deleted file mode 100644
@@ -1,39 +0,0 @@
-Frame Relay (FR) support for linux is built into a two tiered system of device
-drivers. The upper layer implements RFC1490 FR specification, and uses the
-Data Link Connection Identifier (DLCI) as its hardware address. Usually these
-are assigned by your network supplier, they give you the number/numbers of
-the Virtual Connections (VC) assigned to you.
-
-Each DLCI is a point-to-point link between your machine and a remote one.
-As such, a separate device is needed to accommodate the routing. Within the
-net-tools archives is 'dlcicfg'. This program will communicate with the
-base "DLCI" device, and create new net devices named 'dlci00', 'dlci01'...
-The configuration script will ask you how many DLCIs you need, as well as
-how many DLCIs you want to assign to each Frame Relay Access Device (FRAD).
-
-The DLCI uses a number of function calls to communicate with the FRAD, all
-of which are stored in the FRAD's private data area. assoc/deassoc,
-activate/deactivate and dlci_config. The DLCI supplies a receive function
-to the FRAD to accept incoming packets.
-
-With this initial offering, only 1 FRAD driver is available. With many thanks
-to Sangoma Technologies, David Mandelstam & Gene Kozin, the S502A, S502E &
-S508 are supported. This driver is currently set up for only FR, but as
-Sangoma makes more firmware modules available, it can be updated to provide
-them as well.
-
-Configuration of the FRAD makes use of another net-tools program, 'fradcfg'.
-This program makes use of a configuration file (which dlcicfg can also read)
-to specify the types of boards to be configured as FRADs, as well as perform
-any board specific configuration. The Sangoma module of fradcfg loads the
-FR firmware into the card, sets the irq/port/memory information, and provides
-an initial configuration.
-
-Additional FRAD device drivers can be added as hardware is available.
-
-At this time, the dlcicfg and fradcfg programs have not been incorporated into
-the net-tools distribution. They can be found at ftp.invlogic.com, in
-/pub/linux. Note that with OS/2 FTPD, you end up in /pub by default, so just
-use 'cd linux'. v0.10 is for use on pre-2.0.3 and earlier, v0.15 is for
-pre-2.0.4 and later.
-
@@ -6436,12 +6436,6 @@ W: http://floatingpoint.sourceforge.net/emulator/index.html
S: Maintained
F: arch/x86/math-emu/
-FRAME RELAY DLCI/FRAD (Sangoma drivers too)
-L: netdev@vger.kernel.org
-S: Orphan
-F: drivers/net/wan/dlci.c
-F: drivers/net/wan/sdla.c
-
FRAMEBUFFER LAYER
M: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
L: dri-devel@lists.freedesktop.org
@@ -297,51 +297,6 @@ config IXP4XX_HSS
Say Y here if you want to use built-in HSS ports
on IXP4xx processor.
-config DLCI
- tristate "Frame Relay DLCI support"
- ---help---
- Support for the Frame Relay protocol.
-
- Frame Relay is a fast low-cost way to connect to a remote Internet
- access provider or to form a private wide area network. The one
- physical line from your box to the local "switch" (i.e. the entry
- point to the Frame Relay network, usually at the phone company) can
- carry several logical point-to-point connections to other computers
- connected to the Frame Relay network. For a general explanation of
- the protocol, check out <http://www.mplsforum.org/>.
-
- To use frame relay, you need supporting hardware (called FRAD) and
- certain programs from the net-tools package as explained in
- <file:Documentation/networking/framerelay.txt>.
-
- To compile this driver as a module, choose M here: the
- module will be called dlci.
-
-config DLCI_MAX
- int "Max DLCI per device"
- depends on DLCI
- default "8"
- help
- How many logical point-to-point frame relay connections (the
- identifiers of which are called DCLIs) should be handled by each
- of your hardware frame relay access devices.
-
- Go with the default.
-
-config SDLA
- tristate "SDLA (Sangoma S502/S508) support"
- depends on DLCI && ISA
- help
- Driver for the Sangoma S502A, S502E, and S508 Frame Relay Access
- Devices.
-
- These are multi-protocol cards, but only Frame Relay is supported
- by the driver at this time. Please read
- <file:Documentation/networking/framerelay.txt>.
-
- To compile this driver as a module, choose M here: the
- module will be called sdla.
-
# X.25 network drivers
config LAPBETHER
tristate "LAPB over Ethernet driver"
@@ -22,8 +22,6 @@ obj-$(CONFIG_X25_ASY) += x25_asy.o
obj-$(CONFIG_LANMEDIA) += lmc/
-obj-$(CONFIG_DLCI) += dlci.o
-obj-$(CONFIG_SDLA) += sdla.o
obj-$(CONFIG_LAPBETHER) += lapbether.o
obj-$(CONFIG_N2) += n2.o
obj-$(CONFIG_C101) += c101.o
deleted file mode 100644
@@ -1,542 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * DLCI Implementation of Frame Relay protocol for Linux, according to
- * RFC 1490. This generic device provides en/decapsulation for an
- * underlying hardware driver. Routes & IPs are assigned to these
- * interfaces. Requires 'dlcicfg' program to create usable
- * interfaces, the initial one, 'dlci' is for IOCTL use only.
- *
- * Version: @(#)dlci.c 0.35 4 Jan 1997
- *
- * Author: Mike McLagan <mike.mclagan@linux.org>
- *
- * Changes:
- *
- * 0.15 Mike Mclagan Packet freeing, bug in kmalloc call
- * DLCI_RET handling
- * 0.20 Mike McLagan More conservative on which packets
- * are returned for retry and which are
- * are dropped. If DLCI_RET_DROP is
- * returned from the FRAD, the packet is
- * sent back to Linux for re-transmission
- * 0.25 Mike McLagan Converted to use SIOC IOCTL calls
- * 0.30 Jim Freeman Fixed to allow IPX traffic
- * 0.35 Michael Elizabeth Fixed incorrect memcpy_fromfs
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/fcntl.h>
-#include <linux/interrupt.h>
-#include <linux/ptrace.h>
-#include <linux/ioport.h>
-#include <linux/in.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/netdevice.h>
-#include <linux/skbuff.h>
-#include <linux/if_arp.h>
-#include <linux/if_frad.h>
-#include <linux/bitops.h>
-
-#include <net/sock.h>
-
-#include <asm/io.h>
-#include <asm/dma.h>
-#include <linux/uaccess.h>
-
-static const char version[] = "DLCI driver v0.35, 4 Jan 1997, mike.mclagan@linux.org";
-
-static LIST_HEAD(dlci_devs);
-
-static void dlci_setup(struct net_device *);
-
-/*
- * these encapsulate the RFC 1490 requirements as well as
- * deal with packet transmission and reception, working with
- * the upper network layers
- */
-
-static int dlci_header(struct sk_buff *skb, struct net_device *dev,
- unsigned short type, const void *daddr,
- const void *saddr, unsigned len)
-{
- struct frhdr hdr;
- unsigned int hlen;
- char *dest;
-
- hdr.control = FRAD_I_UI;
- switch (type)
- {
- case ETH_P_IP:
- hdr.IP_NLPID = FRAD_P_IP;
- hlen = sizeof(hdr.control) + sizeof(hdr.IP_NLPID);
- break;
-
- /* feel free to add other types, if necessary */
-
- default:
- hdr.pad = FRAD_P_PADDING;
- hdr.NLPID = FRAD_P_SNAP;
- memset(hdr.OUI, 0, sizeof(hdr.OUI));
- hdr.PID = htons(type);
- hlen = sizeof(hdr);
- break;
- }
-
- dest = skb_push(skb, hlen);
- if (!dest)
- return 0;
-
- memcpy(dest, &hdr, hlen);
-
- return hlen;
-}
-
-static void dlci_receive(struct sk_buff *skb, struct net_device *dev)
-{
- struct frhdr *hdr;
- int process, header;
-
- if (!pskb_may_pull(skb, sizeof(*hdr))) {
- netdev_notice(dev, "invalid data no header\n");
- dev->stats.rx_errors++;
- kfree_skb(skb);
- return;
- }
-
- hdr = (struct frhdr *) skb->data;
- process = 0;
- header = 0;
- skb->dev = dev;
-
- if (hdr->control != FRAD_I_UI)
- {
- netdev_notice(dev, "Invalid header flag 0x%02X\n",
- hdr->control);
- dev->stats.rx_errors++;
- }
- else
- switch (hdr->IP_NLPID)
- {
- case FRAD_P_PADDING:
- if (hdr->NLPID != FRAD_P_SNAP)
- {
- netdev_notice(dev, "Unsupported NLPID 0x%02X\n",
- hdr->NLPID);
- dev->stats.rx_errors++;
- break;
- }
-
- if (hdr->OUI[0] + hdr->OUI[1] + hdr->OUI[2] != 0)
- {
- netdev_notice(dev, "Unsupported organizationally unique identifier 0x%02X-%02X-%02X\n",
- hdr->OUI[0],
- hdr->OUI[1],
- hdr->OUI[2]);
- dev->stats.rx_errors++;
- break;
- }
-
- /* at this point, it's an EtherType frame */
- header = sizeof(struct frhdr);
- /* Already in network order ! */
- skb->protocol = hdr->PID;
- process = 1;
- break;
-
- case FRAD_P_IP:
- header = sizeof(hdr->control) + sizeof(hdr->IP_NLPID);
- skb->protocol = htons(ETH_P_IP);
- process = 1;
- break;
-
- case FRAD_P_SNAP:
- case FRAD_P_Q933:
- case FRAD_P_CLNP:
- netdev_notice(dev, "Unsupported NLPID 0x%02X\n",
- hdr->pad);
- dev->stats.rx_errors++;
- break;
-
- default:
- netdev_notice(dev, "Invalid pad byte 0x%02X\n",
- hdr->pad);
- dev->stats.rx_errors++;
- break;
- }
-
- if (process)
- {
- /* we've set up the protocol, so discard the header */
- skb_reset_mac_header(skb);
- skb_pull(skb, header);
- dev->stats.rx_bytes += skb->len;
- netif_rx(skb);
- dev->stats.rx_packets++;
- }
- else
- dev_kfree_skb(skb);
-}
-
-static netdev_tx_t dlci_transmit(struct sk_buff *skb, struct net_device *dev)
-{
- struct dlci_local *dlp = netdev_priv(dev);
-
- if (skb) {
- struct netdev_queue *txq = skb_get_tx_queue(dev, skb);
- netdev_start_xmit(skb, dlp->slave, txq, false);
- }
- return NETDEV_TX_OK;
-}
-
-static int dlci_config(struct net_device *dev, struct dlci_conf __user *conf, int get)
-{
