@@ -12,7 +12,7 @@ obj-$(CONFIG_REGULATOR_USERSPACE_CONSUMER) += userspace-consumer.o
obj-$(CONFIG_REGULATOR_88PM8607) += 88pm8607.o
obj-$(CONFIG_REGULATOR_AAT2870) += aat2870-regulator.o
obj-$(CONFIG_REGULATOR_AB3100) += ab3100.o
-obj-$(CONFIG_REGULATOR_AB8500) += ab8500.o
+obj-$(CONFIG_REGULATOR_AB8500) += ab8500.o ab8500-ext.o
obj-$(CONFIG_REGULATOR_AD5398) += ad5398.o
obj-$(CONFIG_REGULATOR_ANATOP) += anatop-regulator.o
obj-$(CONFIG_REGULATOR_ARIZONA) += arizona-micsupp.o arizona-ldo1.o
new file mode 100644
@@ -0,0 +1,394 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License Terms: GNU General Public License v2
+ *
+ * Authors: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
+ *
+ * This file is based on drivers/regulator/ab8500.c
+ *
+ * AB8500 external regulators
+ *
+ * ab8500-ext supports the following regulators:
+ * - VextSupply3
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/mfd/abx500.h>
+#include <linux/mfd/abx500/ab8500.h>
+#include <linux/regulator/ab8500.h>
+
+/**
+ * struct ab8500_ext_regulator_info - ab8500 regulator information
+ * @dev: device pointer
+ * @desc: regulator description
+ * @rdev: regulator device
+ * @is_enabled: status of regulator (on/off)
+ * @update_bank: bank to control on/off
+ * @update_reg: register to control on/off
+ * @update_mask: mask to enable/disable and set mode of regulator
+ * @update_val: bits holding the regulator current mode
+ * @update_val_en: bits to set EN pin active (LPn pin deactive)
+ * normally this means high power mode
+ * @update_val_en_lp: bits to set EN pin active and LPn pin active
+ * normally this means low power mode
+ * @delay: startup delay in ms
+ */
+struct ab8500_ext_regulator_info {
+ struct device *dev;
+ struct regulator_desc desc;
+ struct regulator_dev *rdev;
+ bool is_enabled;
+ u8 update_bank;
+ u8 update_reg;
+ u8 update_mask;
+ u8 update_val;
+ u8 update_val_en;
+ u8 update_val_en_lp;
+};
+
+static int ab8500_ext_regulator_enable(struct regulator_dev *rdev)
+{
+ int ret;
+ struct ab8500_ext_regulator_info *info = rdev_get_drvdata(rdev);
+
+ if (info == NULL) {
+ dev_err(rdev_get_dev(rdev), "regulator info null pointer\n");
+ return -EINVAL;
+ }
+
+ ret = abx500_mask_and_set_register_interruptible(info->dev,
+ info->update_bank, info->update_reg,
+ info->update_mask, info->update_val);
+ if (ret < 0)
+ dev_err(rdev_get_dev(info->rdev),
+ "couldn't set enable bits for regulator\n");
+
+ info->is_enabled = true;
+
+ dev_dbg(rdev_get_dev(rdev), "%s-enable (bank, reg, mask, value):"
+ " 0x%02x, 0x%02x, 0x%02x, 0x%02x\n",
+ info->desc.name, info->update_bank, info->update_reg,
+ info->update_mask, info->update_val);
+
+ return ret;
+}
+
+static int ab8500_ext_regulator_disable(struct regulator_dev *rdev)
+{
+ int ret;
+ struct ab8500_ext_regulator_info *info = rdev_get_drvdata(rdev);
+
+ if (info == NULL) {
+ dev_err(rdev_get_dev(rdev), "regulator info null pointer\n");
+ return -EINVAL;
+ }
+
+ ret = abx500_mask_and_set_register_interruptible(info->dev,
+ info->update_bank, info->update_reg,
+ info->update_mask, 0x0);
+ if (ret < 0)
+ dev_err(rdev_get_dev(info->rdev),
+ "couldn't set disable bits for regulator\n");
+
+ info->is_enabled = false;
+
+ dev_dbg(rdev_get_dev(rdev), "%s-disable (bank, reg, mask, value):"
+ " 0x%02x, 0x%02x, 0x%02x, 0x%02x\n",
+ info->desc.name, info->update_bank, info->update_reg,
