diff mbox series

[v3,01/13] dt-bindings: display: Convert common panel bindings to DT schema

Message ID 20190705164221.4462-2-robh@kernel.org
State Accepted
Commit 821a1f7171aeea5e7818d30f70d7cf49b007357f
Headers show
Series [v3,01/13] dt-bindings: display: Convert common panel bindings to DT schema | expand

Commit Message

Rob Herring (Arm) July 5, 2019, 4:42 p.m. UTC
Convert the common panel bindings to DT schema consolidating scattered
definitions to a single schema file.

The 'simple-panel' binding just a collection of properties and not a
complete binding itself. All of the 'simple-panel' properties are
covered by the panel-common.txt binding with the exception of the
'no-hpd' property, so add that to the schema.

As there are lots of references to simple-panel.txt, just keep the file
with a reference to common.yaml for now until all the bindings are
converted.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/arm,versatile-tft-panel.txt |   2 +-
 .../bindings/display/panel/panel-common.txt   | 101 ------------
 .../bindings/display/panel/panel-common.yaml  | 149 ++++++++++++++++++
 .../bindings/display/panel/panel.txt          |   4 -
 .../bindings/display/panel/simple-panel.txt   |  29 +---
 5 files changed, 151 insertions(+), 134 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/panel.txt

Comments

Geert Uytterhoeven Oct. 25, 2019, 1:07 p.m. UTC | #1
Hi Rob,

On Fri, Jul 5, 2019 at 6:46 PM Rob Herring <robh@kernel.org> wrote:
> Convert the common panel bindings to DT schema consolidating scattered
> definitions to a single schema file.
>
> The 'simple-panel' binding just a collection of properties and not a
> complete binding itself. All of the 'simple-panel' properties are
> covered by the panel-common.txt binding with the exception of the
> 'no-hpd' property, so add that to the schema.
>
> As there are lots of references to simple-panel.txt, just keep the file
> with a reference to common.yaml for now until all the bindings are
> converted.
>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Acked-by: Sam Ravnborg <sam@ravnborg.org>
> Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
> Reviewed-by: Thierry Reding <treding@nvidia.com>
> Signed-off-by: Rob Herring <robh@kernel.org>

This is now commit 821a1f7171aeea5e ("dt-bindings: display: Convert
common panel bindings to DT schema").

> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/panel/panel-common.yaml

> +  backlight:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description:
> +      For panels whose backlight is controlled by an external backlight
> +      controller, this property contains a phandle that references the
> +      controller.

This paragraph seems to apply to all nodes named "backlight", causing
e.g. (for ARCH=arm mach_shmobile_defconfig) "make dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/panel/panel-common.yaml"
to start complaining:

    arch/arm/boot/dts/r8a7740-armadillo800eva.dt.yaml: backlight:
{'compatible': ['pwm-backlight'], 'pwms': [[40, 2, 33333, 1]],
'brightness-levels': [[0, 1, 2, 4, 8, 16, 32, 64, 128, 255]],
'default-brightness-level': [[9]], 'pinctrl-0': [[41]],
'pinctrl-names': ['default'], 'power-supply': [[42]], 'enable-gpios':
[[15, 61, 0]]} is not of type 'array'
    arch/arm/boot/dts/r8a7740-armadillo800eva.dt.yaml: backlight:
{'groups': ['tpu0_to2_1'], 'function': ['tpu0'], 'phandle': [[41]]} is
not of type 'array'

Do you know what's wrong?

Thanks!

