deleted file mode 100644
@@ -1,470 +0,0 @@
-/** @file
- Serial I/O Port library functions with no library constructor/destructor
-
- Copyright (c) 2008 - 2010, Apple Inc. All rights reserved.<BR>
- Copyright (c) 2011 - 2016, ARM Ltd. All rights reserved.<BR>
-
- This program and the accompanying materials
- are licensed and made available under the terms and conditions of the BSD License
- which accompanies this distribution. The full text of the license may be found at
- http://opensource.org/licenses/bsd-license.php
-
- THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
- WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
-
-**/
-
-#include <Library/DebugLib.h>
-#include <Library/IoLib.h>
-#include <Library/PcdLib.h>
-
-#include <Drivers/PL011Uart.h>
-
-#define FRACTION_PART_SIZE_IN_BITS 6
-#define FRACTION_PART_MASK ((1 << FRACTION_PART_SIZE_IN_BITS) - 1)
-
-//
-// EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE is the only
-// control bit that is not supported.
-//
-STATIC CONST UINT32 mInvalidControlBits = EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE;
-
-/**
-
- Initialise the serial port to the specified settings.
- The serial port is re-configured only if the specified settings
- are different from the current settings.
- All unspecified settings will be set to the default values.
-
- @param UartBase The base address of the serial device.
- @param UartClkInHz The clock in Hz for the serial device.
- Ignored if the PCD PL011UartInteger is not 0
- @param BaudRate The baud rate of the serial device. If the
- baud rate is not supported, the speed will be
- reduced to the nearest supported one and the
- variable's value will be updated accordingly.
- @param ReceiveFifoDepth The number of characters the device will
- buffer on input. Value of 0 will use the
- device's default FIFO depth.
- @param Parity If applicable, this is the EFI_PARITY_TYPE
- that is computed or checked as each character
- is transmitted or received. If the device
- does not support parity, the value is the
- default parity value.
- @param DataBits The number of data bits in each character.
- @param StopBits If applicable, the EFI_STOP_BITS_TYPE number
- of stop bits per character.
- If the device does not support stop bits, the
- value is the default stop bit value.
-
- @retval RETURN_SUCCESS All attributes were set correctly on the
- serial device.
- @retval RETURN_INVALID_PARAMETER One or more of the attributes has an
- unsupported value.
-
-**/
-RETURN_STATUS
-EFIAPI
-PL011UartInitializePort (
- IN UINTN UartBase,
- IN UINT32 UartClkInHz,
- IN OUT UINT64 *BaudRate,
- IN OUT UINT32 *ReceiveFifoDepth,
- IN OUT EFI_PARITY_TYPE *Parity,
- IN OUT UINT8 *DataBits,
- IN OUT EFI_STOP_BITS_TYPE *StopBits
- )
-{
- UINT32 LineControl;
- UINT32 Divisor;
- UINT32 Integer;
- UINT32 Fractional;
- UINT32 HardwareFifoDepth;
-
- HardwareFifoDepth = (PL011_UARTPID2_VER (MmioRead32 (UartBase + UARTPID2)) \
- > PL011_VER_R1P4) \
- ? 32 : 16 ;
- // The PL011 supports a buffer of 1, 16 or 32 chars. Therefore we can accept
- // 1 char buffer as the minimum FIFO size. Because everything can be rounded
- // down, there is no maximum FIFO size.
- if ((*ReceiveFifoDepth == 0) || (*ReceiveFifoDepth >= HardwareFifoDepth)) {
- // Enable FIFO
- LineControl = PL011_UARTLCR_H_FEN;
- *ReceiveFifoDepth = HardwareFifoDepth;
- } else {
- // Disable FIFO
- LineControl = 0;
- // Nothing else to do. 1 byte FIFO is default.
- *ReceiveFifoDepth = 1;
- }
-
- //
- // Parity
- //
- switch (*Parity) {
- case DefaultParity:
- *Parity = NoParity;
- case NoParity:
- // Nothing to do. Parity is disabled by default.
