diff mbox

[V6,3/3] MX53: support for freescale MX53LOCO board

Message ID 1303476945-17383-4-git-send-email-jason.hui@linaro.org
State New
Headers show

Commit Message

Jason Hui April 22, 2011, 12:55 p.m. UTC 
This patch add initial support for freescale MX53LOCO board.
Network(FEC),SD/MMC,UART have been supported by this patch

The patch also config CPU:1GHZ,DDR:400MHZ for better peformance

Signed-off-by: Jason Liu <jason.hui@linaro.org>
---
Changes since v5:
- merge the "Add power init support" patch
changes since v4:
- remove the boot reset cause from board support
changes since v3:
- include other two small patch into this commit,
mx53loco: set mmc env to MMC slot1
MX5: Enable flat-device-tree support on mx53 loco board
changes since V2:
-factor out the boot cause function to common code,
-fix gd->ram_size with full memory size
-remove the '1' from all #defines that just enable features
-correct memory test end address value
---
 MAINTAINERS                               |    1 +
 arch/arm/cpu/armv7/mx5/soc.c              |    2 +-
 arch/arm/include/asm/arch-mx5/sys_proto.h |    2 +
 board/freescale/mx53loco/Makefile         |   47 ++++
 board/freescale/mx53loco/imximage.cfg     |   96 +++++++
 board/freescale/mx53loco/mx53loco.c       |  395 +++++++++++++++++++++++++++++
 boards.cfg                                |    1 +
 include/configs/mx53loco.h                |  198 +++++++++++++++
 8 files changed, 741 insertions(+), 1 deletions(-)
diff mbox

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index 1299cbb..c00a196 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -567,6 +567,7 @@  Stefano Babic <sbabic@denx.de>
 Jason Liu <r64343@freescale.com>
 
 	mx53evk         i.MX53
+	mx53loco        i.MX53
 
 Enric Balletbo i Serra <eballetbo@iseebcn.com>
 
diff --git a/arch/arm/cpu/armv7/mx5/soc.c b/arch/arm/cpu/armv7/mx5/soc.c
index 6f4e8db..9c03474 100644
--- a/arch/arm/cpu/armv7/mx5/soc.c
+++ b/arch/arm/cpu/armv7/mx5/soc.c
@@ -116,7 +116,7 @@  int print_cpuinfo(void)
 		(cpurev & 0x000F0) >> 4,
 		(cpurev & 0x0000F) >> 0,
 		mxc_get_clock(MXC_ARM_CLK) / 1000000);
-	printf("Reset cause: %s\n", get_reset_cause());
+	printf("Reset  cause: %s\n", get_reset_cause());
 	return 0;
 }
 #endif
diff --git a/arch/arm/include/asm/arch-mx5/sys_proto.h b/arch/arm/include/asm/arch-mx5/sys_proto.h
index f687503..2d7e9ed 100644
--- a/arch/arm/include/asm/arch-mx5/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx5/sys_proto.h
@@ -27,5 +27,7 @@ 
 u32 get_cpu_rev(void);
 #define is_soc_rev(rev)	((get_cpu_rev() & 0xFF) - rev)
 void sdelay(unsigned long);
+void pmic_reg_write(u32 reg, u32 value);
+u32 pmic_reg_read(u32 reg);
 
