diff mbox series

[RFC,v2,6/6] pinctrl: Add pin controller driver for AAEON UP boards

Message ID 20250317-aaeon-up-board-pinctrl-support-v2-6-36126e30aa62@bootlin.com
State Superseded
Headers show
Series Add pinctrl support for the AAEON UP board FPGA | expand

Commit Message

Thomas Richard March 17, 2025, 3:38 p.m. UTC 
This enables the pin control support of the onboard FPGA on AAEON UP
boards.

This FPGA acts as a level shifter between the Intel SoC pins and the pin
header, and also as a mux or switch.

+---------+          +--------------+             +---+
          |          |              |             |   |
          | PWM0     |       \      |             | H |
          |----------|------  \-----|-------------| E |
          | I2C0_SDA |              |             | A |
Intel SoC |----------|------\       |             | D |
          | GPIO0    |       \------|-------------| E |
          |----------|------        |             | R |
          |          |     FPGA     |             |   |
----------+          +--------------+             +---+

For most of the pins, the FPGA opens/closes a switch to enable/disable
the access to the SoC pin from a pin header.
Each switch, has a direction flag that is set depending the status of the
SoC pin.

For some other pins, the FPGA acts as a mux, and routes one pin (or the
other one) to the header.

The driver provides also a gpiochip. It requests SoC pins in GPIO mode,
and drives them in tandem with FPGA pins (switch/mux direction).

UP boards and UP Squared boards are supported.

Based on the work done by Gary Wang <garywang@aaeon.com.tw>, largely
rewritten.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
---
 drivers/pinctrl/Kconfig           |   15 +
 drivers/pinctrl/Makefile          |    1 +
 drivers/pinctrl/pinctrl-upboard.c | 1094 +++++++++++++++++++++++++++++++++++++
 3 files changed, 1110 insertions(+)

Comments

Thomas Richard April 9, 2025, 2:02 p.m. UTC | #1 
On 3/17/25 19:42, Andy Shevchenko wrote:
>> +	board_id = (enum upboard_board_id)dmi_id->driver_data;
>> +
>> +	switch (board_id) {
>> +	case BOARD_UP_APL01:
>> +		pctrl->maps = upboard_pinctrl_mapping_up_apl01;
>> +		pctrl->nmaps = ARRAY_SIZE(upboard_pinctrl_mapping_up_apl01);
>> +		break;
> 
> Hmm... This is strange. Seems it has only Apollo Lake in the name while
> the above states that there is UP board support (which is Cherry Trail based).

There is pinctrl code for UP and UP Squared. But I only added mapping
for UP Squared board because it was the easiest board to add (all needed
pinctrl groups and functions are already defined in the Intel pinctrl
driver).
I wanted to focus on the driver itself and the forwarder library, and
send later an other series to add UP board support (with the
corresponding functions/groups in the Intel pinctrl driver).

So yes UP board pinctrl part is unused for now, but everything is ready
to add support for UP board in the future.

Otherwise I can remove UP part if you prefer.

Regards,

Thomas
Thomas Richard April 15, 2025, 8:39 a.m. UTC | #2 
On 4/9/25 16:02, Thomas Richard wrote:
> On 3/17/25 19:42, Andy Shevchenko wrote:
>>> +	board_id = (enum upboard_board_id)dmi_id->driver_data;
>>> +
>>> +	switch (board_id) {
>>> +	case BOARD_UP_APL01:
>>> +		pctrl->maps = upboard_pinctrl_mapping_up_apl01;
>>> +		pctrl->nmaps = ARRAY_SIZE(upboard_pinctrl_mapping_up_apl01);
>>> +		break;
>>
>> Hmm... This is strange. Seems it has only Apollo Lake in the name while
>> the above states that there is UP board support (which is Cherry Trail based).
> 
> There is pinctrl code for UP and UP Squared. But I only added mapping
> for UP Squared board because it was the easiest board to add (all needed
> pinctrl groups and functions are already defined in the Intel pinctrl
> driver).
> I wanted to focus on the driver itself and the forwarder library, and
> send later an other series to add UP board support (with the
> corresponding functions/groups in the Intel pinctrl driver).
> 
> So yes UP board pinctrl part is unused for now, but everything is ready
> to add support for UP board in the future.
> 
> Otherwise I can remove UP part if you prefer.

Hi Andy,

I just realized that my wording was incorrect, so let me clarify.

The UP Board [1] (based on Cherry Trail) is not supported at all (its
FPGA is not supported by the MFD driver), and there is no plan to
support it.

The "up" code (for example upboard_up_pinctrl_data) is for most boards
of the UP family (UP 7000, UPXi12, UP Squared Pro 7000 ...) but not the
UP Board [1]. Indeed for now there is no pinctrl mapping for these boards.

The "up2" code is for the UP Squared board which uses a different FPGA.

As I explained I only added pinctrl mapping for the UP Squared board, as
it was the easiest one (no need to add groups/functions in Intel pinctrl
driver). But the plan is to add support for other boards (UP 7000,
IPXi12 ...) later.

Regarding the name of the pinctrl mapping for UP Squared board, it is
indeed a bit confusing, I will rename it.

[1]
https://www.aaeon.com/en/product/detail/up-board-computer-board-for-professional-makers

Best Regards,

Thomas
diff mbox series

Patch

diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 95a8e2b9a614a..856152363e3a6 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -576,6 +576,21 @@  config PINCTRL_TH1520
 	  This driver is needed for RISC-V development boards like
 	  the BeagleV Ahead and the LicheePi 4A.
 
+config PINCTRL_UPBOARD
+	tristate "AAeon UP board FPGA pin controller"
+	depends on MFD_UPBOARD_FPGA
+	select PINMUX
+	select GENERIC_PINCTRL_GROUPS
+	select GENERIC_PINMUX_FUNCTIONS
+	select GPIO_AGGREGATOR
+	help
+	  Pin controller for the FPGA GPIO lines on UP boards. Due to the
+	  hardware layout, the driver control the FPGA pins in tandem with
+	  their corresponding Intel SoC GPIOs.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called pinctrl-upboard.
+
 config PINCTRL_ZYNQ
 	bool "Pinctrl driver for Xilinx Zynq"
 	depends on ARCH_ZYNQ
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index fba1c56624c0d..989b8d28ecac3 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -56,6 +56,7 @@  obj-$(CONFIG_PINCTRL_SX150X)	+= pinctrl-sx150x.o
 obj-$(CONFIG_PINCTRL_TB10X)	+= pinctrl-tb10x.o
 obj-$(CONFIG_PINCTRL_TPS6594)	+= pinctrl-tps6594.o
 obj-$(CONFIG_PINCTRL_TH1520)	+= pinctrl-th1520.o
+obj-$(CONFIG_PINCTRL_UPBOARD)	+= pinctrl-upboard.o
 obj-$(CONFIG_PINCTRL_ZYNQMP)	+= pinctrl-zynqmp.o
 obj-$(CONFIG_PINCTRL_ZYNQ)	+= pinctrl-zynq.o
 