- break;
- case EvenParity:
- LineControl |= (PL011_UARTLCR_H_PEN | PL011_UARTLCR_H_EPS);
- break;
- case OddParity:
- LineControl |= PL011_UARTLCR_H_PEN;
- break;
- case MarkParity:
- LineControl |= ( PL011_UARTLCR_H_PEN \
- | PL011_UARTLCR_H_SPS \
- | PL011_UARTLCR_H_EPS);
- break;
- case SpaceParity:
- LineControl |= (PL011_UARTLCR_H_PEN | PL011_UARTLCR_H_SPS);
- break;
- default:
- return RETURN_INVALID_PARAMETER;
- }
-
- //
- // Data Bits
- //
- switch (*DataBits) {
- case 0:
- *DataBits = 8;
- case 8:
- LineControl |= PL011_UARTLCR_H_WLEN_8;
- break;
- case 7:
- LineControl |= PL011_UARTLCR_H_WLEN_7;
- break;
- case 6:
- LineControl |= PL011_UARTLCR_H_WLEN_6;
- break;
- case 5:
- LineControl |= PL011_UARTLCR_H_WLEN_5;
- break;
- default:
- return RETURN_INVALID_PARAMETER;
- }
-
- //
- // Stop Bits
- //
- switch (*StopBits) {
- case DefaultStopBits:
- *StopBits = OneStopBit;
- case OneStopBit:
- // Nothing to do. One stop bit is enabled by default.
- break;
- case TwoStopBits:
- LineControl |= PL011_UARTLCR_H_STP2;
- break;
- case OneFiveStopBits:
- // Only 1 or 2 stop bits are supported
- default:
- return RETURN_INVALID_PARAMETER;
- }
-
- // Don't send the LineControl value to the PL011 yet,
- // wait until after the Baud Rate setting.
- // This ensures we do not mess up the UART settings halfway through
- // in the rare case when there is an error with the Baud Rate.
-
- //
- // Baud Rate
- //
-
- // If PL011 Integer value has been defined then always ignore the BAUD rate
- if (FixedPcdGet32 (PL011UartInteger) != 0) {
- Integer = FixedPcdGet32 (PL011UartInteger);
- Fractional = FixedPcdGet32 (PL011UartFractional);
- } else {
- // If BAUD rate is zero then replace it with the system default value
- if (*BaudRate == 0) {
- *BaudRate = FixedPcdGet32 (PcdSerialBaudRate);
- if (*BaudRate == 0) {
- return RETURN_INVALID_PARAMETER;
- }
- }
- if (0 == UartClkInHz) {
- return RETURN_INVALID_PARAMETER;
- }
-
- Divisor = (UartClkInHz * 4) / *BaudRate;
- Integer = Divisor >> FRACTION_PART_SIZE_IN_BITS;
- Fractional = Divisor & FRACTION_PART_MASK;
- }
-
- //
- // If PL011 is already initialized, check the current settings
- // and re-initialize only if the settings are different.
- //
- if (((MmioRead32 (UartBase + UARTCR) & PL011_UARTCR_UARTEN) != 0) &&
- (MmioRead32 (UartBase + UARTLCR_H) == LineControl) &&
- (MmioRead32 (UartBase + UARTIBRD) == Integer) &&
- (MmioRead32 (UartBase + UARTFBRD) == Fractional)) {
- // Nothing to do - already initialized with correct attributes
- return RETURN_SUCCESS;
- }
-
- // Wait for the end of transmission
- while ((MmioRead32 (UartBase + UARTFR) & PL011_UARTFR_TXFE) == 0);
-
- // Disable UART: "The UARTLCR_H, UARTIBRD, and UARTFBRD registers must not be changed
- // when the UART is enabled"
- MmioWrite32 (UartBase + UARTCR, 0);
-
- // Set Baud Rate Registers
- MmioWrite32 (UartBase + UARTIBRD, Integer);
- MmioWrite32 (UartBase + UARTFBRD, Fractional);
-
- // No parity, 1 stop, no fifo, 8 data bits
- MmioWrite32 (UartBase + UARTLCR_H, LineControl);
-
- // Clear any pending errors
- MmioWrite32 (UartBase + UARTECR, 0);
-
- // Enable Tx, Rx, and UART overall
- MmioWrite32 (UartBase + UARTCR,
- PL011_UARTCR_RXE | PL011_UARTCR_TXE | PL011_UARTCR_UARTEN);
-
- return RETURN_SUCCESS;
-}
-
-/**
-
- Assert or deassert the control signals on a serial port.
- The following control signals are set according their bit settings :
- . Request to Send
- . Data Terminal Ready
-
- @param[in] UartBase UART registers base address
- @param[in] Control The following bits are taken into account :
- . EFI_SERIAL_REQUEST_TO_SEND : assert/deassert the
- "Request To Send" control signal if this bit is
- equal to one/zero.