- struct dlci_conf config;
- struct dlci_local *dlp;
- struct frad_local *flp;
- int err;
-
- dlp = netdev_priv(dev);
-
- flp = netdev_priv(dlp->slave);
-
- if (!get)
- {
- if (copy_from_user(&config, conf, sizeof(struct dlci_conf)))
- return -EFAULT;
- if (config.flags & ~DLCI_VALID_FLAGS)
- return -EINVAL;
- memcpy(&dlp->config, &config, sizeof(struct dlci_conf));
- dlp->configured = 1;
- }
-
- err = (*flp->dlci_conf)(dlp->slave, dev, get);
- if (err)
- return err;
-
- if (get)
- {
- if (copy_to_user(conf, &dlp->config, sizeof(struct dlci_conf)))
- return -EFAULT;
- }
-
- return 0;
-}
-
-static int dlci_dev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
-{
- struct dlci_local *dlp;
-
- if (!capable(CAP_NET_ADMIN))
- return -EPERM;
-
- dlp = netdev_priv(dev);
-
- switch (cmd)
- {
- case DLCI_GET_SLAVE:
- if (!*(short *)(dev->dev_addr))
- return -EINVAL;
-
- strncpy(ifr->ifr_slave, dlp->slave->name, sizeof(ifr->ifr_slave));
- break;
-
- case DLCI_GET_CONF:
- case DLCI_SET_CONF:
- if (!*(short *)(dev->dev_addr))
- return -EINVAL;
-
- return dlci_config(dev, ifr->ifr_data, cmd == DLCI_GET_CONF);
-
- default:
- return -EOPNOTSUPP;
- }
- return 0;
-}
-
-static int dlci_change_mtu(struct net_device *dev, int new_mtu)
-{
- struct dlci_local *dlp = netdev_priv(dev);
-
- return dev_set_mtu(dlp->slave, new_mtu);
-}
-
-static int dlci_open(struct net_device *dev)
-{
- struct dlci_local *dlp;
- struct frad_local *flp;
- int err;
-
- dlp = netdev_priv(dev);
-
- if (!*(short *)(dev->dev_addr))
- return -EINVAL;
-
- if (!netif_running(dlp->slave))
- return -ENOTCONN;
-
- flp = netdev_priv(dlp->slave);
- err = (*flp->activate)(dlp->slave, dev);
- if (err)
- return err;
-
- netif_start_queue(dev);
-
- return 0;
-}
-
-static int dlci_close(struct net_device *dev)
-{
- struct dlci_local *dlp;
- struct frad_local *flp;
- int err;
-
- netif_stop_queue(dev);
-
- dlp = netdev_priv(dev);
-
- flp = netdev_priv(dlp->slave);
- err = (*flp->deactivate)(dlp->slave, dev);
-
- return 0;
-}
-
-static int dlci_add(struct dlci_add *dlci)
-{
- struct net_device *master, *slave;
- struct dlci_local *dlp;
- struct frad_local *flp;
- int err = -EINVAL;
-
-
- /* validate slave device */
- slave = dev_get_by_name(&init_net, dlci->devname);
- if (!slave)
- return -ENODEV;
-
- if (slave->type != ARPHRD_FRAD || netdev_priv(slave) == NULL)
- goto err1;
-
- /* create device name */
- master = alloc_netdev(sizeof(struct dlci_local), "dlci%d",
- NET_NAME_UNKNOWN, dlci_setup);
- if (!master) {
- err = -ENOMEM;
- goto err1;
- }
-
- /* make sure same slave not already registered */
- rtnl_lock();
- list_for_each_entry(dlp, &dlci_devs, list) {
- if (dlp->slave == slave) {
- err = -EBUSY;
- goto err2;
- }
- }
-
- *(short *)(master->dev_addr) = dlci->dlci;
-
- dlp = netdev_priv(master);
- dlp->slave = slave;
- dlp->master = master;
-
- flp = netdev_priv(slave);
- err = (*flp->assoc)(slave, master);
- if (err < 0)
- goto err2;
-
- err = register_netdevice(master);
- if (err < 0)
- goto err2;
-
- strcpy(dlci->devname, master->name);
-
- list_add(&dlp->list, &dlci_devs);
- rtnl_unlock();
-
- return 0;
-
- err2:
- rtnl_unlock();
- free_netdev(master);
- err1:
- dev_put(slave);
- return err;
-}
-
-static int dlci_del(struct dlci_add *dlci)
-{
- struct dlci_local *dlp;
- struct frad_local *flp;
- struct net_device *master, *slave;
- int err;
- bool found = false;
-
- rtnl_lock();
-
- /* validate slave device */
- master = __dev_get_by_name(&init_net, dlci->devname);
- if (!master) {
- err = -ENODEV;
- goto out;
- }
-
- list_for_each_entry(dlp, &dlci_devs, list) {
- if (dlp->master == master) {
- found = true;
- break;
- }
- }
- if (!found) {
- err = -ENODEV;
- goto out;
- }
-
- if (netif_running(master)) {
- err = -EBUSY;
- goto out;
- }
-
- dlp = netdev_priv(master);
- slave = dlp->slave;
- flp = netdev_priv(slave);
-
- err = (*flp->deassoc)(slave, master);
- if (!err) {
- list_del(&dlp->list);
-
- unregister_netdevice(master);
-
- dev_put(slave);
- }
-out:
- rtnl_unlock();
- return err;
-}
-
-static int dlci_ioctl(unsigned int cmd, void __user *arg)
-{
- struct dlci_add add;
- int err;
-
- if (!capable(CAP_NET_ADMIN))
- return -EPERM;
-
- if (copy_from_user(&add, arg, sizeof(struct dlci_add)))
- return -EFAULT;
-
- switch (cmd)
- {
- case SIOCADDDLCI:
- err = dlci_add(&add);
-
- if (!err)
- if (copy_to_user(arg, &add, sizeof(struct dlci_add)))
- return -EFAULT;
- break;
-
- case SIOCDELDLCI:
- err = dlci_del(&add);
- break;
-
- default:
- err = -EINVAL;
- }
-
- return err;
-}
-
-static const struct header_ops dlci_header_ops = {
- .create = dlci_header,
-};
-
-static const struct net_device_ops dlci_netdev_ops = {
- .ndo_open = dlci_open,
- .ndo_stop = dlci_close,
- .ndo_do_ioctl = dlci_dev_ioctl,
- .ndo_start_xmit = dlci_transmit,
- .ndo_change_mtu = dlci_change_mtu,
-};
-
-static void dlci_setup(struct net_device *dev)
-{
- struct dlci_local *dlp = netdev_priv(dev);
-
- dev->flags = 0;
- dev->header_ops = &dlci_header_ops;
- dev->netdev_ops = &dlci_netdev_ops;
- dev->needs_free_netdev = true;
-
- dlp->receive = dlci_receive;
-
- dev->type = ARPHRD_DLCI;
- dev->hard_header_len = sizeof(struct frhdr);
- dev->addr_len = sizeof(short);
-
-}
-
-/* if slave is unregistering, then cleanup master */
-static int dlci_dev_event(struct notifier_block *unused,
- unsigned long event, void *ptr)
-{
- struct net_device *dev = netdev_notifier_info_to_dev(ptr);
-
- if (dev_net(dev) != &init_net)
- return NOTIFY_DONE;
-
- if (event == NETDEV_UNREGISTER) {
- struct dlci_local *dlp;
-
- list_for_each_entry(dlp, &dlci_devs, list) {
- if (dlp->slave == dev) {
- list_del(&dlp->list);
- unregister_netdevice(dlp->master);
- dev_put(dlp->slave);
- break;
- }
- }
- }
- return NOTIFY_DONE;
-}
-
-static struct notifier_block dlci_notifier = {
- .notifier_call = dlci_dev_event,
-};
-
-static int __init init_dlci(void)
-{
- dlci_ioctl_set(dlci_ioctl);
- register_netdevice_notifier(&dlci_notifier);
-
- printk("%s.\n", version);
-
- return 0;
-}
-
-static void __exit dlci_exit(void)
-{
- struct dlci_local *dlp, *nxt;
-
- dlci_ioctl_set(NULL);
- unregister_netdevice_notifier(&dlci_notifier);
-
- rtnl_lock();
- list_for_each_entry_safe(dlp, nxt, &dlci_devs, list) {
- unregister_netdevice(dlp->master);
- dev_put(dlp->slave);
- }
- rtnl_unlock();
-}
-
-module_init(init_dlci);
-module_exit(dlci_exit);
-
-MODULE_AUTHOR("Mike McLagan");
-MODULE_DESCRIPTION("Frame Relay DLCI layer");
-MODULE_LICENSE("GPL");
deleted file mode 100644
@@ -1,1655 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * SDLA An implementation of a driver for the Sangoma S502/S508 series
- * multi-protocol PC interface card. Initial offering is with
- * the DLCI driver, providing Frame Relay support for linux.
- *
- * Global definitions for the Frame relay interface.
- *
- * Version: @(#)sdla.c 0.30 12 Sep 1996
- *
- * Credits: Sangoma Technologies, for the use of 2 cards for an extended
- * period of time.
- * David Mandelstam <dm@sangoma.com> for getting me started on
- * this project, and incentive to complete it.
- * Gene Kozen <74604.152@compuserve.com> for providing me with
- * important information about the cards.
- *
- * Author: Mike McLagan <mike.mclagan@linux.org>
- *
- * Changes:
- * 0.15 Mike McLagan Improved error handling, packet dropping
- * 0.20 Mike McLagan New transmit/receive flags for config
- * If in FR mode, don't accept packets from
- * non DLCI devices.
- * 0.25 Mike McLagan Fixed problem with rejecting packets
- * from non DLCI devices.
- * 0.30 Mike McLagan Fixed kernel panic when used with modified
- * ifconfig
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/fcntl.h>
-#include <linux/interrupt.h>
-#include <linux/ptrace.h>
-#include <linux/ioport.h>
-#include <linux/in.h>
-#include <linux/slab.h>
-#include <linux/string.h>
-#include <linux/timer.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/netdevice.h>
-#include <linux/skbuff.h>
-#include <linux/if_arp.h>
-#include <linux/if_frad.h>
-#include <linux/sdla.h>
-#include <linux/bitops.h>
-
-#include <asm/io.h>
-#include <asm/dma.h>
-#include <linux/uaccess.h>
-
-static const char* version = "SDLA driver v0.30, 12 Sep 1996, mike.mclagan@linux.org";
-
-static unsigned int valid_port[] = { 0x250, 0x270, 0x280, 0x300, 0x350, 0x360, 0x380, 0x390};
-
-static unsigned int valid_mem[] = {
- 0xA0000, 0xA2000, 0xA4000, 0xA6000, 0xA8000, 0xAA000, 0xAC000, 0xAE000,
- 0xB0000, 0xB2000, 0xB4000, 0xB6000, 0xB8000, 0xBA000, 0xBC000, 0xBE000,
- 0xC0000, 0xC2000, 0xC4000, 0xC6000, 0xC8000, 0xCA000, 0xCC000, 0xCE000,
- 0xD0000, 0xD2000, 0xD4000, 0xD6000, 0xD8000, 0xDA000, 0xDC000, 0xDE000,
- 0xE0000, 0xE2000, 0xE4000, 0xE6000, 0xE8000, 0xEA000, 0xEC000, 0xEE000};
-
-static DEFINE_SPINLOCK(sdla_lock);
-
-/*********************************************************
- *
- * these are the core routines that access the card itself
- *
- *********************************************************/
-
-#define SDLA_WINDOW(dev,addr) outb((((addr) >> 13) & 0x1F), (dev)->base_addr + SDLA_REG_Z80_WINDOW)
-
-static void __sdla_read(struct net_device *dev, int addr, void *buf, short len)
-{
- char *temp;
- const void *base;
- int offset, bytes;
-
- temp = buf;
- while(len)
- {
