diff mbox series

[v2,3/4] gpio: Add RDA Micro GPIO controller support

Message ID 20191015173026.9962-4-manivannan.sadhasivam@linaro.org
State New
Headers show
Series Add GPIO support for RDA8810PL SoC | expand

Commit Message

Manivannan Sadhasivam Oct. 15, 2019, 5:30 p.m. UTC
Add support for GPIO controller from RDA Micro.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

---
 drivers/gpio/Kconfig    |   8 +
 drivers/gpio/Makefile   |   1 +
 drivers/gpio/gpio-rda.c | 315 ++++++++++++++++++++++++++++++++++++++++
 3 files changed, 324 insertions(+)
 create mode 100644 drivers/gpio/gpio-rda.c

-- 
2.17.1

Comments

Linus Walleij Oct. 21, 2019, 12:57 a.m. UTC | #1
On Sat, Oct 19, 2019 at 6:05 PM Manivannan Sadhasivam
<manivannan.sadhasivam@linaro.org> wrote:
> On Wed, Oct 16, 2019 at 02:41:32PM +0200, Linus Walleij wrote:


> > select GPIO_GENERIC

>

> hmm.. I don't think this driver can use it. Please see the justification

> below.

(...)
> As you can see in this driver, there are 2 separate registers needs to be

> read in order to get the value. RDA_GPIO_VAL needs to be read when the pin

> is in input state and RDA_GPIO_SET needs to be read when the pin is in output

> state.

>

> The MMIO driver relies on a single `dat` register to read the GPIO state and

> this won't fit for this driver and hence my justification for not using it.


Use RDA_GPIO_VAL for dat, then set BGPIOF_READ_OUTPUT_REG_SET
and the mmio core will do what you want I think? That's what the flag is
for IIUC.

Maybe we should document it better :/

Yours,
Linus Walleij
Manivannan Sadhasivam Oct. 21, 2019, 6:19 a.m. UTC | #2
Hi Linus,

On Mon, Oct 21, 2019 at 02:57:31AM +0200, Linus Walleij wrote:
> On Sat, Oct 19, 2019 at 6:05 PM Manivannan Sadhasivam

> <manivannan.sadhasivam@linaro.org> wrote:

> > On Wed, Oct 16, 2019 at 02:41:32PM +0200, Linus Walleij wrote:

> 

> > > select GPIO_GENERIC

> >

> > hmm.. I don't think this driver can use it. Please see the justification

> > below.

> (...)

> > As you can see in this driver, there are 2 separate registers needs to be

> > read in order to get the value. RDA_GPIO_VAL needs to be read when the pin

> > is in input state and RDA_GPIO_SET needs to be read when the pin is in output

> > state.

> >

> > The MMIO driver relies on a single `dat` register to read the GPIO state and

> > this won't fit for this driver and hence my justification for not using it.

> 

> Use RDA_GPIO_VAL for dat, then set BGPIOF_READ_OUTPUT_REG_SET

> and the mmio core will do what you want I think? That's what the flag is

> for IIUC.

> 


Ah, this should work. Sorry for missing this earlier.

> Maybe we should document it better :/

> 


That's how everything is in kernel for me... If you don't look closer, you'll
not get it.

Thanks,
Mani

> Yours,

> Linus Walleij
diff mbox series

Patch

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 38e096e6925f..71826e61fdb3 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -435,6 +435,14 @@  config GPIO_RCAR
 	help
 	  Say yes here to support GPIO on Renesas R-Car SoCs.
 