- . EFI_SERIAL_DATA_TERMINAL_READY : assert/deassert
- the "Data Terminal Ready" control signal if this
- bit is equal to one/zero.
- . EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : enable/disable
- the hardware loopback if this bit is equal to
- one/zero.
- . EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : not supported.
- . EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : enable/
- disable the hardware flow control based on CTS (Clear
- To Send) and RTS (Ready To Send) control signals.
-
- @retval RETURN_SUCCESS The new control bits were set on the device.
- @retval RETURN_UNSUPPORTED The device does not support this operation.
-
-**/
-RETURN_STATUS
-EFIAPI
-PL011UartSetControl (
- IN UINTN UartBase,
- IN UINT32 Control
- )
-{
- UINT32 Bits;
-
- if (Control & (mInvalidControlBits)) {
- return RETURN_UNSUPPORTED;
- }
-
- Bits = MmioRead32 (UartBase + UARTCR);
-
- if (Control & EFI_SERIAL_REQUEST_TO_SEND) {
- Bits |= PL011_UARTCR_RTS;
- } else {
- Bits &= ~PL011_UARTCR_RTS;
- }
-
- if (Control & EFI_SERIAL_DATA_TERMINAL_READY) {
- Bits |= PL011_UARTCR_DTR;
- } else {
- Bits &= ~PL011_UARTCR_DTR;
- }
-
- if (Control & EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE) {
- Bits |= PL011_UARTCR_LBE;
- } else {
- Bits &= ~PL011_UARTCR_LBE;
- }
-
- if (Control & EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE) {
- Bits |= (PL011_UARTCR_CTSEN | PL011_UARTCR_RTSEN);
- } else {
- Bits &= ~(PL011_UARTCR_CTSEN | PL011_UARTCR_RTSEN);
- }
-
- MmioWrite32 (UartBase + UARTCR, Bits);
-
- return RETURN_SUCCESS;
-}
-
-/**
-
- Retrieve the status of the control bits on a serial device.
-
- @param[in] UartBase UART registers base address
- @param[out] Control Status of the control bits on a serial device :
-
- . EFI_SERIAL_DATA_CLEAR_TO_SEND,
- EFI_SERIAL_DATA_SET_READY,
- EFI_SERIAL_RING_INDICATE,
- EFI_SERIAL_CARRIER_DETECT,
- EFI_SERIAL_REQUEST_TO_SEND,
- EFI_SERIAL_DATA_TERMINAL_READY
- are all related to the DTE (Data Terminal Equipment)
- and DCE (Data Communication Equipment) modes of
- operation of the serial device.
- . EFI_SERIAL_INPUT_BUFFER_EMPTY : equal to one if the
- receive buffer is empty, 0 otherwise.
- . EFI_SERIAL_OUTPUT_BUFFER_EMPTY : equal to one if the
- transmit buffer is empty, 0 otherwise.
- . EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : equal to one if
- the hardware loopback is enabled (the ouput feeds the
- receive buffer), 0 otherwise.
- . EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : equal to one if
- a loopback is accomplished by software, 0 otherwise.
- . EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : equal to
- one if the hardware flow control based on CTS (Clear
- To Send) and RTS (Ready To Send) control signals is
- enabled, 0 otherwise.
-
- @retval RETURN_SUCCESS The control bits were read from the serial device.
