@@ -17,4 +17,4 @@ obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
obj-$(CONFIG_LOCAL_TIMERS) += localtimer.o
obj-$(CONFIG_U5500_MODEM_IRQ) += modem-irq-db5500.o
obj-$(CONFIG_U5500_MBOX) += mbox-db5500.o
-obj-$(CONFIG_CPU_FREQ) += cpufreq.o
+
@@ -131,9 +131,14 @@ static struct platform_device db8500_pmu_device = {
.dev.platform_data = &db8500_pmu_platdata,
};
+static struct platform_device db8500_prcmu_device = {
+ .name = "db8500-prcmu",
+};
+
static struct platform_device *platform_devs[] __initdata = {
&u8500_dma40_device,
&db8500_pmu_device,
+ &db8500_prcmu_device,
};
static resource_size_t __initdata db8500_gpio_base[] = {
@@ -9,86 +9,158 @@
*
* PRCM Unit registers
*/
+#ifndef __DB8500_PRCMU_REGS_H
+#define __DB8500_PRCMU_REGS_H
-#ifndef __MACH_PRCMU_REGS_H
-#define __MACH_PRCMU_REGS_H
-
+#include <linux/bitops.h>
#include <mach/hardware.h>
-#define PRCM_ARM_PLLDIVPS (_PRCMU_BASE + 0x118)
-#define PRCM_ARM_CHGCLKREQ (_PRCMU_BASE + 0x114)
-#define PRCM_PLLARM_ENABLE (_PRCMU_BASE + 0x98)
-#define PRCM_ARMCLKFIX_MGT (_PRCMU_BASE + 0x0)
-#define PRCM_A9_RESETN_CLR (_PRCMU_BASE + 0x1f4)
-#define PRCM_A9_RESETN_SET (_PRCMU_BASE + 0x1f0)
-#define PRCM_ARM_LS_CLAMP (_PRCMU_BASE + 0x30c)
-#define PRCM_SRAM_A9 (_PRCMU_BASE + 0x308)
+#define BITS(_start, _end) ((BIT(_end) - BIT(_start)) + BIT(_end))
+
+#define PRCM_ARM_PLLDIVPS 0x118
+#define PRCM_ARM_PLLDIVPS_ARM_BRM_RATE BITS(0, 5)
+#define PRCM_ARM_PLLDIVPS_MAX_MASK 0xF
+
+#define PRCM_PLLARM_LOCKP 0x0A8
+#define PRCM_PLLARM_LOCKP_PRCM_PLLARM_LOCKP3 BIT(1)
+
+#define PRCM_ARM_CHGCLKREQ 0x114
+#define PRCM_ARM_CHGCLKREQ_PRCM_ARM_CHGCLKREQ BIT(0)
+
+#define PRCM_PLLARM_ENABLE 0x98
+#define PRCM_PLLARM_ENABLE_PRCM_PLLARM_ENABLE BIT(0)
+#define PRCM_PLLARM_ENABLE_PRCM_PLLARM_COUNTON BIT(8)
+
+#define PRCM_ARMCLKFIX_MGT 0x0
+#define PRCM_A9_RESETN_CLR 0x1f4
+#define PRCM_A9_RESETN_SET 0x1f0
+#define PRCM_ARM_LS_CLAMP 0x30C
+#define PRCM_SRAM_A9 0x308
/* ARM WFI Standby signal register */
-#define PRCM_ARM_WFI_STANDBY (_PRCMU_BASE + 0x130)
-#define PRCMU_IOCR (_PRCMU_BASE + 0x310)
+#define PRCM_ARM_WFI_STANDBY 0x130
+#define PRCM_IOCR 0x310
+#define PRCM_IOCR_IOFORCE BIT(0)
/* CPU mailbox registers */
-#define PRCM_MBOX_CPU_VAL (_PRCMU_BASE + 0x0fc)
-#define PRCM_MBOX_CPU_SET (_PRCMU_BASE + 0x100)
-#define PRCM_MBOX_CPU_CLR (_PRCMU_BASE + 0x104)
+#define PRCM_MBOX_CPU_VAL 0x0FC
+#define PRCM_MBOX_CPU_SET 0x100
/* Dual A9 core interrupt management unit registers */
-#define PRCM_A9_MASK_REQ (_PRCMU_BASE + 0x328)
-#define PRCM_A9_MASK_ACK (_PRCMU_BASE + 0x32c)
-#define PRCM_ARMITMSK31TO0 (_PRCMU_BASE + 0x11c)
-#define PRCM_ARMITMSK63TO32 (_PRCMU_BASE + 0x120)
-#define PRCM_ARMITMSK95TO64 (_PRCMU_BASE + 0x124)
-#define PRCM_ARMITMSK127TO96 (_PRCMU_BASE + 0x128)
-#define PRCM_POWER_STATE_VAL (_PRCMU_BASE + 0x25C)
-#define PRCM_ARMITVAL31TO0 (_PRCMU_BASE + 0x260)
-#define PRCM_ARMITVAL63TO32 (_PRCMU_BASE + 0x264)
-#define PRCM_ARMITVAL95TO64 (_PRCMU_BASE + 0x268)
-#define PRCM_ARMITVAL127TO96 (_PRCMU_BASE + 0x26C)
-
-#define PRCM_HOSTACCESS_REQ (_PRCMU_BASE + 0x334)
-#define ARM_WAKEUP_MODEM 0x1
-
-#define PRCM_ARM_IT1_CLEAR (_PRCMU_BASE + 0x48C)
-#define PRCM_ARM_IT1_VAL (_PRCMU_BASE + 0x494)
-#define PRCM_HOLD_EVT (_PRCMU_BASE + 0x174)
-
-#define PRCM_ITSTATUS0 (_PRCMU_BASE + 0x148)
-#define PRCM_ITSTATUS1 (_PRCMU_BASE + 0x150)
-#define PRCM_ITSTATUS2 (_PRCMU_BASE + 0x158)
-#define PRCM_ITSTATUS3 (_PRCMU_BASE + 0x160)
-#define PRCM_ITSTATUS4 (_PRCMU_BASE + 0x168)
-#define PRCM_ITSTATUS5 (_PRCMU_BASE + 0x484)
-#define PRCM_ITCLEAR5 (_PRCMU_BASE + 0x488)
-#define PRCM_ARMIT_MASKXP70_IT (_PRCMU_BASE + 0x1018)
+#define PRCM_A9_MASK_REQ 0x328
+#define PRCM_A9_MASK_REQ_PRCM_A9_MASK_REQ BIT(0)
+
+#define PRCM_A9_MASK_ACK 0x32C
+#define PRCM_ARMITMSK31TO0 0x11C
+#define PRCM_ARMITMSK63TO32 0x120
+#define PRCM_ARMITMSK95TO64 0x124
+#define PRCM_ARMITMSK127TO96 0x128
+#define PRCM_POWER_STATE_VAL 0x25C
+#define PRCM_ARMITVAL31TO0 0x260
+#define PRCM_ARMITVAL63TO32 0x264
+#define PRCM_ARMITVAL95TO64 0x268
+#define PRCM_ARMITVAL127TO96 0x26C
+
+#define PRCM_HOSTACCESS_REQ 0x334
+#define PRCM_HOSTACCESS_REQ_HOSTACCESS_REQ BIT(0)
+
+#define PRCM_ARM_IT1_CLR 0x48C
+#define PRCM_ARM_IT1_VAL 0x494
+
+#define PRCM_ITSTATUS0 0x148
+#define PRCM_ITSTATUS1 0x150
+#define PRCM_ITSTATUS2 0x158
+#define PRCM_ITSTATUS3 0x160
+#define PRCM_ITSTATUS4 0x168
+#define PRCM_ITSTATUS5 0x484
+#define PRCM_ITCLEAR5 0x488
+#define PRCM_ARMIT_MASKXP70_IT 0x1018
/* System reset register */
-#define PRCM_APE_SOFTRST (_PRCMU_BASE + 0x228)
+#define PRCM_APE_SOFTRST 0x228
/* Level shifter and clamp control registers */
-#define PRCM_MMIP_LS_CLAMP_SET (_PRCMU_BASE + 0x420)
-#define PRCM_MMIP_LS_CLAMP_CLR (_PRCMU_BASE + 0x424)
+#define PRCM_MMIP_LS_CLAMP_SET 0x420
+#define PRCM_MMIP_LS_CLAMP_CLR 0x424
+
+/* PRCMU HW semaphore */
+#define PRCM_SEM 0x400
+#define PRCM_SEM_PRCM_SEM BIT(0)
/* PRCMU clock/PLL/reset registers */
-#define PRCM_PLLDSI_FREQ (_PRCMU_BASE + 0x500)
-#define PRCM_PLLDSI_ENABLE (_PRCMU_BASE + 0x504)
-#define PRCM_LCDCLK_MGT (_PRCMU_BASE + 0x044)
-#define PRCM_MCDECLK_MGT (_PRCMU_BASE + 0x064)
-#define PRCM_HDMICLK_MGT (_PRCMU_BASE + 0x058)
-#define PRCM_TVCLK_MGT (_PRCMU_BASE + 0x07c)
-#define PRCM_DSI_PLLOUT_SEL (_PRCMU_BASE + 0x530)
-#define PRCM_DSITVCLK_DIV (_PRCMU_BASE + 0x52C)
-#define PRCM_APE_RESETN_SET (_PRCMU_BASE + 0x1E4)
-#define PRCM_APE_RESETN_CLR (_PRCMU_BASE + 0x1E8)
+#define PRCM_PLLDSI_FREQ 0x500
+#define PRCM_PLLDSI_ENABLE 0x504
+#define PRCM_PLLDSI_LOCKP 0x508
+#define PRCM_DSI_PLLOUT_SEL 0x530
+#define PRCM_DSITVCLK_DIV 0x52C
+#define PRCM_APE_RESETN_SET 0x1E4
+#define PRCM_APE_RESETN_CLR 0x1E8
+
+#define PRCM_TCR 0x1C8
+#define PRCM_TCR_TENSEL_MASK BITS(0, 7)
+#define PRCM_TCR_STOP_TIMERS BIT(16)
+#define PRCM_TCR_DOZE_MODE BIT(17)
+
+#define PRCM_CLKOCR 0x1CC
+#define PRCM_CLKOCR_CLKODIV0_SHIFT 0
+#define PRCM_CLKOCR_CLKODIV0_MASK BITS(0, 5)
+#define PRCM_CLKOCR_CLKOSEL0_SHIFT 6
+#define PRCM_CLKOCR_CLKOSEL0_MASK BITS(6, 8)
+#define PRCM_CLKOCR_CLKODIV1_SHIFT 16
+#define PRCM_CLKOCR_CLKODIV1_MASK BITS(16, 21)
+#define PRCM_CLKOCR_CLKOSEL1_SHIFT 22
+#define PRCM_CLKOCR_CLKOSEL1_MASK BITS(22, 24)
+#define PRCM_CLKOCR_CLK1TYPE BIT(28)
+
+#define PRCM_SGACLK_MGT 0x014
+#define PRCM_UARTCLK_MGT 0x018
+#define PRCM_MSP02CLK_MGT 0x01C
+#define PRCM_MSP1CLK_MGT 0x288
+#define PRCM_I2CCLK_MGT 0x020
+#define PRCM_SDMMCCLK_MGT 0x024
+#define PRCM_SLIMCLK_MGT 0x028
+#define PRCM_PER1CLK_MGT 0x02C
+#define PRCM_PER2CLK_MGT 0x030
+#define PRCM_PER3CLK_MGT 0x034
+#define PRCM_PER5CLK_MGT 0x038
+#define PRCM_PER6CLK_MGT 0x03C
+#define PRCM_PER7CLK_MGT 0x040
+#define PRCM_LCDCLK_MGT 0x044
+#define PRCM_BMLCLK_MGT 0x04C
+#define PRCM_HSITXCLK_MGT 0x050
+#define PRCM_HSIRXCLK_MGT 0x054
+#define PRCM_HDMICLK_MGT 0x058
+#define PRCM_APEATCLK_MGT 0x05C
+#define PRCM_APETRACECLK_MGT 0x060
+#define PRCM_MCDECLK_MGT 0x064
+#define PRCM_IPI2CCLK_MGT 0x068
+#define PRCM_DSIALTCLK_MGT 0x06C
+#define PRCM_DMACLK_MGT 0x074
+#define PRCM_B2R2CLK_MGT 0x078
+#define PRCM_TVCLK_MGT 0x07C
+#define PRCM_UNIPROCLK_MGT 0x278
+#define PRCM_SSPCLK_MGT 0x280
+#define PRCM_RNGCLK_MGT 0x284
+#define PRCM_UICCCLK_MGT 0x27C
+
+#define PRCM_CLK_MGT_CLKPLLDIV_MASK BITS(0, 4)
+#define PRCM_CLK_MGT_CLKPLLSW_MASK BITS(5, 7)
+#define PRCM_CLK_MGT_CLKEN BIT(8)
/* ePOD and memory power signal control registers */
-#define PRCM_EPOD_C_SET (_PRCMU_BASE + 0x410)
-#define PRCM_SRAM_LS_SLEEP (_PRCMU_BASE + 0x304)
+#define PRCM_EPOD_C_SET 0x410
+#define PRCM_SRAM_LS_SLEEP 0x304
/* Debug power control unit registers */
-#define PRCM_POWER_STATE_SET (_PRCMU_BASE + 0x254)
+#define PRCM_POWER_STATE_SET 0x254
/* Miscellaneous unit registers */
-#define PRCM_DSI_SW_RESET (_PRCMU_BASE + 0x324)
+#define PRCM_DSI_SW_RESET 0x324
+#define PRCM_GPIOCR 0x138
+
+/* GPIOCR register */
+#define PRCM_GPIOCR_SPI2_SELECT BIT(23)
+
+#define PRCM_DDR_SUBSYS_APE_MINBW 0x438
-#endif /* __MACH_PRCMU_REGS_H */
+#endif /* __DB8500_PRCMU_REGS_H */
@@ -10,93 +10,1354 @@
* U8500 PRCM Unit interface driver
*
*/
-#include <linux/kernel.h>
#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/err.h>
+#include <linux/spinlock.h>
#include <linux/io.h>
+#include <linux/slab.h>
#include <linux/mutex.h>
#include <linux/completion.h>
+#include <linux/irq.h>
#include <linux/jiffies.h>
#include <linux/bitops.h>
-#include <linux/interrupt.h>
+#include <linux/fs.h>
+#include <linux/platform_device.h>
+#include <linux/uaccess.h>
+#include <linux/mfd/core.h>
#include <linux/mfd/db8500-prcmu.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+#include <mach/db8500-regs.h>
+#include <mach/id.h>
+#include "db8500-prcmu-regs.h"
+
+/* Offset for the firmware version within the TCPM */
+#define PRCMU_FW_VERSION_OFFSET 0xA4
+
+/* PRCMU project numbers, defined by PRCMU FW */
+#define PRCMU_PROJECT_ID_8500V1_0 1
+#define PRCMU_PROJECT_ID_8500V2_0 2
+#define PRCMU_PROJECT_ID_8400V2_0 3
+
+/* Index of different voltages to be used when accessing AVSData */
+#define PRCM_AVS_BASE 0x2FC
+#define PRCM_AVS_VBB_RET (PRCM_AVS_BASE + 0x0)
+#define PRCM_AVS_VBB_MAX_OPP (PRCM_AVS_BASE + 0x1)
+#define PRCM_AVS_VBB_100_OPP (PRCM_AVS_BASE + 0x2)
+#define PRCM_AVS_VBB_50_OPP (PRCM_AVS_BASE + 0x3)
+#define PRCM_AVS_VARM_MAX_OPP (PRCM_AVS_BASE + 0x4)
+#define PRCM_AVS_VARM_100_OPP (PRCM_AVS_BASE + 0x5)
+#define PRCM_AVS_VARM_50_OPP (PRCM_AVS_BASE + 0x6)
+#define PRCM_AVS_VARM_RET (PRCM_AVS_BASE + 0x7)
+#define PRCM_AVS_VAPE_100_OPP (PRCM_AVS_BASE + 0x8)
+#define PRCM_AVS_VAPE_50_OPP (PRCM_AVS_BASE + 0x9)
+#define PRCM_AVS_VMOD_100_OPP (PRCM_AVS_BASE + 0xA)
+#define PRCM_AVS_VMOD_50_OPP (PRCM_AVS_BASE + 0xB)
+#define PRCM_AVS_VSAFE (PRCM_AVS_BASE + 0xC)
+
+#define PRCM_AVS_VOLTAGE 0
+#define PRCM_AVS_VOLTAGE_MASK 0x3f
+#define PRCM_AVS_ISSLOWSTARTUP 6
+#define PRCM_AVS_ISSLOWSTARTUP_MASK (1 << PRCM_AVS_ISSLOWSTARTUP)
+#define PRCM_AVS_ISMODEENABLE 7
+#define PRCM_AVS_ISMODEENABLE_MASK (1 << PRCM_AVS_ISMODEENABLE)
+
+#define PRCM_BOOT_STATUS 0xFFF
+#define PRCM_ROMCODE_A2P 0xFFE
+#define PRCM_ROMCODE_P2A 0xFFD
+#define PRCM_XP70_CUR_PWR_STATE 0xFFC /* 4 BYTES */
+
+#define PRCM_SW_RST_REASON 0xFF8 /* 2 bytes */
+