Gr{oetje,eeting}s,

                        Geert
Rob Herring (Arm) Oct. 25, 2019, 2:25 p.m. UTC | #2
On Fri, Oct 25, 2019 at 8:07 AM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
>
> Hi Rob,
>
> On Fri, Jul 5, 2019 at 6:46 PM Rob Herring <robh@kernel.org> wrote:
> > Convert the common panel bindings to DT schema consolidating scattered
> > definitions to a single schema file.
> >
> > The 'simple-panel' binding just a collection of properties and not a
> > complete binding itself. All of the 'simple-panel' properties are
> > covered by the panel-common.txt binding with the exception of the
> > 'no-hpd' property, so add that to the schema.
> >
> > As there are lots of references to simple-panel.txt, just keep the file
> > with a reference to common.yaml for now until all the bindings are
> > converted.
> >
> > Cc: Thierry Reding <thierry.reding@gmail.com>
> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > Cc: dri-devel@lists.freedesktop.org
> > Acked-by: Sam Ravnborg <sam@ravnborg.org>
> > Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
> > Reviewed-by: Thierry Reding <treding@nvidia.com>
> > Signed-off-by: Rob Herring <robh@kernel.org>
>
> This is now commit 821a1f7171aeea5e ("dt-bindings: display: Convert
> common panel bindings to DT schema").
>
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/panel/panel-common.yaml
>
> > +  backlight:
> > +    $ref: /schemas/types.yaml#/definitions/phandle
> > +    description:
> > +      For panels whose backlight is controlled by an external backlight
> > +      controller, this property contains a phandle that references the
> > +      controller.
>
> This paragraph seems to apply to all nodes named "backlight", causing
> e.g. (for ARCH=arm mach_shmobile_defconfig) "make dtbs_check
> DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/panel/panel-common.yaml"
> to start complaining:
>
>     arch/arm/boot/dts/r8a7740-armadillo800eva.dt.yaml: backlight:
> {'compatible': ['pwm-backlight'], 'pwms': [[40, 2, 33333, 1]],
> 'brightness-levels': [[0, 1, 2, 4, 8, 16, 32, 64, 128, 255]],
> 'default-brightness-level': [[9]], 'pinctrl-0': [[41]],
> 'pinctrl-names': ['default'], 'power-supply': [[42]], 'enable-gpios':
> [[15, 61, 0]]} is not of type 'array'
>     arch/arm/boot/dts/r8a7740-armadillo800eva.dt.yaml: backlight:
> {'groups': ['tpu0_to2_1'], 'function': ['tpu0'], 'phandle': [[41]]} is
> not of type 'array'
>
> Do you know what's wrong?

I'm not seeing that. What does .../bindings/processed-schema.yaml look like?

Rob
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt b/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt
index 248141c3c7e3..0601a9e34703 100644
--- a/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt
+++ b/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt
@@ -10,7 +10,7 @@  Required properties:
 - compatible: should be "arm,versatile-tft-panel"
 
 Required subnodes:
-- port: see display/panel/panel-common.txt, graph.txt
+- port: see display/panel/panel-common.yaml, graph.txt
 