-
-**/
-RETURN_STATUS
-EFIAPI
-PL011UartGetControl (
- IN UINTN UartBase,
- OUT UINT32 *Control
- )
-{
- UINT32 FlagRegister;
- UINT32 ControlRegister;
-
-
- FlagRegister = MmioRead32 (UartBase + UARTFR);
- ControlRegister = MmioRead32 (UartBase + UARTCR);
-
- *Control = 0;
-
- if ((FlagRegister & PL011_UARTFR_CTS) == PL011_UARTFR_CTS) {
- *Control |= EFI_SERIAL_CLEAR_TO_SEND;
- }
-
- if ((FlagRegister & PL011_UARTFR_DSR) == PL011_UARTFR_DSR) {
- *Control |= EFI_SERIAL_DATA_SET_READY;
- }
-
- if ((FlagRegister & PL011_UARTFR_RI) == PL011_UARTFR_RI) {
- *Control |= EFI_SERIAL_RING_INDICATE;
- }
-
- if ((FlagRegister & PL011_UARTFR_DCD) == PL011_UARTFR_DCD) {
- *Control |= EFI_SERIAL_CARRIER_DETECT;
- }
-
- if ((ControlRegister & PL011_UARTCR_RTS) == PL011_UARTCR_RTS) {
- *Control |= EFI_SERIAL_REQUEST_TO_SEND;
- }
-
- if ((ControlRegister & PL011_UARTCR_DTR) == PL011_UARTCR_DTR) {
- *Control |= EFI_SERIAL_DATA_TERMINAL_READY;
- }
-
- if ((FlagRegister & PL011_UARTFR_RXFE) == PL011_UARTFR_RXFE) {
- *Control |= EFI_SERIAL_INPUT_BUFFER_EMPTY;
- }
-
- if ((FlagRegister & PL011_UARTFR_TXFE) == PL011_UARTFR_TXFE) {
- *Control |= EFI_SERIAL_OUTPUT_BUFFER_EMPTY;
- }
-
- if ((ControlRegister & (PL011_UARTCR_CTSEN | PL011_UARTCR_RTSEN))
- == (PL011_UARTCR_CTSEN | PL011_UARTCR_RTSEN)) {
- *Control |= EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE;
- }
-
- if ((ControlRegister & PL011_UARTCR_LBE) == PL011_UARTCR_LBE) {
- *Control |= EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE;
- }
-
- return RETURN_SUCCESS;
-}
-
-/**
- Write data to serial device.
-
- @param Buffer Point of data buffer which need to be written.
- @param NumberOfBytes Number of output bytes which are cached in Buffer.
-
- @retval 0 Write data failed.
- @retval !0 Actual number of bytes written to serial device.
-
-**/
-UINTN
-EFIAPI
-PL011UartWrite (
- IN UINTN UartBase,
- IN UINT8 *Buffer,
- IN UINTN NumberOfBytes
- )
-{
- UINT8* CONST Final = &Buffer[NumberOfBytes];
-
- while (Buffer < Final) {
- // Wait until UART able to accept another char
- while ((MmioRead32 (UartBase + UARTFR) & UART_TX_FULL_FLAG_MASK));
-
- MmioWrite8 (UartBase + UARTDR, *Buffer++);
- }
-
- return NumberOfBytes;
-}
-
-/**
- Read data from serial device and save the data in buffer.
-
- @param Buffer Point of data buffer which need to be written.
- @param NumberOfBytes Number of output bytes which are cached in Buffer.
-
- @retval 0 Read data failed.
- @retval !0 Actual number of bytes read from serial device.
-
-**/
-UINTN
-EFIAPI
-PL011UartRead (
- IN UINTN UartBase,
- OUT UINT8 *Buffer,
- IN UINTN NumberOfBytes
- )
-{
- UINTN Count;
-
- for (Count = 0; Count < NumberOfBytes; Count++, Buffer++) {
- while ((MmioRead32 (UartBase + UARTFR) & UART_RX_EMPTY_FLAG_MASK) != 0);
- *Buffer = MmioRead8 (UartBase + UARTDR);
- }
-
- return NumberOfBytes;
-}
-
-/**
- Check to see if any data is available to be read from the debug device.
-
- @retval TRUE At least one byte of data is available to be read
- @retval FALSE No data is available to be read
-
-**/
-BOOLEAN
-EFIAPI
-PL011UartPoll (
- IN UINTN UartBase
- )
-{
- return ((MmioRead32 (UartBase + UARTFR) & UART_RX_EMPTY_FLAG_MASK) == 0);
-}
deleted file mode 100644
@@ -1,42 +0,0 @@
-#/** @file
-#
-# Component description file for PL011Uart module
-#
-# Copyright (c) 2011-2016, ARM Ltd. All rights reserved.<BR>
-#
-# This program and the accompanying materials
-# are licensed and made available under the terms and conditions of the BSD License
-# which accompanies this distribution. The full text of the license may be found at
-# http://opensource.org/licenses/bsd-license.php
-#
-# THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
-# WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
-#
-#**/
-
-[Defines]
- INF_VERSION = 0x00010005
- BASE_NAME = PL011Uart
- FILE_GUID = 4ec8b120-8307-11e0-bc91-0002a5d5c51b
- MODULE_TYPE = BASE
- VERSION_STRING = 1.0
- LIBRARY_CLASS = PL011UartLib
-
-[Sources.common]
- PL011Uart.c
-
-[LibraryClasses]
- DebugLib
- IoLib
-
-[Packages]
- MdePkg/MdePkg.dec
- MdeModulePkg/MdeModulePkg.dec
- ArmPlatformPkg/ArmPlatformPkg.dec
-
-[FixedPcd]
- gEfiMdeModulePkgTokenSpaceGuid.PcdSerialBaudRate
-
- gArmPlatformTokenSpaceGuid.PL011UartInteger
- gArmPlatformTokenSpaceGuid.PL011UartFractional
- gArmPlatformTokenSpaceGuid.PL011UartRegOffsetVariant
deleted file mode 100644
@@ -1,290 +0,0 @@
-/** @file
-*
-* Copyright (c) 2011-2016, ARM Limited. All rights reserved.