- offset = addr & SDLA_ADDR_MASK;
- bytes = offset + len > SDLA_WINDOW_SIZE ? SDLA_WINDOW_SIZE - offset : len;
- base = (const void *) (dev->mem_start + offset);
-
- SDLA_WINDOW(dev, addr);
- memcpy(temp, base, bytes);
-
- addr += bytes;
- temp += bytes;
- len -= bytes;
- }
-}
-
-static void sdla_read(struct net_device *dev, int addr, void *buf, short len)
-{
- unsigned long flags;
- spin_lock_irqsave(&sdla_lock, flags);
- __sdla_read(dev, addr, buf, len);
- spin_unlock_irqrestore(&sdla_lock, flags);
-}
-
-static void __sdla_write(struct net_device *dev, int addr,
- const void *buf, short len)
-{
- const char *temp;
- void *base;
- int offset, bytes;
-
- temp = buf;
- while(len)
- {
- offset = addr & SDLA_ADDR_MASK;
- bytes = offset + len > SDLA_WINDOW_SIZE ? SDLA_WINDOW_SIZE - offset : len;
- base = (void *) (dev->mem_start + offset);
-
- SDLA_WINDOW(dev, addr);
- memcpy(base, temp, bytes);
-
- addr += bytes;
- temp += bytes;
- len -= bytes;
- }
-}
-
-static void sdla_write(struct net_device *dev, int addr,
- const void *buf, short len)
-{
- unsigned long flags;
-
- spin_lock_irqsave(&sdla_lock, flags);
- __sdla_write(dev, addr, buf, len);
- spin_unlock_irqrestore(&sdla_lock, flags);
-}
-
-
-static void sdla_clear(struct net_device *dev)
-{
- unsigned long flags;
- char *base;
- int len, addr, bytes;
-
- len = 65536;
- addr = 0;
- bytes = SDLA_WINDOW_SIZE;
- base = (void *) dev->mem_start;
-
- spin_lock_irqsave(&sdla_lock, flags);
- while(len)
- {
- SDLA_WINDOW(dev, addr);
- memset(base, 0, bytes);
-
- addr += bytes;
- len -= bytes;
- }
- spin_unlock_irqrestore(&sdla_lock, flags);
-
-}
-
-static char sdla_byte(struct net_device *dev, int addr)
-{
- unsigned long flags;
- char byte, *temp;
-
- temp = (void *) (dev->mem_start + (addr & SDLA_ADDR_MASK));
-
- spin_lock_irqsave(&sdla_lock, flags);
- SDLA_WINDOW(dev, addr);
- byte = *temp;
- spin_unlock_irqrestore(&sdla_lock, flags);
-
- return byte;
-}
-
-static void sdla_stop(struct net_device *dev)
-{
- struct frad_local *flp;
-
- flp = netdev_priv(dev);
- switch(flp->type)
- {
- case SDLA_S502A:
- outb(SDLA_S502A_HALT, dev->base_addr + SDLA_REG_CONTROL);
- flp->state = SDLA_HALT;
- break;
- case SDLA_S502E:
- outb(SDLA_HALT, dev->base_addr + SDLA_REG_Z80_CONTROL);
- outb(SDLA_S502E_ENABLE, dev->base_addr + SDLA_REG_CONTROL);
- flp->state = SDLA_S502E_ENABLE;
- break;
- case SDLA_S507:
- flp->state &= ~SDLA_CPUEN;
- outb(flp->state, dev->base_addr + SDLA_REG_CONTROL);
- break;
- case SDLA_S508:
- flp->state &= ~SDLA_CPUEN;
- outb(flp->state, dev->base_addr + SDLA_REG_CONTROL);
- break;
- }
-}
-
-static void sdla_start(struct net_device *dev)
-{
- struct frad_local *flp;
-
- flp = netdev_priv(dev);
- switch(flp->type)
- {
- case SDLA_S502A:
- outb(SDLA_S502A_NMI, dev->base_addr + SDLA_REG_CONTROL);
- outb(SDLA_S502A_START, dev->base_addr + SDLA_REG_CONTROL);
- flp->state = SDLA_S502A_START;
- break;
- case SDLA_S502E:
- outb(SDLA_S502E_CPUEN, dev->base_addr + SDLA_REG_Z80_CONTROL);
- outb(0x00, dev->base_addr + SDLA_REG_CONTROL);
- flp->state = 0;
- break;
- case SDLA_S507:
- flp->state |= SDLA_CPUEN;
- outb(flp->state, dev->base_addr + SDLA_REG_CONTROL);
- break;
- case SDLA_S508:
- flp->state |= SDLA_CPUEN;
- outb(flp->state, dev->base_addr + SDLA_REG_CONTROL);
- break;
- }
-}
-
-/****************************************************
- *
- * this is used for the S502A/E cards to determine
- * the speed of the onboard CPU. Calibration is
- * necessary for the Frame Relay code uploaded
- * later. Incorrect results cause timing problems
- * with link checks & status messages
- *
- ***************************************************/
-
-static int sdla_z80_poll(struct net_device *dev, int z80_addr, int jiffs, char resp1, char resp2)
-{
- unsigned long start, done, now;
- char resp, *temp;
-
- start = now = jiffies;
- done = jiffies + jiffs;
-
- temp = (void *)dev->mem_start;
- temp += z80_addr & SDLA_ADDR_MASK;
-
- resp = ~resp1;
- while (time_before(jiffies, done) && (resp != resp1) && (!resp2 || (resp != resp2)))
- {
- if (jiffies != now)
- {
- SDLA_WINDOW(dev, z80_addr);
- now = jiffies;
- resp = *temp;
- }
- }
- return time_before(jiffies, done) ? jiffies - start : -1;
-}
-
-/* constants for Z80 CPU speed */
-#define Z80_READY '1' /* Z80 is ready to begin */
-#define LOADER_READY '2' /* driver is ready to begin */
-#define Z80_SCC_OK '3' /* SCC is on board */
-#define Z80_SCC_BAD '4' /* SCC was not found */
-
-static int sdla_cpuspeed(struct net_device *dev, struct ifreq *ifr)
-{
- int jiffs;
- char data;
-
- sdla_start(dev);
- if (sdla_z80_poll(dev, 0, 3*HZ, Z80_READY, 0) < 0)
- return -EIO;
-
- data = LOADER_READY;
- sdla_write(dev, 0, &data, 1);
-
- if ((jiffs = sdla_z80_poll(dev, 0, 8*HZ, Z80_SCC_OK, Z80_SCC_BAD)) < 0)
- return -EIO;
-
- sdla_stop(dev);
- sdla_read(dev, 0, &data, 1);
-
- if (data == Z80_SCC_BAD)
- {
- printk("%s: SCC bad\n", dev->name);
- return -EIO;
- }
-
- if (data != Z80_SCC_OK)
- return -EINVAL;
-
- if (jiffs < 165)
- ifr->ifr_mtu = SDLA_CPU_16M;
- else if (jiffs < 220)
- ifr->ifr_mtu = SDLA_CPU_10M;
- else if (jiffs < 258)
- ifr->ifr_mtu = SDLA_CPU_8M;
- else if (jiffs < 357)
- ifr->ifr_mtu = SDLA_CPU_7M;
- else if (jiffs < 467)
- ifr->ifr_mtu = SDLA_CPU_5M;
- else
- ifr->ifr_mtu = SDLA_CPU_3M;
-
- return 0;
-}
-
-/************************************************
- *
- * Direct interaction with the Frame Relay code
- * starts here.
- *
- ************************************************/
-
-struct _dlci_stat
-{
- short dlci;
- char flags;
-} __packed;
-
-struct _frad_stat
-{
- char flags;
- struct _dlci_stat dlcis[SDLA_MAX_DLCI];
-};
-
-static void sdla_errors(struct net_device *dev, int cmd, int dlci, int ret, int len, void *data)
-{
- struct _dlci_stat *pstatus;
- short *pdlci;
- int i;
- char *state, line[30];
-
- switch (ret)
- {
- case SDLA_RET_MODEM:
- state = data;
- if (*state & SDLA_MODEM_DCD_LOW)
- netdev_info(dev, "Modem DCD unexpectedly low!\n");
- if (*state & SDLA_MODEM_CTS_LOW)
- netdev_info(dev, "Modem CTS unexpectedly low!\n");
- /* I should probably do something about this! */
- break;
-
- case SDLA_RET_CHANNEL_OFF:
- netdev_info(dev, "Channel became inoperative!\n");
- /* same here */
- break;
-
- case SDLA_RET_CHANNEL_ON:
- netdev_info(dev, "Channel became operative!\n");
- /* same here */
- break;
-
- case SDLA_RET_DLCI_STATUS:
- netdev_info(dev, "Status change reported by Access Node\n");
- len /= sizeof(struct _dlci_stat);
- for(pstatus = data, i=0;i < len;i++,pstatus++)
- {
- if (pstatus->flags & SDLA_DLCI_NEW)
- state = "new";
- else if (pstatus->flags & SDLA_DLCI_DELETED)
- state = "deleted";
- else if (pstatus->flags & SDLA_DLCI_ACTIVE)
- state = "active";
- else
- {
- sprintf(line, "unknown status: %02X", pstatus->flags);
- state = line;
- }
- netdev_info(dev, "DLCI %i: %s\n",
- pstatus->dlci, state);
- /* same here */
- }
- break;
-
- case SDLA_RET_DLCI_UNKNOWN:
- netdev_info(dev, "Received unknown DLCIs:");
- len /= sizeof(short);
- for(pdlci = data,i=0;i < len;i++,pdlci++)
- pr_cont(" %i", *pdlci);
- pr_cont("\n");
- break;
-
- case SDLA_RET_TIMEOUT:
- netdev_err(dev, "Command timed out!\n");
- break;
-
- case SDLA_RET_BUF_OVERSIZE:
- netdev_info(dev, "Bc/CIR overflow, acceptable size is %i\n",
- len);
- break;
-
- case SDLA_RET_BUF_TOO_BIG:
- netdev_info(dev, "Buffer size over specified max of %i\n",
- len);
- break;
-
- case SDLA_RET_CHANNEL_INACTIVE:
- case SDLA_RET_DLCI_INACTIVE:
- case SDLA_RET_CIR_OVERFLOW:
- case SDLA_RET_NO_BUFS:
- if (cmd == SDLA_INFORMATION_WRITE)
- break;
- /* Else, fall through */
-
- default:
- netdev_dbg(dev, "Cmd 0x%02X generated return code 0x%02X\n",
- cmd, ret);
- /* Further processing could be done here */
- break;
- }
-}
-
-static int sdla_cmd(struct net_device *dev, int cmd, short dlci, short flags,
- void *inbuf, short inlen, void *outbuf, short *outlen)
-{
- static struct _frad_stat status;
- struct frad_local *flp;
- struct sdla_cmd *cmd_buf;
- unsigned long pflags;
- unsigned long jiffs;
- int ret, waiting, len;
- long window;
-
- flp = netdev_priv(dev);
- window = flp->type == SDLA_S508 ? SDLA_508_CMD_BUF : SDLA_502_CMD_BUF;
- cmd_buf = (struct sdla_cmd *)(dev->mem_start + (window & SDLA_ADDR_MASK));
- ret = 0;
- len = 0;
- jiffs = jiffies + HZ; /* 1 second is plenty */
-
- spin_lock_irqsave(&sdla_lock, pflags);
- SDLA_WINDOW(dev, window);
- cmd_buf->cmd = cmd;
- cmd_buf->dlci = dlci;
- cmd_buf->flags = flags;
-
- if (inbuf)
- memcpy(cmd_buf->data, inbuf, inlen);
-
- cmd_buf->length = inlen;
-
- cmd_buf->opp_flag = 1;
- spin_unlock_irqrestore(&sdla_lock, pflags);
-
- waiting = 1;
- len = 0;
- while (waiting && time_before_eq(jiffies, jiffs))
- {
- if (waiting++ % 3)
- {
- spin_lock_irqsave(&sdla_lock, pflags);
- SDLA_WINDOW(dev, window);
- waiting = ((volatile int)(cmd_buf->opp_flag));
- spin_unlock_irqrestore(&sdla_lock, pflags);
- }
- }
-
- if (!waiting)
- {
-
- spin_lock_irqsave(&sdla_lock, pflags);
- SDLA_WINDOW(dev, window);
- ret = cmd_buf->retval;
- len = cmd_buf->length;
- if (outbuf && outlen)
- {
- *outlen = *outlen >= len ? len : *outlen;
-
- if (*outlen)
- memcpy(outbuf, cmd_buf->data, *outlen);
- }
-
- /* This is a local copy that's used for error handling */
- if (ret)