+ info->update_mask, 0x0);
+
+ return ret;
+}
+
+static int ab8500_ext_regulator_is_enabled(struct regulator_dev *rdev)
+{
+ int ret;
+ struct ab8500_ext_regulator_info *info = rdev_get_drvdata(rdev);
+ u8 regval;
+
+ if (info == NULL) {
+ dev_err(rdev_get_dev(rdev), "regulator info null pointer\n");
+ return -EINVAL;
+ }
+
+ ret = abx500_get_register_interruptible(info->dev,
+ info->update_bank, info->update_reg, ®val);
+ if (ret < 0) {
+ dev_err(rdev_get_dev(rdev),
+ "couldn't read 0x%x register\n", info->update_reg);
+ return ret;
+ }
+
+ dev_dbg(rdev_get_dev(rdev), "%s-is_enabled (bank, reg, mask, value):"
+ " 0x%02x, 0x%02x, 0x%02x, 0x%02x\n",
+ info->desc.name, info->update_bank, info->update_reg,
+ info->update_mask, regval);
+
+ if (regval & info->update_mask)
+ info->is_enabled = true;
+ else
+ info->is_enabled = false;
+
+ return info->is_enabled;
+}
+
+static int ab8500_ext_regulator_set_mode(struct regulator_dev *rdev,
+ unsigned int mode)
+{
+ int ret = 0;
+ struct ab8500_ext_regulator_info *info = rdev_get_drvdata(rdev);
+
+ if (info == NULL) {
+ dev_err(rdev_get_dev(rdev), "regulator info null pointer\n");
+ return -EINVAL;
+ }
+
+ switch (mode) {
+ case REGULATOR_MODE_NORMAL:
+ info->update_val = info->update_val_hp;
+ break;
+ case REGULATOR_MODE_IDLE:
+ info->update_val = info->update_val_lp;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ if (info->is_enabled) {
+ u8 regval;
+
+ ret = enable(info, ®val);
+ if (ret < 0)
+ dev_err(rdev_get_dev(rdev),
+ "Could not set regulator mode.\n");
+
+ dev_dbg(rdev_get_dev(rdev),
+ "%s-set_mode (bank, reg, mask, value): "
+ "0x%x, 0x%x, 0x%x, 0x%x\n",
+ info->desc.name, info->update_bank, info->update_reg,
+ info->update_mask, regval);
+ }
+
+ return ret;
+}
+
+static unsigned int ab8500_ext_regulator_get_mode(struct regulator_dev *rdev)
+{
+ struct ab8500_ext_regulator_info *info = rdev_get_drvdata(rdev);
+ int ret;
+
+ if (info == NULL) {
+ dev_err(rdev_get_dev(rdev), "regulator info null pointer\n");
+ return -EINVAL;
+ }
+
+ if (info->update_val == info->update_val_hp)
+ ret = REGULATOR_MODE_NORMAL;
+ else if (info->update_val == info->update_val_lp)
+ ret = REGULATOR_MODE_IDLE;
+ else
+ ret = -EINVAL;
+
+ return ret;
+}
+
+static int ab8500_ext_fixed_get_voltage(struct regulator_dev *rdev)
+{
+ struct regulation_constraints *regu_constraints = rdev->constraints;
+
+ if (regu_constraints == NULL) {
+ dev_err(rdev_get_dev(rdev), "regulator constraints null pointer\n");
+ return -EINVAL;
+ }
+ if (regu_constraints->min_uV && regu_constraints->max_uV) {
+ if (regu_constraints->min_uV == regu_constraints->max_uV)
+ return regu_constraints->min_uV;
+ }
+ return -EINVAL;
+}
+
+static int ab8500_ext_list_voltage(struct regulator_dev *rdev,
+ unsigned selector)
+{
+ struct regulation_constraints *regu_constraints = rdev->constraints;
+
+ if (regu_constraints == NULL) {
+ dev_err(rdev_get_dev(rdev), "regulator constraints null pointer\n");
+ return -EINVAL;
+ }
+ /* return the uV for the fixed regulators */
+ if (regu_constraints->min_uV && regu_constraints->max_uV) {
+ if (regu_constraints->min_uV == regu_constraints->max_uV)
+ return regu_constraints->min_uV;
+ }
+ return -EINVAL;
+}
+
+static struct regulator_ops ab8500_ext_regulator_ops = {
+ .enable = ab8500_ext_regulator_enable,
+ .disable = ab8500_ext_regulator_disable,