 #endif
diff --git a/board/freescale/mx53loco/Makefile b/board/freescale/mx53loco/Makefile
new file mode 100644
index 0000000..2088a48
--- /dev/null
+++ b/board/freescale/mx53loco/Makefile
@@ -0,0 +1,47 @@ 
+#
+# (C) Copyright 2011 Freescale Semiconductor, Inc.
+# Jason Liu <r64343@freescale.com>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	:= mx53loco.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mx53loco/imximage.cfg b/board/freescale/mx53loco/imximage.cfg
new file mode 100644
index 0000000..ce9c8fc
--- /dev/null
+++ b/board/freescale/mx53loco/imximage.cfg
@@ -0,0 +1,96 @@ 
+# Copyright (C) 2011 Freescale Semiconductor, Inc.
+# Jason Liu <r64343@freescale.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not write to the Free Software
+# Foundation Inc. 51 Franklin Street Fifth Floor Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.imxmage for more details about how-to configure
+# and create imximage boot image
+#
+# The syntax is taken as close as possible with the kwbimage
+
+# image version
+
+IMAGE_VERSION 2
+
+# Boot Device : one of
+# spi, sd (the board has no nand neither onenand)
+
+BOOT_FROM	sd
+
+# Device Configuration Data (DCD)
+#
+# Each entry must have the format:
+# Addr-type           Address        Value
+#
+# where:
+#	Addr-type register length (1,2 or 4 bytes)
+#	Address	  absolute address of the register
+#	value	  value to be stored in the register
+
+DATA 4 0x53fa8554 0x00300000
+DATA 4 0x53fa8558 0x00300040
+DATA 4 0x53fa8560 0x00300000
+DATA 4 0x53fa8564 0x00300040
+DATA 4 0x53fa8568 0x00300040
+DATA 4 0x53fa8570 0x00300000
+DATA 4 0x53fa8574 0x00300000
+DATA 4 0x53fa8578 0x00300000
+DATA 4 0x53fa857c 0x00300040
+DATA 4 0x53fa8580 0x00300040
+DATA 4 0x53fa8584 0x00300000
+DATA 4 0x53fa8588 0x00300000
+DATA 4 0x53fa8590 0x00300040
+DATA 4 0x53fa8594 0x00300000
+DATA 4 0x53fa86f0 0x00300000
+DATA 4 0x53fa86f4 0x00000000
+DATA 4 0x53fa86fc 0x00000000
+DATA 4 0x53fa8714 0x00000000
+DATA 4 0x53fa8718 0x00300000
+DATA 4 0x53fa871c 0x00300000
+DATA 4 0x53fa8720 0x00300000
+DATA 4 0x53fa8724 0x04000000
+DATA 4 0x53fa8728 0x00300000
+DATA 4 0x53fa872c 0x00300000
+DATA 4 0x63fd9088 0x35343535
+DATA 4 0x63fd9090 0x4d444c44
+DATA 4 0x63fd907c 0x01370138
+DATA 4 0x63fd9080 0x013b013c
+DATA 4 0x63fd9018 0x00011740
+DATA 4 0x63fd9000 0xc3190000
+DATA 4 0x63fd900c 0x9f5152e3
+DATA 4 0x63fd9010 0xb68e8a63
+DATA 4 0x63fd9014 0x01ff00db
+DATA 4 0x63fd902c 0x000026d2
+DATA 4 0x63fd9030 0x009f0e21
+DATA 4 0x63fd9008 0x12273030
+DATA 4 0x63fd9004 0x0002002d
+DATA 4 0x63fd901c 0x00008032
+DATA 4 0x63fd901c 0x00008033
+DATA 4 0x63fd901c 0x00028031
+DATA 4 0x63fd901c 0x092080b0
+DATA 4 0x63fd901c 0x04008040
+DATA 4 0x63fd901c 0x0000803a
+DATA 4 0x63fd901c 0x0000803b
+DATA 4 0x63fd901c 0x00028039
+DATA 4 0x63fd901c 0x09208138
+DATA 4 0x63fd901c 0x04008048
+DATA 4 0x63fd9020 0x00001800
+DATA 4 0x63fd9040 0x04b80003
+DATA 4 0x63fd9058 0x00022227
+DATA 4 0x63fd901c 0x00000000
diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c
new file mode 100644
index 0000000..62ed400
--- /dev/null
+++ b/board/freescale/mx53loco/mx53loco.c
@@ -0,0 +1,395 @@ 
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Jason Liu <r64343@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx5x_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/clock.h>
+#include <asm/errno.h>
+#include <netdev.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <mxc_gpio.h>
