new file mode 100644
@@ -0,0 +1,190 @@
+Qualcomm SM8150 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+QCS404 platform.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be "qcom,sm8150-pinctrl"
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the base address and size of the north, south, west
+ and east TLMM tiles.
+
+- reg-names:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Defintiion: names for the cells of reg, must contain "north", "south"
+ "west" and "east".
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+ Usage: required
+ Value type: <none>
+ Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 2. Specifying the pin number and flags, as defined
+ in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+ Usage: required
+ Value type: <none>
+ Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 2. Specifying the pin number and flags, as defined
+ in <dt-bindings/gpio/gpio.h>
+
+- gpio-ranges:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: see ../gpio/gpio.txt
+
+- gpio-reserved-ranges:
+ Usage: optional
+ Value type: <prop-encoded-array>
+ Definition: see ../gpio/gpio.txt
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+ Usage: required
+ Value type: <string-array>
+ Definition: List of gpio pins affected by the properties specified in
+ this subnode.
+
+ Valid pins are:
+ gpio0-gpio149
+ Supports mux, bias and drive-strength
+
+ sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd,
+ sdc2_data sdc1_rclk
+ Supports bias and drive-strength
+
+ ufs_reset
+ Supports bias and drive-strength
+
+- function:
+ Usage: required
+ Value type: <string>
+ Definition: Specify the alternative function to be configured for the
+ specified pins. Functions are only valid for gpio pins.
+ Valid values are:
+
+ adsp_ext, agera_pll, aoss_cti, ddr_pxi2, atest_char,
+ atest_char0, atest_char1, atest_char2, atest_char3,
+ audio_ref, atest_usb1, atest_usb2, atest_usb10,
+ atest_usb11, atest_usb12, atest_usb13, atest_usb20,
+ atest_usb21, atest_usb22, atest_usb2, atest_usb23,
+ btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0,
+ cci_timer1, cci_timer2, cci_timer3, cci_timer4,
+ cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist,
+ ddr_pxi0, ddr_pxi1, ddr_pxi3, edp_hot, edp_lcd,
+ emac_phy, emac_pps, gcc_gp1, gcc_gp2, gcc_gp3, gpio,
+ hs1_mi2s, hs2_mi2s, hs3_mi2s, jitter_bist,
+ lpass_slimbus, mdp_vsync, mdp_vsync0, mdp_vsync1,
+ mdp_vsync2, mdp_vsync3, mss_lte, m_voc, nav_pps,
+ pa_indicator, pci_e0, phase_flag, pll_bypassnl,
+ pll_bist, pci_e1, pll_reset, pri_mi2s, pri_mi2s_ws,
+ prng_rosc, qdss, qdss_cti, qlink_request, qlink_enable,
+ qspi0, qspi1, qspi2, qspi3, qspi_clk, qspi_cs, qua_mi2s,
+ qup0, qup1, qup2, qup3, qup4, qup5, qup6, qup7, qup8,
+ qup9, qup10, qup11, qup12, qup13, qup14, qup15, qup16,
+ qup17, qup18, qup19, qup_l4, qup_l5, qup_l6, rgmii,
+ sdc4, sd_write, sec_mi2s, spkr_i2s, sp_cmu, ter_mi2s,
+ tgu_ch0, tgu_ch1, tgu_ch2, tgu_ch3, tsense_pwm1,
+ tsense_pwm2, tsif1, tsif2, uim1, uim2, uim_batt,
+ usb2phy_ac, usb_phy, vfr_1, vsense_trigger, wlan1_adc0,
+ wlan1_adc1, wlan2_adc0, wlan2_adc1, wmss_reset
+
+- bias-disable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as no pull.
+
+- bias-pull-down:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as pull down.
+
+- bias-pull-up:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as pull up.
+
+- output-high:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ high.
+ Not valid for sdc pins.
+
+- output-low:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ low.
+ Not valid for sdc pins.
+
+- drive-strength:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the drive strength for the specified pins, in mA.
+ Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+ tlmm: pinctrl@3000000 {
+ compatible = "qcom,sm8150-pinctrl";
+ reg = <0x03100000 0x300000>,
+ <0x03500000 0x300000>,
+ <0x03900000 0x300000>,
+ <0x03D00000 0x300000>;
+ reg-names = "west", "east", "north", "south";
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 175>;
+ gpio-reserved-ranges = <0 4>, <126 4>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };