diff mbox series

[RFT,v2,10/10] drivers: qcom: rpmh-rsc: Always use -EAGAIN, never -EBUSY

Message ID 20200311161104.RFT.v2.10.I537337af59c51c72aac2c1625760a60519c66387@changeid
State New
Headers show
Series None | expand

Commit Message

Doug Anderson March 11, 2020, 11:13 p.m. UTC
Some parts of rpmh-rsc returned -EAGAIN when the controller was busy
and you should try again.  Other parts returned -EBUSY when the
controller was busy and you should try again.  Typically -EAGAIN was
used when dealing with sleep/wake TCSs and -EBUSY was used when
dealing with the active TCS.

Let's standardize and just have one return code.

If we don't do this then the crossover case where we need to use a
sleep/wake TCS for an active only transfer (when there are zero active
TCSs) we need to either adapt one code to the other test for both.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
---

Changes in v2:
- ("Always use -EAGAIN, never -EBUSY") new for v2.

 drivers/soc/qcom/rpmh-rsc.c | 19 +++++++++----------
 1 file changed, 9 insertions(+), 10 deletions(-)
diff mbox series

Patch

diff --git a/drivers/soc/qcom/rpmh-rsc.c b/drivers/soc/qcom/rpmh-rsc.c
index abbd8b158a63..8b59d07ef94e 100644
--- a/drivers/soc/qcom/rpmh-rsc.c
+++ b/drivers/soc/qcom/rpmh-rsc.c
@@ -497,11 +497,11 @@  static void __tcs_trigger(struct rsc_drv *drv, int tcs_id)
  *
  * This will walk through the TCSs in the group and check if any of them
  * appear to be sending to addresses referenced in the message.  If it finds
- * one it'll return -EBUSY.
+ * one it'll return -EAGAIN.
  *
  * Must be called with the drv->lock held since that protects tcs_in_use.
  *
- * Return: 0 if nothing in flight or -EBUSY if we should try again later.
+ * Return: 0 if nothing in flight or -EAGAIN if we should try again later.
  *         The caller must re-enable interrupts between tries since that's
  *         the only way tcs_is_free() will ever return true and the only way
  *         RSC_DRV_CMD_ENABLE will ever be cleared.
@@ -524,7 +524,7 @@  static int check_for_req_inflight(struct rsc_drv *drv, struct tcs_group *tcs,
 			addr = read_tcs_cmd(drv, RSC_DRV_CMD_ADDR, tcs_id, j);
 			for (k = 0; k < msg->num_cmds; k++) {
 				if (addr == msg->cmds[k].addr)
-					return -EBUSY;
+					return -EAGAIN;
 			}
 		}
 	}
@@ -550,21 +550,21 @@  static int find_free_tcs(struct tcs_group *tcs)
 			return tcs->offset + i;
 	}
 
-	return -EBUSY;
+	return -EAGAIN;
 }
 
 /**
- * tcs_write() - Store messages into a TCS right now, or return -EBUSY.
+ * tcs_write() - Store messages into a TCS right now, or return -EAGAIN.
  * @drv: The controller.
  * @msg: The data to be sent.
  *
  * Grabs a TCS for ACTIVE_ONLY transfers and writes the messages to it.
  *
  * If there are no free ACTIVE_ONLY TCSs or if a command for the same address
- * is already transferring returns -EBUSY which means the client should retry
+ * is already transferring returns -EAGAIN which means the client should retry
  * shortly.
  *
- * Return: 0 on success, -EBUSY if client should retry, or an error.
+ * Return: 0 on success, -EAGAIN if client should retry, or an error.
  *         Client should have interrupts enabled for a bit before retrying.
  */
 static int tcs_write(struct rsc_drv *drv, const struct tcs_request *msg)
@@ -580,7 +580,6 @@  static int tcs_write(struct rsc_drv *drv, const struct tcs_request *msg)
 	 */
 	WARN_ON(msg->state != RPMH_ACTIVE_ONLY_STATE);
 
-	/* TODO: get_tcs_for_msg() can return -EAGAIN and nobody handles */
 	tcs = get_tcs_for_msg(drv, msg);
 	if (IS_ERR(tcs))
 		return PTR_ERR(tcs);
@@ -651,12 +650,12 @@  int rpmh_rsc_send_data(struct rsc_drv *drv, const struct tcs_request *msg)
 
 	do {
 		ret = tcs_write(drv, msg);
-		if (ret == -EBUSY) {
+		if (ret == -EAGAIN) {
 			pr_info_ratelimited("TCS Busy, retrying RPMH message send: addr=%#x\n",
 					    msg->cmds[0].addr);
 			udelay(10);
 		}
-	} while (ret == -EBUSY);
+	} while (ret == -EAGAIN);
 
 	return ret;
 }