-*
-* This program and the accompanying materials
-* are licensed and made available under the terms and conditions of the BSD License
-* which accompanies this distribution. The full text of the license may be found at
-* http://opensource.org/licenses/bsd-license.php
-*
-* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
-* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
-*
-**/
-
-#ifndef __PL011_UART_H__
-#define __PL011_UART_H__
-
-#include <Uefi.h>
-#include <Protocol/SerialIo.h>
-
-#define PL011_VARIANT_ZTE 1
-
-// PL011 Registers
-#if FixedPcdGet8 (PL011UartRegOffsetVariant) == PL011_VARIANT_ZTE
-#define UARTDR 0x004
-#define UARTRSR 0x010
-#define UARTECR 0x010
-#define UARTFR 0x014
-#define UARTIBRD 0x024
-#define UARTFBRD 0x028
-#define UARTLCR_H 0x030
-#define UARTCR 0x034
-#define UARTIFLS 0x038
-#define UARTIMSC 0x040
-#define UARTRIS 0x044
-#define UARTMIS 0x048
-#define UARTICR 0x04c
-#define UARTDMACR 0x050
-#else
-#define UARTDR 0x000
-#define UARTRSR 0x004
-#define UARTECR 0x004
-#define UARTFR 0x018
-#define UARTILPR 0x020
-#define UARTIBRD 0x024
-#define UARTFBRD 0x028
-#define UARTLCR_H 0x02C
-#define UARTCR 0x030
-#define UARTIFLS 0x034
-#define UARTIMSC 0x038
-#define UARTRIS 0x03C
-#define UARTMIS 0x040
-#define UARTICR 0x044
-#define UARTDMACR 0x048
-#endif
-
-#define UARTPID0 0xFE0
-#define UARTPID1 0xFE4
-#define UARTPID2 0xFE8
-#define UARTPID3 0xFEC
-
-// Data status bits
-#define UART_DATA_ERROR_MASK 0x0F00
-
-// Status reg bits
-#define UART_STATUS_ERROR_MASK 0x0F
-
-// Flag reg bits
-#if FixedPcdGet8 (PL011UartRegOffsetVariant) == PL011_VARIANT_ZTE
-#define PL011_UARTFR_RI (1 << 0) // Ring indicator
-#define PL011_UARTFR_TXFE (1 << 7) // Transmit FIFO empty
-#define PL011_UARTFR_RXFF (1 << 6) // Receive FIFO full
-#define PL011_UARTFR_TXFF (1 << 5) // Transmit FIFO full
-#define PL011_UARTFR_RXFE (1 << 4) // Receive FIFO empty
-#define PL011_UARTFR_BUSY (1 << 8) // UART busy
-#define PL011_UARTFR_DCD (1 << 2) // Data carrier detect
-#define PL011_UARTFR_DSR (1 << 3) // Data set ready
-#define PL011_UARTFR_CTS (1 << 1) // Clear to send
-#else
-#define PL011_UARTFR_RI (1 << 8) // Ring indicator
-#define PL011_UARTFR_TXFE (1 << 7) // Transmit FIFO empty
-#define PL011_UARTFR_RXFF (1 << 6) // Receive FIFO full
-#define PL011_UARTFR_TXFF (1 << 5) // Transmit FIFO full
-#define PL011_UARTFR_RXFE (1 << 4) // Receive FIFO empty
-#define PL011_UARTFR_BUSY (1 << 3) // UART busy
-#define PL011_UARTFR_DCD (1 << 2) // Data carrier detect
-#define PL011_UARTFR_DSR (1 << 1) // Data set ready
-#define PL011_UARTFR_CTS (1 << 0) // Clear to send
-#endif
-
-// Flag reg bits - alternative names
-#define UART_TX_EMPTY_FLAG_MASK PL011_UARTFR_TXFE
-#define UART_RX_FULL_FLAG_MASK PL011_UARTFR_RXFF
-#define UART_TX_FULL_FLAG_MASK PL011_UARTFR_TXFF
-#define UART_RX_EMPTY_FLAG_MASK PL011_UARTFR_RXFE
-#define UART_BUSY_FLAG_MASK PL011_UARTFR_BUSY
-
-// Control reg bits
-#define PL011_UARTCR_CTSEN (1 << 15) // CTS hardware flow control enable
-#define PL011_UARTCR_RTSEN (1 << 14) // RTS hardware flow control enable
-#define PL011_UARTCR_RTS (1 << 11) // Request to send
-#define PL011_UARTCR_DTR (1 << 10) // Data transmit ready.
-#define PL011_UARTCR_RXE (1 << 9) // Receive enable
-#define PL011_UARTCR_TXE (1 << 8) // Transmit enable
-#define PL011_UARTCR_LBE (1 << 7) // Loopback enable
-#define PL011_UARTCR_UARTEN (1 << 0) // UART Enable
-
-// Line Control Register Bits
-#define PL011_UARTLCR_H_SPS (1 << 7) // Stick parity select
-#define PL011_UARTLCR_H_WLEN_8 (3 << 5)
-#define PL011_UARTLCR_H_WLEN_7 (2 << 5)
-#define PL011_UARTLCR_H_WLEN_6 (1 << 5)
-#define PL011_UARTLCR_H_WLEN_5 (0 << 5)
-#define PL011_UARTLCR_H_FEN (1 << 4) // FIFOs Enable
-#define PL011_UARTLCR_H_STP2 (1 << 3) // Two stop bits select
-#define PL011_UARTLCR_H_EPS (1 << 2) // Even parity select
-#define PL011_UARTLCR_H_PEN (1 << 1) // Parity Enable
-#define PL011_UARTLCR_H_BRK (1 << 0) // Send break
-
-#define PL011_UARTPID2_VER(X) (((X) >> 4) & 0xF)
-#define PL011_VER_R1P4 0x2
-
-/**
-
- Initialise the serial port to the specified settings.
- All unspecified settings will be set to the default values.
-
- @param[in] UartBase The base address of the serial device.
- @param[in] UartClkInHz The clock in Hz for the serial device.
- Ignored if the PCD PL011UartInteger is not 0
- @param[in out] BaudRate The baud rate of the serial device. If the
- baud rate is not supported, the speed will be
- reduced to the nearest supported one and the
- variable's value will be updated accordingly.
- @param[in out] ReceiveFifoDepth The number of characters the device will
- buffer on input. Value of 0 will use the
- device's default FIFO depth.
- @param[in out] Parity If applicable, this is the EFI_PARITY_TYPE
- that is computed or checked as each character
- is transmitted or received. If the device
- does not support parity, the value is the
- default parity value.
- @param[in out] DataBits The number of data bits in each character.
- @param[in out] StopBits If applicable, the EFI_STOP_BITS_TYPE number
- of stop bits per character.
- If the device does not support stop bits, the
- value is the default stop bit value.
-
- @retval RETURN_SUCCESS All attributes were set correctly on the
- serial device.
- @retval RETURN_INVALID_PARAMETER One or more of the attributes has an
- unsupported value.
-
-**/
-RETURN_STATUS
-EFIAPI
-PL011UartInitializePort (
- IN UINTN UartBase,
- IN UINT32 UartClkInHz,
- IN OUT UINT64 *BaudRate,
- IN OUT UINT32 *ReceiveFifoDepth,
- IN OUT EFI_PARITY_TYPE *Parity,
- IN OUT UINT8 *DataBits,
- IN OUT EFI_STOP_BITS_TYPE *StopBits
- );
-
-/**
-
- Assert or deassert the control signals on a serial port.