+#define _PRCM_MBOX_HEADER 0xFE8 /* 16 bytes */
+#define PRCM_MBOX_HEADER_REQ_MB0 (_PRCM_MBOX_HEADER + 0x0)
+#define PRCM_MBOX_HEADER_REQ_MB1 (_PRCM_MBOX_HEADER + 0x1)
+#define PRCM_MBOX_HEADER_REQ_MB2 (_PRCM_MBOX_HEADER + 0x2)
+#define PRCM_MBOX_HEADER_REQ_MB3 (_PRCM_MBOX_HEADER + 0x3)
+#define PRCM_MBOX_HEADER_REQ_MB4 (_PRCM_MBOX_HEADER + 0x4)
+#define PRCM_MBOX_HEADER_REQ_MB5 (_PRCM_MBOX_HEADER + 0x5)
+#define PRCM_MBOX_HEADER_ACK_MB0 (_PRCM_MBOX_HEADER + 0x8)
+
+/* Req Mailboxes */
+#define PRCM_REQ_MB0 0xFDC /* 12 bytes */
+#define PRCM_REQ_MB1 0xFD0 /* 12 bytes */
+#define PRCM_REQ_MB2 0xFC0 /* 16 bytes */
+#define PRCM_REQ_MB3 0xE4C /* 372 bytes */
+#define PRCM_REQ_MB4 0xE48 /* 4 bytes */
+#define PRCM_REQ_MB5 0xE44 /* 4 bytes */
+
+/* Ack Mailboxes */
+#define PRCM_ACK_MB0 0xE08 /* 52 bytes */
+#define PRCM_ACK_MB1 0xE04 /* 4 bytes */
+#define PRCM_ACK_MB2 0xE00 /* 4 bytes */
+#define PRCM_ACK_MB3 0xDFC /* 4 bytes */
+#define PRCM_ACK_MB4 0xDF8 /* 4 bytes */
+#define PRCM_ACK_MB5 0xDF4 /* 4 bytes */
+
+/* Mailbox 0 headers */
+#define MB0H_POWER_STATE_TRANS 0
+#define MB0H_CONFIG_WAKEUPS_EXE 1
+#define MB0H_READ_WAKEUP_ACK 3
+#define MB0H_CONFIG_WAKEUPS_SLEEP 4
+
+#define MB0H_WAKEUP_EXE 2
+#define MB0H_WAKEUP_SLEEP 5
+
+/* Mailbox 0 REQs */
+#define PRCM_REQ_MB0_AP_POWER_STATE (PRCM_REQ_MB0 + 0x0)
+#define PRCM_REQ_MB0_AP_PLL_STATE (PRCM_REQ_MB0 + 0x1)
+#define PRCM_REQ_MB0_ULP_CLOCK_STATE (PRCM_REQ_MB0 + 0x2)
+#define PRCM_REQ_MB0_DO_NOT_WFI (PRCM_REQ_MB0 + 0x3)
+#define PRCM_REQ_MB0_WAKEUP_8500 (PRCM_REQ_MB0 + 0x4)
+#define PRCM_REQ_MB0_WAKEUP_4500 (PRCM_REQ_MB0 + 0x8)
+
+/* Mailbox 0 ACKs */
+#define PRCM_ACK_MB0_AP_PWRSTTR_STATUS (PRCM_ACK_MB0 + 0x0)
+#define PRCM_ACK_MB0_READ_POINTER (PRCM_ACK_MB0 + 0x1)
+#define PRCM_ACK_MB0_WAKEUP_0_8500 (PRCM_ACK_MB0 + 0x4)
+#define PRCM_ACK_MB0_WAKEUP_0_4500 (PRCM_ACK_MB0 + 0x8)
+#define PRCM_ACK_MB0_WAKEUP_1_8500 (PRCM_ACK_MB0 + 0x1C)
+#define PRCM_ACK_MB0_WAKEUP_1_4500 (PRCM_ACK_MB0 + 0x20)
+#define PRCM_ACK_MB0_EVENT_4500_NUMBERS 20
+
+/* Mailbox 1 headers */
+#define MB1H_ARM_APE_OPP 0x0
+#define MB1H_RESET_MODEM 0x2
+#define MB1H_REQUEST_APE_OPP_100_VOLT 0x3
+#define MB1H_RELEASE_APE_OPP_100_VOLT 0x4
+#define MB1H_RELEASE_USB_WAKEUP 0x5
+
+/* Mailbox 1 Requests */
+#define PRCM_REQ_MB1_ARM_OPP (PRCM_REQ_MB1 + 0x0)
+#define PRCM_REQ_MB1_APE_OPP (PRCM_REQ_MB1 + 0x1)
+#define PRCM_REQ_MB1_APE_OPP_100_RESTORE (PRCM_REQ_MB1 + 0x4)
+#define PRCM_REQ_MB1_ARM_OPP_100_RESTORE (PRCM_REQ_MB1 + 0x8)
+
+/* Mailbox 1 ACKs */
+#define PRCM_ACK_MB1_CURRENT_ARM_OPP (PRCM_ACK_MB1 + 0x0)
+#define PRCM_ACK_MB1_CURRENT_APE_OPP (PRCM_ACK_MB1 + 0x1)
+#define PRCM_ACK_MB1_APE_VOLTAGE_STATUS (PRCM_ACK_MB1 + 0x2)
+#define PRCM_ACK_MB1_DVFS_STATUS (PRCM_ACK_MB1 + 0x3)
+
+/* Mailbox 2 headers */
+#define MB2H_DPS 0x0
+#define MB2H_AUTO_PWR 0x1
+
+/* Mailbox 2 REQs */
+#define PRCM_REQ_MB2_SVA_MMDSP (PRCM_REQ_MB2 + 0x0)
+#define PRCM_REQ_MB2_SVA_PIPE (PRCM_REQ_MB2 + 0x1)
+#define PRCM_REQ_MB2_SIA_MMDSP (PRCM_REQ_MB2 + 0x2)
+#define PRCM_REQ_MB2_SIA_PIPE (PRCM_REQ_MB2 + 0x3)
+#define PRCM_REQ_MB2_SGA (PRCM_REQ_MB2 + 0x4)
+#define PRCM_REQ_MB2_B2R2_MCDE (PRCM_REQ_MB2 + 0x5)
+#define PRCM_REQ_MB2_ESRAM12 (PRCM_REQ_MB2 + 0x6)
+#define PRCM_REQ_MB2_ESRAM34 (PRCM_REQ_MB2 + 0x7)
+#define PRCM_REQ_MB2_AUTO_PM_SLEEP (PRCM_REQ_MB2 + 0x8)
+#define PRCM_REQ_MB2_AUTO_PM_IDLE (PRCM_REQ_MB2 + 0xC)
+
+/* Mailbox 2 ACKs */
+#define PRCM_ACK_MB2_DPS_STATUS (PRCM_ACK_MB2 + 0x0)
+#define HWACC_PWR_ST_OK 0xFE
+
+/* Mailbox 3 headers */
+#define MB3H_ANC 0x0
+#define MB3H_SIDETONE 0x1
+#define MB3H_SYSCLK 0xE
+
+/* Mailbox 3 Requests */
+#define PRCM_REQ_MB3_ANC_FIR_COEFF (PRCM_REQ_MB3 + 0x0)
+#define PRCM_REQ_MB3_ANC_IIR_COEFF (PRCM_REQ_MB3 + 0x20)
+#define PRCM_REQ_MB3_ANC_SHIFTER (PRCM_REQ_MB3 + 0x60)
+#define PRCM_REQ_MB3_ANC_WARP (PRCM_REQ_MB3 + 0x64)
+#define PRCM_REQ_MB3_SIDETONE_FIR_GAIN (PRCM_REQ_MB3 + 0x68)
+#define PRCM_REQ_MB3_SIDETONE_FIR_COEFF (PRCM_REQ_MB3 + 0x6C)
+#define PRCM_REQ_MB3_SYSCLK_MGT (PRCM_REQ_MB3 + 0x16C)
+
+/* Mailbox 4 headers */
+#define MB4H_DDR_INIT 0x0
+#define MB4H_MEM_ST 0x1
+#define MB4H_HOTDOG 0x12
+#define MB4H_HOTMON 0x13
+#define MB4H_HOT_PERIOD 0x14
+
+/* Mailbox 4 Requests */
+#define PRCM_REQ_MB4_DDR_ST_AP_SLEEP_IDLE (PRCM_REQ_MB4 + 0x0)
+#define PRCM_REQ_MB4_DDR_ST_AP_DEEP_IDLE (PRCM_REQ_MB4 + 0x1)
+#define PRCM_REQ_MB4_ESRAM0_ST (PRCM_REQ_MB4 + 0x3)
+#define PRCM_REQ_MB4_HOTDOG_THRESHOLD (PRCM_REQ_MB4 + 0x0)
+#define PRCM_REQ_MB4_HOTMON_LOW (PRCM_REQ_MB4 + 0x0)
+#define PRCM_REQ_MB4_HOTMON_HIGH (PRCM_REQ_MB4 + 0x1)
+#define PRCM_REQ_MB4_HOTMON_CONFIG (PRCM_REQ_MB4 + 0x2)
+#define PRCM_REQ_MB4_HOT_PERIOD (PRCM_REQ_MB4 + 0x0)
+#define HOTMON_CONFIG_LOW BIT(0)
+#define HOTMON_CONFIG_HIGH BIT(1)
+
+/* Mailbox 5 Requests */
+#define PRCM_REQ_MB5_I2C_SLAVE_OP (PRCM_REQ_MB5 + 0x0)
+#define PRCM_REQ_MB5_I2C_HW_BITS (PRCM_REQ_MB5 + 0x1)
+#define PRCM_REQ_MB5_I2C_REG (PRCM_REQ_MB5 + 0x2)
+#define PRCM_REQ_MB5_I2C_VAL (PRCM_REQ_MB5 + 0x3)
+#define PRCMU_I2C_WRITE(slave) \
+ (((slave) << 1) | (cpu_is_u8500v2() ? BIT(6) : 0))
+#define PRCMU_I2C_READ(slave) \
+ (((slave) << 1) | BIT(0) | (cpu_is_u8500v2() ? BIT(6) : 0))
+#define PRCMU_I2C_STOP_EN BIT(3)
+
+/* Mailbox 5 ACKs */
+#define PRCM_ACK_MB5_I2C_STATUS (PRCM_ACK_MB5 + 0x1)
+#define PRCM_ACK_MB5_I2C_VAL (PRCM_ACK_MB5 + 0x3)
+#define I2C_WR_OK 0x1
+#define I2C_RD_OK 0x2
+
+#define NUM_MB 8
+#define MBOX_BIT BIT
+#define ALL_MBOX_BITS (MBOX_BIT(NUM_MB) - 1)
+
+/*
+ * Wakeups/IRQs
+ */
+
+#define WAKEUP_BIT_RTC BIT(0)
+#define WAKEUP_BIT_RTT0 BIT(1)
+#define WAKEUP_BIT_RTT1 BIT(2)
+#define WAKEUP_BIT_HSI0 BIT(3)
+#define WAKEUP_BIT_HSI1 BIT(4)
+#define WAKEUP_BIT_CA_WAKE BIT(5)
+#define WAKEUP_BIT_USB BIT(6)
+#define WAKEUP_BIT_ABB BIT(7)
+#define WAKEUP_BIT_ABB_FIFO BIT(8)
+#define WAKEUP_BIT_SYSCLK_OK BIT(9)
+#define WAKEUP_BIT_CA_SLEEP BIT(10)
+#define WAKEUP_BIT_AC_WAKE_ACK BIT(11)
+#define WAKEUP_BIT_SIDE_TONE_OK BIT(12)
+#define WAKEUP_BIT_ANC_OK BIT(13)
+#define WAKEUP_BIT_SW_ERROR BIT(14)
+#define WAKEUP_BIT_AC_SLEEP_ACK BIT(15)
+#define WAKEUP_BIT_ARM BIT(17)
+#define WAKEUP_BIT_HOTMON_LOW BIT(18)
+#define WAKEUP_BIT_HOTMON_HIGH BIT(19)
+#define WAKEUP_BIT_MODEM_SW_RESET_REQ BIT(20)
+#define WAKEUP_BIT_GPIO0 BIT(23)
+#define WAKEUP_BIT_GPIO1 BIT(24)
+#define WAKEUP_BIT_GPIO2 BIT(25)
+#define WAKEUP_BIT_GPIO3 BIT(26)
+#define WAKEUP_BIT_GPIO4 BIT(27)
+#define WAKEUP_BIT_GPIO5 BIT(28)
+#define WAKEUP_BIT_GPIO6 BIT(29)
+#define WAKEUP_BIT_GPIO7 BIT(30)
+#define WAKEUP_BIT_GPIO8 BIT(31)
+
+/*
+ * This vector maps irq numbers to the bits in the bit field used in
+ * communication with the PRCMU firmware.
+ *
+ * The reason for having this is to keep the irq numbers contiguous even though
+ * the bits in the bit field are not. (The bits also have a tendency to move
+ * around, to further complicate matters.)
+ */
+#define IRQ_INDEX(_name) ((IRQ_PRCMU_##_name) - IRQ_PRCMU_BASE)
+#define IRQ_ENTRY(_name)[IRQ_INDEX(_name)] = (WAKEUP_BIT_##_name)
+static u32 prcmu_irq_bit[NUM_PRCMU_WAKEUPS] = {
+ IRQ_ENTRY(RTC),
+ IRQ_ENTRY(RTT0),
+ IRQ_ENTRY(RTT1),
+ IRQ_ENTRY(HSI0),
+ IRQ_ENTRY(HSI1),
+ IRQ_ENTRY(CA_WAKE),
+ IRQ_ENTRY(USB),
+ IRQ_ENTRY(ABB),
+ IRQ_ENTRY(ABB_FIFO),
+ IRQ_ENTRY(CA_SLEEP),
+ IRQ_ENTRY(ARM),
+ IRQ_ENTRY(HOTMON_LOW),
+ IRQ_ENTRY(HOTMON_HIGH),
+ IRQ_ENTRY(MODEM_SW_RESET_REQ),
+ IRQ_ENTRY(GPIO0),
+ IRQ_ENTRY(GPIO1),
+ IRQ_ENTRY(GPIO2),
+ IRQ_ENTRY(GPIO3),
+ IRQ_ENTRY(GPIO4),
+ IRQ_ENTRY(GPIO5),
+ IRQ_ENTRY(GPIO6),
+ IRQ_ENTRY(GPIO7),
+ IRQ_ENTRY(GPIO8)
+};
+
+#define VALID_WAKEUPS (BIT(NUM_PRCMU_WAKEUP_INDICES) - 1)
+#define WAKEUP_ENTRY(_name)[PRCMU_WAKEUP_INDEX_##_name] = (WAKEUP_BIT_##_name)
+static u32 prcmu_wakeup_bit[NUM_PRCMU_WAKEUP_INDICES] = {
+ WAKEUP_ENTRY(RTC),
+ WAKEUP_ENTRY(RTT0),
+ WAKEUP_ENTRY(RTT1),
+ WAKEUP_ENTRY(HSI0),
+ WAKEUP_ENTRY(HSI1),
+ WAKEUP_ENTRY(USB),
+ WAKEUP_ENTRY(ABB),
+ WAKEUP_ENTRY(ABB_FIFO),
+ WAKEUP_ENTRY(ARM)
+};
+
+/*
+ * mb0_transfer - state needed for mailbox 0 communication.
+ * @lock: The transaction lock.
+ * @dbb_events_lock: A lock used to handle concurrent access to (parts of)
+ * the request data.
+ * @mask_work: Work structure used for (un)masking wakeup interrupts.
+ * @req: Request data that need to persist between requests.
+ */
+static struct {
+ spinlock_t lock;
+ spinlock_t dbb_irqs_lock;
+ struct work_struct mask_work;
+ struct mutex ac_wake_lock;
+ struct completion ac_wake_work;
+ struct {
+ u32 dbb_irqs;
+ u32 dbb_wakeups;
+ u32 abb_events;
+ } req;
+} mb0_transfer;
+
+/*
+ * mb1_transfer - state needed for mailbox 1 communication.
+ * @lock: The transaction lock.
+ * @work: The transaction completion structure.
+ * @ack: Reply ("acknowledge") data.
+ */
+static struct {
+ struct mutex lock;
+ struct completion work;
+ struct {
+ u8 header;
+ u8 arm_opp;
+ u8 ape_opp;
+ u8 ape_voltage_status;
+ } ack;
+} mb1_transfer;
+
+/*
+ * mb2_transfer - state needed for mailbox 2 communication.
+ * @lock: The transaction lock.
+ * @work: The transaction completion structure.
+ * @auto_pm_lock: The autonomous power management configuration lock.
+ * @auto_pm_enabled: A flag indicating whether autonomous PM is enabled.
+ * @req: Request data that need to persist between requests.
+ * @ack: Reply ("acknowledge") data.
+ */
+static struct {
+ struct mutex lock;
+ struct completion work;
+ spinlock_t auto_pm_lock;
+ bool auto_pm_enabled;
+ struct {
+ u8 status;
+ } ack;
+} mb2_transfer;
+
+/*
+ * mb3_transfer - state needed for mailbox 3 communication.
+ * @lock: The request lock.
+ * @sysclk_lock: A lock used to handle concurrent sysclk requests.
+ * @sysclk_work: Work structure used for sysclk requests.
+ */
+static struct {
+ spinlock_t lock;
+ struct mutex sysclk_lock;
+ struct completion sysclk_work;
+} mb3_transfer;
+
+/*
+ * mb4_transfer - state needed for mailbox 4 communication.
+ * @lock: The transaction lock.
+ * @work: The transaction completion structure.
+ */
+static struct {
+ struct mutex lock;
+ struct completion work;
+} mb4_transfer;
+
+/*
+ * mb5_transfer - state needed for mailbox 5 communication.
+ * @lock: The transaction lock.
+ * @work: The transaction completion structure.
+ * @ack: Reply ("acknowledge") data.
+ */
+static struct {
+ struct mutex lock;
+ struct completion work;
+ struct {
+ u8 status;
+ u8 value;
+ } ack;
+} mb5_transfer;
+
+static atomic_t ac_wake_req_state = ATOMIC_INIT(0);
+
+/* Spinlocks */
+static DEFINE_SPINLOCK(clkout_lock);
+static DEFINE_SPINLOCK(gpiocr_lock);
+
+/* Global var to runtime determine TCDM base for v2 or v1 */
+static __iomem void *tcdm_base;
+
+struct clk_mgt {
+ unsigned int offset;
+ u32 pllsw;
+};
+
+static DEFINE_SPINLOCK(clk_mgt_lock);
+
+#define CLK_MGT_ENTRY(_name)[PRCMU_##_name] = { (PRCM_##_name##_MGT), 0 }
+struct clk_mgt clk_mgt[PRCMU_NUM_REG_CLOCKS] = {
+ CLK_MGT_ENTRY(SGACLK),
+ CLK_MGT_ENTRY(UARTCLK),
+ CLK_MGT_ENTRY(MSP02CLK),
+ CLK_MGT_ENTRY(MSP1CLK),
+ CLK_MGT_ENTRY(I2CCLK),
+ CLK_MGT_ENTRY(SDMMCCLK),
+ CLK_MGT_ENTRY(SLIMCLK),
+ CLK_MGT_ENTRY(PER1CLK),
+ CLK_MGT_ENTRY(PER2CLK),
+ CLK_MGT_ENTRY(PER3CLK),
+ CLK_MGT_ENTRY(PER5CLK),
+ CLK_MGT_ENTRY(PER6CLK),
+ CLK_MGT_ENTRY(PER7CLK),
+ CLK_MGT_ENTRY(LCDCLK),
+ CLK_MGT_ENTRY(BMLCLK),
+ CLK_MGT_ENTRY(HSITXCLK),
+ CLK_MGT_ENTRY(HSIRXCLK),
+ CLK_MGT_ENTRY(HDMICLK),
+ CLK_MGT_ENTRY(APEATCLK),
+ CLK_MGT_ENTRY(APETRACECLK),
+ CLK_MGT_ENTRY(MCDECLK),
+ CLK_MGT_ENTRY(IPI2CCLK),
+ CLK_MGT_ENTRY(DSIALTCLK),
+ CLK_MGT_ENTRY(DMACLK),
+ CLK_MGT_ENTRY(B2R2CLK),
+ CLK_MGT_ENTRY(TVCLK),
+ CLK_MGT_ENTRY(SSPCLK),
+ CLK_MGT_ENTRY(RNGCLK),
+ CLK_MGT_ENTRY(UICCCLK),
+};
+
+/*
+* Used by MCDE to setup all necessary PRCMU registers
+*/
+#define PRCMU_RESET_DSIPLL 0x00004000
+#define PRCMU_UNCLAMP_DSIPLL 0x00400800
+
+#define PRCMU_CLK_PLL_DIV_SHIFT 0
+#define PRCMU_CLK_PLL_SW_SHIFT 5
+#define PRCMU_CLK_38 (1 << 9)
+#define PRCMU_CLK_38_SRC (1 << 10)
+#define PRCMU_CLK_38_DIV (1 << 11)
+
+/* PLLDIV=12, PLLSW=4 (PLLDDR) */
+#define PRCMU_DSI_CLOCK_SETTING 0x0000008C
+
+/* PLLDIV=8, PLLSW=4 (PLLDDR) */
+#define PRCMU_DSI_CLOCK_SETTING_U8400 0x00000088
+
+/* DPI 50000000 Hz */
+#define PRCMU_DPI_CLOCK_SETTING ((1 << PRCMU_CLK_PLL_SW_SHIFT) | \
+ (16 << PRCMU_CLK_PLL_DIV_SHIFT))
+#define PRCMU_DSI_LP_CLOCK_SETTING 0x00000E00
+
+/* D=101, N=1, R=4, SELDIV2=0 */
+#define PRCMU_PLLDSI_FREQ_SETTING 0x00040165
+
+/* D=70, N=1, R=3, SELDIV2=0 */
+#define PRCMU_PLLDSI_FREQ_SETTING_U8400 0x00030146
+
+#define PRCMU_ENABLE_PLLDSI 0x00000001
+#define PRCMU_DISABLE_PLLDSI 0x00000000
+#define PRCMU_RELEASE_RESET_DSS 0x0000400C
+#define PRCMU_DSI_PLLOUT_SEL_SETTING 0x00000202
+/* ESC clk, div0=1, div1=1, div2=3 */
+#define PRCMU_ENABLE_ESCAPE_CLOCK_DIV 0x07030101
+#define PRCMU_DISABLE_ESCAPE_CLOCK_DIV 0x00030101
+#define PRCMU_DSI_RESET_SW 0x00000007
+
+#define PRCMU_PLLDSI_LOCKP_LOCKED 0x3
+
+static struct {
+ u8 project_number;
+ u8 api_version;
+ u8 func_version;
+ u8 errata;
+} prcmu_version;
+
+
+int prcmu_enable_dsipll(void)
+{
+ int i;
+ unsigned int plldsifreq;
+
+ /* Clear DSIPLL_RESETN */
+ writel(PRCMU_RESET_DSIPLL, (_PRCMU_BASE + PRCM_APE_RESETN_CLR));
+ /* Unclamp DSIPLL in/out */
+ writel(PRCMU_UNCLAMP_DSIPLL, (_PRCMU_BASE + PRCM_MMIP_LS_CLAMP_CLR));
+
+ if (prcmu_is_u8400())
+ plldsifreq = PRCMU_PLLDSI_FREQ_SETTING_U8400;
+ else
+ plldsifreq = PRCMU_PLLDSI_FREQ_SETTING;
+ /* Set DSI PLL FREQ */
+ writel(plldsifreq, (_PRCMU_BASE + PRCM_PLLDSI_FREQ));
+ writel(PRCMU_DSI_PLLOUT_SEL_SETTING,
+ (_PRCMU_BASE + PRCM_DSI_PLLOUT_SEL));
+ /* Enable Escape clocks */
+ writel(PRCMU_ENABLE_ESCAPE_CLOCK_DIV,
+ (_PRCMU_BASE + PRCM_DSITVCLK_DIV));
+
+ /* Start DSI PLL */
+ writel(PRCMU_ENABLE_PLLDSI, (_PRCMU_BASE + PRCM_PLLDSI_ENABLE));
+ /* Reset DSI PLL */
+ writel(PRCMU_DSI_RESET_SW, (_PRCMU_BASE + PRCM_DSI_SW_RESET));
+ for (i = 0; i < 10; i++) {
+ if ((readl(_PRCMU_BASE + PRCM_PLLDSI_LOCKP) &
+ PRCMU_PLLDSI_LOCKP_LOCKED)
+ == PRCMU_PLLDSI_LOCKP_LOCKED)
+ break;
+ udelay(100);
+ }
+ /* Set DSIPLL_RESETN */
+ writel(PRCMU_RESET_DSIPLL, (_PRCMU_BASE + PRCM_APE_RESETN_SET));
+ return 0;
+}
+
+int prcmu_disable_dsipll(void)
+{
+ /* Disable dsi pll */
+ writel(PRCMU_DISABLE_PLLDSI, (_PRCMU_BASE + PRCM_PLLDSI_ENABLE));
+ /* Disable escapeclock */
+ writel(PRCMU_DISABLE_ESCAPE_CLOCK_DIV,
+ (_PRCMU_BASE + PRCM_DSITVCLK_DIV));
+ return 0;
+}
+
+int prcmu_set_display_clocks(void)
+{
+ unsigned long flags;
+ unsigned int dsiclk;
+
+ if (prcmu_is_u8400())
+ dsiclk = PRCMU_DSI_CLOCK_SETTING_U8400;
+ else
+ dsiclk = PRCMU_DSI_CLOCK_SETTING;
+
+ spin_lock_irqsave(&clk_mgt_lock, flags);
+
+ /* Grab the HW semaphore. */
+ while ((readl(_PRCMU_BASE + PRCM_SEM) & PRCM_SEM_PRCM_SEM) != 0)
+ cpu_relax();
+
+ writel(dsiclk, (_PRCMU_BASE + PRCM_HDMICLK_MGT));
+ writel(PRCMU_DSI_LP_CLOCK_SETTING, (_PRCMU_BASE + PRCM_TVCLK_MGT));
+ writel(PRCMU_DPI_CLOCK_SETTING, (_PRCMU_BASE + PRCM_LCDCLK_MGT));
+
+ /* Release the HW semaphore. */
+ writel(0, (_PRCMU_BASE + PRCM_SEM));
+
+ spin_unlock_irqrestore(&clk_mgt_lock, flags);
+
+ return 0;
+}
+
+/**
+ * prcmu_enable_spi2 - Enables pin muxing for SPI2 on OtherAlternateC1.
+ */
+void prcmu_enable_spi2(void)
+{
+ u32 reg;
+ unsigned long flags;
+
+ spin_lock_irqsave(&gpiocr_lock, flags);
+ reg = readl(_PRCMU_BASE + PRCM_GPIOCR);
+ writel(reg | PRCM_GPIOCR_SPI2_SELECT, _PRCMU_BASE + PRCM_GPIOCR);
+ spin_unlock_irqrestore(&gpiocr_lock, flags);
+}
+
+/**
+ * prcmu_disable_spi2 - Disables pin muxing for SPI2 on OtherAlternateC1.
+ */
+void prcmu_disable_spi2(void)
+{
+ u32 reg;
+ unsigned long flags;
+
+ spin_lock_irqsave(&gpiocr_lock, flags);
+ reg = readl(_PRCMU_BASE + PRCM_GPIOCR);
+ writel(reg & ~PRCM_GPIOCR_SPI2_SELECT, _PRCMU_BASE + PRCM_GPIOCR);
+ spin_unlock_irqrestore(&gpiocr_lock, flags);
+}
+
+bool prcmu_has_arm_maxopp(void)
+{
+ return (readb(tcdm_base + PRCM_AVS_VARM_MAX_OPP) &
+ PRCM_AVS_ISMODEENABLE_MASK) == PRCM_AVS_ISMODEENABLE_MASK;
+}
+
+bool prcmu_is_u8400(void)
+{
+ return prcmu_version.project_number == PRCMU_PROJECT_ID_8400V2_0;
+}
+
+/**
+ * prcmu_get_boot_status - PRCMU boot status checking
+ * Returns: the current PRCMU boot status
+ */
+int prcmu_get_boot_status(void)
+{
+ return readb(tcdm_base + PRCM_BOOT_STATUS);
+}
+
+/**
+ * prcmu_set_rc_a2p - This function is used to run few power state sequences
+ * @val: Value to be set, i.e. transition requested
+ * Returns: 0 on success, -EINVAL on invalid argument
+ *
+ * This function is used to run the following power state sequences -
+ * any state to ApReset, ApDeepSleep to ApExecute, ApExecute to ApDeepSleep
+ */
+int prcmu_set_rc_a2p(enum romcode_write val)
+{
+ if (val < RDY_2_DS || val > RDY_2_XP70_RST)
+ return -EINVAL;
+ writeb(val, (tcdm_base + PRCM_ROMCODE_A2P));
+ return 0;
+}
+
+/**
+ * prcmu_get_rc_p2a - This function is used to get power state sequences
+ * Returns: the power transition that has last happened
+ *
+ * This function can return the following transitions-
+ * any state to ApReset, ApDeepSleep to ApExecute, ApExecute to ApDeepSleep
+ */
+enum romcode_read prcmu_get_rc_p2a(void)
+{
+ return readb(tcdm_base + PRCM_ROMCODE_P2A);
+}
+
+/**
+ * prcmu_get_current_mode - Return the current XP70 power mode
+ * Returns: Returns the current AP(ARM) power mode: init,
+ * apBoot, apExecute, apDeepSleep, apSleep, apIdle, apReset
+ */
+enum ap_pwrst prcmu_get_xp70_current_state(void)
+{
+ return readb(tcdm_base + PRCM_XP70_CUR_PWR_STATE);
+}
+
+/**
+ * prcmu_config_clkout - Configure one of the programmable clock outputs.
+ * @clkout: The CLKOUT number (0 or 1).
+ * @source: The clock to be used (one of the PRCMU_CLKSRC_*).
+ * @div: The divider to be applied.
+ *
+ * Configures one of the programmable clock outputs (CLKOUTs).
+ * @div should be in the range [1,63] to request a configuration, or 0 to
+ * inform that the configuration is no longer requested.
+ */
+int prcmu_config_clkout(u8 clkout, u8 source, u8 div)
+{
+ static int requests[2];
+ int r = 0;
+ unsigned long flags;
+ u32 val;
+ u32 bits;
+ u32 mask;
+ u32 div_mask;
+
+ BUG_ON(clkout > 1);
+ BUG_ON(div > 63);
+ BUG_ON((clkout == 0) && (source > PRCMU_CLKSRC_CLK009));
+
+ if (!div && !requests[clkout])
+ return -EINVAL;
+
+ switch (clkout) {
+ case 0:
+ div_mask = PRCM_CLKOCR_CLKODIV0_MASK;
+ mask = (PRCM_CLKOCR_CLKODIV0_MASK | PRCM_CLKOCR_CLKOSEL0_MASK);
+ bits = ((source << PRCM_CLKOCR_CLKOSEL0_SHIFT) |
+ (div << PRCM_CLKOCR_CLKODIV0_SHIFT));
+ break;
+ case 1:
+ div_mask = PRCM_CLKOCR_CLKODIV1_MASK;
+ mask = (PRCM_CLKOCR_CLKODIV1_MASK | PRCM_CLKOCR_CLKOSEL1_MASK |
+ PRCM_CLKOCR_CLK1TYPE);
+ bits = ((source << PRCM_CLKOCR_CLKOSEL1_SHIFT) |
+ (div << PRCM_CLKOCR_CLKODIV1_SHIFT));
+ break;
+ }
+ bits &= mask;
+
+ spin_lock_irqsave(&clkout_lock, flags);
+
+ val = readl(_PRCMU_BASE + PRCM_CLKOCR);
+ if (val & div_mask) {
+ if (div) {
+ if ((val & mask) != bits) {
+ r = -EBUSY;
+ goto unlock_and_return;
+ }
+ } else {
+ if ((val & mask & ~div_mask) != bits) {
+ r = -EINVAL;
+ goto unlock_and_return;
+ }
+ }
+ }
+ writel((bits | (val & ~mask)), (_PRCMU_BASE + PRCM_CLKOCR));
+ requests[clkout] += (div ? 1 : -1);
+
+unlock_and_return:
+ spin_unlock_irqrestore(&clkout_lock, flags);
+
+ return r;
+}
+
+int prcmu_set_power_state(u8 state, bool keep_ulp_clk, bool keep_ap_pll)
+{
+ unsigned long flags;
+
+ BUG_ON((state < PRCMU_AP_SLEEP) || (PRCMU_AP_DEEP_IDLE < state));
+
+ spin_lock_irqsave(&mb0_transfer.lock, flags);
+
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(0))
+ cpu_relax();
+
+ writeb(MB0H_POWER_STATE_TRANS, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB0));
+ writeb(state, (tcdm_base + PRCM_REQ_MB0_AP_POWER_STATE));
+ writeb((keep_ap_pll ? 1 : 0), (tcdm_base + PRCM_REQ_MB0_AP_PLL_STATE));
+ writeb((keep_ulp_clk ? 1 : 0),
+ (tcdm_base + PRCM_REQ_MB0_ULP_CLOCK_STATE));
+ writeb(0, (tcdm_base + PRCM_REQ_MB0_DO_NOT_WFI));
+ writel(MBOX_BIT(0), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+
+ spin_unlock_irqrestore(&mb0_transfer.lock, flags);
+
+ return 0;
+}
+
+/* This function should only be called while mb0_transfer.lock is held. */
+static void config_wakeups(void)
+{
+ const u8 header[2] = {
+ MB0H_CONFIG_WAKEUPS_EXE,
+ MB0H_CONFIG_WAKEUPS_SLEEP
+ };
+ static u32 last_dbb_events;
+ static u32 last_abb_events;
+ u32 dbb_events;
+ u32 abb_events;
+ unsigned int i;
+
+ dbb_events = mb0_transfer.req.dbb_irqs | mb0_transfer.req.dbb_wakeups;
+ dbb_events |= (WAKEUP_BIT_AC_WAKE_ACK | WAKEUP_BIT_AC_SLEEP_ACK);
+
+ abb_events = mb0_transfer.req.abb_events;
+
+ if ((dbb_events == last_dbb_events) && (abb_events == last_abb_events))
+ return;
+
+ for (i = 0; i < 2; i++) {
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(0))
+ cpu_relax();
+ writel(dbb_events, (tcdm_base + PRCM_REQ_MB0_WAKEUP_8500));
+ writel(abb_events, (tcdm_base + PRCM_REQ_MB0_WAKEUP_4500));
+ writeb(header[i], (tcdm_base + PRCM_MBOX_HEADER_REQ_MB0));
+ writel(MBOX_BIT(0), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ }
+ last_dbb_events = dbb_events;
+ last_abb_events = abb_events;
+}
+
+void prcmu_enable_wakeups(u32 wakeups)
+{
+ unsigned long flags;
+ u32 bits;
+ int i;
+
+ BUG_ON(wakeups != (wakeups & VALID_WAKEUPS));
+
+ for (i = 0, bits = 0; i < NUM_PRCMU_WAKEUP_INDICES; i++) {
+ if (wakeups & BIT(i))
+ bits |= prcmu_wakeup_bit[i];
+ }
+
+ spin_lock_irqsave(&mb0_transfer.lock, flags);
+
+ mb0_transfer.req.dbb_wakeups = bits;
+ config_wakeups();
+
+ spin_unlock_irqrestore(&mb0_transfer.lock, flags);
+}
+
+void prcmu_config_abb_event_readout(u32 abb_events)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&mb0_transfer.lock, flags);
+
+ mb0_transfer.req.abb_events = abb_events;
+ config_wakeups();
+
+ spin_unlock_irqrestore(&mb0_transfer.lock, flags);
+}
+
+void prcmu_get_abb_event_buffer(void __iomem **buf)
+{
+ if (readb(tcdm_base + PRCM_ACK_MB0_READ_POINTER) & 1)
+ *buf = (tcdm_base + PRCM_ACK_MB0_WAKEUP_1_4500);
+ else
+ *buf = (tcdm_base + PRCM_ACK_MB0_WAKEUP_0_4500);
+}
+
+/**
+ * prcmu_set_arm_opp - set the appropriate ARM OPP
+ * @opp: The new ARM operating point to which transition is to be made
+ * Returns: 0 on success, non-zero on failure
+ *
+ * This function sets the the operating point of the ARM.
+ */
+int prcmu_set_arm_opp(u8 opp)
+{
+ int r;
+
+ if (opp < ARM_NO_CHANGE || opp > ARM_EXTCLK)
+ return -EINVAL;
+
+ r = 0;
+
+ mutex_lock(&mb1_transfer.lock);
+
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
+ cpu_relax();
+
+ writeb(MB1H_ARM_APE_OPP, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB1));
+ writeb(opp, (tcdm_base + PRCM_REQ_MB1_ARM_OPP));
+ writeb(APE_NO_CHANGE, (tcdm_base + PRCM_REQ_MB1_APE_OPP));
+
+ writel(MBOX_BIT(1), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ wait_for_completion(&mb1_transfer.work);
+
+ if ((mb1_transfer.ack.header != MB1H_ARM_APE_OPP) ||
+ (mb1_transfer.ack.arm_opp != opp))
+ r = -EIO;
+
+ mutex_unlock(&mb1_transfer.lock);
+
+ return r;
+}
+
+/**
+ * prcmu_get_arm_opp - get the current ARM OPP
+ *
+ * Returns: the current ARM OPP
+ */
+int prcmu_get_arm_opp(void)
+{
+ return readb(tcdm_base + PRCM_ACK_MB1_CURRENT_ARM_OPP);
+}
+
+/**
+ * prcmu_get_ddr_opp - get the current DDR OPP
+ *
+ * Returns: the current DDR OPP
+ */
+int prcmu_get_ddr_opp(void)
+{
+ return readb(_PRCMU_BASE + PRCM_DDR_SUBSYS_APE_MINBW);
+}
+
+/**
+ * set_ddr_opp - set the appropriate DDR OPP
+ * @opp: The new DDR operating point to which transition is to be made
+ * Returns: 0 on success, non-zero on failure
+ *
+ * This function sets the operating point of the DDR.
+ */
+int prcmu_set_ddr_opp(u8 opp)
+{
+ if (opp < DDR_100_OPP || opp > DDR_25_OPP)
+ return -EINVAL;
+ /* Changing the DDR OPP can hang the hardware pre-v21 */
+ if (cpu_is_u8500v20_or_later() && !cpu_is_u8500v20())
+ writeb(opp, (_PRCMU_BASE + PRCM_DDR_SUBSYS_APE_MINBW));
+
+ return 0;
+}
+/**
+ * set_ape_opp - set the appropriate APE OPP
+ * @opp: The new APE operating point to which transition is to be made
+ * Returns: 0 on success, non-zero on failure
+ *
+ * This function sets the operating point of the APE.
+ */
+int prcmu_set_ape_opp(u8 opp)
+{
+ int r = 0;
+
+ mutex_lock(&mb1_transfer.lock);
+
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
+ cpu_relax();
+
+ writeb(MB1H_ARM_APE_OPP, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB1));
+ writeb(ARM_NO_CHANGE, (tcdm_base + PRCM_REQ_MB1_ARM_OPP));
+ writeb(opp, (tcdm_base + PRCM_REQ_MB1_APE_OPP));
+
+ writel(MBOX_BIT(1), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ wait_for_completion(&mb1_transfer.work);
+
+ if ((mb1_transfer.ack.header != MB1H_ARM_APE_OPP) ||
+ (mb1_transfer.ack.ape_opp != opp))
+ r = -EIO;
+
+ mutex_unlock(&mb1_transfer.lock);
+
+ return r;
+}
+
+/**
+ * prcmu_get_ape_opp - get the current APE OPP
+ *
+ * Returns: the current APE OPP
+ */
+int prcmu_get_ape_opp(void)
+{
+ return readb(tcdm_base + PRCM_ACK_MB1_CURRENT_APE_OPP);
+}
+
+/**
+ * prcmu_request_ape_opp_100_voltage - Request APE OPP 100% voltage
+ * @enable: true to request the higher voltage, false to drop a request.
+ *
+ * Calls to this function to enable and disable requests must be balanced.
+ */
+int prcmu_request_ape_opp_100_voltage(bool enable)
+{
+ int r = 0;
+ u8 header;
+ static unsigned int requests;
+
+ mutex_lock(&mb1_transfer.lock);
+
+ if (enable) {
+ if (0 != requests++)
+ goto unlock_and_return;
+ header = MB1H_REQUEST_APE_OPP_100_VOLT;
+ } else {
+ if (requests == 0) {
+ r = -EIO;
+ goto unlock_and_return;
+ } else if (1 != requests--) {
+ goto unlock_and_return;
+ }
+ header = MB1H_RELEASE_APE_OPP_100_VOLT;
+ }
+
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
+ cpu_relax();
+
+ writeb(header, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB1));
+
+ writel(MBOX_BIT(1), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ wait_for_completion(&mb1_transfer.work);
+
+ if ((mb1_transfer.ack.header != header) ||
+ ((mb1_transfer.ack.ape_voltage_status & BIT(0)) != 0))
+ r = -EIO;
+
+unlock_and_return:
+ mutex_unlock(&mb1_transfer.lock);
+
+ return r;
+}
+
+/**
+ * prcmu_release_usb_wakeup_state - release the state required by a USB wakeup
+ *
+ * This function releases the power state requirements of a USB wakeup.
+ */
+int prcmu_release_usb_wakeup_state(void)
+{
+ int r = 0;
+
+ mutex_lock(&mb1_transfer.lock);
+
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
+ cpu_relax();
+
+ writeb(MB1H_RELEASE_USB_WAKEUP,
+ (tcdm_base + PRCM_MBOX_HEADER_REQ_MB1));
+
+ writel(MBOX_BIT(1), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ wait_for_completion(&mb1_transfer.work);
+
+ if ((mb1_transfer.ack.header != MB1H_RELEASE_USB_WAKEUP) ||
+ ((mb1_transfer.ack.ape_voltage_status & BIT(0)) != 0))
+ r = -EIO;
+
+ mutex_unlock(&mb1_transfer.lock);
+
+ return r;
+}
+
+/**
+ * prcmu_set_epod - set the state of a EPOD (power domain)
+ * @epod_id: The EPOD to set
+ * @epod_state: The new EPOD state
+ *
+ * This function sets the state of a EPOD (power domain). It may not be called
+ * from interrupt context.
+ */
+int prcmu_set_epod(u16 epod_id, u8 epod_state)
+{
+ int r = 0;
+ bool ram_retention = false;
+ int i;
+
+ /* check argument */
+ BUG_ON(epod_id >= NUM_EPOD_ID);
+
+ /* set flag if retention is possible */
+ switch (epod_id) {
+ case EPOD_ID_SVAMMDSP:
+ case EPOD_ID_SIAMMDSP:
+ case EPOD_ID_ESRAM12:
+ case EPOD_ID_ESRAM34:
+ ram_retention = true;
+ break;
+ }
+
+ /* check argument */
+ BUG_ON(epod_state > EPOD_STATE_ON);
+ BUG_ON(epod_state == EPOD_STATE_RAMRET && !ram_retention);
+
+ /* get lock */
+ mutex_lock(&mb2_transfer.lock);
+
+ /* wait for mailbox */
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(2))
+ cpu_relax();
+
+ /* fill in mailbox */
+ for (i = 0; i < NUM_EPOD_ID; i++)
+ writeb(EPOD_STATE_NO_CHANGE, (tcdm_base + PRCM_REQ_MB2 + i));
+ writeb(epod_state, (tcdm_base + PRCM_REQ_MB2 + epod_id));
+
+ writeb(MB2H_DPS, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB2));
+
+ writel(MBOX_BIT(2), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+
+ /*
+ * The current firmware version does not handle errors correctly,
+ * and we cannot recover if there is an error.
+ * This is expected to change when the firmware is updated.
+ */
+ if (!wait_for_completion_timeout(&mb2_transfer.work,
+ msecs_to_jiffies(20000))) {
+ pr_err("prcmu: %s timed out (20 s) waiting for a reply.\n",
+ __func__);
+ r = -EIO;
+ goto unlock_and_return;
+ }
+
+ if (mb2_transfer.ack.status != HWACC_PWR_ST_OK)
+ r = -EIO;
+
+unlock_and_return:
+ mutex_unlock(&mb2_transfer.lock);
+ return r;
+}
+
+/**
+ * prcmu_configure_auto_pm - Configure autonomous power management.
+ * @sleep: Configuration for ApSleep.
+ * @idle: Configuration for ApIdle.
+ */
+void prcmu_configure_auto_pm(struct prcmu_auto_pm_config *sleep,
+ struct prcmu_auto_pm_config *idle)
+{
+ u32 sleep_cfg;
+ u32 idle_cfg;
+ unsigned long flags;
-#include <mach/hardware.h>
+ BUG_ON((sleep == NULL) || (idle == NULL));
-#include "db8500-prcmu-regs.h"
+ sleep_cfg = (sleep->sva_auto_pm_enable & 0xF);
+ sleep_cfg = ((sleep_cfg << 4) | (sleep->sia_auto_pm_enable & 0xF));
+ sleep_cfg = ((sleep_cfg << 8) | (sleep->sva_power_on & 0xFF));
+ sleep_cfg = ((sleep_cfg << 8) | (sleep->sia_power_on & 0xFF));
+ sleep_cfg = ((sleep_cfg << 4) | (sleep->sva_policy & 0xF));
+ sleep_cfg = ((sleep_cfg << 4) | (sleep->sia_policy & 0xF));
-/* Global var to runtime determine TCDM base for v2 or v1 */
-static __iomem void *tcdm_base;
+ idle_cfg = (idle->sva_auto_pm_enable & 0xF);
+ idle_cfg = ((idle_cfg << 4) | (idle->sia_auto_pm_enable & 0xF));
+ idle_cfg = ((idle_cfg << 8) | (idle->sva_power_on & 0xFF));
+ idle_cfg = ((idle_cfg << 8) | (idle->sia_power_on & 0xFF));
+ idle_cfg = ((idle_cfg << 4) | (idle->sva_policy & 0xF));
+ idle_cfg = ((idle_cfg << 4) | (idle->sia_policy & 0xF));
-#define _MBOX_HEADER (tcdm_base + 0xFE8)
-#define MBOX_HEADER_REQ_MB0 (_MBOX_HEADER + 0x0)
+ spin_lock_irqsave(&mb2_transfer.auto_pm_lock, flags);
-#define REQ_MB1 (tcdm_base + 0xFD0)
-#define REQ_MB5 (tcdm_base + 0xE44)
+ /*
+ * The autonomous power management configuration is done through
+ * fields in mailbox 2, but these fields are only used as shared
+ * variables - i.e. there is no need to send a message.
+ */
+ writel(sleep_cfg, (tcdm_base + PRCM_REQ_MB2_AUTO_PM_SLEEP));
+ writel(idle_cfg, (tcdm_base + PRCM_REQ_MB2_AUTO_PM_IDLE));
-#define REQ_MB1_ARMOPP (REQ_MB1 + 0x0)
-#define REQ_MB1_APEOPP (REQ_MB1 + 0x1)
-#define REQ_MB1_BOOSTOPP (REQ_MB1 + 0x2)
+ mb2_transfer.auto_pm_enabled =
+ ((sleep->sva_auto_pm_enable == PRCMU_AUTO_PM_ON) ||
+ (sleep->sia_auto_pm_enable == PRCMU_AUTO_PM_ON) ||
+ (idle->sva_auto_pm_enable == PRCMU_AUTO_PM_ON) ||
+ (idle->sia_auto_pm_enable == PRCMU_AUTO_PM_ON));
-#define ACK_MB1 (tcdm_base + 0xE04)
-#define ACK_MB5 (tcdm_base + 0xDF4)
+ spin_unlock_irqrestore(&mb2_transfer.auto_pm_lock, flags);
+}
+EXPORT_SYMBOL(prcmu_configure_auto_pm);
-#define ACK_MB1_CURR_ARMOPP (ACK_MB1 + 0x0)
-#define ACK_MB1_CURR_APEOPP (ACK_MB1 + 0x1)
+bool prcmu_is_auto_pm_enabled(void)
+{
+ return mb2_transfer.auto_pm_enabled;
+}
-#define REQ_MB5_I2C_SLAVE_OP (REQ_MB5)
-#define REQ_MB5_I2C_HW_BITS (REQ_MB5 + 1)
-#define REQ_MB5_I2C_REG (REQ_MB5 + 2)
-#define REQ_MB5_I2C_VAL (REQ_MB5 + 3)
+static int request_sysclk(bool enable)
+{
+ int r;
+ unsigned long flags;
-#define ACK_MB5_I2C_STATUS (ACK_MB5 + 1)
-#define ACK_MB5_I2C_VAL (ACK_MB5 + 3)
+ r = 0;
-#define PRCM_AVS_VARM_MAX_OPP (tcdm_base + 0x2E4)
-#define PRCM_AVS_ISMODEENABLE 7
-#define PRCM_AVS_ISMODEENABLE_MASK (1 << PRCM_AVS_ISMODEENABLE)
+ mutex_lock(&mb3_transfer.sysclk_lock);
-#define I2C_WRITE(slave) \
- (((slave) << 1) | (cpu_is_u8500v2() ? BIT(6) : 0))
-#define I2C_READ(slave) \
- (((slave) << 1) | (cpu_is_u8500v2() ? BIT(6) : 0) | BIT(0))
-#define I2C_STOP_EN BIT(3)
-
-enum mb1_h {
- MB1H_ARM_OPP = 1,
- MB1H_APE_OPP,
- MB1H_ARM_APE_OPP,
-};
+ spin_lock_irqsave(&mb3_transfer.lock, flags);
-static struct {
- struct mutex lock;
- struct completion work;
- struct {
- u8 arm_opp;
- u8 ape_opp;
- u8 arm_status;
- u8 ape_status;
- } ack;
-} mb1_transfer;
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(3))
+ cpu_relax();
-enum ack_mb5_status {
- I2C_WR_OK = 0x01,
- I2C_RD_OK = 0x02,
-};
+ writeb((enable ? ON : OFF), (tcdm_base + PRCM_REQ_MB3_SYSCLK_MGT));
-#define MBOX_BIT BIT
-#define NUM_MBOX 8
+ writeb(MB3H_SYSCLK, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB3));
+ writel(MBOX_BIT(3), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
-static struct {
- struct mutex lock;
- struct completion work;
- bool failed;
- struct {
- u8 status;
- u8 value;
- } ack;
-} mb5_transfer;
+ spin_unlock_irqrestore(&mb3_transfer.lock, flags);
+
+ /*
+ * The firmware only sends an ACK if we want to enable the
+ * SysClk, and it succeeds.
+ */
+ if (enable && !wait_for_completion_timeout(&mb3_transfer.sysclk_work,
+ msecs_to_jiffies(20000))) {
+ pr_err("prcmu: %s timed out (20 s) waiting for a reply.\n",
+ __func__);
+ r = -EIO;
+ }
+
+ mutex_unlock(&mb3_transfer.sysclk_lock);
+
+ return r;
+}
+
+static int request_timclk(bool enable)
+{
+ u32 val = (PRCM_TCR_DOZE_MODE | PRCM_TCR_TENSEL_MASK);
+
+ if (!enable)
+ val |= PRCM_TCR_STOP_TIMERS;
+ writel(val, (_PRCMU_BASE + PRCM_TCR));
+
+ return 0;
+}
+
+static int request_reg_clock(u8 clock, bool enable)
+{
+ u32 val;
+ unsigned long flags;
+
+ spin_lock_irqsave(&clk_mgt_lock, flags);
+
+ /* Grab the HW semaphore. */
+ while ((readl(_PRCMU_BASE + PRCM_SEM) & PRCM_SEM_PRCM_SEM) != 0)
+ cpu_relax();
+
+ val = readl(_PRCMU_BASE + clk_mgt[clock].offset);
+ if (enable) {
+ val |= (PRCM_CLK_MGT_CLKEN | clk_mgt[clock].pllsw);
+ } else {
+ clk_mgt[clock].pllsw = (val & PRCM_CLK_MGT_CLKPLLSW_MASK);
+ val &= ~(PRCM_CLK_MGT_CLKEN | PRCM_CLK_MGT_CLKPLLSW_MASK);
+ }
+ writel(val, (_PRCMU_BASE + clk_mgt[clock].offset));
+
+ /* Release the HW semaphore. */
+ writel(0, (_PRCMU_BASE + PRCM_SEM));
+
+ spin_unlock_irqrestore(&clk_mgt_lock, flags);
+
+ return 0;
+}
+
+/**
+ * prcmu_request_clock() - Request for a clock to be enabled or disabled.
+ * @clock: The clock for which the request is made.
+ * @enable: Whether the clock should be enabled (true) or disabled (false).
+ *
+ * This function should only be used by the clock implementation.
+ * Do not use it from any other place!