+#include <da9053.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+u32 get_board_rev(void)
+{
+	return get_cpu_rev();
+}
+
+int dram_init(void)
+{
+	u32 size1, size2;
+
+	size1 = get_ram_size((volatile void *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
+	size2 = get_ram_size((volatile void *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE);
+
+	gd->ram_size = size1 + size2;
+
+	return 0;
+}
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+}
+
+static void setup_iomux_uart(void)
+{
+	/* UART1 RXD */
+	mxc_request_iomux(MX53_PIN_CSI0_D11, IOMUX_CONFIG_ALT2);
+	mxc_iomux_set_pad(MX53_PIN_CSI0_D11,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU |
+				PAD_CTL_ODE_OPENDRAIN_ENABLE);
+	mxc_iomux_set_input(MX53_UART1_IPP_UART_RXD_MUX_SELECT_INPUT, 0x1);
+
+	/* UART1 TXD */
+	mxc_request_iomux(MX53_PIN_CSI0_D10, IOMUX_CONFIG_ALT2);
+	mxc_iomux_set_pad(MX53_PIN_CSI0_D10,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU |
+				PAD_CTL_ODE_OPENDRAIN_ENABLE);
+}
+
+static void setup_iomux_fec(void)
+{
+	/*FEC_MDIO*/
+	mxc_request_iomux(MX53_PIN_FEC_MDIO, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_MDIO,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_22K_PU | PAD_CTL_ODE_OPENDRAIN_ENABLE);
+	mxc_iomux_set_input(MX53_FEC_FEC_MDI_SELECT_INPUT, 0x1);
+
+	/*FEC_MDC*/
+	mxc_request_iomux(MX53_PIN_FEC_MDC, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_MDC, PAD_CTL_DRV_HIGH);
+
+	/* FEC RXD1 */
+	mxc_request_iomux(MX53_PIN_FEC_RXD1, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_RXD1,
+			PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE);
+
+	/* FEC RXD0 */
+	mxc_request_iomux(MX53_PIN_FEC_RXD0, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_RXD0,
+			PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE);
+
+	 /* FEC TXD1 */
+	mxc_request_iomux(MX53_PIN_FEC_TXD1, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_TXD1, PAD_CTL_DRV_HIGH);
+
+	/* FEC TXD0 */
+	mxc_request_iomux(MX53_PIN_FEC_TXD0, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_TXD0, PAD_CTL_DRV_HIGH);
+
+	/* FEC TX_EN */
+	mxc_request_iomux(MX53_PIN_FEC_TX_EN, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_TX_EN, PAD_CTL_DRV_HIGH);
+
+	/* FEC TX_CLK */
+	mxc_request_iomux(MX53_PIN_FEC_REF_CLK, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_REF_CLK,
+			PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE);
+
+	/* FEC RX_ER */
+	mxc_request_iomux(MX53_PIN_FEC_RX_ER, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_RX_ER,
+			PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE);
+
+	/* FEC CRS */
+	mxc_request_iomux(MX53_PIN_FEC_CRS_DV, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_CRS_DV,
+			PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE);
+}
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg esdhc_cfg[2] = {
+	{MMC_SDHC1_BASE_ADDR, 1},
+	{MMC_SDHC3_BASE_ADDR, 1},
+};
+
+int board_mmc_getcd(u8 *cd, struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+
+	if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
+		*cd = mxc_gpio_get(77); /*GPIO3_13*/
+	else
+		*cd = mxc_gpio_get(75); /*GPIO3_11*/
+
+	return 0;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	u32 index;
+	s32 status = 0;
+
+	for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) {
+		switch (index) {
+		case 0:
+			mxc_request_iomux(MX53_PIN_SD1_CMD, IOMUX_CONFIG_ALT0);
+			mxc_request_iomux(MX53_PIN_SD1_CLK, IOMUX_CONFIG_ALT0);
