diff mbox

EXYNOS: SPL: Add a custom spi copy function

Message ID 1364380100-9983-1-git-send-email-rajeshwari.s@samsung.com
State New
Headers show

Commit Message

Rajeshwari Shinde March 27, 2013, 10:28 a.m. UTC 
This CL implements a custom spi_copy funtion to copy u-boot from SF to
RAM. This is faster then iROM spi_copy funtion as this runs spi at 50Mhz
and also in WORD mode of operation.

Changed a printf in pimux.c to debug just to avoid the the compilation
error in SPL.
Removed the enum for boot mode from spl_boot.c as it was already define in spl.h

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signe-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
---
 arch/arm/cpu/armv7/exynos/pinmux.c     |    2 +-
 arch/arm/include/asm/arch-exynos/spi.h |    2 +
 board/samsung/smdk5250/spl_boot.c      |  126 +++++++++++++++++++++++++++++---
 include/configs/exynos5250-dt.h        |    3 +
 spl/Makefile                           |    4 +
 5 files changed, 124 insertions(+), 13 deletions(-)

Comments

Simon Glass May 11, 2013, 3:16 p.m. UTC | #1 
Hi Rajeshwari,

On Wed, Mar 27, 2013 at 4:28 AM, Rajeshwari Shinde
<rajeshwari.s@samsung.com> wrote:
> This CL implements a custom spi_copy funtion to copy u-boot from SF to
> RAM. This is faster then iROM spi_copy funtion as this runs spi at 50Mhz
> and also in WORD mode of operation.
>
> Changed a printf in pimux.c to debug just to avoid the the compilation
> error in SPL.
> Removed the enum for boot mode from spl_boot.c as it was already define in spl.h
>
> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
> Signe-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>

This now conflicts with the MMC series. I have an updated patch so
will post it as a v2 to this one. That way the MMC patches can be
applied first, then all your SPI patches.

Regards,
Simon
diff mbox

Patch

diff --git a/arch/arm/cpu/armv7/exynos/pinmux.c b/arch/arm/cpu/armv7/exynos/pinmux.c
index 1e7d14c..445f6fa 100644
--- a/arch/arm/cpu/armv7/exynos/pinmux.c
+++ b/arch/arm/cpu/armv7/exynos/pinmux.c
@@ -399,7 +399,7 @@  static int exynos4_pinmux_config(int peripheral, int flags)
 	case PERIPH_ID_SDMMC1:
 	case PERIPH_ID_SDMMC3:
 	case PERIPH_ID_SDMMC4:
-		printf("SDMMC device %d not implemented\n", peripheral);
+		debug("SDMMC device %d not implemented\n", peripheral);
 		return -1;
 	default:
 		debug("%s: invalid peripheral %d", __func__, peripheral);
diff --git a/arch/arm/include/asm/arch-exynos/spi.h b/arch/arm/include/asm/arch-exynos/spi.h
index e67ad27..3430ac1 100644
--- a/arch/arm/include/asm/arch-exynos/spi.h
+++ b/arch/arm/include/asm/arch-exynos/spi.h
@@ -43,6 +43,8 @@  struct exynos_spi {
 
 #define SPI_TIMEOUT_MS		10
 
+#define SF_READ_DATA_CMD	0x3
+
 /* SPI_CHCFG */
 #define SPI_CH_HS_EN		(1 << 6)
 #define SPI_CH_RST		(1 << 5)
diff --git a/board/samsung/smdk5250/spl_boot.c b/board/samsung/smdk5250/spl_boot.c
index d8f3c1e..9e99512 100644
--- a/board/samsung/smdk5250/spl_boot.c
+++ b/board/samsung/smdk5250/spl_boot.c
@@ -22,16 +22,119 @@ 
 
 #include<common.h>
 #include<config.h>
+#include <spi.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/spi.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/periph.h>
+#include <asm/arch/spl.h>
 