diff --git a/drivers/pinctrl/pinctrl-upboard.c b/drivers/pinctrl/pinctrl-upboard.c
new file mode 100644
index 0000000000000..9f7d0c6b707d0
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-upboard.c
@@ -0,0 +1,1094 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * UP board pin control driver.
+ *
+ * FPGA provides more GPIO driving power, LEDS and pin mux function.
+ *
+ * Copyright (c) AAEON. All rights reserved.
+ * Copyright (C) 2024 Bootlin
+ *
+ * Author: Gary Wang <garywang@aaeon.com.tw>
+ * Author: Thomas Richard <thomas.richard@bootlin.com>
+ */
+
+#include <linux/device.h>
+#include <linux/dmi.h>
+#include <linux/gpio/consumer.h>
+#include <linux/gpio/driver.h>
+#include <linux/gpio/gpio-fwd.h>
+#include <linux/mfd/upboard-fpga.h>
+#include <linux/module.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/seq_file.h>
+
+#include "core.h"
+#include "pinmux.h"
+
+enum upboard_board_id {
+	BOARD_UP_APL01,
+};
+
+enum upboard_pin_mode {
+	UPBOARD_PIN_MODE_FUNCTION = 1,
+	UPBOARD_PIN_MODE_GPIO_IN,
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_DISABLED,
+};
+
+struct upboard_pin {
+	struct regmap_field *funcbit;
+	struct regmap_field *enbit;
+	struct regmap_field *dirbit;
+};
+
+struct upboard_pingroup {
+	struct pingroup grp;
+	enum upboard_pin_mode mode;
+	const enum upboard_pin_mode *modes;
+};
+
+struct upboard_pinctrl_data {
+	const struct upboard_pingroup *groups;
+	size_t ngroups;
+	const struct pinfunction *funcs;
+	size_t nfuncs;
+	const unsigned int *pin_header;
+	size_t ngpio;
+};
+
+struct upboard_pinctrl {
+	struct gpio_chip chip;
+	struct device *dev;
+	struct pinctrl_dev *pctldev;
+	const struct upboard_pinctrl_data *pctrl_data;
+	struct gpio_pin_range pin_range;
+	struct upboard_pin *pins;
+	const struct pinctrl_map *maps;
+	size_t nmaps;
+};
+
+enum upboard_func0_fpgabit {
+	UPBOARD_FUNC_I2C0_EN = 8,
+	UPBOARD_FUNC_I2C1_EN = 9,
+	UPBOARD_FUNC_CEC0_EN = 12,
+	UPBOARD_FUNC_ADC0_EN = 14,
+};
+
+static const struct reg_field upboard_i2c0_reg =
+	REG_FIELD(UPBOARD_REG_FUNC_EN0, UPBOARD_FUNC_I2C0_EN, UPBOARD_FUNC_I2C0_EN);
+
+static const struct reg_field upboard_i2c1_reg =
+	REG_FIELD(UPBOARD_REG_FUNC_EN0, UPBOARD_FUNC_I2C1_EN, UPBOARD_FUNC_I2C1_EN);
+
+static const struct reg_field upboard_adc0_reg =
+	REG_FIELD(UPBOARD_REG_FUNC_EN0, UPBOARD_FUNC_ADC0_EN, UPBOARD_FUNC_ADC0_EN);
+
+#define UPBOARD_UP_BIT_TO_PIN(bit) UPBOARD_UP_BIT_##bit
+
+#define UPBOARD_UP_PIN_NAME(id)					\
+	{							\
+		.number = UPBOARD_UP_BIT_##id,			\
+		.name = #id,					\
+	}
+
+#define UPBOARD_UP_PIN_MUX(bit, data)				\
+	{							\
+		.number = UPBOARD_UP_BIT_##bit,			\
+		.name = "PINMUX_"#bit,				\
+		.drv_data = (void *)(data),			\
+	}
+
+#define UPBOARD_UP_PIN_FUNC(id, data)				\
+	{							\
+		.number = UPBOARD_UP_BIT_##id,			\
+		.name = #id,					\
+		.drv_data = (void *)(data),			\
+	}
+
+enum upboard_up_fpgabit {
+	UPBOARD_UP_BIT_I2C1_SDA,
+	UPBOARD_UP_BIT_I2C1_SCL,
+	UPBOARD_UP_BIT_ADC0,
+	UPBOARD_UP_BIT_UART1_RTS,
+	UPBOARD_UP_BIT_GPIO27,
+	UPBOARD_UP_BIT_GPIO22,
+	UPBOARD_UP_BIT_SPI_MOSI,
+	UPBOARD_UP_BIT_SPI_MISO,
+	UPBOARD_UP_BIT_SPI_CLK,
+	UPBOARD_UP_BIT_I2C0_SDA,
+	UPBOARD_UP_BIT_GPIO5,
+	UPBOARD_UP_BIT_GPIO6,
+	UPBOARD_UP_BIT_PWM1,
+	UPBOARD_UP_BIT_I2S_FRM,
+	UPBOARD_UP_BIT_GPIO26,
+	UPBOARD_UP_BIT_UART1_TX,
+	UPBOARD_UP_BIT_UART1_RX,
+	UPBOARD_UP_BIT_I2S_CLK,
+	UPBOARD_UP_BIT_GPIO23,
+	UPBOARD_UP_BIT_GPIO24,
+	UPBOARD_UP_BIT_GPIO25,
+	UPBOARD_UP_BIT_SPI_CS0,
+	UPBOARD_UP_BIT_SPI_CS1,
+	UPBOARD_UP_BIT_I2C0_SCL,
+	UPBOARD_UP_BIT_PWM0,
+	UPBOARD_UP_BIT_UART1_CTS,
+	UPBOARD_UP_BIT_I2S_DIN,
+	UPBOARD_UP_BIT_I2S_DOUT,
+};
+
+static const struct pinctrl_pin_desc upboard_up_pins[] = {
+	UPBOARD_UP_PIN_FUNC(I2C1_SDA, &upboard_i2c1_reg),
+	UPBOARD_UP_PIN_FUNC(I2C1_SCL, &upboard_i2c1_reg),
+	UPBOARD_UP_PIN_FUNC(ADC0, &upboard_adc0_reg),
+	UPBOARD_UP_PIN_NAME(UART1_RTS),
+	UPBOARD_UP_PIN_NAME(GPIO27),
+	UPBOARD_UP_PIN_NAME(GPIO22),
+	UPBOARD_UP_PIN_NAME(SPI_MOSI),
+	UPBOARD_UP_PIN_NAME(SPI_MISO),
+	UPBOARD_UP_PIN_NAME(SPI_CLK),
+	UPBOARD_UP_PIN_FUNC(I2C0_SDA, &upboard_i2c0_reg),
+	UPBOARD_UP_PIN_NAME(GPIO5),
+	UPBOARD_UP_PIN_NAME(GPIO6),
+	UPBOARD_UP_PIN_NAME(PWM1),
+	UPBOARD_UP_PIN_NAME(I2S_FRM),
+	UPBOARD_UP_PIN_NAME(GPIO26),
+	UPBOARD_UP_PIN_NAME(UART1_TX),
+	UPBOARD_UP_PIN_NAME(UART1_RX),
+	UPBOARD_UP_PIN_NAME(I2S_CLK),
+	UPBOARD_UP_PIN_NAME(GPIO23),
+	UPBOARD_UP_PIN_NAME(GPIO24),
+	UPBOARD_UP_PIN_NAME(GPIO25),
+	UPBOARD_UP_PIN_NAME(SPI_CS0),
+	UPBOARD_UP_PIN_NAME(SPI_CS1),
+	UPBOARD_UP_PIN_FUNC(I2C0_SCL, &upboard_i2c0_reg),
+	UPBOARD_UP_PIN_NAME(PWM0),
+	UPBOARD_UP_PIN_NAME(UART1_CTS),
+	UPBOARD_UP_PIN_NAME(I2S_DIN),
+	UPBOARD_UP_PIN_NAME(I2S_DOUT),
+};
+
+static const unsigned int upboard_up_pin_header[] = {
+	UPBOARD_UP_BIT_TO_PIN(I2C0_SDA),
+	UPBOARD_UP_BIT_TO_PIN(I2C0_SCL),
+	UPBOARD_UP_BIT_TO_PIN(I2C1_SDA),
+	UPBOARD_UP_BIT_TO_PIN(I2C1_SCL),
+	UPBOARD_UP_BIT_TO_PIN(ADC0),
+	UPBOARD_UP_BIT_TO_PIN(GPIO5),