+			mxc_request_iomux(MX53_PIN_SD1_DATA0,
+						IOMUX_CONFIG_ALT0);
+			mxc_request_iomux(MX53_PIN_SD1_DATA1,
+						IOMUX_CONFIG_ALT0);
+			mxc_request_iomux(MX53_PIN_SD1_DATA2,
+						IOMUX_CONFIG_ALT0);
+			mxc_request_iomux(MX53_PIN_SD1_DATA3,
+						IOMUX_CONFIG_ALT0);
+			mxc_request_iomux(MX53_PIN_EIM_DA13,
+						IOMUX_CONFIG_ALT1);
+
+			mxc_iomux_set_pad(MX53_PIN_SD1_CMD,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU);
+			mxc_iomux_set_pad(MX53_PIN_SD1_CLK,
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU |
+				PAD_CTL_DRV_HIGH);
+			mxc_iomux_set_pad(MX53_PIN_SD1_DATA0,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_SD1_DATA1,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_SD1_DATA2,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_SD1_DATA3,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			break;
+		case 1:
+			mxc_request_iomux(MX53_PIN_ATA_RESET_B,
+						IOMUX_CONFIG_ALT2);
+			mxc_request_iomux(MX53_PIN_ATA_IORDY,
+						IOMUX_CONFIG_ALT2);
+			mxc_request_iomux(MX53_PIN_ATA_DATA8,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA9,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA10,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA11,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA0,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA1,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA2,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA3,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_EIM_DA11,
+						IOMUX_CONFIG_ALT1);
+
+			mxc_iomux_set_pad(MX53_PIN_ATA_RESET_B,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_IORDY,
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU |
+				PAD_CTL_DRV_HIGH);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA8,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA9,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA10,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA11,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA0,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA1,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA2,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA3,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+
+			break;
+		default:
+			printf("Warning: you configured more ESDHC controller"
+				"(%d) as supported by the board(2)\n",
+				CONFIG_SYS_FSL_ESDHC_NUM);
+			return status;
+		}
+		status |= fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
+	}
+
+	return status;
+}
+#endif
+
+static void setup_i2c(unsigned int port_number)
+{
+	switch (port_number) {
+	case 0:
+		/* i2c1 SDA */
+		mxc_request_iomux(MX53_PIN_CSI0_D8,
+				IOMUX_CONFIG_ALT5 | IOMUX_CONFIG_SION);
+		mxc_iomux_set_input(MX53_I2C1_IPP_SDA_IN_SELECT_INPUT,
+				INPUT_CTL_PATH0);
+		mxc_iomux_set_pad(MX53_PIN_CSI0_D8,
+				PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH |
+				PAD_CTL_100K_PU | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_PUE_PULL |
+				PAD_CTL_ODE_OPENDRAIN_ENABLE);
+		/* i2c1 SCL */
+		mxc_request_iomux(MX53_PIN_CSI0_D9,
+				IOMUX_CONFIG_ALT5 | IOMUX_CONFIG_SION);
+		mxc_iomux_set_input(MX53_I2C1_IPP_SCL_IN_SELECT_INPUT,
+				INPUT_CTL_PATH0);
+		mxc_iomux_set_pad(MX53_PIN_CSI0_D9,
+				PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH |
+				PAD_CTL_100K_PU | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_PUE_PULL |
+				PAD_CTL_ODE_OPENDRAIN_ENABLE);
+		break;
+	case 1:
+		/* i2c2 SDA */
