@@ -42,32 +42,6 @@ static struct resource dma40_resources[] = {
}
};
-/* Default configuration for physcial memcpy */
-struct stedma40_chan_cfg dma40_memcpy_conf_phy = {
- .mode = STEDMA40_MODE_PHYSICAL,
- .dir = STEDMA40_MEM_TO_MEM,
-
- .src_info.data_width = STEDMA40_BYTE_WIDTH,
- .src_info.psize = STEDMA40_PSIZE_PHY_1,
- .src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
-
- .dst_info.data_width = STEDMA40_BYTE_WIDTH,
- .dst_info.psize = STEDMA40_PSIZE_PHY_1,
- .dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
-};
-/* Default configuration for logical memcpy */
-struct stedma40_chan_cfg dma40_memcpy_conf_log = {
- .dir = STEDMA40_MEM_TO_MEM,
-
- .src_info.data_width = STEDMA40_BYTE_WIDTH,
- .src_info.psize = STEDMA40_PSIZE_LOG_1,
- .src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
-
- .dst_info.data_width = STEDMA40_BYTE_WIDTH,
- .dst_info.psize = STEDMA40_PSIZE_LOG_1,
- .dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
-};
-
/*
* Mapping between destination event lines and physical device address.
* The event line is tied to a device and therefore the address is constant.
@@ -150,8 +124,6 @@ static struct stedma40_platform_data dma40_plat_data = {
.dev_len = DB8500_DMA_NR_DEV,
.dev_rx = dma40_rx_map,
.dev_tx = dma40_tx_map,
- .memcpy_conf_phy = &dma40_memcpy_conf_phy,
- .memcpy_conf_log = &dma40_memcpy_conf_log,
.disabled_channels = {-1},
};
@@ -66,6 +66,34 @@ static int dma40_memcpy_channels[] = {
DB8500_DMA_MEMCPY_TX_5,
};
+/* Default configuration for physcial memcpy */
+struct stedma40_chan_cfg dma40_memcpy_conf_phy = {
+ .mode = STEDMA40_MODE_PHYSICAL,
+ .dir = STEDMA40_MEM_TO_MEM,
+
+ .src_info.data_width = STEDMA40_BYTE_WIDTH,
+ .src_info.psize = STEDMA40_PSIZE_PHY_1,
+ .src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
+
+ .dst_info.data_width = STEDMA40_BYTE_WIDTH,
+ .dst_info.psize = STEDMA40_PSIZE_PHY_1,
+ .dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
+};
+
+/* Default configuration for logical memcpy */
+struct stedma40_chan_cfg dma40_memcpy_conf_log = {
+ .mode = STEDMA40_MODE_LOGICAL,
+ .dir = STEDMA40_MEM_TO_MEM,
+
+ .src_info.data_width = STEDMA40_BYTE_WIDTH,
+ .src_info.psize = STEDMA40_PSIZE_LOG_1,
+ .src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
+
+ .dst_info.data_width = STEDMA40_BYTE_WIDTH,
+ .dst_info.psize = STEDMA40_PSIZE_LOG_1,
+ .dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
+};
+
/**
* enum 40_command - The different commands and/or statuses.
*
@@ -2023,13 +2051,13 @@ static int d40_config_memcpy(struct d40_chan *d40c)
dma_cap_mask_t cap = d40c->chan.device->cap_mask;
if (dma_has_cap(DMA_MEMCPY, cap) && !dma_has_cap(DMA_SLAVE, cap)) {
- d40c->dma_cfg = *d40c->base->plat_data->memcpy_conf_log;
+ d40c->dma_cfg = dma40_memcpy_conf_log;
d40c->dma_cfg.src_dev_type = STEDMA40_DEV_SRC_MEMORY;
d40c->dma_cfg.dst_dev_type = dma40_memcpy_channels[d40c->chan.chan_id];
} else if (dma_has_cap(DMA_MEMCPY, cap) &&
dma_has_cap(DMA_SLAVE, cap)) {
- d40c->dma_cfg = *d40c->base->plat_data->memcpy_conf_phy;
+ d40c->dma_cfg = dma40_memcpy_conf_phy;
} else {
chan_err(d40c, "No memcpy\n");
return -EINVAL;
@@ -141,8 +141,6 @@ struct stedma40_chan_cfg {
* @dev_len: length of dev_tx and dev_rx
* @dev_tx: mapping between destination event line and io address
* @dev_rx: mapping between source event line and io address
- * @memcpy_conf_phy: default configuration of physical channel memcpy
- * @memcpy_conf_log: default configuration of logical channel memcpy
* @disabled_channels: A vector, ending with -1, that marks physical channels
* that are for different reasons not available for the driver.
* @soft_lli_chans: A vector, that marks physical channels will use LLI by SW
@@ -160,8 +158,6 @@ struct stedma40_platform_data {
u32 dev_len;
const dma_addr_t *dev_tx;
const dma_addr_t *dev_rx;
- struct stedma40_chan_cfg *memcpy_conf_phy;
- struct stedma40_chan_cfg *memcpy_conf_log;
int disabled_channels[STEDMA40_MAX_PHYS];
int *soft_lli_chans;
int num_of_soft_lli_chans;
There are only two default memcpy configurations used for the DMA40 driver; one for physical memcpy and one for logical memcpy. Instead of invariably passing the same configurations though platform data, we're moving them into the driver instead. Cc: Vinod Koul <vinod.koul@intel.com> Cc: Dan Williams <djbw@fb.com> Cc: Per Forlin <per.forlin@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> --- arch/arm/mach-ux500/devices-db8500.c | 28 ----------------------- drivers/dma/ste_dma40.c | 32 +++++++++++++++++++++++++-- include/linux/platform_data/dma-ste-dma40.h | 4 ---- 3 files changed, 30 insertions(+), 34 deletions(-)