- memcpy(&status, cmd_buf->data, len > sizeof(status) ? sizeof(status) : len);
-
- spin_unlock_irqrestore(&sdla_lock, pflags);
- }
- else
- ret = SDLA_RET_TIMEOUT;
-
- if (ret != SDLA_RET_OK)
- sdla_errors(dev, cmd, dlci, ret, len, &status);
-
- return ret;
-}
-
-/***********************************************
- *
- * these functions are called by the DLCI driver
- *
- ***********************************************/
-
-static int sdla_reconfig(struct net_device *dev);
-
-static int sdla_activate(struct net_device *slave, struct net_device *master)
-{
- struct frad_local *flp;
- int i;
-
- flp = netdev_priv(slave);
-
- for(i=0;i<CONFIG_DLCI_MAX;i++)
- if (flp->master[i] == master)
- break;
-
- if (i == CONFIG_DLCI_MAX)
- return -ENODEV;
-
- flp->dlci[i] = abs(flp->dlci[i]);
-
- if (netif_running(slave) && (flp->config.station == FRAD_STATION_NODE))
- sdla_cmd(slave, SDLA_ACTIVATE_DLCI, 0, 0, &flp->dlci[i], sizeof(short), NULL, NULL);
-
- return 0;
-}
-
-static int sdla_deactivate(struct net_device *slave, struct net_device *master)
-{
- struct frad_local *flp;
- int i;
-
- flp = netdev_priv(slave);
-
- for(i=0;i<CONFIG_DLCI_MAX;i++)
- if (flp->master[i] == master)
- break;
-
- if (i == CONFIG_DLCI_MAX)
- return -ENODEV;
-
- flp->dlci[i] = -abs(flp->dlci[i]);
-
- if (netif_running(slave) && (flp->config.station == FRAD_STATION_NODE))
- sdla_cmd(slave, SDLA_DEACTIVATE_DLCI, 0, 0, &flp->dlci[i], sizeof(short), NULL, NULL);
-
- return 0;
-}
-
-static int sdla_assoc(struct net_device *slave, struct net_device *master)
-{
- struct frad_local *flp;
- int i;
-
- if (master->type != ARPHRD_DLCI)
- return -EINVAL;
-
- flp = netdev_priv(slave);
-
- for(i=0;i<CONFIG_DLCI_MAX;i++)
- {
- if (!flp->master[i])
- break;
- if (abs(flp->dlci[i]) == *(short *)(master->dev_addr))
- return -EADDRINUSE;
- }
-
- if (i == CONFIG_DLCI_MAX)
- return -EMLINK; /* #### Alan: Comments on this ?? */
-
-
- flp->master[i] = master;
- flp->dlci[i] = -*(short *)(master->dev_addr);
- master->mtu = slave->mtu;
-
- if (netif_running(slave)) {
- if (flp->config.station == FRAD_STATION_CPE)
- sdla_reconfig(slave);
- else
- sdla_cmd(slave, SDLA_ADD_DLCI, 0, 0, master->dev_addr, sizeof(short), NULL, NULL);
- }
-
- return 0;
-}
-
-static int sdla_deassoc(struct net_device *slave, struct net_device *master)
-{
- struct frad_local *flp;
- int i;
-
- flp = netdev_priv(slave);
-
- for(i=0;i<CONFIG_DLCI_MAX;i++)
- if (flp->master[i] == master)
- break;
-
- if (i == CONFIG_DLCI_MAX)
- return -ENODEV;
-
- flp->master[i] = NULL;
- flp->dlci[i] = 0;
-
-
- if (netif_running(slave)) {
- if (flp->config.station == FRAD_STATION_CPE)
- sdla_reconfig(slave);
- else
- sdla_cmd(slave, SDLA_DELETE_DLCI, 0, 0, master->dev_addr, sizeof(short), NULL, NULL);
- }
-
- return 0;
-}
-
-static int sdla_dlci_conf(struct net_device *slave, struct net_device *master, int get)
-{
- struct frad_local *flp;
- struct dlci_local *dlp;
- int i;
- short len, ret;
-
- flp = netdev_priv(slave);
-
- for(i=0;i<CONFIG_DLCI_MAX;i++)
- if (flp->master[i] == master)
- break;
-
- if (i == CONFIG_DLCI_MAX)
- return -ENODEV;
-
- dlp = netdev_priv(master);
-
- ret = SDLA_RET_OK;
- len = sizeof(struct dlci_conf);
- if (netif_running(slave)) {
- if (get)
- ret = sdla_cmd(slave, SDLA_READ_DLCI_CONFIGURATION, abs(flp->dlci[i]), 0,
- NULL, 0, &dlp->config, &len);
- else
- ret = sdla_cmd(slave, SDLA_SET_DLCI_CONFIGURATION, abs(flp->dlci[i]), 0,
- &dlp->config, sizeof(struct dlci_conf) - 4 * sizeof(short), NULL, NULL);
- }
-
- return ret == SDLA_RET_OK ? 0 : -EIO;
-}
-
-/**************************
- *
- * now for the Linux driver
- *
- **************************/
-
-/* NOTE: the DLCI driver deals with freeing the SKB!! */
-static netdev_tx_t sdla_transmit(struct sk_buff *skb,
- struct net_device *dev)
-{
- struct frad_local *flp;
- int ret, addr, accept, i;
- short size;
- unsigned long flags;
- struct buf_entry *pbuf;
-
- flp = netdev_priv(dev);
- ret = 0;
- accept = 1;
-
- netif_stop_queue(dev);
-
- /*
- * stupid GateD insists on setting up the multicast router thru us
- * and we're ill equipped to handle a non Frame Relay packet at this
- * time!
- */
-
- accept = 1;
- switch (dev->type)
- {
- case ARPHRD_FRAD:
- if (skb->dev->type != ARPHRD_DLCI)
- {
- netdev_warn(dev, "Non DLCI device, type %i, tried to send on FRAD module\n",
- skb->dev->type);
- accept = 0;
- }
- break;
- default:
- netdev_warn(dev, "unknown firmware type 0x%04X\n",
- dev->type);
- accept = 0;
- break;
- }
- if (accept)
- {
- /* this is frame specific, but till there's a PPP module, it's the default */
- switch (flp->type)
- {
- case SDLA_S502A:
- case SDLA_S502E:
- ret = sdla_cmd(dev, SDLA_INFORMATION_WRITE, *(short *)(skb->dev->dev_addr), 0, skb->data, skb->len, NULL, NULL);
- break;
- case SDLA_S508:
- size = sizeof(addr);
- ret = sdla_cmd(dev, SDLA_INFORMATION_WRITE, *(short *)(skb->dev->dev_addr), 0, NULL, skb->len, &addr, &size);
- if (ret == SDLA_RET_OK)
- {
-
- spin_lock_irqsave(&sdla_lock, flags);
- SDLA_WINDOW(dev, addr);
- pbuf = (void *)(((int) dev->mem_start) + (addr & SDLA_ADDR_MASK));
- __sdla_write(dev, pbuf->buf_addr, skb->data, skb->len);
- SDLA_WINDOW(dev, addr);
- pbuf->opp_flag = 1;
- spin_unlock_irqrestore(&sdla_lock, flags);
- }
- break;
- }
-
- switch (ret)
- {
- case SDLA_RET_OK:
- dev->stats.tx_packets++;
- break;
-
- case SDLA_RET_CIR_OVERFLOW:
- case SDLA_RET_BUF_OVERSIZE:
- case SDLA_RET_NO_BUFS:
- dev->stats.tx_dropped++;
- break;
-
- default:
- dev->stats.tx_errors++;
- break;
- }
- }
- netif_wake_queue(dev);
- for(i=0;i<CONFIG_DLCI_MAX;i++)
- {
- if(flp->master[i]!=NULL)
- netif_wake_queue(flp->master[i]);
- }
-
- dev_kfree_skb(skb);
- return NETDEV_TX_OK;
-}
-
-static void sdla_receive(struct net_device *dev)
-{
- struct net_device *master;
- struct frad_local *flp;
- struct dlci_local *dlp;
- struct sk_buff *skb;
-
- struct sdla_cmd *cmd;
- struct buf_info *pbufi;
- struct buf_entry *pbuf;
-
- unsigned long flags;
- int i=0, received, success, addr, buf_base, buf_top;
- short dlci, len, len2, split;
-
- flp = netdev_priv(dev);
- success = 1;
- received = addr = buf_top = buf_base = 0;
- len = dlci = 0;
- skb = NULL;
- master = NULL;
- cmd = NULL;
- pbufi = NULL;
- pbuf = NULL;
-
- spin_lock_irqsave(&sdla_lock, flags);
-
- switch (flp->type)
- {
- case SDLA_S502A:
- case SDLA_S502E:
- cmd = (void *) (dev->mem_start + (SDLA_502_RCV_BUF & SDLA_ADDR_MASK));
- SDLA_WINDOW(dev, SDLA_502_RCV_BUF);
- success = cmd->opp_flag;
- if (!success)
- break;
-
- dlci = cmd->dlci;
- len = cmd->length;
- break;
-
- case SDLA_S508:
- pbufi = (void *) (dev->mem_start + (SDLA_508_RXBUF_INFO & SDLA_ADDR_MASK));
- SDLA_WINDOW(dev, SDLA_508_RXBUF_INFO);
- pbuf = (void *) (dev->mem_start + ((pbufi->rse_base + flp->buffer * sizeof(struct buf_entry)) & SDLA_ADDR_MASK));
- success = pbuf->opp_flag;
- if (!success)
- break;
-
- buf_top = pbufi->buf_top;
- buf_base = pbufi->buf_base;
- dlci = pbuf->dlci;
- len = pbuf->length;
- addr = pbuf->buf_addr;
- break;
- }
-
- /* common code, find the DLCI and get the SKB */
- if (success)
- {
- for (i=0;i<CONFIG_DLCI_MAX;i++)
- if (flp->dlci[i] == dlci)
- break;
-
- if (i == CONFIG_DLCI_MAX)
- {
- netdev_notice(dev, "Received packet from invalid DLCI %i, ignoring\n",
- dlci);
- dev->stats.rx_errors++;
- success = 0;
- }
- }
-
- if (success)
- {
- master = flp->master[i];
- skb = dev_alloc_skb(len + sizeof(struct frhdr));
- if (skb == NULL)
- {
- netdev_notice(dev, "Memory squeeze, dropping packet\n");
- dev->stats.rx_dropped++;
- success = 0;
- }
- else
- skb_reserve(skb, sizeof(struct frhdr));
- }
-
- /* pick up the data */
- switch (flp->type)
- {
- case SDLA_S502A:
- case SDLA_S502E:
- if (success)
- __sdla_read(dev, SDLA_502_RCV_BUF + SDLA_502_DATA_OFS, skb_put(skb,len), len);
-
- SDLA_WINDOW(dev, SDLA_502_RCV_BUF);
- cmd->opp_flag = 0;
- break;
-
- case SDLA_S508:
- if (success)
- {
- /* is this buffer split off the end of the internal ring buffer */
- split = addr + len > buf_top + 1 ? len - (buf_top - addr + 1) : 0;
- len2 = len - split;
-
- __sdla_read(dev, addr, skb_put(skb, len2), len2);
- if (split)
- __sdla_read(dev, buf_base, skb_put(skb, split), split);
- }
-
- /* increment the buffer we're looking at */
- SDLA_WINDOW(dev, SDLA_508_RXBUF_INFO);
- flp->buffer = (flp->buffer + 1) % pbufi->rse_num;
- pbuf->opp_flag = 0;
- break;
- }
-
- if (success)
- {
- dev->stats.rx_packets++;
- dlp = netdev_priv(master);
- (*dlp->receive)(skb, master);
- }
-
- spin_unlock_irqrestore(&sdla_lock, flags);
-}
-
-static irqreturn_t sdla_isr(int dummy, void *dev_id)
-{
- struct net_device *dev;
- struct frad_local *flp;
- char byte;
-
- dev = dev_id;
-
- flp = netdev_priv(dev);
-
- if (!flp->initialized)
- {
- netdev_warn(dev, "irq %d for uninitialized device\n", dev->irq);
- return IRQ_NONE;
- }
-
- byte = sdla_byte(dev, flp->type == SDLA_S508 ? SDLA_508_IRQ_INTERFACE : SDLA_502_IRQ_INTERFACE);
- switch (byte)
- {
- case SDLA_INTR_RX:
- sdla_receive(dev);
- break;
-
- /* the command will get an error return, which is processed above */
- case SDLA_INTR_MODEM:
- case SDLA_INTR_STATUS:
- sdla_cmd(dev, SDLA_READ_DLC_STATUS, 0, 0, NULL, 0, NULL, NULL);
- break;
-
- case SDLA_INTR_TX:
- case SDLA_INTR_COMPLETE:
- case SDLA_INTR_TIMER:
- netdev_warn(dev, "invalid irq flag 0x%02X\n", byte);
- break;
- }
-
- /* the S502E requires a manual acknowledgement of the interrupt */
- if (flp->type == SDLA_S502E)
- {
- flp->state &= ~SDLA_S502E_INTACK;
- outb(flp->state, dev->base_addr + SDLA_REG_CONTROL);
- flp->state |= SDLA_S502E_INTACK;
- outb(flp->state, dev->base_addr + SDLA_REG_CONTROL);
- }
-
- /* this clears the byte, informing the Z80 we're done */
- byte = 0;
- sdla_write(dev, flp->type == SDLA_S508 ? SDLA_508_IRQ_INTERFACE : SDLA_502_IRQ_INTERFACE, &byte, sizeof(byte));
- return IRQ_HANDLED;
-}
-
-static void sdla_poll(struct timer_list *t)
-{
- struct frad_local *flp = from_timer(flp, t, timer);
- struct net_device *dev = flp->dev;
-
- if (sdla_byte(dev, SDLA_502_RCV_BUF))
- sdla_receive(dev);
-
- flp->timer.expires = 1;
- add_timer(&flp->timer);
-}
-
-static int sdla_close(struct net_device *dev)
-{
- struct frad_local *flp;
- struct intr_info intr;
- int len, i;
- short dlcis[CONFIG_DLCI_MAX];
-
- flp = netdev_priv(dev);
-
- len = 0;
- for(i=0;i<CONFIG_DLCI_MAX;i++)
- if (flp->dlci[i])
- dlcis[len++] = abs(flp->dlci[i]);
- len *= 2;
-
- if (flp->config.station == FRAD_STATION_NODE)
- {
- for(i=0;i<CONFIG_DLCI_MAX;i++)
- if (flp->dlci[i] > 0)
- sdla_cmd(dev, SDLA_DEACTIVATE_DLCI, 0, 0, dlcis, len, NULL, NULL);
- sdla_cmd(dev, SDLA_DELETE_DLCI, 0, 0, &flp->dlci[i], sizeof(flp->dlci[i]), NULL, NULL);
- }
-
- memset(&intr, 0, sizeof(intr));
- /* let's start up the reception */
- switch(flp->type)
- {
- case SDLA_S502A:
- del_timer(&flp->timer);
- break;
-
- case SDLA_S502E:
- sdla_cmd(dev, SDLA_SET_IRQ_TRIGGER, 0, 0, &intr, sizeof(char) + sizeof(short), NULL, NULL);
- flp->state &= ~SDLA_S502E_INTACK;
- outb(flp->state, dev->base_addr + SDLA_REG_CONTROL);
- break;
-
- case SDLA_S507:
- break;
-
- case SDLA_S508:
- sdla_cmd(dev, SDLA_SET_IRQ_TRIGGER, 0, 0, &intr, sizeof(struct intr_info), NULL, NULL);
- flp->state &= ~SDLA_S508_INTEN;
- outb(flp->state, dev->base_addr + SDLA_REG_CONTROL);
- break;
- }
-
- sdla_cmd(dev, SDLA_DISABLE_COMMUNICATIONS, 0, 0, NULL, 0, NULL, NULL);
-
- netif_stop_queue(dev);
-
- return 0;
-}
-
-struct conf_data {
- struct frad_conf config;
- short dlci[CONFIG_DLCI_MAX];
-};
-
-static int sdla_open(struct net_device *dev)
-{
- struct frad_local *flp;
- struct dlci_local *dlp;
- struct conf_data data;
- struct intr_info intr;
- int len, i;
- char byte;
-
- flp = netdev_priv(dev);
-
- if (!flp->initialized)
- return -EPERM;
-
- if (!flp->configured)
- return -EPERM;
-
- /* time to send in the configuration */
- len = 0;
- for(i=0;i<CONFIG_DLCI_MAX;i++)
- if (flp->dlci[i])
- data.dlci[len++] = abs(flp->dlci[i]);
- len *= 2;
-
- memcpy(&data.config, &flp->config, sizeof(struct frad_conf));
- len += sizeof(struct frad_conf);
-
- sdla_cmd(dev, SDLA_DISABLE_COMMUNICATIONS, 0, 0, NULL, 0, NULL, NULL);
- sdla_cmd(dev, SDLA_SET_DLCI_CONFIGURATION, 0, 0, &data, len, NULL, NULL);
-
- if (flp->type == SDLA_S508)
- flp->buffer = 0;
-
- sdla_cmd(dev, SDLA_ENABLE_COMMUNICATIONS, 0, 0, NULL, 0, NULL, NULL);
-
- /* let's start up the reception */
- memset(&intr, 0, sizeof(intr));
- switch(flp->type)
- {
- case SDLA_S502A:
- flp->timer.expires = 1;
- add_timer(&flp->timer);
- break;
-
- case SDLA_S502E:
- flp->state |= SDLA_S502E_ENABLE;
- outb(flp->state, dev->base_addr + SDLA_REG_CONTROL);
- flp->state |= SDLA_S502E_INTACK;
- outb(flp->state, dev->base_addr + SDLA_REG_CONTROL);
- byte = 0;
- sdla_write(dev, SDLA_502_IRQ_INTERFACE, &byte, sizeof(byte));
- intr.flags = SDLA_INTR_RX | SDLA_INTR_STATUS | SDLA_INTR_MODEM;
- sdla_cmd(dev, SDLA_SET_IRQ_TRIGGER, 0, 0, &intr, sizeof(char) + sizeof(short), NULL, NULL);
- break;
-
- case SDLA_S507:
- break;
-
- case SDLA_S508:
- flp->state |= SDLA_S508_INTEN;
- outb(flp->state, dev->base_addr + SDLA_REG_CONTROL);
- byte = 0;
- sdla_write(dev, SDLA_508_IRQ_INTERFACE, &byte, sizeof(byte));
- intr.flags = SDLA_INTR_RX | SDLA_INTR_STATUS | SDLA_INTR_MODEM;
- intr.irq = dev->irq;
- sdla_cmd(dev, SDLA_SET_IRQ_TRIGGER, 0, 0, &intr, sizeof(struct intr_info), NULL, NULL);
- break;
- }
-
- if (flp->config.station == FRAD_STATION_CPE)
- {
- byte = SDLA_ICS_STATUS_ENQ;
- sdla_cmd(dev, SDLA_ISSUE_IN_CHANNEL_SIGNAL, 0, 0, &byte, sizeof(byte), NULL, NULL);
- }
- else
- {
- sdla_cmd(dev, SDLA_ADD_DLCI, 0, 0, data.dlci, len - sizeof(struct frad_conf), NULL, NULL);
- for(i=0;i<CONFIG_DLCI_MAX;i++)
- if (flp->dlci[i] > 0)
- sdla_cmd(dev, SDLA_ACTIVATE_DLCI, 0, 0, &flp->dlci[i], 2*sizeof(flp->dlci[i]), NULL, NULL);
- }
-
- /* configure any specific DLCI settings */
- for(i=0;i<CONFIG_DLCI_MAX;i++)
- if (flp->dlci[i])
- {
- dlp = netdev_priv(flp->master[i]);
- if (dlp->configured)
- sdla_cmd(dev, SDLA_SET_DLCI_CONFIGURATION, abs(flp->dlci[i]), 0, &dlp->config, sizeof(struct dlci_conf), NULL, NULL);
- }
-
- netif_start_queue(dev);
-
- return 0;
-}
-
-static int sdla_config(struct net_device *dev, struct frad_conf __user *conf, int get)
-{
- struct frad_local *flp;
- struct conf_data data;
- int i;
- short size;
-
- if (dev->type == 0xFFFF)
- return -EUNATCH;
-
- flp = netdev_priv(dev);
-
- if (!get)
- {
- if (netif_running(dev))
- return -EBUSY;
-
- if(copy_from_user(&data.config, conf, sizeof(struct frad_conf)))
- return -EFAULT;
-
- if (data.config.station & ~FRAD_STATION_NODE)
- return -EINVAL;
-
- if (data.config.flags & ~FRAD_VALID_FLAGS)
- return -EINVAL;
-
- if ((data.config.kbaud < 0) ||
- ((data.config.kbaud > 128) && (flp->type != SDLA_S508)))
- return -EINVAL;
-
- if (data.config.clocking & ~(FRAD_CLOCK_INT | SDLA_S508_PORT_RS232))
- return -EINVAL;
-
- if ((data.config.mtu < 0) || (data.config.mtu > SDLA_MAX_MTU))
- return -EINVAL;
-
- if ((data.config.T391 < 5) || (data.config.T391 > 30))
- return -EINVAL;
-
- if ((data.config.T392 < 5) || (data.config.T392 > 30))
- return -EINVAL;
-
- if ((data.config.N391 < 1) || (data.config.N391 > 255))
- return -EINVAL;
-
- if ((data.config.N392 < 1) || (data.config.N392 > 10))
- return -EINVAL;
-
- if ((data.config.N393 < 1) || (data.config.N393 > 10))
- return -EINVAL;
-
- memcpy(&flp->config, &data.config, sizeof(struct frad_conf));
- flp->config.flags |= SDLA_DIRECT_RECV;
-
- if (flp->type == SDLA_S508)
- flp->config.flags |= SDLA_TX70_RX30;
-
- if (dev->mtu != flp->config.mtu)
- {
- /* this is required to change the MTU */
- dev->mtu = flp->config.mtu;
- for(i=0;i<CONFIG_DLCI_MAX;i++)
- if (flp->master[i])
- flp->master[i]->mtu = flp->config.mtu;
- }
-
- flp->config.mtu += sizeof(struct frhdr);
-
- /* off to the races! */
- if (!flp->configured)
- sdla_start(dev);
-
- flp->configured = 1;
- }
- else
- {
- /* no sense reading if the CPU isn't started */
- if (netif_running(dev))
- {
- size = sizeof(data);
- if (sdla_cmd(dev, SDLA_READ_DLCI_CONFIGURATION, 0, 0, NULL, 0, &data, &size) != SDLA_RET_OK)
- return -EIO;
- }
- else
- if (flp->configured)
- memcpy(&data.config, &flp->config, sizeof(struct frad_conf));
- else
- memset(&data.config, 0, sizeof(struct frad_conf));
-
- memcpy(&flp->config, &data.config, sizeof(struct frad_conf));
- data.config.flags &= FRAD_VALID_FLAGS;
- data.config.mtu -= data.config.mtu > sizeof(struct frhdr) ? sizeof(struct frhdr) : data.config.mtu;
- return copy_to_user(conf, &data.config, sizeof(struct frad_conf))?-EFAULT:0;
- }
-
- return 0;
-}
-
-static int sdla_xfer(struct net_device *dev, struct sdla_mem __user *info, int read)
-{
- struct sdla_mem mem;
- char *temp;
-
- if(copy_from_user(&mem, info, sizeof(mem)))
- return -EFAULT;
-
- if (read)
- {
- temp = kzalloc(mem.len, GFP_KERNEL);
- if (!temp)
- return -ENOMEM;
- sdla_read(dev, mem.addr, temp, mem.len);
- if(copy_to_user(mem.data, temp, mem.len))
- {
- kfree(temp);
- return -EFAULT;
- }
- kfree(temp);
- }
- else
- {
- temp = memdup_user(mem.data, mem.len);
- if (IS_ERR(temp))
- return PTR_ERR(temp);
- sdla_write(dev, mem.addr, temp, mem.len);
- kfree(temp);
- }
- return 0;
-}
-
-static int sdla_reconfig(struct net_device *dev)
-{
- struct frad_local *flp;
- struct conf_data data;
- int i, len;
-
- flp = netdev_priv(dev);
-
- len = 0;
- for(i=0;i<CONFIG_DLCI_MAX;i++)
- if (flp->dlci[i])
- data.dlci[len++] = flp->dlci[i];
- len *= 2;
-
- memcpy(&data, &flp->config, sizeof(struct frad_conf));
- len += sizeof(struct frad_conf);
-
- sdla_cmd(dev, SDLA_DISABLE_COMMUNICATIONS, 0, 0, NULL, 0, NULL, NULL);
- sdla_cmd(dev, SDLA_SET_DLCI_CONFIGURATION, 0, 0, &data, len, NULL, NULL);
- sdla_cmd(dev, SDLA_ENABLE_COMMUNICATIONS, 0, 0, NULL, 0, NULL, NULL);
-
- return 0;
-}
-
-static int sdla_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
-{
- struct frad_local *flp;
-
- if(!capable(CAP_NET_ADMIN))
- return -EPERM;
-
- flp = netdev_priv(dev);
-
- if (!flp->initialized)
- return -EINVAL;
-
- switch (cmd)
- {
- case FRAD_GET_CONF:
- case FRAD_SET_CONF:
- return sdla_config(dev, ifr->ifr_data, cmd == FRAD_GET_CONF);
-
- case SDLA_IDENTIFY:
- ifr->ifr_flags = flp->type;
- break;
-
- case SDLA_CPUSPEED:
- return sdla_cpuspeed(dev, ifr);
-
-/* ==========================================================
-NOTE: This is rather a useless action right now, as the
- current driver does not support protocols other than
- FR. However, Sangoma has modules for a number of
- other protocols in the works.