+		mxc_request_iomux(MX53_PIN_KEY_ROW3,
+				IOMUX_CONFIG_ALT4 | IOMUX_CONFIG_SION);
+		mxc_iomux_set_input(MX53_I2C2_IPP_SDA_IN_SELECT_INPUT,
+				INPUT_CTL_PATH0);
+		mxc_iomux_set_pad(MX53_PIN_KEY_ROW3,
+				PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH |
+				PAD_CTL_100K_PU | PAD_CTL_HYS_ENABLE |
+				PAD_CTL_ODE_OPENDRAIN_ENABLE);
+
+		/* i2c2 SCL */
+		mxc_request_iomux(MX53_PIN_KEY_COL3,
+				IOMUX_CONFIG_ALT4 | IOMUX_CONFIG_SION);
+		mxc_iomux_set_input(MX53_I2C2_IPP_SCL_IN_SELECT_INPUT,
+				INPUT_CTL_PATH0);
+		mxc_iomux_set_pad(MX53_PIN_KEY_COL3,
+				PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH |
+				PAD_CTL_100K_PU | PAD_CTL_HYS_ENABLE |
+				PAD_CTL_ODE_OPENDRAIN_ENABLE);
+		break;
+	default:
+		printf("Warning: Wrong I2C port number\n");
+		break;
+	}
+}
+
+static void clock_init(void)
+{
+	int ret;
+	u32 ref_clk = CONFIG_SYS_MX5_HCLK;
+	/*
+	 * After increase voltage to 1.25V, We can switch
+	 * CPU clokc to 1Ghz and DDR to 400Mhz safely now
+	 */
+	ret = mxc_set_clock(ref_clk, 1000, MXC_ARM_CLK);
+	if (!ret)
+		printf("CPU:   Switch CPU clock to 1GHZ OK\n");
+	else
+		printf("CPU:   Switch CPU clock to 1GHZ failed\n");
+
+	ret = mxc_set_clock(ref_clk, 400, MXC_PERIPH_CLK);
+	ret |= mxc_set_clock(ref_clk, 400, MXC_DDR_CLK);
+	if (!ret)
+		printf("DDR:   Switch DDR clock to 400MHz OK\n");
+	else
+		printf("CPU:   Switch DDR clock to 1GHZ failed\n");
+}
+
+static void power_init(void)
+{
+	unsigned int val;
+
+	/* Set VDDA to 1.25V */
+	val = DA9052_BUCKCORE_BCOREEN;
+	val |= DA_BUCKCORE_VBCORE_1_250V;
+	pmic_reg_write(DA9053_BUCKCORE_REG, val);
+	val = pmic_reg_read(DA9053_SUPPLY_REG);
+	val |= DA9052_SUPPLY_VBCOREGO;
+	pmic_reg_write(DA9053_SUPPLY_REG, val);
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+	setup_iomux_fec();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	gd->bd->bi_arch_number = MACH_TYPE_MX53_LOCO;
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+#ifdef CONFIG_I2C_MXC
+	setup_i2c(0);
+	power_init();
+	clock_init();
+#endif
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: MX53 LOCO\n");
+
+	return 0;
+}
diff --git a/boards.cfg b/boards.cfg
index 55c21f2..4d1b211 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -110,6 +110,7 @@  ca9x4_ct_vxp                 arm         armv7       vexpress            armltd
 efikamx                      arm         armv7       efikamx             -              mx5
 mx51evk                      arm         armv7       mx51evk             freescale      mx5		mx51evk:IMX_CONFIG=board/freescale/mx51evk/imximage.cfg
 mx53evk                      arm         armv7       mx53evk             freescale      mx5		mx53evk:IMX_CONFIG=board/freescale/mx53evk/imximage.cfg
+mx53loco                     arm         armv7       mx53loco            freescale      mx5		mx53loco:IMX_CONFIG=board/freescale/mx53loco/imximage.cfg
 vision2                      arm         armv7       vision2             ttcontrol      mx5
 cm_t35                       arm         armv7       cm_t35              -              omap3
 omap3_overo                  arm         armv7       overo               -              omap3
diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h
new file mode 100644
index 0000000..11df9b8
--- /dev/null
+++ b/include/configs/mx53loco.h
@@ -0,0 +1,198 @@ 
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Jason Liu <r64343@freescale.com>
+ *