+ */
+int prcmu_request_clock(u8 clock, bool enable)
+{
+ if (clock < PRCMU_NUM_REG_CLOCKS)
+ return request_reg_clock(clock, enable);
+ else if (clock == PRCMU_TIMCLK)
+ return request_timclk(enable);
+ else if (clock == PRCMU_SYSCLK)
+ return request_sysclk(enable);
+ else
+ return -EINVAL;
+}
+
+int prcmu_config_esram0_deep_sleep(u8 state)
+{
+ if ((state > ESRAM0_DEEP_SLEEP_STATE_RET) ||
+ (state < ESRAM0_DEEP_SLEEP_STATE_OFF))
+ return -EINVAL;
+
+ mutex_lock(&mb4_transfer.lock);
+
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(4))
+ cpu_relax();
+
+ writeb(MB4H_MEM_ST, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB4));
+ writeb(((DDR_PWR_STATE_OFFHIGHLAT << 4) | DDR_PWR_STATE_ON),
+ (tcdm_base + PRCM_REQ_MB4_DDR_ST_AP_SLEEP_IDLE));
+ writeb(DDR_PWR_STATE_ON,
+ (tcdm_base + PRCM_REQ_MB4_DDR_ST_AP_DEEP_IDLE));
+ writeb(state, (tcdm_base + PRCM_REQ_MB4_ESRAM0_ST));
+
+ writel(MBOX_BIT(4), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ wait_for_completion(&mb4_transfer.work);
+
+ mutex_unlock(&mb4_transfer.lock);
+
+ return 0;
+}
+
+int prcmu_config_hotdog(u8 threshold)
+{
+ mutex_lock(&mb4_transfer.lock);
+
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(4))
+ cpu_relax();
+
+ writeb(threshold, (tcdm_base + PRCM_REQ_MB4_HOTDOG_THRESHOLD));
+ writeb(MB4H_HOTDOG, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB4));
+
+ writel(MBOX_BIT(4), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ wait_for_completion(&mb4_transfer.work);
+
+ mutex_unlock(&mb4_transfer.lock);
+
+ return 0;
+}
+
+int prcmu_config_hotmon(u8 low, u8 high)
+{
+ mutex_lock(&mb4_transfer.lock);
+
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(4))
+ cpu_relax();
+
+ writeb(low, (tcdm_base + PRCM_REQ_MB4_HOTMON_LOW));
+ writeb(high, (tcdm_base + PRCM_REQ_MB4_HOTMON_HIGH));
+ writeb((HOTMON_CONFIG_LOW | HOTMON_CONFIG_HIGH),
+ (tcdm_base + PRCM_REQ_MB4_HOTMON_CONFIG));
+ writeb(MB4H_HOTMON, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB4));
+
+ writel(MBOX_BIT(4), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ wait_for_completion(&mb4_transfer.work);
+
+ mutex_unlock(&mb4_transfer.lock);
+
+ return 0;
+}
+
+static int config_hot_period(u16 val)
+{
+ mutex_lock(&mb4_transfer.lock);
+
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(4))
+ cpu_relax();
+
+ writew(val, (tcdm_base + PRCM_REQ_MB4_HOT_PERIOD));
+ writeb(MB4H_HOT_PERIOD, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB4));
+
+ writel(MBOX_BIT(4), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ wait_for_completion(&mb4_transfer.work);
+
+ mutex_unlock(&mb4_transfer.lock);
+
+ return 0;
+}
+
+int prcmu_start_temp_sense(u16 cycles32k)
+{
+ if (cycles32k == 0xFFFF)
+ return -EINVAL;
+
+ return config_hot_period(cycles32k);
+}
+
+int prcmu_stop_temp_sense(void)
+{
+ return config_hot_period(0xFFFF);
+}
+
+/**
+ * prcmu_set_clock_divider() - Configure the clock divider.
+ * @clock: The clock for which the request is made.
+ * @divider: The clock divider. (< 32)
+ *
+ * This function should only be used by the clock implementation.
+ * Do not use it from any other place!
+ */
+int prcmu_set_clock_divider(u8 clock, u8 divider)
+{
+ u32 val;
+ unsigned long flags;
+
+ if ((clock >= PRCMU_NUM_REG_CLOCKS) || (divider < 1) || (31 < divider))
+ return -EINVAL;
+
+ spin_lock_irqsave(&clk_mgt_lock, flags);
+
+ /* Grab the HW semaphore. */
+ while ((readl(_PRCMU_BASE + PRCM_SEM) & PRCM_SEM_PRCM_SEM) != 0)
+ cpu_relax();
+
+ val = readl(_PRCMU_BASE + clk_mgt[clock].offset);
+ val &= ~(PRCM_CLK_MGT_CLKPLLDIV_MASK);
+ val |= (u32)divider;
+ writel(val, (_PRCMU_BASE + clk_mgt[clock].offset));
+
+ /* Release the HW semaphore. */
+ writel(0, (_PRCMU_BASE + PRCM_SEM));
+
+ spin_unlock_irqrestore(&clk_mgt_lock, flags);
+
+ return 0;
+}
/**
* prcmu_abb_read() - Read register value(s) from the ABB.
@@ -115,33 +1376,34 @@ int prcmu_abb_read(u8 slave, u8 reg, u8 *value, u8 size)
if (size != 1)
return -EINVAL;
- r = mutex_lock_interruptible(&mb5_transfer.lock);
- if (r)
- return r;
+ mutex_lock(&mb5_transfer.lock);
- while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(5))
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(5))
cpu_relax();
- writeb(I2C_READ(slave), REQ_MB5_I2C_SLAVE_OP);
- writeb(I2C_STOP_EN, REQ_MB5_I2C_HW_BITS);
- writeb(reg, REQ_MB5_I2C_REG);
+ writeb(PRCMU_I2C_READ(slave), (tcdm_base + PRCM_REQ_MB5_I2C_SLAVE_OP));
+ writeb(PRCMU_I2C_STOP_EN, (tcdm_base + PRCM_REQ_MB5_I2C_HW_BITS));
+ writeb(reg, (tcdm_base + PRCM_REQ_MB5_I2C_REG));
+ writeb(0, (tcdm_base + PRCM_REQ_MB5_I2C_VAL));
+
+ writel(MBOX_BIT(5), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
- writel(MBOX_BIT(5), PRCM_MBOX_CPU_SET);
if (!wait_for_completion_timeout(&mb5_transfer.work,
- msecs_to_jiffies(500))) {
- pr_err("prcmu: prcmu_abb_read timed out.\n");
+ msecs_to_jiffies(20000))) {
+ pr_err("prcmu: %s timed out (20 s) waiting for a reply.\n",
+ __func__);
r = -EIO;
- goto unlock_and_return;
+ } else {
+ r = ((mb5_transfer.ack.status == I2C_RD_OK) ? 0 : -EIO);
}
- r = ((mb5_transfer.ack.status == I2C_RD_OK) ? 0 : -EIO);
+
if (!r)
*value = mb5_transfer.ack.value;
-unlock_and_return:
mutex_unlock(&mb5_transfer.lock);
+
return r;
}
-EXPORT_SYMBOL(prcmu_abb_read);
/**
* prcmu_abb_write() - Write register value(s) to the ABB.
@@ -160,179 +1422,262 @@ int prcmu_abb_write(u8 slave, u8 reg, u8 *value, u8 size)
if (size != 1)
return -EINVAL;
- r = mutex_lock_interruptible(&mb5_transfer.lock);
- if (r)
- return r;
+ mutex_lock(&mb5_transfer.lock);
-
- while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(5))
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(5))
cpu_relax();
- writeb(I2C_WRITE(slave), REQ_MB5_I2C_SLAVE_OP);
- writeb(I2C_STOP_EN, REQ_MB5_I2C_HW_BITS);
- writeb(reg, REQ_MB5_I2C_REG);
- writeb(*value, REQ_MB5_I2C_VAL);
+ writeb(PRCMU_I2C_WRITE(slave), (tcdm_base + PRCM_REQ_MB5_I2C_SLAVE_OP));
+ writeb(PRCMU_I2C_STOP_EN, (tcdm_base + PRCM_REQ_MB5_I2C_HW_BITS));
+ writeb(reg, (tcdm_base + PRCM_REQ_MB5_I2C_REG));
+ writeb(*value, (tcdm_base + PRCM_REQ_MB5_I2C_VAL));
+
+ writel(MBOX_BIT(5), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
- writel(MBOX_BIT(5), PRCM_MBOX_CPU_SET);
if (!wait_for_completion_timeout(&mb5_transfer.work,
- msecs_to_jiffies(500))) {
- pr_err("prcmu: prcmu_abb_write timed out.\n");
+ msecs_to_jiffies(20000))) {
+ pr_err("prcmu: %s timed out (20 s) waiting for a reply.\n",
+ __func__);
r = -EIO;
- goto unlock_and_return;
+ } else {
+ r = ((mb5_transfer.ack.status == I2C_WR_OK) ? 0 : -EIO);
}
- r = ((mb5_transfer.ack.status == I2C_WR_OK) ? 0 : -EIO);
-unlock_and_return:
mutex_unlock(&mb5_transfer.lock);
+
return r;
}
-EXPORT_SYMBOL(prcmu_abb_write);
-static int set_ape_cpu_opps(u8 header, enum prcmu_ape_opp ape_opp,
- enum prcmu_cpu_opp cpu_opp)
+/**
+ * prcmu_ac_wake_req - should be called whenever ARM wants to wakeup Modem
+ */
+void prcmu_ac_wake_req(void)
{
- bool do_ape;
- bool do_arm;
- int err = 0;
+ u32 val;
- do_ape = ((header == MB1H_APE_OPP) || (header == MB1H_ARM_APE_OPP));
- do_arm = ((header == MB1H_ARM_OPP) || (header == MB1H_ARM_APE_OPP));
+ mutex_lock(&mb0_transfer.ac_wake_lock);
- mutex_lock(&mb1_transfer.lock);
+ val = readl(_PRCMU_BASE + PRCM_HOSTACCESS_REQ);
+ if (val & PRCM_HOSTACCESS_REQ_HOSTACCESS_REQ)
+ goto unlock_and_return;
- while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
- cpu_relax();
+ atomic_set(&ac_wake_req_state, 1);
- writeb(0, MBOX_HEADER_REQ_MB0);
- writeb(cpu_opp, REQ_MB1_ARMOPP);
- writeb(ape_opp, REQ_MB1_APEOPP);
- writeb(0, REQ_MB1_BOOSTOPP);
- writel(MBOX_BIT(1), PRCM_MBOX_CPU_SET);
- wait_for_completion(&mb1_transfer.work);
- if ((do_ape) && (mb1_transfer.ack.ape_status != 0))
- err = -EIO;
- if ((do_arm) && (mb1_transfer.ack.arm_status != 0))
- err = -EIO;
+ writel((val | PRCM_HOSTACCESS_REQ_HOSTACCESS_REQ),
+ (_PRCMU_BASE + PRCM_HOSTACCESS_REQ));
- mutex_unlock(&mb1_transfer.lock);
+ if (!wait_for_completion_timeout(&mb0_transfer.ac_wake_work,
+ msecs_to_jiffies(20000))) {
+ pr_err("prcmu: %s timed out (20 s) waiting for a reply.\n",
+ __func__);
+ }
- return err;
+unlock_and_return:
+ mutex_unlock(&mb0_transfer.ac_wake_lock);
}
/**
- * prcmu_set_ape_opp() - Set the OPP of the APE.
- * @opp: The OPP to set.
- *
- * This function sets the OPP of the APE.
+ * prcmu_ac_sleep_req - called when ARM no longer needs to talk to modem
*/
-int prcmu_set_ape_opp(enum prcmu_ape_opp opp)
+void prcmu_ac_sleep_req()
{
- return set_ape_cpu_opps(MB1H_APE_OPP, opp, APE_OPP_NO_CHANGE);
+ u32 val;
+
+ mutex_lock(&mb0_transfer.ac_wake_lock);
+
+ val = readl(_PRCMU_BASE + PRCM_HOSTACCESS_REQ);
+ if (!(val & PRCM_HOSTACCESS_REQ_HOSTACCESS_REQ))
+ goto unlock_and_return;
+
+ writel((val & ~PRCM_HOSTACCESS_REQ_HOSTACCESS_REQ),
+ (_PRCMU_BASE + PRCM_HOSTACCESS_REQ));
+
+ if (!wait_for_completion_timeout(&mb0_transfer.ac_wake_work,
+ msecs_to_jiffies(20000))) {
+ pr_err("prcmu: %s timed out (20 s) waiting for a reply.\n",
+ __func__);
+ }
+
+ atomic_set(&ac_wake_req_state, 0);
+
+unlock_and_return:
+ mutex_unlock(&mb0_transfer.ac_wake_lock);
}
-EXPORT_SYMBOL(prcmu_set_ape_opp);
-/**
- * prcmu_set_cpu_opp() - Set the OPP of the CPU.
- * @opp: The OPP to set.
- *
- * This function sets the OPP of the CPU.
- */
-int prcmu_set_cpu_opp(enum prcmu_cpu_opp opp)
+bool prcmu_is_ac_wake_requested(void)
{
- return set_ape_cpu_opps(MB1H_ARM_OPP, CPU_OPP_NO_CHANGE, opp);
+ return (atomic_read(&ac_wake_req_state) != 0);
}
-EXPORT_SYMBOL(prcmu_set_cpu_opp);
/**
- * prcmu_set_ape_cpu_opps() - Set the OPPs of the APE and the CPU.
- * @ape_opp: The APE OPP to set.
- * @cpu_opp: The CPU OPP to set.
+ * prcmu_system_reset - System reset
*
- * This function sets the OPPs of the APE and the CPU.
+ * Saves the reset reason code and then sets the APE_SOFRST register which
+ * fires interrupt to fw
*/
-int prcmu_set_ape_cpu_opps(enum prcmu_ape_opp ape_opp,
- enum prcmu_cpu_opp cpu_opp)
+void prcmu_system_reset(u16 reset_code)
{
- return set_ape_cpu_opps(MB1H_ARM_APE_OPP, ape_opp, cpu_opp);
+ writew(reset_code, (tcdm_base + PRCM_SW_RST_REASON));
+ writel(1, (_PRCMU_BASE + PRCM_APE_SOFTRST));
}
-EXPORT_SYMBOL(prcmu_set_ape_cpu_opps);
/**
- * prcmu_get_ape_opp() - Get the OPP of the APE.
- *
- * This function gets the OPP of the APE.
+ * prcmu_reset_modem - ask the PRCMU to reset modem
*/
-enum prcmu_ape_opp prcmu_get_ape_opp(void)
+void prcmu_modem_reset(void)
{
- return readb(ACK_MB1_CURR_APEOPP);
+ mutex_lock(&mb1_transfer.lock);
+
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
+ cpu_relax();
+
+ writeb(MB1H_RESET_MODEM, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB1));
+ writel(MBOX_BIT(1), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ wait_for_completion(&mb1_transfer.work);
+
+ /*
+ * No need to check return from PRCMU as modem should go in reset state
+ * This state is already managed by upper layer
+ */
+
+ mutex_unlock(&mb1_transfer.lock);
}
-EXPORT_SYMBOL(prcmu_get_ape_opp);
-/**
- * prcmu_get_cpu_opp() - Get the OPP of the CPU.
- *
- * This function gets the OPP of the CPU. The OPP is specified in %%.
- * PRCMU_OPP_EXT is a special OPP value, not specified in %%.