 
 Example:
diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.txt b/Documentation/devicetree/bindings/display/panel/panel-common.txt
deleted file mode 100644
index 5d2519af4bb5..000000000000
--- a/Documentation/devicetree/bindings/display/panel/panel-common.txt
+++ /dev/null
@@ -1,101 +0,0 @@ 
-Common Properties for Display Panel
-===================================
-
-This document defines device tree properties common to several classes of
-display panels. It doesn't constitue a device tree binding specification by
-itself but is meant to be referenced by device tree bindings.
-
-When referenced from panel device tree bindings the properties defined in this
-document are defined as follows. The panel device tree bindings are
-responsible for defining whether each property is required or optional.
-
-
-Descriptive Properties
-----------------------
-
-- width-mm,
-- height-mm: The width-mm and height-mm specify the width and height of the
-  physical area where images are displayed. These properties are expressed in
-  millimeters and rounded to the closest unit.
-
-- label: The label property specifies a symbolic name for the panel as a
-  string suitable for use by humans. It typically contains a name inscribed on
-  the system (e.g. as an affixed label) or specified in the system's
-  documentation (e.g. in the user's manual).
-
-  If no such name exists, and unless the property is mandatory according to
-  device tree bindings, it shall rather be omitted than constructed of
-  non-descriptive information. For instance an LCD panel in a system that
-  contains a single panel shall not be labelled "LCD" if that name is not
-  inscribed on the system or used in a descriptive fashion in system
-  documentation.
-
-
-Display Timings
----------------
-
-- panel-timing: Most display panels are restricted to a single resolution and
-  require specific display timings. The panel-timing subnode expresses those
-  timings as specified in the timing subnode section of the display timing
-  bindings defined in
-  Documentation/devicetree/bindings/display/panel/display-timing.txt.
-
-
-Connectivity
-------------
-
-- ports: Panels receive video data through one or multiple connections. While
-  the nature of those connections is specific to the panel type, the
-  connectivity is expressed in a standard fashion using ports as specified in
-  the device graph bindings defined in
-  Documentation/devicetree/bindings/graph.txt.
-
-- ddc-i2c-bus: Some panels expose EDID information through an I2C-compatible
-  bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a
-  phandle to the system I2C controller connected to that bus.
-
-
-Control I/Os
-------------
-
-Many display panels can be controlled through pins driven by GPIOs. The nature
-and timing of those control signals are device-specific and left for panel
-device tree bindings to specify. The following GPIO specifiers can however be
-used for panels that implement compatible control signals.
-
-- enable-gpios: Specifier for a GPIO connected to the panel enable control
-  signal. The enable signal is active high and enables operation of the panel.
-  This property can also be used for panels implementing an active low power
-  down signal, which is a negated version of the enable signal. Active low
-  enable signals (or active high power down signals) can be supported by
-  inverting the GPIO specifier polarity flag.
-
-  Note that the enable signal control panel operation only and must not be
-  confused with a backlight enable signal.
-
-- reset-gpios: Specifier for a GPIO coonnected to the panel reset control
-  signal. The reset signal is active low and resets the panel internal logic
-  while active. Active high reset signals can be supported by inverting the
-  GPIO specifier polarity flag.
-
-Power
------
-
-- power-supply: display panels require power to be supplied. While several
-  panels need more than one power supply with panel-specific constraints
-  governing the order and timings of the power supplies, in many cases a single
-  power supply is sufficient, either because the panel has a single power rail,
-  or because all its power rails can be driven by the same supply. In that case
-  the power-supply property specifies the supply powering the panel as a phandle
-  to a regulator.
-
-Backlight
----------
-
-Most display panels include a backlight. Some of them also include a backlight
-controller exposed through a control bus such as I2C or DSI. Others expose
-backlight control through GPIO, PWM or other signals connected to an external
-backlight controller.
-
-- backlight: For panels whose backlight is controlled by an external backlight
-  controller, this property contains a phandle that references the controller.
diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.yaml b/Documentation/devicetree/bindings/display/panel/panel-common.yaml
new file mode 100644
index 000000000000..ef8d8cdfcede
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/panel-common.yaml
@@ -0,0 +1,149 @@ 
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/panel-common.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Common Properties for Display Panels
+
+maintainers:
+  - Thierry Reding <thierry.reding@gmail.com>
+  - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+
+description: |
+  This document defines device tree properties common to several classes of
+  display panels. It doesn't constitue a device tree binding specification by
+  itself but is meant to be referenced by device tree bindings.
+
+  When referenced from panel device tree bindings the properties defined in this
+  document are defined as follows. The panel device tree bindings are
+  responsible for defining whether each property is required or optional.
+
+properties:
+  # Descriptive Properties
+  width-mm:
+    description:
+      Specifies the width of the physical area where images are displayed. This
+      property is expressed in millimeters and rounded to the closest unit.
+
+  height-mm:
+    description:
+      Specifies the height of the physical area where images are displayed. This
+      property is expressed in millimeters and rounded to the closest unit.