+	UPBOARD_UP_BIT_TO_PIN(GPIO6),
+	UPBOARD_UP_BIT_TO_PIN(SPI_CS1),
+	UPBOARD_UP_BIT_TO_PIN(SPI_CS0),
+	UPBOARD_UP_BIT_TO_PIN(SPI_MISO),
+	UPBOARD_UP_BIT_TO_PIN(SPI_MOSI),
+	UPBOARD_UP_BIT_TO_PIN(SPI_CLK),
+	UPBOARD_UP_BIT_TO_PIN(PWM0),
+	UPBOARD_UP_BIT_TO_PIN(PWM1),
+	UPBOARD_UP_BIT_TO_PIN(UART1_TX),
+	UPBOARD_UP_BIT_TO_PIN(UART1_RX),
+	UPBOARD_UP_BIT_TO_PIN(UART1_CTS),
+	UPBOARD_UP_BIT_TO_PIN(UART1_RTS),
+	UPBOARD_UP_BIT_TO_PIN(I2S_CLK),
+	UPBOARD_UP_BIT_TO_PIN(I2S_FRM),
+	UPBOARD_UP_BIT_TO_PIN(I2S_DIN),
+	UPBOARD_UP_BIT_TO_PIN(I2S_DOUT),
+	UPBOARD_UP_BIT_TO_PIN(GPIO22),
+	UPBOARD_UP_BIT_TO_PIN(GPIO23),
+	UPBOARD_UP_BIT_TO_PIN(GPIO24),
+	UPBOARD_UP_BIT_TO_PIN(GPIO25),
+	UPBOARD_UP_BIT_TO_PIN(GPIO26),
+	UPBOARD_UP_BIT_TO_PIN(GPIO27),
+};
+
+static const unsigned int upboard_up_uart1_pins[] = {
+	UPBOARD_UP_BIT_TO_PIN(UART1_TX),
+	UPBOARD_UP_BIT_TO_PIN(UART1_RX),
+	UPBOARD_UP_BIT_TO_PIN(UART1_RTS),
+	UPBOARD_UP_BIT_TO_PIN(UART1_CTS),
+};
+
+static const enum upboard_pin_mode upboard_up_uart1_modes[] = {
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_IN,
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_IN,
+};
+
+static_assert(ARRAY_SIZE(upboard_up_uart1_modes) ==
+	      ARRAY_SIZE(upboard_up_uart1_pins));
+
+static const unsigned int upboard_up_i2c0_pins[] = {
+	UPBOARD_UP_BIT_TO_PIN(I2C0_SCL),
+	UPBOARD_UP_BIT_TO_PIN(I2C0_SDA),
+};
+
+static const unsigned int upboard_up_i2c1_pins[] = {
+	UPBOARD_UP_BIT_TO_PIN(I2C1_SCL),
+	UPBOARD_UP_BIT_TO_PIN(I2C1_SDA),
+};
+
+static const unsigned int upboard_up_spi2_pins[] = {
+	UPBOARD_UP_BIT_TO_PIN(SPI_MOSI),
+	UPBOARD_UP_BIT_TO_PIN(SPI_MISO),
+	UPBOARD_UP_BIT_TO_PIN(SPI_CLK),
+	UPBOARD_UP_BIT_TO_PIN(SPI_CS0),
+	UPBOARD_UP_BIT_TO_PIN(SPI_CS1),
+};
+
+static const enum upboard_pin_mode upboard_up_spi2_modes[] = {
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_IN,
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_OUT,
+};
+
+static_assert(ARRAY_SIZE(upboard_up_spi2_modes) ==
+	      ARRAY_SIZE(upboard_up_spi2_pins));
+
+static const unsigned int upboard_up_i2s0_pins[]  = {
+	UPBOARD_UP_BIT_TO_PIN(I2S_FRM),
+	UPBOARD_UP_BIT_TO_PIN(I2S_CLK),
+	UPBOARD_UP_BIT_TO_PIN(I2S_DIN),
+	UPBOARD_UP_BIT_TO_PIN(I2S_DOUT),
+};
+
+static const enum upboard_pin_mode upboard_up_i2s0_modes[] = {
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_IN,
+	UPBOARD_PIN_MODE_GPIO_OUT,
+};
+
+static_assert(ARRAY_SIZE(upboard_up_i2s0_pins) ==
+	      ARRAY_SIZE(upboard_up_i2s0_modes));
+
+static const unsigned int upboard_up_pwm0_pins[] = {
+	UPBOARD_UP_BIT_TO_PIN(PWM0),
+};
+
+static const unsigned int upboard_up_pwm1_pins[] = {
+	UPBOARD_UP_BIT_TO_PIN(PWM1),
+};
+
+static const unsigned int upboard_up_adc0_pins[] = {
+	UPBOARD_UP_BIT_TO_PIN(ADC0),
+};
+
+#define UPBOARD_PINGROUP_MODE(_grp, _pins, _mode)			\
+{									\
+	.grp = PINCTRL_PINGROUP(_grp, _pins, ARRAY_SIZE(_pins)),	\
+	.mode = _mode,							\
+}
+
+#define UPBOARD_PINGROUP_MODES(_grp, _pins, _modes)			\
+{									\
+	.grp = PINCTRL_PINGROUP(_grp, _pins, ARRAY_SIZE(_pins)),	\
+	.modes = _modes,							\
+}
+
+static const struct upboard_pingroup upboard_up_pin_groups[] = {
+	UPBOARD_PINGROUP_MODES("uart1_grp", upboard_up_uart1_pins, upboard_up_uart1_modes),
+	UPBOARD_PINGROUP_MODE("i2c0_grp", upboard_up_i2c0_pins, UPBOARD_PIN_MODE_GPIO_OUT),
+	UPBOARD_PINGROUP_MODE("i2c1_grp", upboard_up_i2c1_pins, UPBOARD_PIN_MODE_GPIO_OUT),
+	UPBOARD_PINGROUP_MODES("spi2_grp", upboard_up_spi2_pins, &upboard_up_spi2_modes[0]),
+	UPBOARD_PINGROUP_MODES("i2s0_grp", upboard_up_i2s0_pins, &upboard_up_i2s0_modes[0]),
+	UPBOARD_PINGROUP_MODE("pwm0_grp", upboard_up_pwm0_pins, UPBOARD_PIN_MODE_GPIO_OUT),
+	UPBOARD_PINGROUP_MODE("pwm1_grp", upboard_up_pwm1_pins, UPBOARD_PIN_MODE_GPIO_OUT),
+	UPBOARD_PINGROUP_MODE("adc0_grp", upboard_up_adc0_pins, UPBOARD_PIN_MODE_GPIO_IN),
+};
+
+static const char * const upboard_up_uart1_groups[] = { "uart1_grp" };
+static const char * const upboard_up_i2c0_groups[]  = { "i2c0_grp" };
+static const char * const upboard_up_i2c1_groups[]  = { "i2c1_grp" };
+static const char * const upboard_up_spi2_groups[]  = { "spi2_grp" };
+static const char * const upboard_up_i2s0_groups[]  = { "i2s0_grp" };
+static const char * const upboard_up_pwm0_groups[]  = { "pwm0_grp" };
+static const char * const upboard_up_pwm1_groups[]  = { "pwm1_grp" };
+static const char * const upboard_up_adc0_groups[]  = { "adc0_grp" };
+
+#define UPBOARD_FUNCTION(func, groups)	PINCTRL_PINFUNCTION(func, groups, ARRAY_SIZE(groups))
+
+static const struct pinfunction upboard_up_pin_functions[] = {
+	UPBOARD_FUNCTION("uart1", upboard_up_uart1_groups),
+	UPBOARD_FUNCTION("i2c0", upboard_up_i2c0_groups),
+	UPBOARD_FUNCTION("i2c1", upboard_up_i2c1_groups),
+	UPBOARD_FUNCTION("spi2", upboard_up_spi2_groups),
+	UPBOARD_FUNCTION("i2s0", upboard_up_i2s0_groups),
+	UPBOARD_FUNCTION("pwm0", upboard_up_pwm0_groups),
+	UPBOARD_FUNCTION("pwm1", upboard_up_pwm1_groups),
