[0/4] RFC: Realtek 83xx SMI driver core

Message ID 20171105231909.5599-1-linus.walleij@linaro.org
Headers show
Series
  • RFC: Realtek 83xx SMI driver core
Related show

Message

Linus Walleij Nov. 5, 2017, 11:19 p.m.
Hi folks,

I'm working a bit on this. Since DSA is big, complex and hard for
a novice I just wanted to throw what I have in my tree out there
so you can take a look at how I hacked this up and give me some
help how to continue.

I am running it for trials on the D-Link DIR-685 and it looks
fun, but my ethernet driver for Gemini is not yet working so
I cannot really do proper testing. I'll get there I guess.

Example from dmesg:
realtek-smi 0.switch: deasserted RESET
realtek-smi 0.switch: found an RTL8366RB switch
DSA: switch 0 0 parsed
DSA: tree 0 parsed
realtek-smi 0.switch: RTL5937 ver 3 chip found
realtek-smi 0.switch: active low/falling IRQ
realtek-smi 0.switch: set MAC: CE:32:3B:FB:58:13
libphy: dsa slave smi: probed
RTL8366RB Gigabit Ethernet dsa-0.0:00: attached PHY driver [RTL8366RB Gigabit Ethernet] (mii_bus:phy_addr=dsa-0.0:00, irq=37)
RTL8366RB Gigabit Ethernet dsa-0.0:01: attached PHY driver [RTL8366RB Gigabit Ethernet] (mii_bus:phy_addr=dsa-0.0:01, irq=38)
RTL8366RB Gigabit Ethernet dsa-0.0:02: attached PHY driver [RTL8366RB Gigabit Ethernet] (mii_bus:phy_addr=dsa-0.0:02, irq=39)
RTL8366RB Gigabit Ethernet dsa-0.0:03: attached PHY driver [RTL8366RB Gigabit Ethernet] (mii_bus:phy_addr=dsa-0.0:03, irq=40)
RTL8366RB Gigabit Ethernet dsa-0.0:04: attached PHY driver [RTL8366RB Gigabit Ethernet] (mii_bus:phy_addr=dsa-0.0:04, irq=41)
realtek-smi 0.switch: adjust link on CPU port
gmac-gemini 60000000.ethernet eth0: connected to PHY "fixed-0:00"
Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL)
phy_id=0x00000000, phy_mode=rgmii
gmac-gemini 60000000.ethernet: set GMAC0 and GMAC1 to MII/RGMII mode
gmac-gemini 60000000.ethernet eth0: connect to RGMII
gmac-gemini 60000000.ethernet eth0: opened
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
realtek-smi 0.switch: enable port 0
IPv6: ADDRCONF(NETDEV_UP): lan0: link is not ready
realtek-smi 0.switch lan0: Link is Down
realtek-smi 0.switch lan0: Link is Up - 1Gbps/Full - flow control rx/tx
IPv6: ADDRCONF(NETDEV_CHANGE): lan0: link becomes ready

cat /proc/interrupts
 36:          6  FTGPIO010  15 Level     RTL8366RB
 37:          3  RTL8366RB   0 Edge      dsa-0.0:00
 38:          0  RTL8366RB   1 Edge      dsa-0.0:01
 39:          2  RTL8366RB   2 Edge      dsa-0.0:02
 40:          2  RTL8366RB   3 Edge      dsa-0.0:03
 41:          0  RTL8366RB   4 Edge      dsa-0.0:04

Plugged some cables in/out. Hooray, no polling needed.

Linus Walleij (4):
  RFC: net/dsa: Allow DSA PHYs to define link IRQs
  RFC: net: phy: realtek: Support RTL8366RB variant
  RFC: net: dsa: Add bindings for Realtek SMI DSAs
  RFC: net: dsa: realtek-smi: Add Realtek SMI driver

 .../devicetree/bindings/net/dsa/realtek-smi.txt    |  104 ++
 drivers/net/dsa/Kconfig                            |   12 +
 drivers/net/dsa/Makefile                           |    2 +
 drivers/net/dsa/realtek-smi.c                      |  436 ++++++++
 drivers/net/dsa/realtek-smi.h                      |  145 +++
 drivers/net/dsa/rtl8366.c                          |  493 +++++++++
 drivers/net/dsa/rtl8366rb.c                        | 1103 ++++++++++++++++++++
 drivers/net/phy/realtek.c                          |   32 +
 net/dsa/slave.c                                    |    8 +
 9 files changed, 2335 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/dsa/realtek-smi.txt
 create mode 100644 drivers/net/dsa/realtek-smi.c
 create mode 100644 drivers/net/dsa/realtek-smi.h
 create mode 100644 drivers/net/dsa/rtl8366.c
 create mode 100644 drivers/net/dsa/rtl8366rb.c

-- 
2.13.6

Comments

Carl-Daniel Hailfinger April 2, 2018, 4:10 p.m. | #1
Hi Linus,

did you make any progress with this?
I noticed that the Vodafone Easybox 904xdsl/904lte models both make use
of the RTL8367 switch. About one million of these routers have been
deployed in Germany.
There is an OpenWrt fork at
https://github.com/Quallenauge/Easybox-904-XDSL/commits/master-lede
which depends on the out-of-tree patches which seem to be the basis for
your Realtek 83xx driver patches.

Having your Realtek 83xx patches in the upstream Linux kernel would help
tremendously in getting support for those router models merged in OpenWrt.

Regards,
Carl-Daniel