Message ID | 20240729231259.2122976-3-quic_amelende@quicinc.com |
---|---|
State | New |
Headers | show |
Series | thermal: qcom-spmi-temp-alarm: add support for new TEMP_ALARM subtypes | expand |
On 30/07/2024 01:12, Anjelique Melendez wrote: > Add compatible "qcom,spmi-temp-alarm-lite" for Temp alarm lite > peripherals. Temp alarm lite peripherals have two stages: warning and > shutdown, and use a pair of registers to configure warning interrupt > threshold temperature and an automatic hardware shutdown threshold > temperature. > > When defining thermal zone trips for a temp alarm lite device the first > thermal zone trip is for warning alarm IRQ in HW, the second thermal > zone trip is purely for software to perform a controlled shutdown (no HW > support) and the third thermal zone trip is for automatic hardware > shutdown. > > Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com> > --- > .../thermal/qcom,spmi-temp-alarm.yaml | 44 +++++++++++++++++++ > 1 file changed, 44 insertions(+) > > diff --git a/Documentation/devicetree/bindings/thermal/qcom,spmi-temp-alarm.yaml b/Documentation/devicetree/bindings/thermal/qcom,spmi-temp-alarm.yaml > index f9af88d51c2d..bbf201cad16b 100644 > --- a/Documentation/devicetree/bindings/thermal/qcom,spmi-temp-alarm.yaml > +++ b/Documentation/devicetree/bindings/thermal/qcom,spmi-temp-alarm.yaml > @@ -22,6 +22,7 @@ properties: > enum: > - qcom,spmi-temp-alarm > - qcom,spmi-temp-alarm-gen2-rev2 > + - qcom,spmi-temp-alarm-lite Uhu, it's growing, now we have "lite". No, this is way too ambiguous. NAK. Use PMIC compatibles. > > reg: > maxItems: 1 > @@ -84,3 +85,46 @@ examples: > }; > }; > }; > + > + - | > + > + pmic { > + #address-cells = <1>; > + #size-cells = <0>; > + > + pm8550b_lite_tz: pm8550b-temp-alarm-lite@c00 { There is no difference in this example, drop. > + compatible = "qcom,spmi-temp-alarm-lite"; > + reg = <0xc00>; > + interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > + #thermal-sensor-cells = <0>; > + }; > + }; > + > + thermal-zones { > + pm8550b_lite_temp_alarm: pm8550blite-thermal { Drop as well. Best regards, Krzysztof
diff --git a/Documentation/devicetree/bindings/thermal/qcom,spmi-temp-alarm.yaml b/Documentation/devicetree/bindings/thermal/qcom,spmi-temp-alarm.yaml index f9af88d51c2d..bbf201cad16b 100644 --- a/Documentation/devicetree/bindings/thermal/qcom,spmi-temp-alarm.yaml +++ b/Documentation/devicetree/bindings/thermal/qcom,spmi-temp-alarm.yaml @@ -22,6 +22,7 @@ properties: enum: - qcom,spmi-temp-alarm - qcom,spmi-temp-alarm-gen2-rev2 + - qcom,spmi-temp-alarm-lite reg: maxItems: 1 @@ -84,3 +85,46 @@ examples: }; }; }; + + - | + + pmic { + #address-cells = <1>; + #size-cells = <0>; + + pm8550b_lite_tz: pm8550b-temp-alarm-lite@c00 { + compatible = "qcom,spmi-temp-alarm-lite"; + reg = <0xc00>; + interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + }; + + thermal-zones { + pm8550b_lite_temp_alarm: pm8550blite-thermal { + polling-delay-passive = <100>; + polling-delay = <0>; + thermal-sensors = <&pm8550b_lite_tz>; + + trips { + pm8550b_lite_trip0: trip0 { + temperature = <125000>; + hysteresis = <0>; + type = "passive"; + }; + + pm8550b_lite_trip1: trip1 { + temperature = <135000>; + hysteresis = <0>; + type = "passive"; + }; + + trip2 { + temperature = <145000>; + hysteresis = <0>; + type = "critical"; + }; + + }; + }; + };
Add compatible "qcom,spmi-temp-alarm-lite" for Temp alarm lite peripherals. Temp alarm lite peripherals have two stages: warning and shutdown, and use a pair of registers to configure warning interrupt threshold temperature and an automatic hardware shutdown threshold temperature. When defining thermal zone trips for a temp alarm lite device the first thermal zone trip is for warning alarm IRQ in HW, the second thermal zone trip is purely for software to perform a controlled shutdown (no HW support) and the third thermal zone trip is for automatic hardware shutdown. Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com> --- .../thermal/qcom,spmi-temp-alarm.yaml | 44 +++++++++++++++++++ 1 file changed, 44 insertions(+)