-============================================================*/
- case SDLA_PROTOCOL:
- if (flp->configured)
- return -EALREADY;
-
- switch (ifr->ifr_flags)
- {
- case ARPHRD_FRAD:
- dev->type = ifr->ifr_flags;
- break;
- default:
- return -ENOPROTOOPT;
- }
- break;
-
- case SDLA_CLEARMEM:
- sdla_clear(dev);
- break;
-
- case SDLA_WRITEMEM:
- case SDLA_READMEM:
- if(!capable(CAP_SYS_RAWIO))
- return -EPERM;
- return sdla_xfer(dev, ifr->ifr_data, cmd == SDLA_READMEM);
-
- case SDLA_START:
- sdla_start(dev);
- break;
-
- case SDLA_STOP:
- sdla_stop(dev);
- break;
-
- default:
- return -EOPNOTSUPP;
- }
- return 0;
-}
-
-static int sdla_change_mtu(struct net_device *dev, int new_mtu)
-{
- if (netif_running(dev))
- return -EBUSY;
-
- /* for now, you can't change the MTU! */
- return -EOPNOTSUPP;
-}
-
-static int sdla_set_config(struct net_device *dev, struct ifmap *map)
-{
- struct frad_local *flp;
- int i;
- char byte;
- unsigned base;
- int err = -EINVAL;
-
- flp = netdev_priv(dev);
-
- if (flp->initialized)
- return -EINVAL;
-
- for(i=0; i < ARRAY_SIZE(valid_port); i++)
- if (valid_port[i] == map->base_addr)
- break;
-
- if (i == ARRAY_SIZE(valid_port))
- return -EINVAL;
-
- if (!request_region(map->base_addr, SDLA_IO_EXTENTS, dev->name)){
- pr_warn("io-port 0x%04lx in use\n", dev->base_addr);
- return -EINVAL;
- }
- base = map->base_addr;
-
- /* test for card types, S502A, S502E, S507, S508 */
- /* these tests shut down the card completely, so clear the state */
- flp->type = SDLA_UNKNOWN;
- flp->state = 0;
-
- for(i=1;i<SDLA_IO_EXTENTS;i++)
- if (inb(base + i) != 0xFF)
- break;
-
- if (i == SDLA_IO_EXTENTS) {
- outb(SDLA_HALT, base + SDLA_REG_Z80_CONTROL);
- if ((inb(base + SDLA_S502_STS) & 0x0F) == 0x08) {
- outb(SDLA_S502E_INTACK, base + SDLA_REG_CONTROL);
- if ((inb(base + SDLA_S502_STS) & 0x0F) == 0x0C) {
- outb(SDLA_HALT, base + SDLA_REG_CONTROL);
- flp->type = SDLA_S502E;
- goto got_type;
- }
- }
- }
-
- for(byte=inb(base),i=0;i<SDLA_IO_EXTENTS;i++)
- if (inb(base + i) != byte)
- break;
-
- if (i == SDLA_IO_EXTENTS) {
- outb(SDLA_HALT, base + SDLA_REG_CONTROL);
- if ((inb(base + SDLA_S502_STS) & 0x7E) == 0x30) {
- outb(SDLA_S507_ENABLE, base + SDLA_REG_CONTROL);
- if ((inb(base + SDLA_S502_STS) & 0x7E) == 0x32) {
- outb(SDLA_HALT, base + SDLA_REG_CONTROL);
- flp->type = SDLA_S507;
- goto got_type;
- }
- }
- }
-
- outb(SDLA_HALT, base + SDLA_REG_CONTROL);
- if ((inb(base + SDLA_S508_STS) & 0x3F) == 0x00) {
- outb(SDLA_S508_INTEN, base + SDLA_REG_CONTROL);
- if ((inb(base + SDLA_S508_STS) & 0x3F) == 0x10) {
- outb(SDLA_HALT, base + SDLA_REG_CONTROL);
- flp->type = SDLA_S508;
- goto got_type;
- }
- }
-
- outb(SDLA_S502A_HALT, base + SDLA_REG_CONTROL);
- if (inb(base + SDLA_S502_STS) == 0x40) {
- outb(SDLA_S502A_START, base + SDLA_REG_CONTROL);
- if (inb(base + SDLA_S502_STS) == 0x40) {
- outb(SDLA_S502A_INTEN, base + SDLA_REG_CONTROL);
- if (inb(base + SDLA_S502_STS) == 0x44) {
- outb(SDLA_S502A_START, base + SDLA_REG_CONTROL);
- flp->type = SDLA_S502A;
- goto got_type;
- }
- }
- }
-
- netdev_notice(dev, "Unknown card type\n");
- err = -ENODEV;
- goto fail;
-
-got_type:
- switch(base) {
- case 0x270:
- case 0x280:
- case 0x380:
- case 0x390:
- if (flp->type != SDLA_S508 && flp->type != SDLA_S507)
- goto fail;
- }
-
- switch (map->irq) {
- case 2:
- if (flp->type != SDLA_S502E)
- goto fail;
- break;
-
- case 10:
- case 11:
- case 12:
- case 15:
- case 4:
- if (flp->type != SDLA_S508 && flp->type != SDLA_S507)
- goto fail;
- break;
- case 3:
- case 5:
- case 7:
- if (flp->type == SDLA_S502A)
- goto fail;
- break;
-
- default:
- goto fail;
- }
-
- err = -EAGAIN;
- if (request_irq(dev->irq, sdla_isr, 0, dev->name, dev))
- goto fail;
-
- if (flp->type == SDLA_S507) {
- switch(dev->irq) {
- case 3:
- flp->state = SDLA_S507_IRQ3;
- break;
- case 4:
- flp->state = SDLA_S507_IRQ4;
- break;
- case 5:
- flp->state = SDLA_S507_IRQ5;
- break;
- case 7:
- flp->state = SDLA_S507_IRQ7;
- break;
- case 10:
- flp->state = SDLA_S507_IRQ10;
- break;
- case 11:
- flp->state = SDLA_S507_IRQ11;
- break;
- case 12:
- flp->state = SDLA_S507_IRQ12;
- break;
- case 15:
- flp->state = SDLA_S507_IRQ15;
- break;
- }
- }
-
- for(i=0; i < ARRAY_SIZE(valid_mem); i++)
- if (valid_mem[i] == map->mem_start)
- break;
-
- err = -EINVAL;
- if (i == ARRAY_SIZE(valid_mem))
- goto fail2;
-
- if (flp->type == SDLA_S502A && (map->mem_start & 0xF000) >> 12 == 0x0E)
- goto fail2;
-
- if (flp->type != SDLA_S507 && map->mem_start >> 16 == 0x0B)
- goto fail2;
-
- if (flp->type == SDLA_S507 && map->mem_start >> 16 == 0x0D)
- goto fail2;
-
- byte = flp->type != SDLA_S508 ? SDLA_8K_WINDOW : 0;
- byte |= (map->mem_start & 0xF000) >> (12 + (flp->type == SDLA_S508 ? 1 : 0));
- switch(flp->type) {
- case SDLA_S502A:
- case SDLA_S502E:
- switch (map->mem_start >> 16) {
- case 0x0A:
- byte |= SDLA_S502_SEG_A;
- break;
- case 0x0C:
- byte |= SDLA_S502_SEG_C;
- break;
- case 0x0D:
- byte |= SDLA_S502_SEG_D;
- break;
- case 0x0E:
- byte |= SDLA_S502_SEG_E;
- break;
- }
- break;
- case SDLA_S507:
- switch (map->mem_start >> 16) {
- case 0x0A:
- byte |= SDLA_S507_SEG_A;
- break;
- case 0x0B:
- byte |= SDLA_S507_SEG_B;
- break;
- case 0x0C:
- byte |= SDLA_S507_SEG_C;
- break;
- case 0x0E:
- byte |= SDLA_S507_SEG_E;
- break;
- }
- break;
- case SDLA_S508:
- switch (map->mem_start >> 16) {
- case 0x0A:
- byte |= SDLA_S508_SEG_A;
- break;
- case 0x0C:
- byte |= SDLA_S508_SEG_C;
- break;
- case 0x0D:
- byte |= SDLA_S508_SEG_D;
- break;
- case 0x0E:
- byte |= SDLA_S508_SEG_E;
- break;
- }
- break;
- }
-
- /* set the memory bits, and enable access */
- outb(byte, base + SDLA_REG_PC_WINDOW);
-
- switch(flp->type)
- {
- case SDLA_S502E:
- flp->state = SDLA_S502E_ENABLE;
- break;
- case SDLA_S507:
- flp->state |= SDLA_MEMEN;
- break;
- case SDLA_S508:
- flp->state = SDLA_MEMEN;
- break;
- }
- outb(flp->state, base + SDLA_REG_CONTROL);
-
- dev->irq = map->irq;
- dev->base_addr = base;
- dev->mem_start = map->mem_start;
- dev->mem_end = dev->mem_start + 0x2000;
- flp->initialized = 1;
- return 0;
-
-fail2:
- free_irq(map->irq, dev);
-fail:
- release_region(base, SDLA_IO_EXTENTS);
- return err;
-}
-
-static const struct net_device_ops sdla_netdev_ops = {
- .ndo_open = sdla_open,
- .ndo_stop = sdla_close,
- .ndo_do_ioctl = sdla_ioctl,
- .ndo_set_config = sdla_set_config,
- .ndo_start_xmit = sdla_transmit,
- .ndo_change_mtu = sdla_change_mtu,
-};
-
-static void setup_sdla(struct net_device *dev)
-{
- struct frad_local *flp = netdev_priv(dev);
-
- netdev_boot_setup_check(dev);
-
- dev->netdev_ops = &sdla_netdev_ops;
- dev->flags = 0;
- dev->type = 0xFFFF;
- dev->hard_header_len = 0;
- dev->addr_len = 0;
- dev->mtu = SDLA_MAX_MTU;
-
- flp->activate = sdla_activate;
- flp->deactivate = sdla_deactivate;
- flp->assoc = sdla_assoc;
- flp->deassoc = sdla_deassoc;
- flp->dlci_conf = sdla_dlci_conf;
- flp->dev = dev;
-
- timer_setup(&flp->timer, sdla_poll, 0);
- flp->timer.expires = 1;
-}
-
-static struct net_device *sdla;
-
-static int __init init_sdla(void)
-{
- int err;
-
- printk("%s.\n", version);
-
- sdla = alloc_netdev(sizeof(struct frad_local), "sdla0",
- NET_NAME_UNKNOWN, setup_sdla);
- if (!sdla)
- return -ENOMEM;
-
- err = register_netdev(sdla);
- if (err)
- free_netdev(sdla);
-
- return err;
-}
-
-static void __exit exit_sdla(void)
-{
- struct frad_local *flp = netdev_priv(sdla);
-
- unregister_netdev(sdla);
- if (flp->initialized) {
- free_irq(sdla->irq, sdla);
- release_region(sdla->base_addr, SDLA_IO_EXTENTS);
- }
- del_timer_sync(&flp->timer);
- free_netdev(sdla);
-}
-
-MODULE_LICENSE("GPL");
-
-module_init(init_sdla);
-module_exit(exit_sdla);
@@ -205,7 +205,6 @@ header-test- += linux/i3c/master.h
header-test- += linux/i8042.h
header-test- += linux/ide.h
header-test- += linux/idle_inject.h
-header-test- += linux/if_frad.h
header-test- += linux/if_rmnet.h
header-test- += linux/if_tap.h
header-test- += linux/iio/accel/kxcjk_1013.h
deleted file mode 100644
@@ -1,92 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * DLCI/FRAD Definitions for Frame Relay Access Devices. DLCI devices are
- * created for each DLCI associated with a FRAD. The FRAD driver
- * is not truly a network device, but the lower level device
- * handler. This allows other FRAD manufacturers to use the DLCI
- * code, including its RFC1490 encapsulation alongside the current
- * implementation for the Sangoma cards.