+ .is_enabled = ab8500_ext_regulator_is_enabled,
+ .set_mode = ab8500_ext_regulator_set_mode,
+ .get_mode = ab8500_ext_regulator_get_mode,
+ .get_voltage = ab8500_ext_fixed_get_voltage,
+ .list_voltage = ab8500_ext_list_voltage,
+};
+
+
+static struct ab8500_ext_regulator_info
+ ab8500_ext_regulator_info[AB8500_NUM_EXT_REGULATORS] = {
+ [AB8500_EXT_SUPPLY1] = {
+ .desc = {
+ .name = "VEXTSUPPLY1",
+ .ops = &ab8500_ext_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .id = AB8500_EXT_SUPPLY1,
+ .owner = THIS_MODULE,
+ .n_voltages = 1,
+ },
+ .update_bank = 0x04,
+ .update_reg = 0x08,
+ .update_mask = 0x03,
+ .update_val = 0x01,
+ .update_val_hp = 0x01,
+ .update_val_lp = 0x03,
+ .update_val_hw = 0x02,
+ },
+ [AB8500_EXT_SUPPLY2] = {
+ .desc = {
+ .name = "VEXTSUPPLY2",
+ .ops = &ab8500_ext_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .id = AB8500_EXT_SUPPLY2,
+ .owner = THIS_MODULE,
+ .n_voltages = 1,
+ },
+ .update_bank = 0x04,
+ .update_reg = 0x08,
+ .update_mask = 0x0c,
+ .update_val = 0x04,
+ .update_val_hp = 0x04,
+ .update_val_lp = 0x0c,
+ .update_val_hw = 0x08,
+ },
+ [AB8500_EXT_SUPPLY3] = {
+ .desc = {
+ .name = "VEXTSUPPLY3",
+ .ops = &ab8500_ext_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .id = AB8500_EXT_SUPPLY3,
+ .owner = THIS_MODULE,
+ .n_voltages = 1,
+ },
+ .update_bank = 0x04,
+ .update_reg = 0x08,
+ .update_mask = 0x30,
+ .update_val = 0x10,
+ .update_val_en = 0x10,
+ .update_val_en_lp = 0x30,
+ },
+};
+
+int ab8500_ext_regulator_init(struct platform_device *pdev)
+{
+ struct ab8500 *ab8500 = dev_get_drvdata(pdev->dev.parent);
+ struct ab8500_platform_data *ppdata;
+ struct ab8500_regulator_platform_data *pdata;
+ struct regulator_config config = { };
+ int i, err;
+
+ if (!ab8500) {
+ dev_err(&pdev->dev, "null mfd parent\n");
+ return -EINVAL;
+ }
+ ppdata = dev_get_platdata(ab8500->dev);
+ if (!ppdata) {
+ dev_err(&pdev->dev, "null parent pdata\n");
+ return -EINVAL;
+ }
+
+ pdata = ppdata->regulator;
+ if (!pdata) {
+ dev_err(&pdev->dev, "null pdata\n");
+ return -EINVAL;
+ }
+
+ /* make sure the platform data has the correct size */
+ if (pdata->num_ext_regulator != ARRAY_SIZE(ab8500_ext_regulator_info)) {
+ dev_err(&pdev->dev, "Configuration error: size mismatch.\n");
+ return -EINVAL;
+ }
+
+ /* check for AB8500 2.x */
+ if (abx500_get_chip_id(&pdev->dev) < 0x30) {
+ struct ab8500_ext_regulator_info *info;
+
+ /* VextSupply3LPn is inverted on AB8500 2.x */
+ info = &ab8500_ext_regulator_info[AB8500_EXT_SUPPLY3];
+ info->update_val = 0x30;
+ info->update_val_en = 0x30;
+ info->update_val_en_lp = 0x10;
+ }
+
+ /* register all regulators */
+ for (i = 0; i < ARRAY_SIZE(ab8500_ext_regulator_info); i++) {
+ struct ab8500_ext_regulator_info *info = NULL;
+
+ /* assign per-regulator data */
+ info = &ab8500_ext_regulator_info[i];
+ info->dev = &pdev->dev;
+
+ config.dev = &pdev->dev;
+ config.init_data = &pdata->ext_regulator[i];
+ config.driver_data = info;
+
+ /* register regulator with framework */
+ info->rdev = regulator_register(&info->desc, &config);
+
+ if (IS_ERR(info->rdev)) {
+ err = PTR_ERR(info->rdev);
+ dev_err(&pdev->dev, "failed to register regulator %s\n",
+ info->desc.name);
+ /* when we fail, un-register all earlier regulators */
+ while (--i >= 0) {
+ info = &ab8500_ext_regulator_info[i];
+ regulator_unregister(info->rdev);