+config GPIO_RDA
+	bool "RDA Micro GPIO controller support"
+	depends on ARCH_RDA || COMPILE_TEST
+	depends on OF_GPIO
+	select GPIOLIB_IRQCHIP
+	help
+	  Say Y here to support RDA Micro GPIO controller.
+
 config GPIO_REG
 	bool
 	help
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index d2fd19c15bae..5c68c9a48fa3 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -115,6 +115,7 @@  obj-$(CONFIG_GPIO_PXA)			+= gpio-pxa.o
 obj-$(CONFIG_GPIO_RASPBERRYPI_EXP)	+= gpio-raspberrypi-exp.o
 obj-$(CONFIG_GPIO_RC5T583)		+= gpio-rc5t583.o
 obj-$(CONFIG_GPIO_RCAR)			+= gpio-rcar.o
+obj-$(CONFIG_GPIO_RDA)			+= gpio-rda.o
 obj-$(CONFIG_GPIO_RDC321X)		+= gpio-rdc321x.o
 obj-$(CONFIG_GPIO_REG)			+= gpio-reg.o
 obj-$(CONFIG_ARCH_SA1100)		+= gpio-sa1100.o
diff --git a/drivers/gpio/gpio-rda.c b/drivers/gpio/gpio-rda.c
new file mode 100644
index 000000000000..1e6ffe27897f
--- /dev/null
+++ b/drivers/gpio/gpio-rda.c
@@ -0,0 +1,315 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * RDA Micro GPIO driver
+ *
+ * Copyright (C) 2012 RDA Micro Inc.
+ * Copyright (C) 2019 Manivannan Sadhasivam
+ */
+
+#include <linux/bitops.h>
+#include <linux/gpio/driver.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+
+#define RDA_GPIO_OEN_VAL		0x00
+#define RDA_GPIO_OEN_SET_OUT		0x04
+#define RDA_GPIO_OEN_SET_IN		0x08
+#define RDA_GPIO_VAL			0x0c
+#define RDA_GPIO_SET			0x10
+#define RDA_GPIO_CLR			0x14
+#define RDA_GPIO_INT_CTRL_SET		0x18
+#define RDA_GPIO_INT_CTRL_CLR		0x1c
+#define RDA_GPIO_INT_CLR		0x20
+#define RDA_GPIO_INT_STATUS		0x24
+
+#define RDA_GPIO_IRQ_RISE_SHIFT		0
+#define RDA_GPIO_IRQ_FALL_SHIFT		8
+#define RDA_GPIO_DEBOUCE_SHIFT		16
+#define RDA_GPIO_LEVEL_SHIFT		24
+
+#define RDA_GPIO_IRQ_MASK		0xff
+
+/* Each bank consists of 32 GPIOs */
+#define RDA_GPIO_BANK_NR	32
+
+struct rda_gpio {
+	struct gpio_chip chip;
+	void __iomem *base;
+	spinlock_t lock;
+	struct irq_chip irq_chip;
+	int irq;
+};
+
+static void rda_gpio_update(struct gpio_chip *chip, unsigned int offset,
+			    u16 reg, int val)
+{
+	struct rda_gpio *rda_gpio = gpiochip_get_data(chip);
+	void __iomem *base = rda_gpio->base;
+	unsigned long flags;
+	u32 tmp;
+
+	spin_lock_irqsave(&rda_gpio->lock, flags);
+	tmp = readl_relaxed(base + reg);
+
+	if (val)
+		tmp |= BIT(offset);
+	else
+		tmp &= ~BIT(offset);
+
+	writel_relaxed(tmp, base + reg);
+	spin_unlock_irqrestore(&rda_gpio->lock, flags);
+}
+
+static int rda_gpio_direction_input(struct gpio_chip *chip, unsigned int offset)
+{
+	rda_gpio_update(chip, offset, RDA_GPIO_OEN_SET_IN, 1);
+
+	return 0;
+}
+
+static int rda_gpio_direction_output(struct gpio_chip *chip,
+				     unsigned int offset, int value)
+{
+	rda_gpio_update(chip, offset, RDA_GPIO_OEN_SET_OUT, 1);
+
+	return 0;
+}
+
+static int rda_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	struct rda_gpio *rda_gpio = gpiochip_get_data(chip);
+	void __iomem *base = rda_gpio->base;
+
+	if (readl_relaxed(base + RDA_GPIO_OEN_VAL) & BIT(offset))
+		return !!(readl_relaxed(base + RDA_GPIO_VAL) & BIT(offset));
+	else
+		return !!(readl_relaxed(base + RDA_GPIO_SET) & BIT(offset));
+}
+
+static void rda_gpio_set(struct gpio_chip *chip, unsigned int offset, int value)
+{
+	if (value)
+		rda_gpio_update(chip, offset, RDA_GPIO_SET, 1);
+	else