- *
- * Version: @(#)if_ifrad.h 0.15 31 Mar 96
- *
- * Author: Mike McLagan <mike.mclagan@linux.org>
- *
- * Changes:
- * 0.15 Mike McLagan changed structure defs (packed)
- * re-arranged flags
- * added DLCI_RET vars
- */
-#ifndef _FRAD_H_
-#define _FRAD_H_
-
-#include <uapi/linux/if_frad.h>
-
-
-#if defined(CONFIG_DLCI) || defined(CONFIG_DLCI_MODULE)
-
-/* these are the fields of an RFC 1490 header */
-struct frhdr
-{
- unsigned char control;
-
- /* for IP packets, this can be the NLPID */
- unsigned char pad;
-
- unsigned char NLPID;
- unsigned char OUI[3];
- __be16 PID;
-
-#define IP_NLPID pad
-} __packed;
-
-/* see RFC 1490 for the definition of the following */
-#define FRAD_I_UI 0x03
-
-#define FRAD_P_PADDING 0x00
-#define FRAD_P_Q933 0x08
-#define FRAD_P_SNAP 0x80
-#define FRAD_P_CLNP 0x81
-#define FRAD_P_IP 0xCC
-
-struct dlci_local
-{
- struct net_device *master;
- struct net_device *slave;
- struct dlci_conf config;
- int configured;
- struct list_head list;
-
- /* callback function */
- void (*receive)(struct sk_buff *skb, struct net_device *);
-};
-
-struct frad_local
-{
- /* devices which this FRAD is slaved to */
- struct net_device *master[CONFIG_DLCI_MAX];
- short dlci[CONFIG_DLCI_MAX];
-
- struct frad_conf config;
- int configured; /* has this device been configured */
- int initialized; /* mem_start, port, irq set ? */
-
- /* callback functions */
- int (*activate)(struct net_device *, struct net_device *);
- int (*deactivate)(struct net_device *, struct net_device *);
- int (*assoc)(struct net_device *, struct net_device *);
- int (*deassoc)(struct net_device *, struct net_device *);
- int (*dlci_conf)(struct net_device *, struct net_device *, int get);
-
- /* fields that are used by the Sangoma SDLA cards */
- struct timer_list timer;
- struct net_device *dev;
- int type; /* adapter type */
- int state; /* state of the S502/8 control latch */
- int buffer; /* current buffer for S508 firmware */
-};
-
-#endif /* CONFIG_DLCI || CONFIG_DLCI_MODULE */
-
-extern void dlci_ioctl_set(int (*hook)(unsigned int, void __user *));
-
-#endif
deleted file mode 100644
@@ -1,240 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * INET An implementation of the TCP/IP protocol suite for the LINUX
- * operating system. INET is implemented using the BSD Socket
- * interface as the means of communication with the user level.
- *
- * Global definitions for the Frame relay interface.
- *
- * Version: @(#)if_ifrad.h 0.20 13 Apr 96
- *
- * Author: Mike McLagan <mike.mclagan@linux.org>
- *
- * Changes:
- * 0.15 Mike McLagan Structure packing
- *
- * 0.20 Mike McLagan New flags for S508 buffer handling
- */
-#ifndef SDLA_H
-#define SDLA_H
-
-#include <uapi/linux/sdla.h>
-
-
-/* important Z80 window addresses */
-#define SDLA_CONTROL_WND 0xE000
-
-#define SDLA_502_CMD_BUF 0xEF60
-#define SDLA_502_RCV_BUF 0xA900
-#define SDLA_502_TXN_AVAIL 0xFFF1
-#define SDLA_502_RCV_AVAIL 0xFFF2
-#define SDLA_502_EVENT_FLAGS 0xFFF3
-#define SDLA_502_MDM_STATUS 0xFFF4
-#define SDLA_502_IRQ_INTERFACE 0xFFFD
-#define SDLA_502_IRQ_PERMISSION 0xFFFE
-#define SDLA_502_DATA_OFS 0x0010
-
-#define SDLA_508_CMD_BUF 0xE000
-#define SDLA_508_TXBUF_INFO 0xF100
-#define SDLA_508_RXBUF_INFO 0xF120
-#define SDLA_508_EVENT_FLAGS 0xF003
-#define SDLA_508_MDM_STATUS 0xF004
-#define SDLA_508_IRQ_INTERFACE 0xF010
-#define SDLA_508_IRQ_PERMISSION 0xF011
-#define SDLA_508_TSE_OFFSET 0xF012
-
-/* Event flags */
-#define SDLA_EVENT_STATUS 0x01
-#define SDLA_EVENT_DLCI_STATUS 0x02
-#define SDLA_EVENT_BAD_DLCI 0x04
-#define SDLA_EVENT_LINK_DOWN 0x40
-
-/* IRQ Trigger flags */
-#define SDLA_INTR_RX 0x01
-#define SDLA_INTR_TX 0x02
-#define SDLA_INTR_MODEM 0x04
-#define SDLA_INTR_COMPLETE 0x08
-#define SDLA_INTR_STATUS 0x10
-#define SDLA_INTR_TIMER 0x20
-
-/* DLCI status bits */
-#define SDLA_DLCI_DELETED 0x01
-#define SDLA_DLCI_ACTIVE 0x02
-#define SDLA_DLCI_WAITING 0x04
-#define SDLA_DLCI_NEW 0x08
-#define SDLA_DLCI_INCLUDED 0x40
-
-/* valid command codes */
-#define SDLA_INFORMATION_WRITE 0x01
-#define SDLA_INFORMATION_READ 0x02
-#define SDLA_ISSUE_IN_CHANNEL_SIGNAL 0x03
-#define SDLA_SET_DLCI_CONFIGURATION 0x10
-#define SDLA_READ_DLCI_CONFIGURATION 0x11
-#define SDLA_DISABLE_COMMUNICATIONS 0x12
-#define SDLA_ENABLE_COMMUNICATIONS 0x13
-#define SDLA_READ_DLC_STATUS 0x14
-#define SDLA_READ_DLC_STATISTICS 0x15
-#define SDLA_FLUSH_DLC_STATISTICS 0x16
-#define SDLA_LIST_ACTIVE_DLCI 0x17
-#define SDLA_FLUSH_INFORMATION_BUFFERS 0x18
-#define SDLA_ADD_DLCI 0x20
-#define SDLA_DELETE_DLCI 0x21
-#define SDLA_ACTIVATE_DLCI 0x22
-#define SDLA_DEACTIVATE_DLCI 0x23
-#define SDLA_READ_MODEM_STATUS 0x30
-#define SDLA_SET_MODEM_STATUS 0x31
-#define SDLA_READ_COMMS_ERR_STATS 0x32
-#define SDLA_FLUSH_COMMS_ERR_STATS 0x33
-#define SDLA_READ_CODE_VERSION 0x40
-#define SDLA_SET_IRQ_TRIGGER 0x50
-#define SDLA_GET_IRQ_TRIGGER 0x51
-
-/* In channel signal types */
-#define SDLA_ICS_LINK_VERIFY 0x02
-#define SDLA_ICS_STATUS_ENQ 0x03
-
-/* modem status flags */
-#define SDLA_MODEM_DTR_HIGH 0x01
-#define SDLA_MODEM_RTS_HIGH 0x02
-#define SDLA_MODEM_DCD_HIGH 0x08
-#define SDLA_MODEM_CTS_HIGH 0x20
-
-/* used for RET_MODEM interpretation */
-#define SDLA_MODEM_DCD_LOW 0x01
-#define SDLA_MODEM_CTS_LOW 0x02
-
-/* return codes */
-#define SDLA_RET_OK 0x00
-#define SDLA_RET_COMMUNICATIONS 0x01
-#define SDLA_RET_CHANNEL_INACTIVE 0x02
-#define SDLA_RET_DLCI_INACTIVE 0x03
-#define SDLA_RET_DLCI_CONFIG 0x04
-#define SDLA_RET_BUF_TOO_BIG 0x05
-#define SDLA_RET_NO_DATA 0x05
-#define SDLA_RET_BUF_OVERSIZE 0x06
-#define SDLA_RET_CIR_OVERFLOW 0x07
-#define SDLA_RET_NO_BUFS 0x08
-#define SDLA_RET_TIMEOUT 0x0A
-#define SDLA_RET_MODEM 0x10
-#define SDLA_RET_CHANNEL_OFF 0x11
-#define SDLA_RET_CHANNEL_ON 0x12
-#define SDLA_RET_DLCI_STATUS 0x13
-#define SDLA_RET_DLCI_UNKNOWN 0x14
-#define SDLA_RET_COMMAND_INVALID 0x1F
-
-/* Configuration flags */
-#define SDLA_DIRECT_RECV 0x0080
-#define SDLA_TX_NO_EXCEPT 0x0020
-#define SDLA_NO_ICF_MSGS 0x1000
-#define SDLA_TX50_RX50 0x0000
-#define SDLA_TX70_RX30 0x2000
-#define SDLA_TX30_RX70 0x4000
-
-/* IRQ selection flags */
-#define SDLA_IRQ_RECEIVE 0x01
-#define SDLA_IRQ_TRANSMIT 0x02
-#define SDLA_IRQ_MODEM_STAT 0x04
-#define SDLA_IRQ_COMMAND 0x08
-#define SDLA_IRQ_CHANNEL 0x10
-#define SDLA_IRQ_TIMER 0x20
-
-/* definitions for PC memory mapping */
-#define SDLA_8K_WINDOW 0x01
-#define SDLA_S502_SEG_A 0x10
-#define SDLA_S502_SEG_C 0x20
-#define SDLA_S502_SEG_D 0x00
-#define SDLA_S502_SEG_E 0x30
-#define SDLA_S507_SEG_A 0x00
-#define SDLA_S507_SEG_B 0x40
-#define SDLA_S507_SEG_C 0x80
-#define SDLA_S507_SEG_E 0xC0
-#define SDLA_S508_SEG_A 0x00
-#define SDLA_S508_SEG_C 0x10
-#define SDLA_S508_SEG_D 0x08
-#define SDLA_S508_SEG_E 0x18
-
-/* SDLA adapter port constants */
-#define SDLA_IO_EXTENTS 0x04
-
-#define SDLA_REG_CONTROL 0x00
-#define SDLA_REG_PC_WINDOW 0x01 /* offset for PC window select latch */
-#define SDLA_REG_Z80_WINDOW 0x02 /* offset for Z80 window select latch */
-#define SDLA_REG_Z80_CONTROL 0x03 /* offset for Z80 control latch */
-
-#define SDLA_S502_STS 0x00 /* status reg for 502, 502E, 507 */
-#define SDLA_S508_GNRL 0x00 /* general purp. reg for 508 */
-#define SDLA_S508_STS 0x01 /* status reg for 508 */
-#define SDLA_S508_IDR 0x02 /* ID reg for 508 */
-
-/* control register flags */
-#define SDLA_S502A_START 0x00 /* start the CPU */
-#define SDLA_S502A_INTREQ 0x02
-#define SDLA_S502A_INTEN 0x04
-#define SDLA_S502A_HALT 0x08 /* halt the CPU */
-#define SDLA_S502A_NMI 0x10 /* issue an NMI to the CPU */
-
-#define SDLA_S502E_CPUEN 0x01
-#define SDLA_S502E_ENABLE 0x02
-#define SDLA_S502E_INTACK 0x04
-
-#define SDLA_S507_ENABLE 0x01
-#define SDLA_S507_IRQ3 0x00
-#define SDLA_S507_IRQ4 0x20
-#define SDLA_S507_IRQ5 0x40
-#define SDLA_S507_IRQ7 0x60
-#define SDLA_S507_IRQ10 0x80
-#define SDLA_S507_IRQ11 0xA0
-#define SDLA_S507_IRQ12 0xC0
-#define SDLA_S507_IRQ15 0xE0
-
-#define SDLA_HALT 0x00
-#define SDLA_CPUEN 0x02
-#define SDLA_MEMEN 0x04
-#define SDLA_S507_EPROMWR 0x08
-#define SDLA_S507_EPROMCLK 0x10
-#define SDLA_S508_INTRQ 0x08
-#define SDLA_S508_INTEN 0x10
-
-struct sdla_cmd {
- char opp_flag;
- char cmd;
- short length;
- char retval;
- short dlci;
- char flags;
- short rxlost_int;
- long rxlost_app;
- char reserve[2];
- char data[SDLA_MAX_DATA]; /* transfer data buffer */
-} __attribute__((packed));
-
-struct intr_info {
- char flags;
- short txlen;
- char irq;
- char flags2;
- short timeout;
-} __attribute__((packed));
-
-/* found in the 508's control window at RXBUF_INFO */
-struct buf_info {
- unsigned short rse_num;
- unsigned long rse_base;
- unsigned long rse_next;
- unsigned long buf_base;
- unsigned short reserved;
- unsigned long buf_top;
-} __attribute__((packed));
-
-/* structure pointed to by rse_base in RXBUF_INFO struct */
-struct buf_entry {
- char opp_flag;
- short length;
- short dlci;
- char flags;
- short timestamp;
- short reserved[2];
- long buf_addr;
-} __attribute__((packed));
-
-#endif
deleted file mode 100644
@@ -1,123 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ WITH Linux-syscall-note */
-/*
- * DLCI/FRAD Definitions for Frame Relay Access Devices. DLCI devices are
- * created for each DLCI associated with a FRAD. The FRAD driver
- * is not truly a network device, but the lower level device
- * handler. This allows other FRAD manufacturers to use the DLCI
- * code, including its RFC1490 encapsulation alongside the current
- * implementation for the Sangoma cards.