+ }
+ return err;
+ }
+
+ dev_dbg(rdev_get_dev(info->rdev),
+ "%s-probed\n", info->desc.name);
+ }
+
+ return 0;
+}
+
+int ab8500_ext_regulator_exit(struct platform_device *pdev)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(ab8500_ext_regulator_info); i++) {
+ struct ab8500_ext_regulator_info *info = NULL;
+ info = &ab8500_ext_regulator_info[i];
+
+ dev_vdbg(rdev_get_dev(info->rdev),
+ "%s-remove\n", info->desc.name);
+
+ regulator_unregister(info->rdev);
+ }
+
+ return 0;
+}
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Bengt Jonsson <bengt.g.jonsson@stericsson.com>");
+MODULE_DESCRIPTION("AB8500 external regulator driver");
+MODULE_ALIAS("platform:ab8500-ext-regulator");
@@ -947,6 +947,11 @@ static int ab8500_regulator_probe(struct platform_device *pdev)
return err;
}
+ /* register external regulators (before Vaux1, 2 and 3) */
+ err = ab8500_ext_regulator_init(pdev);
+ if (err)
+ return err;
+
/* register all regulators */
for (i = 0; i < ARRAY_SIZE(ab8500_regulator_info); i++) {
err = ab8500_regulator_register(pdev, &pdata->regulator[i], i, NULL);
@@ -959,7 +964,7 @@ static int ab8500_regulator_probe(struct platform_device *pdev)
static int ab8500_regulator_remove(struct platform_device *pdev)
{
- int i;
+ int i, err;
for (i = 0; i < ARRAY_SIZE(ab8500_regulator_info); i++) {
struct ab8500_regulator_info *info = NULL;
@@ -971,6 +976,11 @@ static int ab8500_regulator_remove(struct platform_device *pdev)
regulator_unregister(info->regulator);
}
+ /* remove external regulators (after Vaux1, 2 and 3) */
+ err = ab8500_ext_regulator_exit(pdev);
+ if (err)
+ return err;
+
return 0;
}
@@ -10,6 +10,8 @@
#ifndef __LINUX_MFD_AB8500_REGULATOR_H
#define __LINUX_MFD_AB8500_REGULATOR_H
+#include <linux/platform_device.h>
+
/* AB8500 regulators */
enum ab8500_regulator_id {
AB8500_LDO_AUX1,
@@ -140,11 +142,37 @@ enum ab9540_regulator_reg {
AB9540_NUM_REGULATOR_REGISTERS,
};
+/* AB8500 external regulators */
+enum ab8500_ext_regulator_id {
+ AB8500_EXT_SUPPLY1,
+ AB8500_EXT_SUPPLY2,
+ AB8500_EXT_SUPPLY3,
+ AB8500_NUM_EXT_REGULATORS,
+};
+
+/* AB8500 regulator platform data */
struct ab8500_regulator_platform_data {
int num_reg_init;
struct ab8500_regulator_reg_init *reg_init;
int num_regulator;
struct regulator_init_data *regulator;
+ int num_ext_regulator;
+ struct regulator_init_data *ext_regulator;
};
+/* AB8500 external regulator functions (internal) */
+#ifdef CONFIG_REGULATOR_AB8500_EXT
+int ab8500_ext_regulator_init(struct platform_device *pdev);
+int ab8500_ext_regulator_exit(struct platform_device *pdev);
+#else
+inline int ab8500_ext_regulator_init(struct platform_device *pdev)
+{
+ return 0;
+}
+inline int ab8500_ext_regulator_exit(struct platform_device *pdev)
+{
+ return 0;
+}
+#endif
+
#endif
The ABx500 is capable of controlling three external regulator supplies. Most commonly on and off are supported, but if an external regulator chipset or power supply supports high-power and low-power mode settings, we can control those too. Signed-off-by: Lee Jones <lee.jones@linaro.org> --- drivers/regulator/Makefile | 2 +- drivers/regulator/ab8500-ext.c | 394 ++++++++++++++++++++++++++++++++++++++ drivers/regulator/ab8500.c | 12 +- include/linux/regulator/ab8500.h | 28 +++ 4 files changed, 434 insertions(+), 2 deletions(-) create mode 100644 drivers/regulator/ab8500-ext.c