- The following control signals are set according their bit settings :
- . Request to Send
- . Data Terminal Ready
-
- @param[in] UartBase UART registers base address
- @param[in] Control The following bits are taken into account :
- . EFI_SERIAL_REQUEST_TO_SEND : assert/deassert the
- "Request To Send" control signal if this bit is
- equal to one/zero.
- . EFI_SERIAL_DATA_TERMINAL_READY : assert/deassert
- the "Data Terminal Ready" control signal if this
- bit is equal to one/zero.
- . EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : enable/disable
- the hardware loopback if this bit is equal to
- one/zero.
- . EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : not supported.
- . EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : enable/
- disable the hardware flow control based on CTS (Clear
- To Send) and RTS (Ready To Send) control signals.
-
- @retval RETURN_SUCCESS The new control bits were set on the device.
- @retval RETURN_UNSUPPORTED The device does not support this operation.
-
-**/
-RETURN_STATUS
-EFIAPI
-PL011UartSetControl (
- IN UINTN UartBase,
- IN UINT32 Control
- );
-
-/**
-
- Retrieve the status of the control bits on a serial device.
-
- @param[in] UartBase UART registers base address
- @param[out] Control Status of the control bits on a serial device :
-
- . EFI_SERIAL_DATA_CLEAR_TO_SEND,
- EFI_SERIAL_DATA_SET_READY,
- EFI_SERIAL_RING_INDICATE,
- EFI_SERIAL_CARRIER_DETECT,
- EFI_SERIAL_REQUEST_TO_SEND,
- EFI_SERIAL_DATA_TERMINAL_READY
- are all related to the DTE (Data Terminal Equipment)
- and DCE (Data Communication Equipment) modes of
- operation of the serial device.
- . EFI_SERIAL_INPUT_BUFFER_EMPTY : equal to one if the
- receive buffer is empty, 0 otherwise.
- . EFI_SERIAL_OUTPUT_BUFFER_EMPTY : equal to one if the
- transmit buffer is empty, 0 otherwise.
- . EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : equal to one if
- the hardware loopback is enabled (the ouput feeds the
- receive buffer), 0 otherwise.
- . EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : equal to one if
- a loopback is accomplished by software, 0 otherwise.
- . EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : equal to
- one if the hardware flow control based on CTS (Clear
- To Send) and RTS (Ready To Send) control signals is
- enabled, 0 otherwise.
-
- @retval RETURN_SUCCESS The control bits were read from the serial device.
-
-**/
-RETURN_STATUS
-EFIAPI
-PL011UartGetControl (
- IN UINTN UartBase,
- OUT UINT32 *Control
- );
-
-/**
- Write data to serial device.
-
- @param Buffer Point of data buffer which need to be written.
- @param NumberOfBytes Number of output bytes which are cached in Buffer.
-
- @retval 0 Write data failed.
- @retval !0 Actual number of bytes written to serial device.
-
-**/
-UINTN
-EFIAPI
-PL011UartWrite (
- IN UINTN UartBase,
- IN UINT8 *Buffer,
- IN UINTN NumberOfBytes
- );
-
-/**
- Read data from serial device and save the data in buffer.
-
- @param Buffer Point of data buffer which need to be written.
- @param NumberOfBytes Number of output bytes which are cached in Buffer.
-
- @retval 0 Read data failed.
- @retval !0 Actual number of bytes read from serial device.
-
-**/
-UINTN
-EFIAPI
-PL011UartRead (
- IN UINTN UartBase,
- OUT UINT8 *Buffer,
- IN UINTN NumberOfBytes
- );
-
-/**
- Check to see if any data is available to be read from the debug device.
-
- @retval TRUE At least one byte of data is available to be read
- @retval FALSE No data is available to be read
-
-**/
-BOOLEAN
-EFIAPI
-PL011UartPoll (
- IN UINTN UartBase
- );
-
-#endif
Remove the PL011UartLib implementation that has been superseded by the one under Library/ Contributed-under: TianoCore Contribution Agreement 1.1 Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> --- ArmPlatformPkg/Drivers/PL011Uart/PL011Uart.c | 470 -------------------- ArmPlatformPkg/Drivers/PL011Uart/PL011Uart.inf | 42 -- ArmPlatformPkg/Include/Drivers/PL011Uart.h | 290 ------------ 3 files changed, 802 deletions(-) -- 2.11.0 _______________________________________________ edk2-devel mailing list edk2-devel@lists.01.org https://lists.01.org/mailman/listinfo/edk2-devel