-enum boot_mode {
-	BOOT_MODE_MMC = 4,
-	BOOT_MODE_SERIAL = 20,
-	/* Boot based on Operating Mode pin settings */
-	BOOT_MODE_OM = 32,
-	BOOT_MODE_USB,	/* Boot using USB download */
-};
+static void spi_rx_tx(struct exynos_spi *regs, int todo,
+			void *dinp, void const *doutp, int i)
+{
+	uint *rxp = (uint *)(dinp + (i * (32 * 1024)));
+	int rx_lvl, tx_lvl;
+	uint out_bytes, in_bytes;
+
+	out_bytes = in_bytes = todo;
+	setbits_le32(&regs->ch_cfg, SPI_CH_RST);
+	clrbits_le32(&regs->ch_cfg, SPI_CH_RST);
+	writel(((todo * 8) / 32) | SPI_PACKET_CNT_EN, &regs->pkt_cnt);
+
+	while (in_bytes) {
+		uint32_t spi_sts;
+		int temp;
+
+		spi_sts = readl(&regs->spi_sts);
+		rx_lvl = ((spi_sts >> 15) & 0x7f);
+		tx_lvl = ((spi_sts >> 6) & 0x7f);
+		while (tx_lvl < 32 && out_bytes) {
+			temp = 0xffffffff;
+			writel(temp, &regs->tx_data);
+			out_bytes -= 4;
+			tx_lvl += 4;
+		}
+		while (rx_lvl >= 4 && in_bytes) {
+			temp = readl(&regs->rx_data);
+			if (rxp)
+				*rxp++ = temp;
+			in_bytes -= 4;
+			rx_lvl -= 4;
+		}
+	}
+}
+
+/**
+ * Copy uboot from spi flash to RAM
+ *
+ * @parma uboot_size	size of u-boot to copy
+ * @param uboot_addr	address of u-boot to copy
+ */
+static void exynos_spi_copy(unsigned int uboot_size, unsigned int uboot_addr)
+{
+	int upto, todo;
+	int i;
+	struct exynos_spi *regs = (struct exynos_spi *)CONFIG_ENV_SPI_BASE;
+
+	set_spi_clk(PERIPH_ID_SPI1, 50000000); /* set spi clock to 50Mhz */
+	/* set the spi1 GPIO */
+	exynos_pinmux_config(PERIPH_ID_SPI1, PINMUX_FLAG_NONE);
+
+	/* set pktcnt and enable it */
+	writel(4 | SPI_PACKET_CNT_EN, &regs->pkt_cnt);
+	/* set FB_CLK_SEL */
+	writel(SPI_FB_DELAY_180, &regs->fb_clk);
+	/* set CH_WIDTH and BUS_WIDTH as word */
+	setbits_le32(&regs->mode_cfg, SPI_MODE_CH_WIDTH_WORD |
+					SPI_MODE_BUS_WIDTH_WORD);
+	clrbits_le32(&regs->ch_cfg, SPI_CH_CPOL_L); /* CPOL: active high */
+
+	/* clear rx and tx channel if set priveously */
+	clrbits_le32(&regs->ch_cfg, SPI_RX_CH_ON | SPI_TX_CH_ON);
 
