull-down     | Pull-down
> > 11b:  | Prohibited    | Pull-up
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > ---
> > RFC->v2
> > - New patch
> > ---
> >  drivers/pinctrl/renesas/pinctrl-rzg2l.c | 73 +++++++++++++++++++++++++
> >  1 file changed, 73 insertions(+)
> >
> > diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > index 102fa75c71d3..c144bf43522b 100644
> > --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > @@ -122,6 +122,7 @@
> >  #define IOLH(off)            (0x1000 + (off) * 8)
> >  #define SR(off)                      (0x1400 + (off) * 8)
> >  #define IEN(off)             (0x1800 + (off) * 8)
> > +#define PUPD(off)            (0x1C00 + (off) * 8)
> >  #define ISEL(off)            (0x2C00 + (off) * 8)
> >  #define SD_CH(off, ch)               ((off) + (ch) * 4)
> >  #define ETH_POC(off, ch)     ((off) + (ch) * 4)
> > @@ -140,6 +141,7 @@
> >  #define IEN_MASK             0x01
> >  #define IOLH_MASK            0x03
> >  #define SR_MASK                      0x01
> > +#define PUPD_MASK            0x03
> >
> >  #define PM_INPUT             0x1
> >  #define PM_OUTPUT            0x2
> > @@ -265,6 +267,8 @@ struct rzg2l_pinctrl_data {
> >       void (*pmc_writeb)(struct rzg2l_pinctrl *pctrl, u8 val, void __iomem *addr);
> >       u32 (*read_oen)(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8 pin);
> >       int (*write_oen)(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8 pin, u8 oen);
> > +     int (*get_bias_param)(u8 val);
> > +     int (*get_bias_val)(enum pin_config_param param);
> >  };
> >
> >  /**
> > @@ -1081,6 +1085,38 @@ static int rzg2l_write_oen(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8
> >       return 0;
> >  }
> >
> > +static int rzg2l_get_bias_param(u8 val)
> > +{
> > +     switch (val) {
> > +     case 0:
> > +             return PIN_CONFIG_BIAS_DISABLE;
> > +     case 1:
> > +             return PIN_CONFIG_BIAS_PULL_UP;
> > +     case 2:
> > +             return PIN_CONFIG_BIAS_PULL_DOWN;
> > +     default:
> > +             break;
> > +     }
> > +
> > +     return -EINVAL;
> > +}
> > +
> > +static int rzg2l_get_bias_val(enum pin_config_param param)
> > +{
> > +     switch (param) {
> > +     case PIN_CONFIG_BIAS_DISABLE:
> > +             return 0;
> > +     case PIN_CONFIG_BIAS_PULL_UP:
> > +             return 1;
> > +     case PIN_CONFIG_BIAS_PULL_DOWN:
> > +             return 2;
> > +     default:
> > +             break;
> > +     }
> > +
> > +     return -EINVAL;
> > +}
> > +
> >  static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
> >                                    unsigned int _pin,
> >                                    unsigned long *config)
> > @@ -1139,6 +1175,25 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
> >               arg = rzg2l_read_pin_config(pctrl, SR(off), bit, SR_MASK);
> >               break;
> >
> > +     case PIN_CONFIG_BIAS_DISABLE:
> > +     case PIN_CONFIG_BIAS_PULL_UP:
> > +     case PIN_CONFIG_BIAS_PULL_DOWN: {
>
> Block { } can be removed here.
>
Agreed, I will drop it.

> > +             if (!(cfg & PIN_CFG_PUPD))
> > +                     return -EINVAL;
> > +
> > +             ret = pctrl->data->get_bias_param(rzg2l_read_pin_config(pctrl,
> > +                                                                     PUPD(off),
> > +                                                                     bit, PUPD_MASK));
> > +             if (ret < 0)
> > +                     return ret;
> > +
> > +             if (ret != param)
> > +                     return -EINVAL;
>
> Can this happen? Otherwise it can be removed.
>
> > +             /* for PIN_CONFIG_BIAS_PULL_UP/DOWN when enabled we just return 1 */
>
> What about bias disable? I haven't checked in detail, is it OK to do
> arg = 1 here?
>
For BIAS_DISABLE config there isn't any argument, hence the above
comment mentions only for UP/DOWN. Passing arg = 1 for BIAS_DISABLE
has no effect.

> > +             arg = 1;
> > +             break;
> > +     }
> > +
> >       case PIN_CONFIG_DRIVE_STRENGTH: {
> >               unsigned int index;
> >
> > @@ -1254,6 +1309,20 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
> >                       rzg2l_rmw_pin_config(pctrl, SR(off), bit, SR_MASK, arg);
> >                       break;
> >
> > +             case PIN_CONFIG_BIAS_DISABLE:
> > +             case PIN_CONFIG_BIAS_PULL_UP:
> > +             case PIN_CONFIG_BIAS_PULL_DOWN: {
>
> Block { } can be removed in this case.
>
Agreed, I will drop it.