- *
- * Version: @(#)if_ifrad.h 0.15 31 Mar 96
- *
- * Author: Mike McLagan <mike.mclagan@linux.org>
- *
- * Changes:
- * 0.15 Mike McLagan changed structure defs (packed)
- * re-arranged flags
- * added DLCI_RET vars
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#ifndef _UAPI_FRAD_H_
-#define _UAPI_FRAD_H_
-
-#include <linux/if.h>
-
-/* Structures and constants associated with the DLCI device driver */
-
-struct dlci_add
-{
- char devname[IFNAMSIZ];
- short dlci;
-};
-
-#define DLCI_GET_CONF (SIOCDEVPRIVATE + 2)
-#define DLCI_SET_CONF (SIOCDEVPRIVATE + 3)
-
-/*
- * These are related to the Sangoma SDLA and should remain in order.
- * Code within the SDLA module is based on the specifics of this
- * structure. Change at your own peril.
- */
-struct dlci_conf {
- short flags;
- short CIR_fwd;
- short Bc_fwd;
- short Be_fwd;
- short CIR_bwd;
- short Bc_bwd;
- short Be_bwd;
-
-/* these are part of the status read */
- short Tc_fwd;
- short Tc_bwd;
- short Tf_max;
- short Tb_max;
-
-/* add any new fields here above is a mirror of sdla_dlci_conf */
-};
-
-#define DLCI_GET_SLAVE (SIOCDEVPRIVATE + 4)
-
-/* configuration flags for DLCI */
-#define DLCI_IGNORE_CIR_OUT 0x0001
-#define DLCI_ACCOUNT_CIR_IN 0x0002
-#define DLCI_BUFFER_IF 0x0008
-
-#define DLCI_VALID_FLAGS 0x000B
-
-/* defines for the actual Frame Relay hardware */
-#define FRAD_GET_CONF (SIOCDEVPRIVATE)
-#define FRAD_SET_CONF (SIOCDEVPRIVATE + 1)
-
-#define FRAD_LAST_IOCTL FRAD_SET_CONF
-
-/*
- * Based on the setup for the Sangoma SDLA. If changes are
- * necessary to this structure, a routine will need to be
- * added to that module to copy fields.
- */
-struct frad_conf
-{
- short station;
- short flags;
- short kbaud;
- short clocking;
- short mtu;
- short T391;
- short T392;
- short N391;
- short N392;
- short N393;
- short CIR_fwd;
- short Bc_fwd;
- short Be_fwd;
- short CIR_bwd;
- short Bc_bwd;
- short Be_bwd;
-
-/* Add new fields here, above is a mirror of the sdla_conf */
-
-};
-
-#define FRAD_STATION_CPE 0x0000
-#define FRAD_STATION_NODE 0x0001
-
-#define FRAD_TX_IGNORE_CIR 0x0001
-#define FRAD_RX_ACCOUNT_CIR 0x0002
-#define FRAD_DROP_ABORTED 0x0004
-#define FRAD_BUFFERIF 0x0008
-#define FRAD_STATS 0x0010
-#define FRAD_MCI 0x0100
-#define FRAD_AUTODLCI 0x8000
-#define FRAD_VALID_FLAGS 0x811F
-
-#define FRAD_CLOCK_INT 0x0001
-#define FRAD_CLOCK_EXT 0x0000
-
-
-#endif /* _UAPI_FRAD_H_ */
deleted file mode 100644
@@ -1,117 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ WITH Linux-syscall-note */
-/*
- * INET An implementation of the TCP/IP protocol suite for the LINUX
- * operating system. INET is implemented using the BSD Socket
- * interface as the means of communication with the user level.
- *
- * Global definitions for the Frame relay interface.
- *
- * Version: @(#)if_ifrad.h 0.20 13 Apr 96
- *
- * Author: Mike McLagan <mike.mclagan@linux.org>
- *
- * Changes:
- * 0.15 Mike McLagan Structure packing
- *
- * 0.20 Mike McLagan New flags for S508 buffer handling
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#ifndef _UAPISDLA_H
-#define _UAPISDLA_H
-
-/* adapter type */
-#define SDLA_TYPES
-#define SDLA_S502A 5020
-#define SDLA_S502E 5021
-#define SDLA_S503 5030
-#define SDLA_S507 5070
-#define SDLA_S508 5080
-#define SDLA_S509 5090
-#define SDLA_UNKNOWN -1
-
-/* port selection flags for the S508 */
-#define SDLA_S508_PORT_V35 0x00
-#define SDLA_S508_PORT_RS232 0x02
-
-/* Z80 CPU speeds */
-#define SDLA_CPU_3M 0x00
-#define SDLA_CPU_5M 0x01
-#define SDLA_CPU_7M 0x02
-#define SDLA_CPU_8M 0x03
-#define SDLA_CPU_10M 0x04
-#define SDLA_CPU_16M 0x05
-#define SDLA_CPU_12M 0x06
-
-/* some private IOCTLs */
-#define SDLA_IDENTIFY (FRAD_LAST_IOCTL + 1)
-#define SDLA_CPUSPEED (FRAD_LAST_IOCTL + 2)
-#define SDLA_PROTOCOL (FRAD_LAST_IOCTL + 3)
-
-#define SDLA_CLEARMEM (FRAD_LAST_IOCTL + 4)
-#define SDLA_WRITEMEM (FRAD_LAST_IOCTL + 5)
-#define SDLA_READMEM (FRAD_LAST_IOCTL + 6)
-
-struct sdla_mem {
- int addr;
- int len;
- void __user *data;
-};
-
-#define SDLA_START (FRAD_LAST_IOCTL + 7)
-#define SDLA_STOP (FRAD_LAST_IOCTL + 8)
-
-/* some offsets in the Z80's memory space */
-#define SDLA_NMIADDR 0x0000
-#define SDLA_CONF_ADDR 0x0010
-#define SDLA_S502A_NMIADDR 0x0066
-#define SDLA_CODE_BASEADDR 0x0100
-#define SDLA_WINDOW_SIZE 0x2000
-#define SDLA_ADDR_MASK 0x1FFF
-
-/* largest handleable block of data */
-#define SDLA_MAX_DATA 4080
-#define SDLA_MAX_MTU 4072 /* MAX_DATA - sizeof(fradhdr) */
-#define SDLA_MAX_DLCI 24
-
-/* this should be the same as frad_conf */
-struct sdla_conf {
- short station;
- short config;
- short kbaud;
- short clocking;
- short max_frm;
- short T391;
- short T392;
- short N391;
- short N392;
- short N393;
- short CIR_fwd;
- short Bc_fwd;
- short Be_fwd;
- short CIR_bwd;
- short Bc_bwd;
- short Be_bwd;
-};
-
-/* this should be the same as dlci_conf */
-struct sdla_dlci_conf {
- short config;
- short CIR_fwd;
- short Bc_fwd;
- short Be_fwd;
- short CIR_bwd;
- short Bc_bwd;
- short Be_bwd;
- short Tc_fwd;
- short Tc_bwd;
- short Tf_max;
- short Tb_max;
-};
-
-
-#endif /* _UAPISDLA_H */
@@ -64,7 +64,6 @@
#include <linux/seq_file.h>
#include <linux/mutex.h>
#include <linux/if_bridge.h>
-#include <linux/if_frad.h>
#include <linux/if_vlan.h>
#include <linux/ptp_classify.h>
#include <linux/init.h>
@@ -1019,17 +1018,6 @@ void vlan_ioctl_set(int (*hook) (struct net *, void __user *))
}
EXPORT_SYMBOL(vlan_ioctl_set);
-static DEFINE_MUTEX(dlci_ioctl_mutex);
-static int (*dlci_ioctl_hook) (unsigned int, void __user *);
-
-void dlci_ioctl_set(int (*hook) (unsigned int, void __user *))
-{
- mutex_lock(&dlci_ioctl_mutex);
- dlci_ioctl_hook = hook;
- mutex_unlock(&dlci_ioctl_mutex);
-}
-EXPORT_SYMBOL(dlci_ioctl_set);
-
static long sock_do_ioctl(struct net *net, struct socket *sock,
unsigned int cmd, unsigned long arg)
{
@@ -1148,17 +1136,6 @@ static long sock_ioctl(struct file *file, unsigned cmd, unsigned long arg)
err = vlan_ioctl_hook(net, argp);
mutex_unlock(&vlan_ioctl_mutex);
break;
- case SIOCADDDLCI:
- case SIOCDELDLCI:
- err = -ENOPKG;
- if (!dlci_ioctl_hook)
- request_module("dlci");
-
- mutex_lock(&dlci_ioctl_mutex);
- if (dlci_ioctl_hook)
- err = dlci_ioctl_hook(cmd, argp);
- mutex_unlock(&dlci_ioctl_mutex);
- break;
case SIOCGSKNS:
err = -EPERM;
if (!ns_capable(net->user_ns, CAP_NET_ADMIN))
@@ -3403,8 +3380,6 @@ static int compat_sock_ioctl_trans(struct file *file, struct socket *sock,
case SIOCBRDELBR:
case SIOCGIFVLAN:
case SIOCSIFVLAN:
- case SIOCADDDLCI:
- case SIOCDELDLCI:
case SIOCGSKNS:
case SIOCGSTAMP_NEW:
case SIOCGSTAMPNS_NEW:
The DLCI framework and SDLA driver are as obsolete as it gets, this is an ISA add-on card from the mid-1990s that has only seen sporadic cleanups. The website listed for downloading the user space tools has dropped off the internet at some point around 2010, but Debian already dropped the packages ten years earlier when they no longer built correctly. Signed-off-by: Arnd Bergmann <arnd@arndb.de> --- Documentation/networking/framerelay.txt | 39 - MAINTAINERS | 6 - drivers/net/wan/Kconfig | 45 - drivers/net/wan/Makefile | 2 - drivers/net/wan/dlci.c | 542 -------- drivers/net/wan/sdla.c | 1655 ----------------------- include/Kbuild | 1 - include/linux/if_frad.h | 92 -- include/linux/sdla.h | 240 ---- include/uapi/linux/if_frad.h | 123 -- include/uapi/linux/sdla.h | 117 -- net/socket.c | 25 - 12 files changed, 2887 deletions(-) delete mode 100644 Documentation/networking/framerelay.txt delete mode 100644 drivers/net/wan/dlci.c delete mode 100644 drivers/net/wan/sdla.c delete mode 100644 include/linux/if_frad.h delete mode 100644 include/linux/sdla.h delete mode 100644 include/uapi/linux/if_frad.h delete mode 100644 include/uapi/linux/sdla.h -- 2.20.0