- */
-int prcmu_get_cpu_opp(void)
+static void ack_dbb_wakeup(void)
{
- return readb(ACK_MB1_CURR_ARMOPP);
+ unsigned long flags;
+
+ spin_lock_irqsave(&mb0_transfer.lock, flags);
+
+ while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(0))
+ cpu_relax();
+
+ writeb(MB0H_READ_WAKEUP_ACK, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB0));
+ writel(MBOX_BIT(0), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+
+ spin_unlock_irqrestore(&mb0_transfer.lock, flags);
}
-EXPORT_SYMBOL(prcmu_get_cpu_opp);
-bool prcmu_has_arm_maxopp(void)
+static inline void print_unknown_header_warning(u8 n, u8 header)
{
- return (readb(PRCM_AVS_VARM_MAX_OPP) & PRCM_AVS_ISMODEENABLE_MASK)
- == PRCM_AVS_ISMODEENABLE_MASK;
+ pr_warning("prcmu: Unknown message header (%d) in mailbox %d.\n",
+ header, n);
}
-static void read_mailbox_0(void)
+static bool read_mailbox_0(void)
{
- writel(MBOX_BIT(0), PRCM_ARM_IT1_CLEAR);
+ bool r;
+ u32 ev;
+ unsigned int n;
+ u8 header;
+
+ header = readb(tcdm_base + PRCM_MBOX_HEADER_ACK_MB0);
+ switch (header) {
+ case MB0H_WAKEUP_EXE:
+ case MB0H_WAKEUP_SLEEP:
+ if (readb(tcdm_base + PRCM_ACK_MB0_READ_POINTER) & 1)
+ ev = readl(tcdm_base + PRCM_ACK_MB0_WAKEUP_1_8500);
+ else
+ ev = readl(tcdm_base + PRCM_ACK_MB0_WAKEUP_0_8500);
+
+ if (ev & (WAKEUP_BIT_AC_WAKE_ACK | WAKEUP_BIT_AC_SLEEP_ACK))
+ complete(&mb0_transfer.ac_wake_work);
+ if (ev & WAKEUP_BIT_SYSCLK_OK)
+ complete(&mb3_transfer.sysclk_work);
+
+ ev &= mb0_transfer.req.dbb_irqs;
+
+ for (n = 0; n < NUM_PRCMU_WAKEUPS; n++) {
+ if (ev & prcmu_irq_bit[n])
+ generic_handle_irq(IRQ_PRCMU_BASE + n);
+ }
+ r = true;
+ break;
+ default:
+ print_unknown_header_warning(0, header);
+ r = false;
+ break;
+ }
+ writel(MBOX_BIT(0), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ return r;
}
-static void read_mailbox_1(void)
+static bool read_mailbox_1(void)
{
- mb1_transfer.ack.arm_opp = readb(ACK_MB1_CURR_ARMOPP);
- mb1_transfer.ack.ape_opp = readb(ACK_MB1_CURR_APEOPP);
+ mb1_transfer.ack.header = readb(tcdm_base + PRCM_MBOX_HEADER_REQ_MB1);
+ mb1_transfer.ack.arm_opp = readb(tcdm_base +
+ PRCM_ACK_MB1_CURRENT_ARM_OPP);
+ mb1_transfer.ack.ape_opp = readb(tcdm_base +
+ PRCM_ACK_MB1_CURRENT_APE_OPP);
+ mb1_transfer.ack.ape_voltage_status = readb(tcdm_base +
+ PRCM_ACK_MB1_APE_VOLTAGE_STATUS);
+ writel(MBOX_BIT(1), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
complete(&mb1_transfer.work);
- writel(MBOX_BIT(1), PRCM_ARM_IT1_CLEAR);
+ return false;
}
-static void read_mailbox_2(void)
+static bool read_mailbox_2(void)
{
- writel(MBOX_BIT(2), PRCM_ARM_IT1_CLEAR);
+ mb2_transfer.ack.status = readb(tcdm_base + PRCM_ACK_MB2_DPS_STATUS);
+ writel(MBOX_BIT(2), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ complete(&mb2_transfer.work);
+ return false;
}
-static void read_mailbox_3(void)
+static bool read_mailbox_3(void)
{
- writel(MBOX_BIT(3), PRCM_ARM_IT1_CLEAR);
+ writel(MBOX_BIT(3), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ return false;
}
-static void read_mailbox_4(void)
+static bool read_mailbox_4(void)
{
- writel(MBOX_BIT(4), PRCM_ARM_IT1_CLEAR);
+ u8 header;
+ bool do_complete = true;
+
+ header = readb(tcdm_base + PRCM_MBOX_HEADER_REQ_MB4);
+ switch (header) {
+ case MB4H_MEM_ST:
+ case MB4H_HOTDOG:
+ case MB4H_HOTMON:
+ case MB4H_HOT_PERIOD:
+ break;
+ default:
+ print_unknown_header_warning(4, header);
+ do_complete = false;
+ break;
+ }
+
+ writel(MBOX_BIT(4), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+
+ if (do_complete)
+ complete(&mb4_transfer.work);
+
+ return false;
}
-static void read_mailbox_5(void)
+static bool read_mailbox_5(void)
{
- mb5_transfer.ack.status = readb(ACK_MB5_I2C_STATUS);
- mb5_transfer.ack.value = readb(ACK_MB5_I2C_VAL);
+ mb5_transfer.ack.status = readb(tcdm_base + PRCM_ACK_MB5_I2C_STATUS);
+ mb5_transfer.ack.value = readb(tcdm_base + PRCM_ACK_MB5_I2C_VAL);
+ writel(MBOX_BIT(5), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
complete(&mb5_transfer.work);
- writel(MBOX_BIT(5), PRCM_ARM_IT1_CLEAR);
+ return false;
}
-static void read_mailbox_6(void)
+static bool read_mailbox_6(void)
{
- writel(MBOX_BIT(6), PRCM_ARM_IT1_CLEAR);
+ writel(MBOX_BIT(6), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ return false;
}
-static void read_mailbox_7(void)
+static bool read_mailbox_7(void)
{
- writel(MBOX_BIT(7), PRCM_ARM_IT1_CLEAR);
+ writel(MBOX_BIT(7), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ return false;
}
-static void (* const read_mailbox[NUM_MBOX])(void) = {
+static bool (* const read_mailbox[NUM_MB])(void) = {
read_mailbox_0,
read_mailbox_1,
read_mailbox_2,
@@ -347,49 +1692,199 @@ static irqreturn_t prcmu_irq_handler(int irq, void *data)
{
u32 bits;
u8 n;
+ irqreturn_t r;
- bits = (readl(PRCM_ARM_IT1_VAL) & (MBOX_BIT(NUM_MBOX) - 1));
+ bits = (readl(_PRCMU_BASE + PRCM_ARM_IT1_VAL) & ALL_MBOX_BITS);
if (unlikely(!bits))
return IRQ_NONE;
+ r = IRQ_HANDLED;
for (n = 0; bits; n++) {
if (bits & MBOX_BIT(n)) {
bits -= MBOX_BIT(n);
- read_mailbox[n]();
+ if (read_mailbox[n]())
+ r = IRQ_WAKE_THREAD;
}
}
+ return r;
+}
+
+static irqreturn_t prcmu_irq_thread_fn(int irq, void *data)
+{
+ ack_dbb_wakeup();
return IRQ_HANDLED;
}
+static void prcmu_mask_work(struct work_struct *work)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&mb0_transfer.lock, flags);
+
+ config_wakeups();
+
+ spin_unlock_irqrestore(&mb0_transfer.lock, flags);
+}
+
+static void prcmu_irq_mask(struct irq_data *d)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&mb0_transfer.dbb_irqs_lock, flags);
+
+ mb0_transfer.req.dbb_irqs &= ~prcmu_irq_bit[d->irq - IRQ_PRCMU_BASE];
+
+ spin_unlock_irqrestore(&mb0_transfer.dbb_irqs_lock, flags);
+
+ if (d->irq != IRQ_PRCMU_CA_SLEEP)
+ schedule_work(&mb0_transfer.mask_work);
+}
+
+static void prcmu_irq_unmask(struct irq_data *d)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&mb0_transfer.dbb_irqs_lock, flags);
+
+ mb0_transfer.req.dbb_irqs |= prcmu_irq_bit[d->irq - IRQ_PRCMU_BASE];
+
+ spin_unlock_irqrestore(&mb0_transfer.dbb_irqs_lock, flags);
+
+ if (d->irq != IRQ_PRCMU_CA_SLEEP)
+ schedule_work(&mb0_transfer.mask_work);
+}
+
+static void noop(struct irq_data *d)
+{
+}
+
+static struct irq_chip prcmu_irq_chip = {
+ .name = "prcmu",
+ .irq_disable = prcmu_irq_mask,
+ .irq_ack = noop,
+ .irq_mask = prcmu_irq_mask,
+ .irq_unmask = prcmu_irq_unmask,
+};
+
void __init prcmu_early_init(void)
{
- if (cpu_is_u8500v11() || cpu_is_u8500ed()) {
+ unsigned int i;
+
+ if (cpu_is_u8500v1()) {
tcdm_base = __io_address(U8500_PRCMU_TCDM_BASE_V1);
} else if (cpu_is_u8500v2()) {
+ void *tcpm_base = ioremap_nocache(U8500_PRCMU_TCPM_BASE, SZ_4K);
+
+ if (tcpm_base != NULL) {
+ int version;
+ version = readl(tcpm_base + PRCMU_FW_VERSION_OFFSET);
+ prcmu_version.project_number = version & 0xFF;
+ prcmu_version.api_version = (version >> 8) & 0xFF;
+ prcmu_version.func_version = (version >> 16) & 0xFF;
+ prcmu_version.errata = (version >> 24) & 0xFF;
+ pr_info("PRCMU firmware version %d.%d.%d\n",
+ (version >> 8) & 0xFF, (version >> 16) & 0xFF,
+ (version >> 24) & 0xFF);
+ iounmap(tcpm_base);
+ }
+
tcdm_base = __io_address(U8500_PRCMU_TCDM_BASE);
} else {
pr_err("prcmu: Unsupported chip version\n");
BUG();
}
-}
-
-static int __init prcmu_init(void)
-{
- if (cpu_is_u8500ed()) {
- pr_err("prcmu: Unsupported chip version\n");
- return 0;
- }
+ spin_lock_init(&mb0_transfer.lock);
+ spin_lock_init(&mb0_transfer.dbb_irqs_lock);
+ mutex_init(&mb0_transfer.ac_wake_lock);
+ init_completion(&mb0_transfer.ac_wake_work);
mutex_init(&mb1_transfer.lock);
init_completion(&mb1_transfer.work);
+ mutex_init(&mb2_transfer.lock);
+ init_completion(&mb2_transfer.work);
+ spin_lock_init(&mb2_transfer.auto_pm_lock);
+ spin_lock_init(&mb3_transfer.lock);
+ mutex_init(&mb3_transfer.sysclk_lock);
+ init_completion(&mb3_transfer.sysclk_work);
+ mutex_init(&mb4_transfer.lock);
+ init_completion(&mb4_transfer.work);
mutex_init(&mb5_transfer.lock);
init_completion(&mb5_transfer.work);
+ INIT_WORK(&mb0_transfer.mask_work, prcmu_mask_work);
+
+ /* Initalize irqs. */
+ for (i = 0; i < NUM_PRCMU_WAKEUPS; i++) {
+ unsigned int irq;
+
+ irq = IRQ_PRCMU_BASE + i;
+ irq_set_chip_and_handler(irq, &prcmu_irq_chip,
+ handle_simple_irq);
+ set_irq_flags(irq, IRQF_VALID);
+ }
+}
+
+static struct mfd_cell db8500_prcmu_devs[] = {
+ {
+ .name = "db8500-prcmu-regulators",
+ },
+ {
+ .name = "cpufreq-u8500",
+ },
+};
+
+/**
+ * prcmu_fw_init - arch init call for the Linux PRCMU fw init logic
+ *
+ */
+static int __init db8500_prcmu_probe(struct platform_device *pdev)
+{
+ int err = 0;
+
+ if (ux500_is_svp())
+ return -ENODEV;
+
/* Clean up the mailbox interrupts after pre-kernel code. */
- writel((MBOX_BIT(NUM_MBOX) - 1), PRCM_ARM_IT1_CLEAR);
+ writel(ALL_MBOX_BITS, (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+
+ err = request_threaded_irq(IRQ_DB8500_PRCMU1, prcmu_irq_handler,
+ prcmu_irq_thread_fn, IRQF_NO_SUSPEND, "prcmu", NULL);
+ if (err < 0) {
+ pr_err("prcmu: Failed to allocate IRQ_DB8500_PRCMU1.\n");
+ err = -EBUSY;
+ goto no_irq_return;
+ }
+
+ if (cpu_is_u8500v20_or_later())
+ prcmu_config_esram0_deep_sleep(ESRAM0_DEEP_SLEEP_STATE_RET);
+
+ err = mfd_add_devices(&pdev->dev, 0, db8500_prcmu_devs,
+ ARRAY_SIZE(db8500_prcmu_devs), NULL,
+ 0);
- return request_irq(IRQ_DB8500_PRCMU1, prcmu_irq_handler, 0,
- "prcmu", NULL);
+ if (err)
+ pr_err("prcmu: Failed to add subdevices\n");
+ else
+ pr_info("DB8500 PRCMU initialized\n");
+
+no_irq_return:
+ return err;
+}
+
+static struct platform_driver db8500_prcmu_driver = {
+ .driver = {
+ .name = "db8500-prcmu",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init db8500_prcmu_init(void)
+{
+ return platform_driver_probe(&db8500_prcmu_driver, db8500_prcmu_probe);
}
-arch_initcall(prcmu_init);
+arch_initcall(db8500_prcmu_init);
+
+MODULE_AUTHOR("Mattias Nilsson <mattias.i.nilsson@stericsson.com>");
+MODULE_DESCRIPTION("DB8500 PRCM Unit driver");
+MODULE_LICENSE("GPL v2");
@@ -2,57 +2,977 @@
* Copyright (C) STMicroelectronics 2009
* Copyright (C) ST-Ericsson SA 2010
*
- * Author: Sundar Iyer <sundar.iyer@stericsson.com>
- * Author: Martin Persson <martin.persson@stericsson.com>
- *
* License Terms: GNU General Public License v2
+ * Author: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
*
- * PRCM Unit definitions
+ * PRCMU f/w APIs
*/
+#ifndef __MFD_DB8500_PRCMU_H
+#define __MFD_DB8500_PRCMU_H
+
+#include <linux/interrupt.h>
+#include <linux/notifier.h>
-#ifndef __MACH_PRCMU_DEFS_H
-#define __MACH_PRCMU_DEFS_H
+/* This portion previously known as <mach/prcmu-fw-defs_v1.h> */
-enum prcmu_cpu_opp {
- CPU_OPP_INIT = 0x00,
- CPU_OPP_NO_CHANGE = 0x01,
- CPU_OPP_100 = 0x02,
- CPU_OPP_50 = 0x03,
- CPU_OPP_MAX = 0x04,
- CPU_OPP_EXT_CLK = 0x07
+/**
+ * enum state - ON/OFF state definition
+ * @OFF: State is ON
+ * @ON: State is OFF
+ *
+ */
+enum state {
+ OFF = 0x0,
+ ON = 0x1,
};
-enum prcmu_ape_opp {
- APE_OPP_NO_CHANGE = 0x00,
- APE_OPP_100 = 0x02,
- APE_OPP_50 = 0x03,
+
+/**
+ * enum ret_state - general purpose On/Off/Retention states
+ *
+ */
+enum ret_state {
+ OFFST = 0,
+ ONST = 1,
+ RETST = 2
};
-#endif /* __MACH_PRCMU_DEFS_H */
+/**
+ * enum clk_arm - ARM Cortex A9 clock schemes
+ * @A9_OFF:
+ * @A9_BOOT:
+ * @A9_OPPT1:
+ * @A9_OPPT2:
+ * @A9_EXTCLK:
+ */
+enum clk_arm {
+ A9_OFF,
+ A9_BOOT,
+ A9_OPPT1,
+ A9_OPPT2,
+ A9_EXTCLK
+};
-/*
- * Copyright (C) STMicroelectronics 2009
- * Copyright (C) ST-Ericsson SA 2010
+/**
+ * enum clk_gen - GEN#0/GEN#1 clock schemes
+ * @GEN_OFF:
+ * @GEN_BOOT:
+ * @GEN_OPPT1:
+ */
+enum clk_gen {
+ GEN_OFF,
+ GEN_BOOT,
+ GEN_OPPT1,
+};
+
+/* some information between arm and xp70 */
+
+/**
+ * enum romcode_write - Romcode message written by A9 AND read by XP70
+ * @RDY_2_DS: Value set when ApDeepSleep state can be executed by XP70
+ * @RDY_2_XP70_RST: Value set when 0x0F has been successfully polled by the
+ * romcode. The xp70 will go into self-reset
+ */
+enum romcode_write {
+ RDY_2_DS = 0x09,
+ RDY_2_XP70_RST = 0x10
+};
+
+/**
+ * enum romcode_read - Romcode message written by XP70 and read by A9
+ * @INIT: Init value when romcode field is not used
+ * @FS_2_DS: Value set when power state is going from ApExecute to
+ * ApDeepSleep
+ * @END_DS: Value set when ApDeepSleep power state is reached coming from
+ * ApExecute state
+ * @DS_TO_FS: Value set when power state is going from ApDeepSleep to
+ * ApExecute
+ * @END_FS: Value set when ApExecute power state is reached coming from
+ * ApDeepSleep state
+ * @SWR: Value set when power state is going to ApReset
+ * @END_SWR: Value set when the xp70 finished executing ApReset actions and
+ * waits for romcode acknowledgment to go to self-reset
+ */
+enum romcode_read {
+ INIT = 0x00,
+ FS_2_DS = 0x0A,
+ END_DS = 0x0B,
+ DS_TO_FS = 0x0C,
+ END_FS = 0x0D,
+ SWR = 0x0E,
+ END_SWR = 0x0F
+};
+
+/**
+ * enum ap_pwrst - current power states defined in PRCMU firmware
+ * @NO_PWRST: Current power state init
+ * @AP_BOOT: Current power state is apBoot
+ * @AP_EXECUTE: Current power state is apExecute
+ * @AP_DEEP_SLEEP: Current power state is apDeepSleep
+ * @AP_SLEEP: Current power state is apSleep
+ * @AP_IDLE: Current power state is apIdle
+ * @AP_RESET: Current power state is apReset
+ */
+enum ap_pwrst {
+ NO_PWRST = 0x00,
+ AP_BOOT = 0x01,
+ AP_EXECUTE = 0x02,
+ AP_DEEP_SLEEP = 0x03,
+ AP_SLEEP = 0x04,
+ AP_IDLE = 0x05,
+ AP_RESET = 0x06
+};
+
+/**
+ * enum ap_pwrst_trans - Transition states defined in PRCMU firmware
+ * @NO_TRANSITION: No power state transition
+ * @APEXECUTE_TO_APSLEEP: Power state transition from ApExecute to ApSleep
+ * @APIDLE_TO_APSLEEP: Power state transition from ApIdle to ApSleep
+ * @APBOOT_TO_APEXECUTE: Power state transition from ApBoot to ApExecute
+ * @APEXECUTE_TO_APDEEPSLEEP: Power state transition from ApExecute to
+ * ApDeepSleep
+ * @APEXECUTE_TO_APIDLE: Power state transition from ApExecute to ApIdle
+ */
+enum ap_pwrst_trans {
+ NO_TRANSITION = 0x00,
+ APEXECUTE_TO_APSLEEP = 0x01,
+ APIDLE_TO_APSLEEP = 0x02, /* To be removed */
+ PRCMU_AP_SLEEP = 0x01,
+ APBOOT_TO_APEXECUTE = 0x03,
+ APEXECUTE_TO_APDEEPSLEEP = 0x04, /* To be removed */
+ PRCMU_AP_DEEP_SLEEP = 0x04,
+ APEXECUTE_TO_APIDLE = 0x05, /* To be removed */
+ PRCMU_AP_IDLE = 0x05,
+ PRCMU_AP_DEEP_IDLE = 0x07,
+};
+
+/**
+ * enum ddr_pwrst - DDR power states definition
+ * @DDR_PWR_STATE_UNCHANGED: SDRAM and DDR controller state is unchanged
+ * @DDR_PWR_STATE_ON:
+ * @DDR_PWR_STATE_OFFLOWLAT:
+ * @DDR_PWR_STATE_OFFHIGHLAT:
+ */
+enum ddr_pwrst {
+ DDR_PWR_STATE_UNCHANGED = 0x00,
+ DDR_PWR_STATE_ON = 0x01,
+ DDR_PWR_STATE_OFFLOWLAT = 0x02,
+ DDR_PWR_STATE_OFFHIGHLAT = 0x03
+};
+
+/**
+ * enum arm_opp - ARM OPP states definition
+ * @ARM_OPP_INIT:
+ * @ARM_NO_CHANGE: The ARM operating point is unchanged
+ * @ARM_100_OPP: The new ARM operating point is arm100opp
+ * @ARM_50_OPP: The new ARM operating point is arm50opp
+ * @ARM_MAX_OPP: Operating point is "max" (more than 100)
+ * @ARM_MAX_FREQ100OPP: Set max opp if available, else 100
+ * @ARM_EXTCLK: The new ARM operating point is armExtClk
+ */
+enum arm_opp {
+ ARM_OPP_INIT = 0x00,
+ ARM_NO_CHANGE = 0x01,
+ ARM_100_OPP = 0x02,
+ ARM_50_OPP = 0x03,
+ ARM_MAX_OPP = 0x04,
+ ARM_MAX_FREQ100OPP = 0x05,
+ ARM_EXTCLK = 0x07
+};
+
+/**
+ * enum ape_opp - APE OPP states definition
+ * @APE_OPP_INIT:
+ * @APE_NO_CHANGE: The APE operating point is unchanged
+ * @APE_100_OPP: The new APE operating point is ape100opp
+ * @APE_50_OPP: 50%
+ */
+enum ape_opp {
+ APE_OPP_INIT = 0x00,
+ APE_NO_CHANGE = 0x01,
+ APE_100_OPP = 0x02,
+ APE_50_OPP = 0x03
+};
+
+/**
+ * enum hw_acc_state - State definition for hardware accelerator
+ * @HW_NO_CHANGE: The hardware accelerator state must remain unchanged
+ * @HW_OFF: The hardware accelerator must be switched off
+ * @HW_OFF_RAMRET: The hardware accelerator must be switched off with its
+ * internal RAM in retention
+ * @HW_ON: The hwa hardware accelerator hwa must be switched on
*
- * Author: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
- * Author: Sundar Iyer <sundar.iyer@stericsson.com>
- * Author: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
+ * NOTE! Deprecated, to be removed when all users switched over to use the
+ * regulator API.