Cheers,
Prabhakar
Lad, Prabhakar May 30, 2024, 10:37 a.m. UTC | #7 
On Thu, May 30, 2024 at 8:48 AM claudiu beznea <claudiu.beznea@tuxon.dev> wrote:
>
> Hi, Prabhakar,
>
> On 23.04.2024 20:58, Prabhakar wrote:
> > From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> >
> > Add support to configure bias-disable, bias-pull-up and bias-pull-down
> > properties of the pin.
> >
> > Two new function pointers get_bias_param() and get_bias_val() are
> > introduced as the values in PUPD register differ when compared to
> > RZ/G2L family and RZ/V2H(P) SoC,
> >
> > Value | RZ/G2L        | RZ/V2H
> > ---------------------------------
> > 00b:  | Bias Disabled | Pull up/down disabled
> > 01b:  | Pull-up       | Pull up/down disabled
> > 10b:  | Pull-down     | Pull-down
> > 11b:  | Prohibited    | Pull-up
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > ---
> > RFC->v2
> > - New patch
> > ---
> >  drivers/pinctrl/renesas/pinctrl-rzg2l.c | 73 +++++++++++++++++++++++++
> >  1 file changed, 73 insertions(+)
> >
> > diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > index 102fa75c71d3..c144bf43522b 100644
> > --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > @@ -122,6 +122,7 @@
> >  #define IOLH(off)            (0x1000 + (off) * 8)
> >  #define SR(off)                      (0x1400 + (off) * 8)
> >  #define IEN(off)             (0x1800 + (off) * 8)
> > +#define PUPD(off)            (0x1C00 + (off) * 8)
> >  #define ISEL(off)            (0x2C00 + (off) * 8)
> >  #define SD_CH(off, ch)               ((off) + (ch) * 4)
> >  #define ETH_POC(off, ch)     ((off) + (ch) * 4)
> > @@ -140,6 +141,7 @@
> >  #define IEN_MASK             0x01
> >  #define IOLH_MASK            0x03
> >  #define SR_MASK                      0x01
> > +#define PUPD_MASK            0x03
> >
> >  #define PM_INPUT             0x1
> >  #define PM_OUTPUT            0x2
> > @@ -265,6 +267,8 @@ struct rzg2l_pinctrl_data {
> >       void (*pmc_writeb)(struct rzg2l_pinctrl *pctrl, u8 val, void __iomem *addr);
> >       u32 (*read_oen)(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8 pin);
> >       int (*write_oen)(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8 pin, u8 oen);
> > +     int (*get_bias_param)(u8 val);
> > +     int (*get_bias_val)(enum pin_config_param param);
> >  };
> >
> >  /**
> > @@ -1081,6 +1085,38 @@ static int rzg2l_write_oen(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8
> >       return 0;
> >  }
> >
> > +static int rzg2l_get_bias_param(u8 val)
> > +{
> > +     switch (val) {
> > +     case 0:
> > +             return PIN_CONFIG_BIAS_DISABLE;
> > +     case 1:
> > +             return PIN_CONFIG_BIAS_PULL_UP;
> > +     case 2:
> > +             return PIN_CONFIG_BIAS_PULL_DOWN;
> > +     default:
> > +             break;
> > +     }
> > +
> > +     return -EINVAL;
> > +}
> > +
> > +static int rzg2l_get_bias_val(enum pin_config_param param)
> > +{
> > +     switch (param) {
> > +     case PIN_CONFIG_BIAS_DISABLE:
> > +             return 0;
> > +     case PIN_CONFIG_BIAS_PULL_UP:
> > +             return 1;
> > +     case PIN_CONFIG_BIAS_PULL_DOWN:
> > +             return 2;
> > +     default:
> > +             break;
> > +     }
> > +
> > +     return -EINVAL;
> > +}
> > +
> >  static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
> >                                    unsigned int _pin,
> >                                    unsigned long *config)
> > @@ -1139,6 +1175,25 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
> >               arg = rzg2l_read_pin_config(pctrl, SR(off), bit, SR_MASK);
> >               break;
> >
> > +     case PIN_CONFIG_BIAS_DISABLE:
> > +     case PIN_CONFIG_BIAS_PULL_UP:
> > +     case PIN_CONFIG_BIAS_PULL_DOWN: {
>
> Block { } can be removed here.
>
> > +             if (!(cfg & PIN_CFG_PUPD))
> > +                     return -EINVAL;
> > +
> > +             ret = pctrl->data->get_bias_param(rzg2l_read_pin_config(pctrl,
> > +                                                                     PUPD(off),
> > +                                                                     bit, PUPD_MASK));
> > +             if (ret < 0)
> > +                     return ret;
> > +
> > +             if (ret != param)
> > +                     return -EINVAL;
>
> Can this happen? Otherwise it can be removed.
>
Yes this can happen (and is needed) as we want to report only the
current BIAS setting of the pin.

