diff mbox series

[v2] power: sequencing: qcom-wcn: explain why we need the WLAN_EN GPIO hack

Message ID 20250102121530.26993-1-brgl@bgdev.pl
State New
Headers show
Series [v2] power: sequencing: qcom-wcn: explain why we need the WLAN_EN GPIO hack | expand

Commit Message

Bartosz Golaszewski Jan. 2, 2025, 12:15 p.m. UTC 
From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

With the recent rework of the PCI power control code, the workaround for
the wlan-enable GPIO - where we don't set a default (low) state in the
power sequencing driver, but instead request the pin as-is - should no
longer be needed but some platforms still fail to probe the WLAN
controller. This is caused by the Qcom PCIe controller and needs a
workaround in the controller driver so add a FIXME to eventually remove
the hack from this driver once this is done.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
Changes in v2:
- reword the FIXME comment as advised by Manivannan

 drivers/power/sequencing/pwrseq-qcom-wcn.c | 7 +++++++
 1 file changed, 7 insertions(+)

Comments

Bartosz Golaszewski Jan. 13, 2025, 8:14 a.m. UTC | #1 
From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>


On Thu, 02 Jan 2025 13:15:30 +0100, Bartosz Golaszewski wrote:
> With the recent rework of the PCI power control code, the workaround for
> the wlan-enable GPIO - where we don't set a default (low) state in the
> power sequencing driver, but instead request the pin as-is - should no
> longer be needed but some platforms still fail to probe the WLAN
> controller. This is caused by the Qcom PCIe controller and needs a
> workaround in the controller driver so add a FIXME to eventually remove
> the hack from this driver once this is done.
> 
> [...]

Applied, thanks!

[1/1] power: sequencing: qcom-wcn: explain why we need the WLAN_EN GPIO hack
      commit: 29da3e8748f97dcf01498b00d42a3e7574ece80b

Best regards,
diff mbox series

Patch

diff --git a/drivers/power/sequencing/pwrseq-qcom-wcn.c b/drivers/power/sequencing/pwrseq-qcom-wcn.c
index cc03b5aaa8f2..e8f5030f2639 100644
--- a/drivers/power/sequencing/pwrseq-qcom-wcn.c
+++ b/drivers/power/sequencing/pwrseq-qcom-wcn.c
@@ -396,6 +396,13 @@  static int pwrseq_qcom_wcn_probe(struct platform_device *pdev)
 		return dev_err_probe(dev, PTR_ERR(ctx->bt_gpio),
 				     "Failed to get the Bluetooth enable GPIO\n");
 
+	/*
+	 * FIXME: This should actually be GPIOD_OUT_LOW, but doing so would
+	 * cause the WLAN power to be toggled, resulting in PCIe link down.
+	 * Since the PCIe controller driver is not handling link down currently,
+	 * the device becomes unusable. So we need to keep this workaround until
+	 * the link down handling is implemented in the controller driver.
+	 */
 	ctx->wlan_gpio = devm_gpiod_get_optional(dev, "wlan-enable",
 						 GPIOD_ASIS);
 	if (IS_ERR(ctx->wlan_gpio))