+		rda_gpio_update(chip, offset, RDA_GPIO_CLR, 1);
+}
+
+static void rda_gpio_irq_mask(struct irq_data *data)
+{
+	struct gpio_chip *chip = irq_data_get_irq_chip_data(data);
+	struct rda_gpio *rda_gpio = gpiochip_get_data(chip);
+	void __iomem *base = rda_gpio->base;
+	u32 offset = irqd_to_hwirq(data);
+	u32 value;
+
+	value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT;
+	value |= BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT;
+
+	writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR);
+}
+
+static void rda_gpio_irq_ack(struct irq_data *data)
+{
+	struct gpio_chip *chip = irq_data_get_irq_chip_data(data);
+	u32 offset = irqd_to_hwirq(data);
+
+	rda_gpio_update(chip, offset, RDA_GPIO_INT_CLR, 1);
+}
+
+static int rda_gpio_set_irq(struct gpio_chip *chip, u32 offset,
+			    unsigned int flow_type)
+{
+	struct rda_gpio *rda_gpio = gpiochip_get_data(chip);
+	void __iomem *base = rda_gpio->base;
+	u32 value;
+
+	switch (flow_type) {
+	case IRQ_TYPE_EDGE_RISING:
+		/* Set rising edge trigger */
+		value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT;
+		writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET);
+
+		/* Switch to edge trigger interrupt */
+		value = BIT(offset) << RDA_GPIO_LEVEL_SHIFT;
+		writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR);
+		break;
+
+	case IRQ_TYPE_EDGE_FALLING:
+		/* Set falling edge trigger */
+		value = BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT;
+		writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET);
+
+		/* Switch to edge trigger interrupt */
+		value = BIT(offset) << RDA_GPIO_LEVEL_SHIFT;
+		writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR);
+		break;
+
+	case IRQ_TYPE_EDGE_BOTH:
+		/* Set both edge trigger */
+		value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT;
+		value |= BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT;
+		writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET);
+
+		/* Switch to edge trigger interrupt */
+		value = BIT(offset) << RDA_GPIO_LEVEL_SHIFT;
+		writel_relaxed(value, base + RDA_GPIO_INT_CTRL_CLR);
+		break;
+
+	case IRQ_TYPE_LEVEL_HIGH:
+		/* Set high level trigger */
+		value = BIT(offset) << RDA_GPIO_IRQ_RISE_SHIFT;
+
+		/* Switch to level trigger interrupt */
+		value |= BIT(offset) << RDA_GPIO_LEVEL_SHIFT;
+		writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET);
+		break;
+
+	case IRQ_TYPE_LEVEL_LOW:
+		/* Set low level trigger */
+		value = BIT(offset) << RDA_GPIO_IRQ_FALL_SHIFT;
+
+		/* Switch to level trigger interrupt */
+		value |= BIT(offset) << RDA_GPIO_LEVEL_SHIFT;
+		writel_relaxed(value, base + RDA_GPIO_INT_CTRL_SET);
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void rda_gpio_irq_unmask(struct irq_data *data)
+{
+	struct gpio_chip *chip = irq_data_get_irq_chip_data(data);
+	u32 offset = irqd_to_hwirq(data);
+	u32 trigger = irqd_get_trigger_type(data);
+
+	rda_gpio_set_irq(chip, offset, trigger);
+}
+
+static int rda_gpio_irq_set_type(struct irq_data *data, unsigned int flow_type)
+{
+	struct gpio_chip *chip = irq_data_get_irq_chip_data(data);
+	u32 offset = irqd_to_hwirq(data);
+	int ret;
+
+	ret = rda_gpio_set_irq(chip, offset, flow_type);
+	if (ret)
+		return ret;
+
+	if (flow_type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH))