+ * Configuration settings for Freescale MX53 low cost board.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MX53
+
+#define CONFIG_SYS_MX5_HCLK	24000000
+#define CONFIG_SYS_MX5_CLK32		32768
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_L2_OFF
+
+#include <asm/arch/imx-regs.h>
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2 * 1024 * 1024)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_MXC_UART
+#define CONFIG_SYS_MX53_UART1
+
+/* I2C Configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_HARD_I2C
+#define CONFIG_I2C_MXC
+#define CONFIG_SYS_I2C_MX53_PORT1
+#define CONFIG_SYS_I2C_SPEED            100000
+#define CONFIG_SYS_I2C_SLAVE            0xfe
+
+/* PMIC Configs */
+#define CONFIG_DIALOG_PMIC
+#define CONFIG_SYS_DIALOG_PMIC_I2C_ADDR    0x48
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+#define CONFIG_SYS_FSL_ESDHC_NUM	2
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+/* Eth Configs */
+#define CONFIG_HAS_ETH1
+#define CONFIG_NET_MULTI
+#define CONFIG_MII
+#define CONFIG_DISCOVER_PHY
+
+#define CONFIG_FEC_MXC
+#define IMX_FEC_BASE	FEC_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR	0x1F
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{9600, 19200, 38400, 57600, 115200}
+
+/* Command definition */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_BOOTDELAY	3
+
+#define CONFIG_PRIME	"FEC0"
+
+#define CONFIG_LOADADDR		0x70800000	/* loadaddr env var */
+#define CONFIG_SYS_TEXT_BASE    0x77800000
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"uimage=uImage\0" \
+	"mmcdev=0\0" \
+	"mmcpart=2\0" \
+	"mmcroot=/dev/mmcblk0p3 rw\0" \
+	"mmcrootfstype=ext3 rootwait\0" \
+	"mmcargs=setenv bootargs console=ttymxc0,${baudrate} " \
+		"root=${mmcroot} " \
+		"rootfstype=${mmcrootfstype}\0" \
+	"loadbootscript=" \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"bootm\0" \
+	"netargs=setenv bootargs console=ttymxc0,${baudrate} " \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+	"netboot=echo Booting from net ...; " \
+		"run netargs; " \
+		"dhcp ${uimage}; bootm\0" \
+
+#define CONFIG_BOOTCOMMAND \
+	"if mmc rescan ${mmcdev}; then " \
+		"if run loadbootscript; then " \
+			"run bootscript; " \
+		"else " \
+			"if run loaduimage; then " \
+				"run mmcboot; " \
+			"else run netboot; " \
+			"fi; " \
+		"fi; " \
+	"else run netboot; fi"
+
+#define CONFIG_ARP_TIMEOUT	200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_PROMPT		"MX53LOCO U-Boot > "
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START       0x70000000
+#define CONFIG_SYS_MEMTEST_END         0x70010000
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+
+#define CONFIG_SYS_HZ		1000
+#define CONFIG_CMDLINE_EDITING
+
+/* Stack sizes */
+#define CONFIG_STACKSIZE	(128 * 1024)	/* regular stack */
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS	2
+#define PHYS_SDRAM_1		CSD0_BASE_ADDR
+#define PHYS_SDRAM_1_SIZE	(512 * 1024 * 1024)
+#define PHYS_SDRAM_2		CSD1_BASE_ADDR
+#define PHYS_SDRAM_2_SIZE	(512 * 1024 * 1024)
+#define PHYS_SDRAM_SIZE         (PHYS_SDRAM_1_SIZE + PHYS_SDRAM_2_SIZE)
+
+#define CONFIG_SYS_SDRAM_BASE		(PHYS_SDRAM_1)
+#define CONFIG_SYS_INIT_RAM_ADDR	(IRAM_BASE_ADDR)
+#define CONFIG_SYS_INIT_RAM_SIZE	(IRAM_SIZE)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_OFFSET      (6 * 64 * 1024)
+#define CONFIG_ENV_SIZE        (8 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_SYS_BOOTMAPSZ   0x800000
+
+#endif				/* __CONFIG_H */