+ */
+enum hw_acc_state {
+ HW_NO_CHANGE = 0x00,
+ HW_OFF = 0x01,
+ HW_OFF_RAMRET = 0x02,
+ HW_ON = 0x04
+};
+
+/**
+ * enum mbox_2_arm_stat - Status messages definition for mbox_arm
+ * @BOOT_TO_EXECUTEOK: The apBoot to apExecute state transition has been
+ * completed
+ * @DEEPSLEEPOK: The apExecute to apDeepSleep state transition has been
+ * completed
+ * @SLEEPOK: The apExecute to apSleep state transition has been completed
+ * @IDLEOK: The apExecute to apIdle state transition has been completed
+ * @SOFTRESETOK: The A9 watchdog/ SoftReset state has been completed
+ * @SOFTRESETGO : The A9 watchdog/SoftReset state is on going
+ * @BOOT_TO_EXECUTE: The apBoot to apExecute state transition is on going
+ * @EXECUTE_TO_DEEPSLEEP: The apExecute to apDeepSleep state transition is on
+ * going
+ * @DEEPSLEEP_TO_EXECUTE: The apDeepSleep to apExecute state transition is on
+ * going
+ * @DEEPSLEEP_TO_EXECUTEOK: The apDeepSleep to apExecute state transition has
+ * been completed
+ * @EXECUTE_TO_SLEEP: The apExecute to apSleep state transition is on going
+ * @SLEEP_TO_EXECUTE: The apSleep to apExecute state transition is on going
+ * @SLEEP_TO_EXECUTEOK: The apSleep to apExecute state transition has been
+ * completed
+ * @EXECUTE_TO_IDLE: The apExecute to apIdle state transition is on going
+ * @IDLE_TO_EXECUTE: The apIdle to apExecute state transition is on going
+ * @IDLE_TO_EXECUTEOK: The apIdle to apExecute state transition has been
+ * completed
+ * @INIT_STATUS: Status init
+ */
+enum ap_pwrsttr_status {
+ BOOT_TO_EXECUTEOK = 0xFF,
+ DEEPSLEEPOK = 0xFE,
+ SLEEPOK = 0xFD,
+ IDLEOK = 0xFC,
+ SOFTRESETOK = 0xFB,
+ SOFTRESETGO = 0xFA,
+ BOOT_TO_EXECUTE = 0xF9,
+ EXECUTE_TO_DEEPSLEEP = 0xF8,
+ DEEPSLEEP_TO_EXECUTE = 0xF7,
+ DEEPSLEEP_TO_EXECUTEOK = 0xF6,
+ EXECUTE_TO_SLEEP = 0xF5,
+ SLEEP_TO_EXECUTE = 0xF4,
+ SLEEP_TO_EXECUTEOK = 0xF3,
+ EXECUTE_TO_IDLE = 0xF2,
+ IDLE_TO_EXECUTE = 0xF1,
+ IDLE_TO_EXECUTEOK = 0xF0,
+ RDYTODS_RETURNTOEXE = 0xEF,
+ NORDYTODS_RETURNTOEXE = 0xEE,
+ EXETOSLEEP_RETURNTOEXE = 0xED,
+ EXETOIDLE_RETURNTOEXE = 0xEC,
+ INIT_STATUS = 0xEB,
+
+ /*error messages */
+ INITERROR = 0x00,
+ PLLARMLOCKP_ER = 0x01,
+ PLLDDRLOCKP_ER = 0x02,
+ PLLSOCLOCKP_ER = 0x03,
+ PLLSOCK1LOCKP_ER = 0x04,
+ ARMWFI_ER = 0x05,
+ SYSCLKOK_ER = 0x06,
+ I2C_NACK_DATA_ER = 0x07,
+ BOOT_ER = 0x08,
+ I2C_STATUS_ALWAYS_1 = 0x0A,
+ I2C_NACK_REG_ADDR_ER = 0x0B,
+ I2C_NACK_DATA0123_ER = 0x1B,
+ I2C_NACK_ADDR_ER = 0x1F,
+ CURAPPWRSTISNOT_BOOT = 0x20,
+ CURAPPWRSTISNOT_EXECUTE = 0x21,
+ CURAPPWRSTISNOT_SLEEPMODE = 0x22,
+ CURAPPWRSTISNOT_CORRECTFORIT10 = 0x23,
+ FIFO4500WUISNOT_WUPEVENT = 0x24,
+ PLL32KLOCKP_ER = 0x29,
+ DDRDEEPSLEEPOK_ER = 0x2A,
+ ROMCODEREADY_ER = 0x50,
+ WUPBEFOREDS = 0x51,
+ DDRCONFIG_ER = 0x52,
+ WUPBEFORESLEEP = 0x53,
+ WUPBEFOREIDLE = 0x54
+}; /* earlier called as mbox_2_arm_stat */
+
+/**
+ * enum dvfs_stat - DVFS status messages definition
+ * @DVFS_GO: A state transition DVFS is on going
+ * @DVFS_ARM100OPPOK: The state transition DVFS has been completed for 100OPP
+ * @DVFS_ARM50OPPOK: The state transition DVFS has been completed for 50OPP
+ * @DVFS_ARMEXTCLKOK: The state transition DVFS has been completed for EXTCLK
+ * @DVFS_NOCHGTCLKOK: The state transition DVFS has been completed for
+ * NOCHGCLK
+ * @DVFS_INITSTATUS: Value init
+ */
+enum dvfs_stat {
+ DVFS_GO = 0xFF,
+ DVFS_ARM100OPPOK = 0xFE,
+ DVFS_ARM50OPPOK = 0xFD,
+ DVFS_ARMEXTCLKOK = 0xFC,
+ DVFS_NOCHGTCLKOK = 0xFB,
+ DVFS_INITSTATUS = 0x00
+};
+
+/**
+ * enum sva_mmdsp_stat - SVA MMDSP status messages
+ * @SVA_MMDSP_GO: SVAMMDSP interrupt has happened
+ * @SVA_MMDSP_INIT: Status init
+ */
+enum sva_mmdsp_stat {
+ SVA_MMDSP_GO = 0xFF,
+ SVA_MMDSP_INIT = 0x00
+};
+
+/**
+ * enum sia_mmdsp_stat - SIA MMDSP status messages
+ * @SIA_MMDSP_GO: SIAMMDSP interrupt has happened
+ * @SIA_MMDSP_INIT: Status init
+ */
+enum sia_mmdsp_stat {
+ SIA_MMDSP_GO = 0xFF,
+ SIA_MMDSP_INIT = 0x00
+};
+
+/**
+ * enum mbox_to_arm_err - Error messages definition
+ * @INIT_ERR: Init value
+ * @PLLARMLOCKP_ERR: PLLARM has not been correctly locked in given time
+ * @PLLDDRLOCKP_ERR: PLLDDR has not been correctly locked in the given time
+ * @PLLSOC0LOCKP_ERR: PLLSOC0 has not been correctly locked in the given time
+ * @PLLSOC1LOCKP_ERR: PLLSOC1 has not been correctly locked in the given time
+ * @ARMWFI_ERR: The ARM WFI has not been correctly executed in the given time
+ * @SYSCLKOK_ERR: The SYSCLK is not available in the given time
+ * @BOOT_ERR: Romcode has not validated the XP70 self reset in the given time
+ * @ROMCODESAVECONTEXT: The Romcode didn.t correctly save it secure context
+ * @VARMHIGHSPEEDVALTO_ERR: The ARM high speed supply value transfered
+ * through I2C has not been correctly executed in the given time
+ * @VARMHIGHSPEEDACCESS_ERR: The command value of VarmHighSpeedVal transfered
+ * through I2C has not been correctly executed in the given time
+ * @VARMLOWSPEEDVALTO_ERR:The ARM low speed supply value transfered through
+ * I2C has not been correctly executed in the given time
+ * @VARMLOWSPEEDACCESS_ERR: The command value of VarmLowSpeedVal transfered
+ * through I2C has not been correctly executed in the given time
+ * @VARMRETENTIONVALTO_ERR: The ARM retention supply value transfered through
+ * I2C has not been correctly executed in the given time
+ * @VARMRETENTIONACCESS_ERR: The command value of VarmRetentionVal transfered
+ * through I2C has not been correctly executed in the given time
+ * @VAPEHIGHSPEEDVALTO_ERR: The APE highspeed supply value transfered through
+ * I2C has not been correctly executed in the given time
+ * @VSAFEHPVALTO_ERR: The SAFE high power supply value transfered through I2C
+ * has not been correctly executed in the given time
+ * @VMODSEL1VALTO_ERR: The MODEM sel1 supply value transfered through I2C has
+ * not been correctly executed in the given time
+ * @VMODSEL2VALTO_ERR: The MODEM sel2 supply value transfered through I2C has
+ * not been correctly executed in the given time
+ * @VARMOFFACCESS_ERR: The command value of Varm ON/OFF transfered through
+ * I2C has not been correctly executed in the given time
+ * @VAPEOFFACCESS_ERR: The command value of Vape ON/OFF transfered through
+ * I2C has not been correctly executed in the given time
+ * @VARMRETACCES_ERR: The command value of Varm retention ON/OFF transfered
+ * through I2C has not been correctly executed in the given time
+ * @CURAPPWRSTISNOTBOOT:Generated when Arm want to do power state transition
+ * ApBoot to ApExecute but the power current state is not Apboot
+ * @CURAPPWRSTISNOTEXECUTE: Generated when Arm want to do power state
+ * transition from ApExecute to others power state but the
+ * power current state is not ApExecute
+ * @CURAPPWRSTISNOTSLEEPMODE: Generated when wake up events are transmitted
+ * but the power current state is not ApDeepSleep/ApSleep/ApIdle
+ * @CURAPPWRSTISNOTCORRECTDBG: Generated when wake up events are transmitted
+ * but the power current state is not correct
+ * @ARMREGU1VALTO_ERR:The ArmRegu1 value transferred through I2C has not
+ * been correctly executed in the given time
+ * @ARMREGU2VALTO_ERR: The ArmRegu2 value transferred through I2C has not
+ * been correctly executed in the given time
+ * @VAPEREGUVALTO_ERR: The VApeRegu value transfered through I2C has not
+ * been correctly executed in the given time
+ * @VSMPS3REGUVALTO_ERR: The VSmps3Regu value transfered through I2C has not
+ * been correctly executed in the given time
+ * @VMODREGUVALTO_ERR: The VModemRegu value transfered through I2C has not
+ * been correctly executed in the given time
+ */
+enum mbox_to_arm_err {
+ INIT_ERR = 0x00,
+ PLLARMLOCKP_ERR = 0x01,
+ PLLDDRLOCKP_ERR = 0x02,
+ PLLSOC0LOCKP_ERR = 0x03,
+ PLLSOC1LOCKP_ERR = 0x04,
+ ARMWFI_ERR = 0x05,
+ SYSCLKOK_ERR = 0x06,
+ BOOT_ERR = 0x07,
+ ROMCODESAVECONTEXT = 0x08,
+ VARMHIGHSPEEDVALTO_ERR = 0x10,
+ VARMHIGHSPEEDACCESS_ERR = 0x11,
+ VARMLOWSPEEDVALTO_ERR = 0x12,
+ VARMLOWSPEEDACCESS_ERR = 0x13,
+ VARMRETENTIONVALTO_ERR = 0x14,
+ VARMRETENTIONACCESS_ERR = 0x15,
+ VAPEHIGHSPEEDVALTO_ERR = 0x16,
+ VSAFEHPVALTO_ERR = 0x17,
+ VMODSEL1VALTO_ERR = 0x18,
+ VMODSEL2VALTO_ERR = 0x19,
+ VARMOFFACCESS_ERR = 0x1A,
+ VAPEOFFACCESS_ERR = 0x1B,
+ VARMRETACCES_ERR = 0x1C,
+ CURAPPWRSTISNOTBOOT = 0x20,
+ CURAPPWRSTISNOTEXECUTE = 0x21,
+ CURAPPWRSTISNOTSLEEPMODE = 0x22,
+ CURAPPWRSTISNOTCORRECTDBG = 0x23,
+ ARMREGU1VALTO_ERR = 0x24,
+ ARMREGU2VALTO_ERR = 0x25,
+ VAPEREGUVALTO_ERR = 0x26,
+ VSMPS3REGUVALTO_ERR = 0x27,
+ VMODREGUVALTO_ERR = 0x28
+};
+
+enum hw_acc {
+ SVAMMDSP = 0,
+ SVAPIPE = 1,
+ SIAMMDSP = 2,
+ SIAPIPE = 3,
+ SGA = 4,
+ B2R2MCDE = 5,
+ ESRAM12 = 6,
+ ESRAM34 = 7,
+};
+
+enum cs_pwrmgt {
+ PWRDNCS0 = 0,
+ WKUPCS0 = 1,
+ PWRDNCS1 = 2,
+ WKUPCS1 = 3
+};
+
+/* Defs related to autonomous power management */
+
+/**
+ * enum sia_sva_pwr_policy - Power policy
+ * @NO_CHGT: No change
+ * @DSPOFF_HWPOFF:
+ * @DSPOFFRAMRET_HWPOFF:
+ * @DSPCLKOFF_HWPOFF:
+ * @DSPCLKOFF_HWPCLKOFF:
*
- * License Terms: GNU General Public License v2
+ */
+enum sia_sva_pwr_policy {
+ NO_CHGT = 0x0,
+ DSPOFF_HWPOFF = 0x1,
+ DSPOFFRAMRET_HWPOFF = 0x2,
+ DSPCLKOFF_HWPOFF = 0x3,
+ DSPCLKOFF_HWPCLKOFF = 0x4,
+};
+
+/**
+ * enum auto_enable - Auto Power enable
+ * @AUTO_OFF:
+ * @AUTO_ON:
+ *
+ */
+enum auto_enable {
+ AUTO_OFF = 0x0,
+ AUTO_ON = 0x1,
+};
+
+/* End of file previously known as prcmu-fw-defs_v1.h */
+
+/* PRCMU Wakeup defines */
+enum prcmu_wakeup_index {
+ PRCMU_WAKEUP_INDEX_RTC,
+ PRCMU_WAKEUP_INDEX_RTT0,
+ PRCMU_WAKEUP_INDEX_RTT1,
+ PRCMU_WAKEUP_INDEX_HSI0,
+ PRCMU_WAKEUP_INDEX_HSI1,
+ PRCMU_WAKEUP_INDEX_USB,
+ PRCMU_WAKEUP_INDEX_ABB,
+ PRCMU_WAKEUP_INDEX_ABB_FIFO,
+ PRCMU_WAKEUP_INDEX_ARM,
+ NUM_PRCMU_WAKEUP_INDICES
+};
+#define PRCMU_WAKEUP(_name) (BIT(PRCMU_WAKEUP_INDEX_##_name))
+
+/* PRCMU QoS APE OPP class */
+#define PRCMU_QOS_APE_OPP 1
+#define PRCMU_QOS_DDR_OPP 2
+#define PRCMU_QOS_DEFAULT_VALUE -1
+
+/**
+ * enum hw_acc_dev - enum for hw accelerators
+ * @HW_ACC_SVAMMDSP: for SVAMMDSP
+ * @HW_ACC_SVAPIPE: for SVAPIPE
+ * @HW_ACC_SIAMMDSP: for SIAMMDSP
+ * @HW_ACC_SIAPIPE: for SIAPIPE
+ * @HW_ACC_SGA: for SGA
+ * @HW_ACC_B2R2: for B2R2
+ * @HW_ACC_MCDE: for MCDE
+ * @HW_ACC_ESRAM1: for ESRAM1
+ * @HW_ACC_ESRAM2: for ESRAM2
+ * @HW_ACC_ESRAM3: for ESRAM3
+ * @HW_ACC_ESRAM4: for ESRAM4
+ * @NUM_HW_ACC: number of hardware accelerators
+ *
+ * Different hw accelerators which can be turned ON/
+ * OFF or put into retention (MMDSPs and ESRAMs).