For example without this condition I get the below for ET1_RXD3 pin:
pin 173 (ET1_RXD3): input bias disabled, input bias pull down (0x1
ohms), input bias pull up (0x1 ohms)
with the check included:
pin 173 (ET1_RXD3): input bias disabled

Cheers,
Prabhakar
diff mbox series

Patch

diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
index 102fa75c71d3..c144bf43522b 100644
--- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
+++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
@@ -122,6 +122,7 @@ 
 #define IOLH(off)		(0x1000 + (off) * 8)
 #define SR(off)			(0x1400 + (off) * 8)
 #define IEN(off)		(0x1800 + (off) * 8)
+#define PUPD(off)		(0x1C00 + (off) * 8)
 #define ISEL(off)		(0x2C00 + (off) * 8)
 #define SD_CH(off, ch)		((off) + (ch) * 4)
 #define ETH_POC(off, ch)	((off) + (ch) * 4)
@@ -140,6 +141,7 @@ 
 #define IEN_MASK		0x01
 #define IOLH_MASK		0x03
 #define SR_MASK			0x01
+#define PUPD_MASK		0x03
 
 #define PM_INPUT		0x1
 #define PM_OUTPUT		0x2
@@ -265,6 +267,8 @@  struct rzg2l_pinctrl_data {
 	void (*pmc_writeb)(struct rzg2l_pinctrl *pctrl, u8 val, void __iomem *addr);
 	u32 (*read_oen)(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8 pin);
 	int (*write_oen)(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8 pin, u8 oen);
+	int (*get_bias_param)(u8 val);
+	int (*get_bias_val)(enum pin_config_param param);
 };
 
 /**
@@ -1081,6 +1085,38 @@  static int rzg2l_write_oen(struct rzg2l_pinctrl *pctrl, u32 caps, u32 offset, u8
 	return 0;
 }
 
+static int rzg2l_get_bias_param(u8 val)
+{
+	switch (val) {
+	case 0:
+		return PIN_CONFIG_BIAS_DISABLE;
+	case 1:
+		return PIN_CONFIG_BIAS_PULL_UP;
+	case 2:
+		return PIN_CONFIG_BIAS_PULL_DOWN;
+	default:
+		break;
+	}
+
+	return -EINVAL;
+}
+
+static int rzg2l_get_bias_val(enum pin_config_param param)
+{
+	switch (param) {
+	case PIN_CONFIG_BIAS_DISABLE:
+		return 0;
+	case PIN_CONFIG_BIAS_PULL_UP:
+		return 1;
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		return 2;
+	default:
+		break;
+	}
+
+	return -EINVAL;
+}
+
 static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 				     unsigned int _pin,
 				     unsigned long *config)
@@ -1139,6 +1175,25 @@  static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 		arg = rzg2l_read_pin_config(pctrl, SR(off), bit, SR_MASK);
 		break;
 
+	case PIN_CONFIG_BIAS_DISABLE:
+	case PIN_CONFIG_BIAS_PULL_UP:
+	case PIN_CONFIG_BIAS_PULL_DOWN: {
+		if (!(cfg & PIN_CFG_PUPD))
+			return -EINVAL;
+
+		ret = pctrl->data->get_bias_param(rzg2l_read_pin_config(pctrl,
+									PUPD(off),
+									bit, PUPD_MASK));
+		if (ret < 0)
+			return ret;
+
+		if (ret != param)
+			return -EINVAL;
+		/* for PIN_CONFIG_BIAS_PULL_UP/DOWN when enabled we just return 1 */
+		arg = 1;
+		break;
+	}
+
 	case PIN_CONFIG_DRIVE_STRENGTH: {
 		unsigned int index;
 
@@ -1254,6 +1309,20 @@  static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 			rzg2l_rmw_pin_config(pctrl, SR(off), bit, SR_MASK, arg);
 			break;
 
+		case PIN_CONFIG_BIAS_DISABLE:
+		case PIN_CONFIG_BIAS_PULL_UP:
+		case PIN_CONFIG_BIAS_PULL_DOWN: {
+			if (!(cfg & PIN_CFG_PUPD))
+				return -EINVAL;
+
+			ret = pctrl->data->get_bias_val(param);
+			if (ret < 0)
+				return ret;
+
+			rzg2l_rmw_pin_config(pctrl, PUPD(off), bit, PUPD_MASK, ret);
+			break;
+		}
+
 		case PIN_CONFIG_DRIVE_STRENGTH:
 			arg = pinconf_to_config_argument(_configs[i]);
 
@@ -2746,6 +2815,8 @@  static struct rzg2l_pinctrl_data r9a07g044_data = {
 	.pmc_writeb = &rzg2l_pmc_writeb,
 	.read_oen = &rzg2l_read_oen,
 	.write_oen = &rzg2l_write_oen,
+	.get_bias_param = &rzg2l_get_bias_param,
+	.get_bias_val = &rzg2l_get_bias_val,
 };
 
 static struct rzg2l_pinctrl_data r9a08g045_data = {
@@ -2761,6 +2832,8 @@  static struct rzg2l_pinctrl_data r9a08g045_data = {
 	.pmc_writeb = &rzg2l_pmc_writeb,
 	.read_oen = &rzg2l_read_oen,
 	.write_oen = &rzg2l_write_oen,
+	.get_bias_param = &rzg2l_get_bias_param,
+	.get_bias_val = &rzg2l_get_bias_val,
 };
 
 static const struct of_device_id rzg2l_pinctrl_of_table[] = {