-	typedef u32 (*spi_copy_func_t)(u32 offset, u32 nblock, u32 dst);
+	setbits_le32(&regs->swap_cfg, SPI_RX_SWAP_EN |
+		SPI_RX_BYTE_SWAP |
+		SPI_RX_HWORD_SWAP);
+
+	/* do a soft reset */
+	setbits_le32(&regs->ch_cfg, SPI_CH_RST);
+	clrbits_le32(&regs->ch_cfg, SPI_CH_RST);
+
+	/* now set rx and tx channel ON */
+	setbits_le32(&regs->ch_cfg, SPI_RX_CH_ON | SPI_TX_CH_ON | SPI_CH_HS_EN);
+	clrbits_le32(&regs->cs_reg, SPI_SLAVE_SIG_INACT); /* CS low */
+
+	/* Send read instruction (0x3h) followed by a 24 bit addr */
+	writel((SF_READ_DATA_CMD << 24) | SPI_FLASH_UBOOT_POS, &regs->tx_data);
+
+	/* waiting for TX done */
+	while (!(readl(&regs->spi_sts) & SPI_ST_TX_DONE))
+		;
+
+	for (upto = 0, i = 0; upto < uboot_size; upto += todo, i++) {
+		todo = min(uboot_size - upto, (1 << 15));
+		spi_rx_tx(regs, todo, (void *)(uboot_addr),
+					(void *)(SPI_FLASH_UBOOT_POS), i);
+	}
+
+	setbits_le32(&regs->cs_reg, SPI_SLAVE_SIG_INACT);/* make the CS high */
+
+	/*
+	 * Let put controller mode to BYTE as
+	 * SPI driver does not support WORD mode yet
+	 */
+	clrbits_le32(&regs->mode_cfg, SPI_MODE_CH_WIDTH_WORD |
+					SPI_MODE_BUS_WIDTH_WORD);
+	writel(0, &regs->swap_cfg);
+
+	/*
+	 * Flush spi tx, rx fifos and reset the SPI controller
+	 * and clear rx/tx channel
+	 */
+	clrsetbits_le32(&regs->ch_cfg, SPI_CH_HS_EN, SPI_CH_RST);
+	clrbits_le32(&regs->ch_cfg, SPI_CH_RST);
+	clrbits_le32(&regs->ch_cfg, SPI_TX_CH_ON | SPI_RX_CH_ON);
+}
 
 /*
 * Copy U-boot from mmc to RAM:
@@ -40,17 +143,16 @@  enum boot_mode {
 */
 void copy_uboot_to_ram(void)
 {
-	spi_copy_func_t spi_copy;
 	enum boot_mode bootmode;
 	u32 (*copy_bl2)(u32, u32, u32);
+	struct spl_machine_param *param = spl_get_machine_params();
 
 	bootmode = readl(EXYNOS5_POWER_BASE) & OM_STAT;
 
 	switch (bootmode) {
 	case BOOT_MODE_SERIAL:
-		spi_copy = *(spi_copy_func_t *)EXYNOS_COPY_SPI_FNPTR_ADDR;
-		spi_copy(SPI_FLASH_UBOOT_POS, CONFIG_BL2_SIZE,
-						CONFIG_SYS_TEXT_BASE);
+		/* let us our own function to copy u-boot from SF */
+		exynos_spi_copy(param->uboot_size, CONFIG_SYS_TEXT_BASE);
 		break;
 	case BOOT_MODE_MMC:
 		copy_bl2 = (void *) *(u32 *)COPY_BL2_FNPTR_ADDR;
diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h
index 3d5b609..1910df8 100644
--- a/include/configs/exynos5250-dt.h
+++ b/include/configs/exynos5250-dt.h
@@ -135,6 +135,8 @@ 
 
 /* MMC SPL */
 #define CONFIG_SPL
+#define CONFIG_SPL_GPIO_SUPPORT
+
 #define COPY_BL2_FNPTR_ADDR	0x02020030
 
 /* specific .lds file */
@@ -288,6 +290,7 @@ 
 #define CONFIG_ENV_SPI_MODE	SPI_MODE_0
 #define CONFIG_ENV_SECT_SIZE	CONFIG_ENV_SIZE
 #define CONFIG_ENV_SPI_BUS	1
+#define CONFIG_ENV_SPI_BASE	0x12D30000
 #define CONFIG_ENV_SPI_MAX_HZ	50000000
 #endif
 
diff --git a/spl/Makefile b/spl/Makefile
index 101d478..0f5efc2 100644
--- a/spl/Makefile
+++ b/spl/Makefile
@@ -92,6 +92,10 @@  LIBS-y += arch/$(ARCH)/cpu/tegra-common/libcputegra-common.o
 LIBS-y += $(CPUDIR)/tegra-common/libtegra-common.o
 endif
 
+ifneq ($(CONFIG_EXYNOS4)$(CONFIG_EXYNOS5),)
+LIBS-y += $(CPUDIR)/s5p-common/libs5p-common.o
+endif
+
 # Add GCC lib
 ifeq ("$(USE_PRIVATE_LIBGCC)", "yes")
 PLATFORM_LIBGCC = $(SPLTREE)/arch/$(ARCH)/lib/libgcc.o