+
+  label:
+    description: |
+      The label property specifies a symbolic name for the panel as a
+      string suitable for use by humans. It typically contains a name inscribed
+      on the system (e.g. as an affixed label) or specified in the system's
+      documentation (e.g. in the user's manual).
+
+      If no such name exists, and unless the property is mandatory according to
+      device tree bindings, it shall rather be omitted than constructed of
+      non-descriptive information. For instance an LCD panel in a system that
+      contains a single panel shall not be labelled "LCD" if that name is not
+      inscribed on the system or used in a descriptive fashion in system
+      documentation.
+
+  rotation:
+    description:
+      Display rotation in degrees counter clockwise (0,90,180,270)
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 0, 90, 180, 270 ]
+
+  # Display Timings
+  panel-timing:
+    type: object
+    description:
+      Most display panels are restricted to a single resolution and
+      require specific display timings. The panel-timing subnode expresses those
+      timings as specified in the timing subnode section of the display timing
+      bindings defined in
+      Documentation/devicetree/bindings/display/panel/display-timing.txt.
+
+  # Connectivity
+  port:
+    type: object
+
+  ports:
+    type: object
+    description:
+      Panels receive video data through one or multiple connections. While
+      the nature of those connections is specific to the panel type, the
+      connectivity is expressed in a standard fashion using ports as specified
+      in the device graph bindings defined in
+      Documentation/devicetree/bindings/graph.txt.
+
+  ddc-i2c-bus:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Some panels expose EDID information through an I2C-compatible
+      bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a
+      phandle to the system I2C controller connected to that bus.
+
+  no-hpd:
+    type: boolean
+    description:
+      This panel is supposed to communicate that it's ready via HPD
+      (hot plug detect) signal, but the signal isn't hooked up so we should
+      hardcode the max delay from the panel spec when powering up the panel.
+
+  # Control I/Os
+
+  # Many display panels can be controlled through pins driven by GPIOs. The nature
+  # and timing of those control signals are device-specific and left for panel
+  # device tree bindings to specify. The following GPIO specifiers can however be
+  # used for panels that implement compatible control signals.
+
+  enable-gpios:
+    maxItems: 1
+    description: |
+      Specifier for a GPIO connected to the panel enable control signal. The
+      enable signal is active high and enables operation of the panel. This
+      property can also be used for panels implementing an active low power down
+      signal, which is a negated version of the enable signal. Active low enable
+      signals (or active high power down signals) can be supported by inverting
+      the GPIO specifier polarity flag.
+
+      Note that the enable signal control panel operation only and must not be
+      confused with a backlight enable signal.
+
+  reset-gpios:
+    maxItems: 1
+    description:
+      Specifier for a GPIO connected to the panel reset control signal.
+      The reset signal is active low and resets the panel internal logic
+      while active. Active high reset signals can be supported by inverting the
+      GPIO specifier polarity flag.
+
+  # Power
+  power-supply:
+    description:
+      Display panels require power to be supplied. While several panels need
+      more than one power supply with panel-specific constraints governing the
+      order and timings of the power supplies, in many cases a single power
+      supply is sufficient, either because the panel has a single power rail, or
+      because all its power rails can be driven by the same supply. In that case
+      the power-supply property specifies the supply powering the panel as a
+      phandle to a regulator.
+
+  # Backlight
+
+  # Most display panels include a backlight. Some of them also include a backlight
+  # controller exposed through a control bus such as I2C or DSI. Others expose
+  # backlight control through GPIO, PWM or other signals connected to an external
+  # backlight controller.
+
+  backlight:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      For panels whose backlight is controlled by an external backlight
+      controller, this property contains a phandle that references the
+      controller.
+
+dependencies:
+  width-mm: [ height-mm ]
+  height-mm: [ width-mm ]
+
+...
diff --git a/Documentation/devicetree/bindings/display/panel/panel.txt b/Documentation/devicetree/bindings/display/panel/panel.txt
deleted file mode 100644
index e2e6867852b8..000000000000
--- a/Documentation/devicetree/bindings/display/panel/panel.txt
+++ /dev/null
@@ -1,4 +0,0 @@ 
-Common display properties
--------------------------
-
-- rotation:	Display rotation in degrees counter clockwise (0,90,180,270)
diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt
index b2b872c710f2..e11208fb7da8 100644
--- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt
+++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt
@@ -1,28 +1 @@ 
-Simple display panel
-====================
-
-panel node
-----------
-
-Required properties:
-- power-supply: See panel-common.txt
-
-Optional properties:
-- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
-- enable-gpios: GPIO pin to enable or disable the panel
-- backlight: phandle of the backlight device attached to the panel
-- no-hpd: This panel is supposed to communicate that it's ready via HPD
-  (hot plug detect) signal, but the signal isn't hooked up so we should
-  hardcode the max delay from the panel spec when powering up the panel.
-
-Example:
-
-	panel: panel {
-		compatible = "cptt,claa101wb01";
-		ddc-i2c-bus = <&panelddc>;
-
-		power-supply = <&vdd_pnl_reg>;
-		enable-gpios = <&gpio 90 0>;
-
-		backlight = <&backlight>;
-	};
+See panel-common.yaml in this directory.