+	UPBOARD_FUNCTION("adc0", upboard_up_adc0_groups),
+};
+
+static const struct upboard_pinctrl_data upboard_up_pinctrl_data = {
+	.groups = &upboard_up_pin_groups[0],
+	.ngroups = ARRAY_SIZE(upboard_up_pin_groups),
+	.funcs = &upboard_up_pin_functions[0],
+	.nfuncs = ARRAY_SIZE(upboard_up_pin_functions),
+	.pin_header = &upboard_up_pin_header[0],
+	.ngpio = ARRAY_SIZE(upboard_up_pin_header),
+};
+
+#define UPBOARD_UP2_BIT_TO_PIN(bit) UPBOARD_UP2_BIT_##bit
+
+#define UPBOARD_UP2_PIN_NAME(id)					\
+	{								\
+		.number = UPBOARD_UP2_BIT_##id,				\
+		.name = #id,						\
+	}
+
+#define UPBOARD_UP2_PIN_MUX(bit, data)					\
+	{								\
+		.number = UPBOARD_UP2_BIT_##bit,			\
+		.name = "PINMUX_"#bit,					\
+		.drv_data = (void *)(data),				\
+	}
+
+#define UPBOARD_UP2_PIN_FUNC(id, data)					\
+	{								\
+		.number = UPBOARD_UP2_BIT_##id,				\
+		.name = #id,						\
+		.drv_data = (void *)(data),				\
+	}
+
+enum upboard_up2_fpgabit {
+	UPBOARD_UP2_BIT_UART1_TXD,
+	UPBOARD_UP2_BIT_UART1_RXD,
+	UPBOARD_UP2_BIT_UART1_RTS,
+	UPBOARD_UP2_BIT_UART1_CTS,
+	UPBOARD_UP2_BIT_GPIO3_ADC0,
+	UPBOARD_UP2_BIT_GPIO5_ADC2,
+	UPBOARD_UP2_BIT_GPIO6_ADC3,
+	UPBOARD_UP2_BIT_GPIO11,
+	UPBOARD_UP2_BIT_EXHAT_LVDS1n,
+	UPBOARD_UP2_BIT_EXHAT_LVDS1p,
+	UPBOARD_UP2_BIT_SPI2_TXD,
+	UPBOARD_UP2_BIT_SPI2_RXD,
+	UPBOARD_UP2_BIT_SPI2_FS1,
+	UPBOARD_UP2_BIT_SPI2_FS0,
+	UPBOARD_UP2_BIT_SPI2_CLK,
+	UPBOARD_UP2_BIT_SPI1_TXD,
+	UPBOARD_UP2_BIT_SPI1_RXD,
+	UPBOARD_UP2_BIT_SPI1_FS1,
+	UPBOARD_UP2_BIT_SPI1_FS0,
+	UPBOARD_UP2_BIT_SPI1_CLK,
+	UPBOARD_UP2_BIT_I2C0_SCL,
+	UPBOARD_UP2_BIT_I2C0_SDA,
+	UPBOARD_UP2_BIT_I2C1_SCL,
+	UPBOARD_UP2_BIT_I2C1_SDA,
+	UPBOARD_UP2_BIT_PWM1,
+	UPBOARD_UP2_BIT_PWM0,
+	UPBOARD_UP2_BIT_EXHAT_LVDS0n,
+	UPBOARD_UP2_BIT_EXHAT_LVDS0p,
+	UPBOARD_UP2_BIT_GPIO24,
+	UPBOARD_UP2_BIT_GPIO10,
+	UPBOARD_UP2_BIT_GPIO2,
+	UPBOARD_UP2_BIT_GPIO1,
+	UPBOARD_UP2_BIT_EXHAT_LVDS3n,
+	UPBOARD_UP2_BIT_EXHAT_LVDS3p,
+	UPBOARD_UP2_BIT_EXHAT_LVDS4n,
+	UPBOARD_UP2_BIT_EXHAT_LVDS4p,
+	UPBOARD_UP2_BIT_EXHAT_LVDS5n,
+	UPBOARD_UP2_BIT_EXHAT_LVDS5p,
+	UPBOARD_UP2_BIT_I2S_SDO,
+	UPBOARD_UP2_BIT_I2S_SDI,
+	UPBOARD_UP2_BIT_I2S_WS_SYNC,
+	UPBOARD_UP2_BIT_I2S_BCLK,
+	UPBOARD_UP2_BIT_EXHAT_LVDS6n,
+	UPBOARD_UP2_BIT_EXHAT_LVDS6p,
+	UPBOARD_UP2_BIT_EXHAT_LVDS7n,
+	UPBOARD_UP2_BIT_EXHAT_LVDS7p,
+	UPBOARD_UP2_BIT_EXHAT_LVDS2n,
+	UPBOARD_UP2_BIT_EXHAT_LVDS2p,
+};
+
+static const struct pinctrl_pin_desc upboard_up2_pins[] = {
+	UPBOARD_UP2_PIN_NAME(UART1_TXD),
+	UPBOARD_UP2_PIN_NAME(UART1_RXD),
+	UPBOARD_UP2_PIN_NAME(UART1_RTS),
+	UPBOARD_UP2_PIN_NAME(UART1_CTS),
+	UPBOARD_UP2_PIN_NAME(GPIO3_ADC0),
+	UPBOARD_UP2_PIN_NAME(GPIO5_ADC2),
+	UPBOARD_UP2_PIN_NAME(GPIO6_ADC3),
+	UPBOARD_UP2_PIN_NAME(GPIO11),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS1n),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS1p),
+	UPBOARD_UP2_PIN_NAME(SPI2_TXD),
+	UPBOARD_UP2_PIN_NAME(SPI2_RXD),
+	UPBOARD_UP2_PIN_NAME(SPI2_FS1),
+	UPBOARD_UP2_PIN_NAME(SPI2_FS0),
+	UPBOARD_UP2_PIN_NAME(SPI2_CLK),
+	UPBOARD_UP2_PIN_NAME(SPI1_TXD),
+	UPBOARD_UP2_PIN_NAME(SPI1_RXD),
+	UPBOARD_UP2_PIN_NAME(SPI1_FS1),
+	UPBOARD_UP2_PIN_NAME(SPI1_FS0),
+	UPBOARD_UP2_PIN_NAME(SPI1_CLK),
+	UPBOARD_UP2_PIN_MUX(I2C0_SCL, &upboard_i2c0_reg),
+	UPBOARD_UP2_PIN_MUX(I2C0_SDA, &upboard_i2c0_reg),
+	UPBOARD_UP2_PIN_MUX(I2C1_SCL, &upboard_i2c1_reg),
+	UPBOARD_UP2_PIN_MUX(I2C1_SDA, &upboard_i2c1_reg),
+	UPBOARD_UP2_PIN_NAME(PWM1),
+	UPBOARD_UP2_PIN_NAME(PWM0),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS0n),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS0p),
+	UPBOARD_UP2_PIN_MUX(GPIO24, &upboard_i2c0_reg),
+	UPBOARD_UP2_PIN_MUX(GPIO10, &upboard_i2c0_reg),
+	UPBOARD_UP2_PIN_MUX(GPIO2, &upboard_i2c1_reg),
+	UPBOARD_UP2_PIN_MUX(GPIO1, &upboard_i2c1_reg),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS3n),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS3p),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS4n),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS4p),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS5n),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS5p),
+	UPBOARD_UP2_PIN_NAME(I2S_SDO),
+	UPBOARD_UP2_PIN_NAME(I2S_SDI),
+	UPBOARD_UP2_PIN_NAME(I2S_WS_SYNC),
+	UPBOARD_UP2_PIN_NAME(I2S_BCLK),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS6n),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS6p),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS7n),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS7p),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS2n),
+	UPBOARD_UP2_PIN_NAME(EXHAT_LVDS2p),
+};
+
+static const unsigned int upboard_up2_pin_header[] = {
+	UPBOARD_UP2_BIT_TO_PIN(GPIO10),
+	UPBOARD_UP2_BIT_TO_PIN(GPIO24),
+	UPBOARD_UP2_BIT_TO_PIN(GPIO1),
+	UPBOARD_UP2_BIT_TO_PIN(GPIO2),
+	UPBOARD_UP2_BIT_TO_PIN(GPIO3_ADC0),
+	UPBOARD_UP2_BIT_TO_PIN(GPIO11),
+	UPBOARD_UP2_BIT_TO_PIN(SPI2_CLK),
+	UPBOARD_UP2_BIT_TO_PIN(SPI1_FS1),
+	UPBOARD_UP2_BIT_TO_PIN(SPI1_FS0),