+ * Used with EPOD API.
*
- * PRCM Unit f/w API
+ * NOTE! Deprecated, to be removed when all users switched over to use the
+ * regulator API.
+ */
+enum hw_acc_dev {
+ HW_ACC_SVAMMDSP,
+ HW_ACC_SVAPIPE,
+ HW_ACC_SIAMMDSP,
+ HW_ACC_SIAPIPE,
+ HW_ACC_SGA,
+ HW_ACC_B2R2,
+ HW_ACC_MCDE,
+ HW_ACC_ESRAM1,
+ HW_ACC_ESRAM2,
+ HW_ACC_ESRAM3,
+ HW_ACC_ESRAM4,
+ NUM_HW_ACC
+};
+
+/*
+ * Ids for all EPODs (power domains)
+ * - EPOD_ID_SVAMMDSP: power domain for SVA MMDSP
+ * - EPOD_ID_SVAPIPE: power domain for SVA pipe
+ * - EPOD_ID_SIAMMDSP: power domain for SIA MMDSP
+ * - EPOD_ID_SIAPIPE: power domain for SIA pipe
+ * - EPOD_ID_SGA: power domain for SGA
+ * - EPOD_ID_B2R2_MCDE: power domain for B2R2 and MCDE
+ * - EPOD_ID_ESRAM12: power domain for ESRAM 1 and 2
+ * - EPOD_ID_ESRAM34: power domain for ESRAM 3 and 4
+ * - NUM_EPOD_ID: number of power domains
+ */
+#define EPOD_ID_SVAMMDSP 0
+#define EPOD_ID_SVAPIPE 1
+#define EPOD_ID_SIAMMDSP 2
+#define EPOD_ID_SIAPIPE 3
+#define EPOD_ID_SGA 4
+#define EPOD_ID_B2R2_MCDE 5
+#define EPOD_ID_ESRAM12 6
+#define EPOD_ID_ESRAM34 7
+#define NUM_EPOD_ID 8
+
+/*
+ * state definition for EPOD (power domain)
+ * - EPOD_STATE_NO_CHANGE: The EPOD should remain unchanged
+ * - EPOD_STATE_OFF: The EPOD is switched off
+ * - EPOD_STATE_RAMRET: The EPOD is switched off with its internal RAM in
+ * retention
+ * - EPOD_STATE_ON_CLK_OFF: The EPOD is switched on, clock is still off
+ * - EPOD_STATE_ON: Same as above, but with clock enabled
*/
-#ifndef __MACH_PRCMU_H
-#define __MACH_PRCMU_H
+#define EPOD_STATE_NO_CHANGE 0x00
+#define EPOD_STATE_OFF 0x01
+#define EPOD_STATE_RAMRET 0x02
+#define EPOD_STATE_ON_CLK_OFF 0x03
+#define EPOD_STATE_ON 0x04
+/*
+ * CLKOUT sources
+ */
+#define PRCMU_CLKSRC_CLK38M 0x00
+#define PRCMU_CLKSRC_ACLK 0x01
+#define PRCMU_CLKSRC_SYSCLK 0x02
+#define PRCMU_CLKSRC_LCDCLK 0x03
+#define PRCMU_CLKSRC_SDMMCCLK 0x04
+#define PRCMU_CLKSRC_TVCLK 0x05
+#define PRCMU_CLKSRC_TIMCLK 0x06
+#define PRCMU_CLKSRC_CLK009 0x07
+/* These are only valid for CLKOUT1: */
+#define PRCMU_CLKSRC_SIAMMDSPCLK 0x40
+#define PRCMU_CLKSRC_I2CCLK 0x41
+#define PRCMU_CLKSRC_MSP02CLK 0x42
+#define PRCMU_CLKSRC_ARMPLL_OBSCLK 0x43
+#define PRCMU_CLKSRC_HSIRXCLK 0x44
+#define PRCMU_CLKSRC_HSITXCLK 0x45
+#define PRCMU_CLKSRC_ARMCLKFIX 0x46
+#define PRCMU_CLKSRC_HDMICLK 0x47
+
+/*
+ * Definitions for autonomous power management configuration.
+ */
+
+#define PRCMU_AUTO_PM_OFF 0
+#define PRCMU_AUTO_PM_ON 1
+
+#define PRCMU_AUTO_PM_POWER_ON_HSEM BIT(0)
+#define PRCMU_AUTO_PM_POWER_ON_ABB_FIFO_IT BIT(1)
+
+enum prcmu_auto_pm_policy {
+ PRCMU_AUTO_PM_POLICY_NO_CHANGE,
+ PRCMU_AUTO_PM_POLICY_DSP_OFF_HWP_OFF,
+ PRCMU_AUTO_PM_POLICY_DSP_OFF_RAMRET_HWP_OFF,
+ PRCMU_AUTO_PM_POLICY_DSP_CLK_OFF_HWP_OFF,
+ PRCMU_AUTO_PM_POLICY_DSP_CLK_OFF_HWP_CLK_OFF,
+};
+
+/**
+ * struct prcmu_auto_pm_config - Autonomous power management configuration.
+ * @sia_auto_pm_enable: SIA autonomous pm enable. (PRCMU_AUTO_PM_{OFF,ON})
+ * @sia_power_on: SIA power ON enable. (PRCMU_AUTO_PM_POWER_ON_* bitmask)
+ * @sia_policy: SIA power policy. (enum prcmu_auto_pm_policy)
+ * @sva_auto_pm_enable: SVA autonomous pm enable. (PRCMU_AUTO_PM_{OFF,ON})
+ * @sva_power_on: SVA power ON enable. (PRCMU_AUTO_PM_POWER_ON_* bitmask)
+ * @sva_policy: SVA power policy. (enum prcmu_auto_pm_policy)
+ */
+struct prcmu_auto_pm_config {
+ u8 sia_auto_pm_enable;
+ u8 sia_power_on;
+ u8 sia_policy;
+ u8 sva_auto_pm_enable;
+ u8 sva_power_on;
+ u8 sva_policy;
+};
+
+/**
+ * enum ddr_opp - DDR OPP states definition
+ * @DDR_100_OPP: The new DDR operating point is ddr100opp
+ * @DDR_50_OPP: The new DDR operating point is ddr50opp
+ * @DDR_25_OPP: The new DDR operating point is ddr25opp
+ */
+enum ddr_opp {
+ DDR_100_OPP = 0x00,
+ DDR_50_OPP = 0x01,
+ DDR_25_OPP = 0x02,
+};
+
+/*
+ * Clock identifiers.
+ */
+enum prcmu_clock {
+ PRCMU_SGACLK,
+ PRCMU_UARTCLK,
+ PRCMU_MSP02CLK,
+ PRCMU_MSP1CLK,
+ PRCMU_I2CCLK,
+ PRCMU_SDMMCCLK,
+ PRCMU_SLIMCLK,
+ PRCMU_PER1CLK,
+ PRCMU_PER2CLK,
+ PRCMU_PER3CLK,
+ PRCMU_PER5CLK,
+ PRCMU_PER6CLK,
+ PRCMU_PER7CLK,
+ PRCMU_LCDCLK,
+ PRCMU_BMLCLK,
+ PRCMU_HSITXCLK,
+ PRCMU_HSIRXCLK,
+ PRCMU_HDMICLK,
+ PRCMU_APEATCLK,
+ PRCMU_APETRACECLK,
+ PRCMU_MCDECLK,
+ PRCMU_IPI2CCLK,
+ PRCMU_DSIALTCLK,
+ PRCMU_DMACLK,
+ PRCMU_B2R2CLK,
+ PRCMU_TVCLK,
+ PRCMU_SSPCLK,
+ PRCMU_RNGCLK,
+ PRCMU_UICCCLK,
+ PRCMU_NUM_REG_CLOCKS,
+ PRCMU_SYSCLK = PRCMU_NUM_REG_CLOCKS,
+ PRCMU_TIMCLK,
+};
+
+/*
+ * Definitions for controlling ESRAM0 in deep sleep.
+ */
+#define ESRAM0_DEEP_SLEEP_STATE_OFF 1
+#define ESRAM0_DEEP_SLEEP_STATE_RET 2
+
+#ifdef CONFIG_MFD_DB8500_PRCMU
void __init prcmu_early_init(void);
+int prcmu_set_display_clocks(void);
+int prcmu_disable_dsipll(void);
+int prcmu_enable_dsipll(void);
+#else
+static inline void __init prcmu_early_init(void) {}
+#endif
+
+#ifdef CONFIG_MFD_DB8500_PRCMU
+
+int prcmu_set_rc_a2p(enum romcode_write);
+enum romcode_read prcmu_get_rc_p2a(void);
+enum ap_pwrst prcmu_get_xp70_current_state(void);
+int prcmu_set_power_state(u8 state, bool keep_ulp_clk, bool keep_ap_pll);
+
+void prcmu_enable_wakeups(u32 wakeups);
+static inline void prcmu_disable_wakeups(void)
+{
+ prcmu_enable_wakeups(0);
+}
+
+void prcmu_config_abb_event_readout(u32 abb_events);
+void prcmu_get_abb_event_buffer(void __iomem **buf);
+int prcmu_set_arm_opp(u8 opp);
+int prcmu_get_arm_opp(void);
+bool prcmu_has_arm_maxopp(void);
+bool prcmu_is_u8400(void);
+int prcmu_set_ape_opp(u8 opp);
+int prcmu_get_ape_opp(void);
+int prcmu_request_ape_opp_100_voltage(bool enable);
+int prcmu_release_usb_wakeup_state(void);
+int prcmu_set_ddr_opp(u8 opp);
+int prcmu_get_ddr_opp(void);
+unsigned long prcmu_qos_get_cpufreq_opp_delay(void);
+void prcmu_qos_set_cpufreq_opp_delay(unsigned long);
+/* NOTE! Use regulator framework instead */
+int prcmu_set_hwacc(u16 hw_acc_dev, u8 state);
+int prcmu_set_epod(u16 epod_id, u8 epod_state);
+void prcmu_configure_auto_pm(struct prcmu_auto_pm_config *sleep,
+ struct prcmu_auto_pm_config *idle);
+bool prcmu_is_auto_pm_enabled(void);
+
+int prcmu_config_clkout(u8 clkout, u8 source, u8 div);
+int prcmu_request_clock(u8 clock, bool enable);
+int prcmu_set_clock_divider(u8 clock, u8 divider);
+int prcmu_config_esram0_deep_sleep(u8 state);
+int prcmu_config_hotdog(u8 threshold);
+int prcmu_config_hotmon(u8 low, u8 high);
+int prcmu_start_temp_sense(u16 cycles32k);
+int prcmu_stop_temp_sense(void);
int prcmu_abb_read(u8 slave, u8 reg, u8 *value, u8 size);
int prcmu_abb_write(u8 slave, u8 reg, u8 *value, u8 size);
-int prcmu_set_ape_opp(enum prcmu_ape_opp opp);
-int prcmu_set_cpu_opp(enum prcmu_cpu_opp opp);
-int prcmu_set_ape_cpu_opps(enum prcmu_ape_opp ape_opp,
- enum prcmu_cpu_opp cpu_opp);
-enum prcmu_ape_opp prcmu_get_ape_opp(void);
-int prcmu_get_cpu_opp(void);
-bool prcmu_has_arm_maxopp(void);
-#endif /* __MACH_PRCMU_H */
+void prcmu_ac_wake_req(void);
+void prcmu_ac_sleep_req(void);
+void prcmu_system_reset(u16 reset_code);
+void prcmu_modem_reset(void);
+bool prcmu_is_ac_wake_requested(void);
+void prcmu_enable_spi2(void);
+void prcmu_disable_spi2(void);
+
+#else /* !CONFIG_MFD_DB8500_PRCMU */
+
+static inline int prcmu_set_rc_a2p(enum romcode_write code)
+{
+ return 0;
+}
+
+static inline enum romcode_read prcmu_get_rc_p2a(void)
+{
+ return INIT;
+}
+
+static inline enum ap_pwrst prcmu_get_xp70_current_state(void)
+{
+ return AP_EXECUTE;
+}
+
+static inline int prcmu_set_power_state(u8 state, bool keep_ulp_clk,
+ bool keep_ap_pll)
+{
+ return 0;
+}
+
+static inline void prcmu_enable_wakeups(u32 wakeups) {}
+
+static inline void prcmu_disable_wakeups(void) {}
+
+static inline void prcmu_config_abb_event_readout(u32 abb_events) {}
+
+static inline int prcmu_set_arm_opp(u8 opp)
+{
+ return 0;
+}
+
+static inline int prcmu_get_arm_opp(void)
+{
+ return ARM_100_OPP;
+}
+
+static bool prcmu_has_arm_maxopp(void)
+{
+ return false;
+}
+
+static bool prcmu_is_u8400(void)
+{
+ return false;
+}
+
+static inline int prcmu_set_ape_opp(u8 opp)
+{
+ return 0;
+}
+
+static inline int prcmu_get_ape_opp(void)
+{
+ return APE_100_OPP;
+}
+
+static inline int prcmu_request_ape_opp_100_voltage(bool enable)
+{
+ return 0;
+}
+
+static inline int prcmu_release_usb_wakeup_state(void)
+{
+ return 0;
+}
+
+static inline int prcmu_set_ddr_opp(u8 opp)
+{
+ return 0;
+}
+
+static inline int prcmu_get_ddr_opp(void)
+{
+ return DDR_100_OPP;
+}
+
+static inline unsigned long prcmu_qos_get_cpufreq_opp_delay(void)
+{
+ return 0;
+}
+
+static inline void prcmu_qos_set_cpufreq_opp_delay(unsigned long n) {}
+
+static inline int prcmu_set_hwacc(u16 hw_acc_dev, u8 state)
+{
+ return 0;
+}
+
+static inline void prcmu_configure_auto_pm(struct prcmu_auto_pm_config *sleep,
+ struct prcmu_auto_pm_config *idle)
+{
+}
+
+static inline bool prcmu_is_auto_pm_enabled(void)
+{
+ return false;
+}
+
+static inline int prcmu_config_clkout(u8 clkout, u8 source, u8 div)
+{
+ return 0;
+}
+
+static inline int prcmu_request_clock(u8 clock, bool enable)
+{
+ return 0;
+}
+
+static inline int prcmu_set_clock_divider(u8 clock, u8 divider)
+{
+ return 0;
+}
+
+int prcmu_config_esram0_deep_sleep(u8 state)
+{
+ return 0;
+}
+
+static inline int prcmu_config_hotdog(u8 threshold)
+{
+ return 0;
+}
+
+static inline int prcmu_config_hotmon(u8 low, u8 high)
+{
+ return 0;
+}
+
+static inline int prcmu_start_temp_sense(u16 cycles32k)
+{
+ return 0;
+}
+
+static inline int prcmu_stop_temp_sense(void)
+{
+ return 0;
+}
+
+static inline int prcmu_abb_read(u8 slave, u8 reg, u8 *value, u8 size)
+{
+ return -ENOSYS;
+}
+
+static inline int prcmu_abb_write(u8 slave, u8 reg, u8 *value, u8 size)
+{
+ return -ENOSYS;
+}
+
+static inline void prcmu_ac_wake_req(void) {}
+
+static inline void prcmu_ac_sleep_req(void) {}
+
+static inline void prcmu_system_reset(u16 reset_code) {}
+
+static inline void prcmu_modem_reset(void) {}
+
+static inline bool prcmu_is_ac_wake_requested(void)
+{
+ return false;
+}
+
+#ifndef CONFIG_UX500_SOC_DB5500
+static inline int prcmu_set_display_clocks(void)
+{
+ return 0;
+}
+
+static inline int prcmu_disable_dsipll(void)
+{
+ return 0;
+}
+
+static inline int prcmu_enable_dsipll(void)
+{
+ return 0;
+}
+#endif
+
+static inline int prcmu_enable_spi2(void)
+{
+ return 0;
+}
+
+static inline int prcmu_disable_spi2(void)
+{
+ return 0;
+}
+
+#endif /* !CONFIG_MFD_DB8500_PRCMU */
+
+#ifdef CONFIG_UX500_PRCMU_QOS_POWER
+int prcmu_qos_requirement(int pm_qos_class);
+int prcmu_qos_add_requirement(int pm_qos_class, char *name, s32 value);
+int prcmu_qos_update_requirement(int pm_qos_class, char *name, s32 new_value);
+void prcmu_qos_remove_requirement(int pm_qos_class, char *name);
+int prcmu_qos_add_notifier(int prcmu_qos_class,
+ struct notifier_block *notifier);
+int prcmu_qos_remove_notifier(int prcmu_qos_class,
+ struct notifier_block *notifier);
+#else
+static inline int prcmu_qos_requirement(int prcmu_qos_class)
+{
+ return 0;
+}
+
+static inline int prcmu_qos_add_requirement(int prcmu_qos_class,
+ char *name, s32 value)
+{
+ return 0;
+}
+
+static inline int prcmu_qos_update_requirement(int prcmu_qos_class,
+ char *name, s32 new_value)
+{
+ return 0;
+}
+
+static inline void prcmu_qos_remove_requirement(int prcmu_qos_class, char *name)
+{
+}
+
+static inline int prcmu_qos_add_notifier(int prcmu_qos_class,
+ struct notifier_block *notifier)
+{
+ return 0;
+}
+static inline int prcmu_qos_remove_notifier(int prcmu_qos_class,
+ struct notifier_block *notifier)
+{
+ return 0;
+}
+
+#endif
+
+#endif /* __MFD_DB8500_PRCMU_H */