@@ -259,13 +259,13 @@ static struct ab8500_regulator_reg_init ab8500_reg_init[] = {
*/
INIT_REGULATOR_REGISTER(AB8500_VREFDDR, 0x03, 0x00),
/*
- * VextSupply1Regu = HW control
- * VextSupply2Regu = HW control
- * VextSupply3Regu = HW control
+ * VextSupply1Regu = force LP
+ * VextSupply2Regu = force OFF
+ * VextSupply3Regu = force HP (-> STBB2=LP and TPS=LP)
* ExtSupply2Bypass = ExtSupply12LPn ball is 0 when Ena is 0
* ExtSupply3Bypass = ExtSupply3LPn ball is 0 when Ena is 0
*/
- INIT_REGULATOR_REGISTER(AB8500_EXTSUPPLYREGU, 0xff, 0x1a),
+ INIT_REGULATOR_REGISTER(AB8500_EXTSUPPLYREGU, 0xff, 0x13),
/*
* Vaux1Regu = force HP
* Vaux2Regu = force off
@@ -419,9 +419,60 @@ static struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = {
},
};
+/* supply for VextSupply3 */
+static struct regulator_consumer_supply ab8500_ext_supply3_consumers[] = {
+ /* SIM supply for 3 V SIM cards */
+ REGULATOR_SUPPLY("vinvsim", "sim-detect.0"),
+};
+
+/* extended configuration for VextSupply2, only used for HREFP_V20 boards */
+static struct ab8500_ext_regulator_cfg ab8500_ext_supply2 = {
+ .hwreq = true,
+};
+
+/*
+ * AB8500 external regulators
+ */
+static struct regulator_init_data ab8500_ext_regulators[] = {
+ /* fixed Vbat supplies VSMPS1_EXT_1V8 */
+ [AB8500_EXT_SUPPLY1] = {
+ .constraints = {
+ .name = "ab8500-ext-supply1",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .initial_mode = REGULATOR_MODE_IDLE,
+ .boot_on = 1,
+ .always_on = 1,
+ },
+ },
+ /* fixed Vbat supplies VSMPS2_EXT_1V36 and VSMPS5_EXT_1V15 */
+ [AB8500_EXT_SUPPLY2] = {
+ .constraints = {
+ .name = "ab8500-ext-supply2",
+ .min_uV = 1360000,
+ .max_uV = 1360000,
+ },
+ },
+ /* fixed Vbat supplies VSMPS3_EXT_3V4 and VSMPS4_EXT_3V4 */
+ [AB8500_EXT_SUPPLY3] = {
+ .constraints = {
+ .name = "ab8500-ext-supply3",
+ .min_uV = 3400000,
+ .max_uV = 3400000,
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ .boot_on = 1,
+ },
+ .num_consumer_supplies =
+ ARRAY_SIZE(ab8500_ext_supply3_consumers),
+ .consumer_supplies = ab8500_ext_supply3_consumers,
+ },
+};
+
struct ab8500_regulator_platform_data ab8500_regulator_plat_data = {
.reg_init = ab8500_reg_init,
.num_reg_init = ARRAY_SIZE(ab8500_reg_init),
.regulator = ab8500_regulators,
.num_regulator = ARRAY_SIZE(ab8500_regulators),
+ .ext_regulator = ab8500_ext_regulators,
+ .num_ext_regulator = ARRAY_SIZE(ab8500_ext_regulators),
};
Pass constraint information for recently supported external AB8500 controlled regulators. Also change the start-up initialisation settings for each of the 3 supported external supplies to low-power, off and high-power for supply 1, 2 and 3 respectively. Signed-off-by: Lee Jones <lee.jones@linaro.org> --- arch/arm/mach-ux500/board-mop500-regulators.c | 59 +++++++++++++++++++++++-- 1 file changed, 55 insertions(+), 4 deletions(-)