+	UPBOARD_UP2_BIT_TO_PIN(SPI1_RXD),
+	UPBOARD_UP2_BIT_TO_PIN(SPI1_TXD),
+	UPBOARD_UP2_BIT_TO_PIN(SPI1_CLK),
+	UPBOARD_UP2_BIT_TO_PIN(PWM0),
+	UPBOARD_UP2_BIT_TO_PIN(PWM1),
+	UPBOARD_UP2_BIT_TO_PIN(UART1_TXD),
+	UPBOARD_UP2_BIT_TO_PIN(UART1_RXD),
+	UPBOARD_UP2_BIT_TO_PIN(UART1_CTS),
+	UPBOARD_UP2_BIT_TO_PIN(UART1_RTS),
+	UPBOARD_UP2_BIT_TO_PIN(I2S_BCLK),
+	UPBOARD_UP2_BIT_TO_PIN(I2S_WS_SYNC),
+	UPBOARD_UP2_BIT_TO_PIN(I2S_SDI),
+	UPBOARD_UP2_BIT_TO_PIN(I2S_SDO),
+	UPBOARD_UP2_BIT_TO_PIN(GPIO6_ADC3),
+	UPBOARD_UP2_BIT_TO_PIN(SPI2_FS1),
+	UPBOARD_UP2_BIT_TO_PIN(SPI2_RXD),
+	UPBOARD_UP2_BIT_TO_PIN(SPI2_TXD),
+	UPBOARD_UP2_BIT_TO_PIN(SPI2_FS0),
+	UPBOARD_UP2_BIT_TO_PIN(GPIO5_ADC2),
+};
+
+static const unsigned int upboard_up2_uart1_pins[] = {
+	UPBOARD_UP2_BIT_TO_PIN(UART1_TXD),
+	UPBOARD_UP2_BIT_TO_PIN(UART1_RXD),
+	UPBOARD_UP2_BIT_TO_PIN(UART1_RTS),
+	UPBOARD_UP2_BIT_TO_PIN(UART1_CTS),
+};
+
+static const enum upboard_pin_mode upboard_up2_uart1_modes[] = {
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_IN,
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_IN
+};
+
+static_assert(ARRAY_SIZE(upboard_up2_uart1_modes) ==
+	      ARRAY_SIZE(upboard_up2_uart1_pins));
+
+static const unsigned int upboard_up2_i2c0_pins[] = {
+	UPBOARD_UP2_BIT_TO_PIN(I2C0_SCL),
+	UPBOARD_UP2_BIT_TO_PIN(I2C0_SDA),
+	UPBOARD_UP2_BIT_TO_PIN(GPIO24),
+	UPBOARD_UP2_BIT_TO_PIN(GPIO10),
+};
+
+static const unsigned int upboard_up2_i2c1_pins[] = {
+	UPBOARD_UP2_BIT_TO_PIN(I2C1_SCL),
+	UPBOARD_UP2_BIT_TO_PIN(I2C1_SDA),
+	UPBOARD_UP2_BIT_TO_PIN(GPIO2),
+	UPBOARD_UP2_BIT_TO_PIN(GPIO1),
+};
+
+static const unsigned int upboard_up2_spi1_pins[] = {
+	UPBOARD_UP2_BIT_TO_PIN(SPI1_TXD),
+	UPBOARD_UP2_BIT_TO_PIN(SPI1_RXD),
+	UPBOARD_UP2_BIT_TO_PIN(SPI1_FS1),
+	UPBOARD_UP2_BIT_TO_PIN(SPI1_FS0),
+	UPBOARD_UP2_BIT_TO_PIN(SPI1_CLK),
+};
+
+static const unsigned int upboard_up2_spi2_pins[] = {
+	UPBOARD_UP2_BIT_TO_PIN(SPI2_TXD),
+	UPBOARD_UP2_BIT_TO_PIN(SPI2_RXD),
+	UPBOARD_UP2_BIT_TO_PIN(SPI2_FS1),
+	UPBOARD_UP2_BIT_TO_PIN(SPI2_FS0),
+	UPBOARD_UP2_BIT_TO_PIN(SPI2_CLK),
+};
+
+static const enum upboard_pin_mode upboard_up2_spi_modes[] = {
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_IN,
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_OUT,
+};
+
+static_assert(ARRAY_SIZE(upboard_up2_spi_modes) ==
+	      ARRAY_SIZE(upboard_up2_spi1_pins));
+
+static_assert(ARRAY_SIZE(upboard_up2_spi_modes) ==
+	      ARRAY_SIZE(upboard_up2_spi2_pins));
+
+static const unsigned int upboard_up2_i2s0_pins[] = {
+	UPBOARD_UP2_BIT_TO_PIN(I2S_BCLK),
+	UPBOARD_UP2_BIT_TO_PIN(I2S_WS_SYNC),
+	UPBOARD_UP2_BIT_TO_PIN(I2S_SDI),
+	UPBOARD_UP2_BIT_TO_PIN(I2S_SDO),
+};
+
+static const enum upboard_pin_mode upboard_up2_i2s0_modes[] = {
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_OUT,
+	UPBOARD_PIN_MODE_GPIO_IN,
+	UPBOARD_PIN_MODE_GPIO_OUT
+};
+
+static_assert(ARRAY_SIZE(upboard_up2_i2s0_modes) ==
+	      ARRAY_SIZE(upboard_up2_i2s0_pins));
+
+static const unsigned int upboard_up2_pwm0_pins[] = {
+	UPBOARD_UP2_BIT_TO_PIN(PWM0),
+};
+
+static const unsigned int upboard_up2_pwm1_pins[] = {
+	UPBOARD_UP2_BIT_TO_PIN(PWM1),
+};
+
+static const unsigned int upboard_up2_adc0_pins[] = {
+	UPBOARD_UP2_BIT_TO_PIN(GPIO3_ADC0),
+};
+
+static const unsigned int upboard_up2_adc2_pins[] = {
+	UPBOARD_UP2_BIT_TO_PIN(GPIO5_ADC2),
+};
+
+static const unsigned int upboard_up2_adc3_pins[] = {
+	UPBOARD_UP2_BIT_TO_PIN(GPIO6_ADC3),
+};
+
+static const struct upboard_pingroup upboard_up2_pin_groups[] = {
+	UPBOARD_PINGROUP_MODES("uart1_grp", upboard_up2_uart1_pins, upboard_up2_uart1_modes),
+	UPBOARD_PINGROUP_MODE("i2c0_grp", upboard_up2_i2c0_pins, UPBOARD_PIN_MODE_FUNCTION),
+	UPBOARD_PINGROUP_MODE("i2c1_grp", upboard_up2_i2c1_pins, UPBOARD_PIN_MODE_FUNCTION),
+	UPBOARD_PINGROUP_MODES("spi1_grp", upboard_up2_spi1_pins, upboard_up2_spi_modes),
+	UPBOARD_PINGROUP_MODES("spi2_grp", upboard_up2_spi2_pins, upboard_up2_spi_modes),
+	UPBOARD_PINGROUP_MODES("i2s0_grp", upboard_up2_i2s0_pins, upboard_up2_i2s0_modes),
+	UPBOARD_PINGROUP_MODE("pwm0_grp", upboard_up2_pwm0_pins, UPBOARD_PIN_MODE_GPIO_OUT),
+	UPBOARD_PINGROUP_MODE("pwm1_grp", upboard_up2_pwm1_pins, UPBOARD_PIN_MODE_GPIO_OUT),
+	UPBOARD_PINGROUP_MODE("adc0_grp", upboard_up2_adc0_pins, UPBOARD_PIN_MODE_GPIO_IN),
+	UPBOARD_PINGROUP_MODE("adc2_grp", upboard_up2_adc2_pins, UPBOARD_PIN_MODE_GPIO_IN),
+	UPBOARD_PINGROUP_MODE("adc3_grp", upboard_up2_adc3_pins, UPBOARD_PIN_MODE_GPIO_IN),
+};
+
+static const char * const upboard_up2_uart1_groups[] = { "uart1_grp" };
+static const char * const upboard_up2_i2c0_groups[]  = { "i2c0_grp" };
+static const char * const upboard_up2_i2c1_groups[]  = { "i2c1_grp" };
+static const char * const upboard_up2_spi1_groups[]  = { "spi1_grp" };
+static const char * const upboard_up2_spi2_groups[]  = { "spi2_grp" };
+static const char * const upboard_up2_i2s0_groups[]  = { "i2s0_grp" };
+static const char * const upboard_up2_pwm0_groups[]  = { "pwm0_grp" };
+static const char * const upboard_up2_pwm1_groups[]  = { "pwm1_grp" };
+static const char * const upboard_up2_adc0_groups[]  = { "adc0_grp" };
+static const char * const upboard_up2_adc2_groups[]  = { "adc2_grp" };
+static const char * const upboard_up2_adc3_groups[]  = { "adc3_grp" };
+
+static const struct pinfunction upboard_up2_pin_functions[] = {
+	UPBOARD_FUNCTION("uart1", upboard_up2_uart1_groups),
+	UPBOARD_FUNCTION("i2c0", upboard_up2_i2c0_groups),
+	UPBOARD_FUNCTION("i2c1", upboard_up2_i2c1_groups),
+	UPBOARD_FUNCTION("spi1", upboard_up2_spi1_groups),
+	UPBOARD_FUNCTION("spi2", upboard_up2_spi2_groups),
+	UPBOARD_FUNCTION("i2s0", upboard_up2_i2s0_groups),
+	UPBOARD_FUNCTION("pwm0", upboard_up2_pwm0_groups),
+	UPBOARD_FUNCTION("pwm1", upboard_up2_pwm1_groups),
+	UPBOARD_FUNCTION("adc0", upboard_up2_adc0_groups),
+	UPBOARD_FUNCTION("adc2", upboard_up2_adc2_groups),
+	UPBOARD_FUNCTION("adc3", upboard_up2_adc3_groups),
+};
+
+static const struct upboard_pinctrl_data upboard_up2_pinctrl_data = {
+	.groups = &upboard_up2_pin_groups[0],
+	.ngroups = ARRAY_SIZE(upboard_up2_pin_groups),
+	.funcs = &upboard_up2_pin_functions[0],
+	.nfuncs = ARRAY_SIZE(upboard_up2_pin_functions),
+	.pin_header = &upboard_up2_pin_header[0],
+	.ngpio = ARRAY_SIZE(upboard_up2_pin_header),
+};
+
+static int upboard_pinctrl_set_function(struct pinctrl_dev *pctldev, unsigned int offset)
+{
+	struct upboard_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	struct upboard_pin *p = &pctrl->pins[offset];
+	int ret;
+
+	if (!p->funcbit)
+		return -EPERM;
+
+	ret = regmap_field_write(p->enbit, 0);
+	if (ret)
+		return ret;
+
+	return regmap_field_write(p->funcbit, 1);
+}
+
+static int upboard_pinctrl_gpio_commit_enable(struct pinctrl_dev *pctldev, unsigned int offset)
+{
+	struct upboard_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	struct upboard_pin *p = &pctrl->pins[offset];
+
+	if (p->funcbit) {
+		int ret = regmap_field_write(p->funcbit, 0);
+
+		if (ret)
+			return ret;
+	}
+
+	return regmap_field_write(p->enbit, 1);
+}
+
+static int upboard_pinctrl_gpio_request_enable(struct pinctrl_dev *pctldev,
+					       struct pinctrl_gpio_range *range,
+					       unsigned int offset)
+{
+	return upboard_pinctrl_gpio_commit_enable(pctldev, offset);
+}
+
+static void upboard_pinctrl_gpio_commit_disable(struct pinctrl_dev *pctldev, unsigned int offset)
+{
+	struct upboard_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	struct upboard_pin *p = &pctrl->pins[offset];
+
+	regmap_field_write(p->enbit, 0);
+};
+
+static void upboard_pinctrl_gpio_disable_free(struct pinctrl_dev *pctldev,
+					      struct pinctrl_gpio_range *range, unsigned int offset)
+{
+	return upboard_pinctrl_gpio_commit_disable(pctldev, offset);
+}
+
+static int upboard_pinctrl_gpio_commit_direction(struct pinctrl_dev *pctldev, unsigned int offset,
+						 bool input)
+{
+	struct upboard_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	struct upboard_pin *p = &pctrl->pins[offset];
+
+	return regmap_field_write(p->dirbit, input);
+}
+
+static int upboard_pinctrl_gpio_set_direction(struct pinctrl_dev *pctldev,
+					      struct pinctrl_gpio_range *range,
+					      unsigned int offset, bool input)
+{
+	return upboard_pinctrl_gpio_commit_direction(pctldev, offset, input);
+}
+
+static int upboard_pinctrl_set_mux(struct pinctrl_dev *pctldev, unsigned int func_selector,
+				   unsigned int group_selector)
+{
+	struct upboard_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	const struct upboard_pinctrl_data *pctrl_data = pctrl->pctrl_data;
+	const struct upboard_pingroup *upgroups = pctrl_data->groups;
+	struct group_desc *grp;
+	int mode, ret, i;
+
+	grp = pinctrl_generic_get_group(pctldev, group_selector);
+	if (!grp)
+		return -EINVAL;
+
+	for (i = 0; i < grp->grp.npins; i++) {
+		mode = upgroups[group_selector].mode ? upgroups[group_selector].mode :
+			upgroups[group_selector].modes[i];
+
+		if (mode == UPBOARD_PIN_MODE_FUNCTION) {
+			ret = upboard_pinctrl_set_function(pctldev, grp->grp.pins[i]);
+			if (ret)
+				return ret;
+
+			continue;
+		}
+
+		ret = upboard_pinctrl_gpio_commit_enable(pctldev, grp->grp.pins[i]);
+		if (ret)
+			return ret;
+
+		ret = upboard_pinctrl_gpio_commit_direction(pctldev, grp->grp.pins[i],
+							    mode == UPBOARD_PIN_MODE_GPIO_IN ?
+							    true : false);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static const struct pinmux_ops upboard_pinmux_ops = {
+	.get_functions_count = pinmux_generic_get_function_count,
+	.get_function_name = pinmux_generic_get_function_name,
+	.get_function_groups = pinmux_generic_get_function_groups,
+	.set_mux = upboard_pinctrl_set_mux,
+	.gpio_request_enable = upboard_pinctrl_gpio_request_enable,
+	.gpio_disable_free = upboard_pinctrl_gpio_disable_free,
+	.gpio_set_direction = upboard_pinctrl_gpio_set_direction,
+};
+