+		irq_set_handler_locked(data, handle_level_irq);
+	else if (flow_type & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING))
+		irq_set_handler_locked(data, handle_edge_irq);
+
+	return 0;
+}
+
+static void rda_gpio_irq_handler(struct irq_desc *desc)
+{
+	struct gpio_chip *chip = irq_desc_get_handler_data(desc);
+	struct irq_chip *ic = irq_desc_get_chip(desc);
+	struct rda_gpio *rda_gpio = gpiochip_get_data(chip);
+	unsigned long status;
+	u32 n, girq;
+
+	chained_irq_enter(ic, desc);
+
+	status = readl_relaxed(rda_gpio->base + RDA_GPIO_INT_STATUS);
+	/* Only lower 8 bits are capable of generating interrupts */
+	status &= RDA_GPIO_IRQ_MASK;
+
+	for_each_set_bit(n, &status, RDA_GPIO_BANK_NR) {
+		girq = irq_find_mapping(chip->irq.domain, n);
+		generic_handle_irq(girq);
+	}
+
+	chained_irq_exit(ic, desc);
+}
+
+static int rda_gpio_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct gpio_irq_chip *irq_chip;
+	struct rda_gpio *rda_gpio;
+	u32 ngpios;
+	int ret;
+
+	rda_gpio = devm_kzalloc(&pdev->dev, sizeof(*rda_gpio), GFP_KERNEL);
+	if (!rda_gpio)
+		return -ENOMEM;
+
+	ret = device_property_read_u32(&pdev->dev, "ngpios", &ngpios);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Not all ports have interrupt capability. For instance, on
+	 * RDA8810PL, GPIOC doesn't support interrupt. So we must handle
+	 * those also.
+	 */
+	rda_gpio->irq = platform_get_irq(pdev, 0);
+
+	rda_gpio->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(rda_gpio->base))
+		return PTR_ERR(rda_gpio->base);
+
+	spin_lock_init(&rda_gpio->lock);
+
+	rda_gpio->chip.label = dev_name(&pdev->dev);
+	rda_gpio->chip.ngpio = ngpios;
+	rda_gpio->chip.base = -1;
+	rda_gpio->chip.parent = &pdev->dev;
+	rda_gpio->chip.of_node = np;
+	rda_gpio->chip.get = rda_gpio_get;
+	rda_gpio->chip.set = rda_gpio_set;
+	rda_gpio->chip.direction_input = rda_gpio_direction_input;
+	rda_gpio->chip.direction_output = rda_gpio_direction_output;
+
+	if (rda_gpio->irq >= 0) {
+		rda_gpio->irq_chip.name = "rda-gpio",
+		rda_gpio->irq_chip.irq_ack = rda_gpio_irq_ack,
+		rda_gpio->irq_chip.irq_mask = rda_gpio_irq_mask,
+		rda_gpio->irq_chip.irq_unmask = rda_gpio_irq_unmask,
+		rda_gpio->irq_chip.irq_set_type = rda_gpio_irq_set_type,
+		rda_gpio->irq_chip.flags = IRQCHIP_SKIP_SET_WAKE,
+
+		irq_chip = &rda_gpio->chip.irq;
+		irq_chip->chip = &rda_gpio->irq_chip;
+		irq_chip->handler = handle_bad_irq;
+		irq_chip->default_type = IRQ_TYPE_NONE;
+		irq_chip->parent_handler = rda_gpio_irq_handler;
+		irq_chip->parent_handler_data = rda_gpio;
+		irq_chip->num_parents = 1;
+		irq_chip->parents = &rda_gpio->irq;
+	}
+
+	platform_set_drvdata(pdev, rda_gpio);
+
+	return devm_gpiochip_add_data(&pdev->dev, &rda_gpio->chip, rda_gpio);
+}
+
+static const struct of_device_id rda_gpio_of_match[] = {
+	{ .compatible = "rda,8810pl-gpio", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rda_gpio_of_match);
+
+static struct platform_driver rda_gpio_driver = {
+	.probe = rda_gpio_probe,
+	.driver = {
+		.name = "rda-gpio",
+		.of_match_table	= rda_gpio_of_match,
+	},
+};
+
+module_platform_driver_probe(rda_gpio_driver, rda_gpio_probe);
+
+MODULE_DESCRIPTION("RDA Micro GPIO driver");
+MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>");
+MODULE_LICENSE("GPL v2");