diff mbox series

[v2,5/5] ARM: dts: imx7s-warp: add ov2680 sensor node

Message ID 20190326110227.7324-6-rui.silva@linaro.org
State Superseded
Headers show
Series ARM: imx7s: add media nodes | expand

Commit Message

Rui Miguel Silva March 26, 2019, 11:02 a.m. UTC 
Warp7 comes with a Omnivision OV2680 sensor, add the node here to make
complete the camera data path for this system. Add the needed regulator
to the analog voltage supply, the port and endpoints in mipi_csi node
and the pinctrl for the reset gpio.

Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>

---
 arch/arm/boot/dts/imx7s-warp.dts | 45 ++++++++++++++++++++++++++++++++
 1 file changed, 45 insertions(+)

-- 
2.21.0
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/imx7s-warp.dts b/arch/arm/boot/dts/imx7s-warp.dts
index 0063fabfcd30..3bcae72d33e2 100644
--- a/arch/arm/boot/dts/imx7s-warp.dts
+++ b/arch/arm/boot/dts/imx7s-warp.dts
@@ -55,6 +55,14 @@ 
 		regulator-always-on;
 	};
 
+	reg_peri_3p15v: regulator-peri-3p15v {
+		compatible = "regulator-fixed";
+		regulator-name = "peri_3p15v_reg";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+		regulator-always-on;
+	};
+
 	sound {
 		compatible = "simple-audio-card";
 		simple-audio-card,name = "imx7-sgtl5000";
@@ -184,6 +192,27 @@ 
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
+
+	ov2680: camera@36 {
+		compatible = "ovti,ov2680";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov2680>;
+		reg = <0x36>;
+		clocks = <&osc>;
+		clock-names = "xvclk";
+		reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+		DOVDD-supply = <&sw2_reg>;
+		DVDD-supply = <&sw2_reg>;
+		AVDD-supply = <&reg_peri_3p15v>;
+
+		port {
+			ov2680_to_mipi: endpoint {
+				remote-endpoint = <&mipi_from_sensor>;
+				clock-lanes = <0>;
+				data-lanes = <1>;
+			};
+		};
+	};
 };
 
 &i2c3 {
@@ -221,6 +250,16 @@ 
 	clock-frequency = <166000000>;
 	fsl,csis-hs-settle = <3>;
 	status = "okay";
+
+	port@0 {
+		reg = <0>;
+
+		mipi_from_sensor: endpoint {
+			remote-endpoint = <&ov2680_to_mipi>;
+			data-lanes = <1>;
+		};
+
+	};
 };
 
 &sai1 {
@@ -343,6 +382,12 @@ 
 		>;
 	};
 
+	pinctrl_ov2680: ov2660grp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO03__GPIO1_IO3	0x14
+		>;
+	};
+
 	pinctrl_sai1: sai1grp {
 		fsl,pins = <
 			MX7D_PAD_SAI1_RX_DATA__SAI1_RX_DATA0	0x1f