+static int upboard_pinctrl_pin_get_mode(struct pinctrl_dev *pctldev, unsigned int pin)
+{
+	struct upboard_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+	struct upboard_pin *p = &pctrl->pins[pin];
+
+	unsigned int val;
+	int ret;
+
+	if (p->funcbit) {
+		ret = regmap_field_read(p->funcbit, &val);
+		if (ret)
+			return ret;
+		if (val)
+			return UPBOARD_PIN_MODE_FUNCTION;
+	}
+
+	ret = regmap_field_read(p->enbit, &val);
+	if (ret)
+		return ret;
+	if (!val)
+		return UPBOARD_PIN_MODE_DISABLED;
+
+	ret = regmap_field_read(p->dirbit, &val);
+	if (ret)
+		return ret;
+
+	return val ? UPBOARD_PIN_MODE_GPIO_IN : UPBOARD_PIN_MODE_GPIO_OUT;
+}
+
+static void upboard_pinctrl_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s,
+				     unsigned int offset)
+{
+	int ret = upboard_pinctrl_pin_get_mode(pctldev, offset);
+
+	if (ret == UPBOARD_PIN_MODE_FUNCTION)
+		seq_puts(s, "mode function ");
+	else if (ret == UPBOARD_PIN_MODE_DISABLED)
+		seq_puts(s, "HIGH-Z");
+	else
+		seq_printf(s, "GPIO (%s) ", ret == UPBOARD_PIN_MODE_GPIO_IN ? "input" : "output");
+}
+
+static const struct pinctrl_ops upboard_pinctrl_ops = {
+	.get_groups_count = pinctrl_generic_get_group_count,
+	.get_group_name = pinctrl_generic_get_group_name,
+	.get_group_pins = pinctrl_generic_get_group_pins,
+	.pin_dbg_show = upboard_pinctrl_dbg_show,
+};
+
+static int upboard_gpio_request(struct gpio_chip *gc, unsigned int offset)
+{
+	struct gpiochip_fwd *fwd = container_of(gc, struct gpiochip_fwd, chip);
+	struct upboard_pinctrl *pctrl = fwd->data;
+	unsigned int pin = pctrl->pctrl_data->pin_header[offset];
+	struct gpio_desc *desc;
+	int ret;
+
+	ret = pinctrl_gpio_request(gc, offset);
+	if (ret)
+		return ret;
+
+	/* GPIO desc is already registered */
+	if (fwd->descs[offset])
+		return 0;
+
+	desc = gpiod_get_index(pctrl->dev, "external", pin, 0);
+	if (IS_ERR(desc)) {
+		pinctrl_gpio_free(gc, offset);
+		return PTR_ERR(desc);
+	}
+
+	return gpiochip_fwd_add_gpio_desc(fwd, desc, offset);
+}
+
+static void upboard_gpio_free(struct gpio_chip *gc, unsigned int offset)
+{
+	pinctrl_gpio_free(gc, offset);
+}
+
+static int upboard_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
+{
+	struct gpiochip_fwd *fwd = container_of(gc, struct gpiochip_fwd, chip);
+	struct upboard_pinctrl *pctrl = fwd->data;
+	unsigned int pin = pctrl->pctrl_data->pin_header[offset];
+	int mode;
+
+	mode = upboard_pinctrl_pin_get_mode(pctrl->pctldev, pin);
+
+	/* If the pin is in function mode or high-z, input direction is returned */
+	if (mode < 0)
+		return mode;
+
+	if (mode == UPBOARD_PIN_MODE_GPIO_OUT)
+		return GPIO_LINE_DIRECTION_OUT;
+	else
+		return GPIO_LINE_DIRECTION_IN;
+}
+
+static int upboard_gpio_direction_input(struct gpio_chip *gc, unsigned int offset)
+{
+	int ret;
+
+	ret = pinctrl_gpio_direction_input(gc, offset);
+	if (ret)
+		return ret;
+
+	return gpio_fwd_direction_input(gc, offset);
+}
+
+static int upboard_gpio_direction_output(struct gpio_chip *gc, unsigned int offset, int value)
+{
+	int ret;
+
+	ret = pinctrl_gpio_direction_output(gc, offset);
+	if (ret)
+		return ret;
+
+	return gpio_fwd_direction_output(gc, offset, value);
+}
+
+static int upboard_pinctrl_register_groups(struct upboard_pinctrl *pctrl)
+{
+	const struct upboard_pingroup *groups = pctrl->pctrl_data->groups;
+	size_t ngroups = pctrl->pctrl_data->ngroups;
+	int ret, i;
+
+	for (i = 0; i < ngroups; i++) {
+		ret = pinctrl_generic_add_group(pctrl->pctldev, groups[i].grp.name,
+						groups[i].grp.pins, groups[i].grp.npins, pctrl);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int upboard_pinctrl_register_functions(struct upboard_pinctrl *pctrl)
+{
+	const struct pinfunction *funcs = pctrl->pctrl_data->funcs;
+	size_t nfuncs = pctrl->pctrl_data->nfuncs;
+	int ret, i;
+
+	for (i = 0; i < nfuncs ; ++i) {
+		ret = pinmux_generic_add_function(pctrl->pctldev, funcs[i].name, funcs[i].groups,
+						  funcs[i].ngroups, NULL);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static const struct pinctrl_map upboard_pinctrl_mapping_up_apl01[] = {
+	PIN_MAP_MUX_GROUP_DEFAULT("upboard-pinctrl", "INT3452:00", "pwm0_grp", "pwm0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("upboard-pinctrl", "INT3452:00", "pwm1_grp", "pwm1"),
+	PIN_MAP_MUX_GROUP_DEFAULT("upboard-pinctrl", "INT3452:00", "uart1_grp", "uart1"),
+	PIN_MAP_MUX_GROUP_DEFAULT("upboard-pinctrl", "INT3452:02", "i2c0_grp", "i2c0"),
+	PIN_MAP_MUX_GROUP_DEFAULT("upboard-pinctrl", "INT3452:02", "i2c1_grp", "i2c1"),
+	PIN_MAP_MUX_GROUP_DEFAULT("upboard-pinctrl", "INT3452:01", "ssp0_grp", "ssp0"),
+};
+
+static const struct dmi_system_id dmi_platform_info[] = {
+	{
+		/* UP Squared */
+		.matches = {
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "AAEON"),
+			DMI_EXACT_MATCH(DMI_BOARD_NAME, "UP-APL01"),
+		},
+		.driver_data = (void *)BOARD_UP_APL01,
+	},
+	{ },
+};
+
+static int upboard_pinctrl_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct upboard_fpga *fpga = dev_get_drvdata(dev->parent);
+	const struct dmi_system_id *dmi_id;
+	enum upboard_board_id board_id;
+	struct pinctrl_desc *pctldesc;
+	struct upboard_pinctrl *pctrl;
+	struct upboard_pin *pins;
+	struct gpiochip_fwd *fwd;
+	struct pinctrl *pinctrl;
+	struct gpio_chip *chip;
+	int ret, i;
+
+	pctldesc = devm_kzalloc(dev, sizeof(*pctldesc), GFP_KERNEL);
+	if (!pctldesc)
+		return -ENOMEM;
+
+	pctrl = devm_kzalloc(dev, sizeof(*pctrl), GFP_KERNEL);
+	if (!pctrl)
+		return -ENOMEM;
+
+	switch (fpga->fpga_data->type) {
+	case UPBOARD_UP_FPGA:
+		pctldesc->pins = upboard_up_pins;
+		pctldesc->npins = ARRAY_SIZE(upboard_up_pins);
+		pctrl->pctrl_data = &upboard_up_pinctrl_data;
+		break;
+	case UPBOARD_UP2_FPGA:
+		pctldesc->pins = upboard_up2_pins;
+		pctldesc->npins = ARRAY_SIZE(upboard_up2_pins);
+		pctrl->pctrl_data = &upboard_up2_pinctrl_data;
+		break;
+	default:
+		return dev_err_probe(dev, -ENODEV, "Unsupported device type %d\n",
+				     fpga->fpga_data->type);
+	}
+
+	dmi_id = dmi_first_match(dmi_platform_info);
+	if (IS_ERR_OR_NULL(dmi_id))
+		return -ENODEV;
+
+	board_id = (enum upboard_board_id)dmi_id->driver_data;
+
+	switch (board_id) {
+	case BOARD_UP_APL01:
+		pctrl->maps = upboard_pinctrl_mapping_up_apl01;
+		pctrl->nmaps = ARRAY_SIZE(upboard_pinctrl_mapping_up_apl01);
+		break;
+	default:
+		return dev_err_probe(dev, -ENODEV, "Unsupported board\n");
+	}
+
+	pctldesc->name = dev_name(dev);
+	pctldesc->owner = THIS_MODULE;
+	pctldesc->pctlops = &upboard_pinctrl_ops;
+	pctldesc->pmxops = &upboard_pinmux_ops;
+
+	pctrl->dev = dev;
+
+	pins = devm_kcalloc(dev, pctldesc->npins, sizeof(*pins), GFP_KERNEL);
+	if (!pins)
+		return -ENOMEM;
+
+	/* Initialize pins */
+	for (i = 0; i < pctldesc->npins; i++) {
+		const struct pinctrl_pin_desc *pin_desc = &pctldesc->pins[i];
+		unsigned int regoff = pin_desc->number / UPBOARD_REGISTER_SIZE;
+		unsigned int lsb = pin_desc->number % UPBOARD_REGISTER_SIZE;
+		struct reg_field * const fld_func = pin_desc->drv_data;
+		struct upboard_pin *pin = &pins[i];
+		struct reg_field fldconf = {};
+
+		if (fld_func) {
+			pin->funcbit = devm_regmap_field_alloc(dev, fpga->regmap, *fld_func);
+
+			if (IS_ERR(pin->funcbit))
+				return PTR_ERR(pin->funcbit);
+		}
+
+		fldconf.reg = UPBOARD_REG_GPIO_EN0 + regoff;
+		fldconf.lsb = lsb;
+		fldconf.msb = lsb;
+		pin->enbit = devm_regmap_field_alloc(dev, fpga->regmap, fldconf);
+		if (IS_ERR(pin->enbit))
+			return PTR_ERR(pin->enbit);
+
+		fldconf.reg = UPBOARD_REG_GPIO_DIR0 + regoff;
+		fldconf.lsb = lsb;
+		fldconf.msb = lsb;
+		pin->dirbit = devm_regmap_field_alloc(dev, fpga->regmap, fldconf);
+		if (IS_ERR(pin->dirbit))
+			return PTR_ERR(pin->dirbit);
+	}
+
+	pctrl->pins = pins;
+
+	ret = devm_pinctrl_register_and_init(dev, pctldesc, pctrl, &pctrl->pctldev);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to register pinctrl\n");
+
+	ret = upboard_pinctrl_register_groups(pctrl);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to register groups\n");
+
+	ret = upboard_pinctrl_register_functions(pctrl);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to register functions\n");
+
+	ret = pinctrl_register_mappings(pctrl->maps, pctrl->nmaps);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to register pinctrl mappings\n");
+
+	pinctrl = devm_pinctrl_get_select_default(dev);
+	if (IS_ERR(pinctrl)) {
+		ret = PTR_ERR(pinctrl);
+		dev_err(dev, "Failed to select pinctrl: %d\n", ret);
+		goto free_mapping;
+	}
+
+	ret = pinctrl_enable(pctrl->pctldev);
+	if (ret) {
+		dev_err(dev, "Failed to enable pinctrl: %d\n", ret);
+		goto free_mapping;
+	}
+
+	fwd = devm_gpiochip_fwd_alloc(dev, pctrl->pctrl_data->ngpio);
+	if (IS_ERR(fwd)) {
+		ret = PTR_ERR(fwd);
+		dev_err(dev, "Failed to allocate the gpiochip fowarder: %d\n", ret);
+		goto free_mapping;
+	}
+
+	chip = &fwd->chip;
+	chip->request = upboard_gpio_request;
+	chip->free = upboard_gpio_free;
+	chip->get_direction = upboard_gpio_get_direction;
+	chip->direction_output = upboard_gpio_direction_output;
+	chip->direction_input = upboard_gpio_direction_input;
+
+	ret = gpiochip_fwd_register(fwd, pctrl);
+	if (ret) {
+		dev_err(dev, "Failed to register the gpiochip forwarder: %d\n", ret);
+		goto free_mapping;
+	}
+
+	return gpiochip_add_pin_range_sparse(chip, dev_name(dev), 0, pctrl->pctrl_data->pin_header,
+					     pctrl->pctrl_data->ngpio);
+
+free_mapping:
+	pinctrl_unregister_mappings(pctrl->maps);
+
+	return ret;
+}
+
+static struct platform_driver upboard_pinctrl_driver = {
+	.driver = {
+		.name = "upboard-pinctrl",
+	},
+	.probe = upboard_pinctrl_probe,
+};
+
+module_platform_driver(upboard_pinctrl_driver);
+
+MODULE_AUTHOR("Gary Wang <garywang@aaeon.com.tw>");
+MODULE_AUTHOR("Thomas Richard <thomas.richard@bootlin.com");
+MODULE_DESCRIPTION("UP Board HAT pin controller driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:upboard-pinctrl");