diff mbox series

[RFC,v4,1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements

Message ID 20200624022848.7765-2-wcheng@codeaurora.org
State Superseded
Headers show
Series [RFC,v4,1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements | expand

Commit Message

Wesley Cheng June 24, 2020, 2:28 a.m. UTC
Some devices have USB compositions which may require multiple endpoints
that support EP bursting.  HW defined TX FIFO sizes may not always be
sufficient for these compositions.  By utilizing flexible TX FIFO
allocation, this allows for endpoints to request the required FIFO depth to
achieve higher bandwidth.  With some higher bMaxBurst configurations, using
a larger TX FIFO size results in better TX throughput.

Ensure that one TX FIFO is reserved for every IN endpoint.  This allows for
the FIFO logic to prevent running out of FIFO space.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
---
 drivers/usb/dwc3/core.c   |   2 +
 drivers/usb/dwc3/core.h   |   8 +++
 drivers/usb/dwc3/ep0.c    |  37 +++++++++++-
 drivers/usb/dwc3/gadget.c | 115 ++++++++++++++++++++++++++++++++++++++
 4 files changed, 161 insertions(+), 1 deletion(-)

Comments

Felipe Balbi Aug. 10, 2020, 12:27 p.m. UTC | #1
Wesley Cheng <wcheng@codeaurora.org> writes:

Hi,

> Some devices have USB compositions which may require multiple endpoints

> that support EP bursting.  HW defined TX FIFO sizes may not always be

> sufficient for these compositions.  By utilizing flexible TX FIFO

> allocation, this allows for endpoints to request the required FIFO depth to

> achieve higher bandwidth.  With some higher bMaxBurst configurations, using

> a larger TX FIFO size results in better TX throughput.


how much better? What's the impact? Got some real numbers of this
running with upstream kernel? I guess mass storage gadget is the
simplest one to test.

> diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c

> index 6dee4dabc0a4..76db9b530861 100644

> --- a/drivers/usb/dwc3/ep0.c

> +++ b/drivers/usb/dwc3/ep0.c

> @@ -601,8 +601,9 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)

>  {

>  	enum usb_device_state state = dwc->gadget.state;

>  	u32 cfg;

> -	int ret;

> +	int ret, num, size;


no, no. Please one declaration per line.

>  	u32 reg;

> +	struct dwc3_ep *dep;


Keep reverse xmas tree order.

> @@ -611,6 +612,40 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)

>  		return -EINVAL;

>  

>  	case USB_STATE_ADDRESS:

> +		/*

> +		 * If tx-fifo-resize flag is not set for the controller, then

> +		 * do not clear existing allocated TXFIFO since we do not

> +		 * allocate it again in dwc3_gadget_resize_tx_fifos

> +		 */

> +		if (dwc->needs_fifo_resize) {

> +			/* Read ep0IN related TXFIFO size */

> +			dep = dwc->eps[1];

> +			size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));

> +			if (dwc3_is_usb31(dwc))

> +				dep->fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size);

> +			else

> +				dep->fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size);

> +

> +			dwc->last_fifo_depth = dep->fifo_depth;

> +			/* Clear existing TXFIFO for all IN eps except ep0 */

> +			for (num = 3; num < min_t(int, dwc->num_eps,

> +				DWC3_ENDPOINTS_NUM); num += 2) {

> +				dep = dwc->eps[num];

> +				/* Don't change TXFRAMNUM on usb31 version */

> +				size = dwc3_is_usb31(dwc) ?

> +					dwc3_readl(dwc->regs,

> +						   DWC3_GTXFIFOSIZ(num >> 1)) &

> +						   DWC31_GTXFIFOSIZ_TXFRAMNUM :

> +						   0;

> +

> +				dwc3_writel(dwc->regs,

> +					    DWC3_GTXFIFOSIZ(num >> 1),

> +					    size);

> +				dep->fifo_depth = 0;

> +			}

> +			dwc->num_ep_resized = 0;


care to move this into a helper that you call unconditionally and the
helper returns early is !needs_fifo_resize?

> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c

> index 00746c2848c0..777badf3e85d 100644

> --- a/drivers/usb/dwc3/gadget.c

> +++ b/drivers/usb/dwc3/gadget.c

> @@ -540,6 +540,117 @@ static int dwc3_gadget_start_config(struct dwc3_ep *dep)

>  	return 0;

>  }

>  

> +/*

> + * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case

> + * @dwc: pointer to our context structure

> + *

> + * This function will a best effort FIFO allocation in order

> + * to improve FIFO usage and throughput, while still allowing

> + * us to enable as many endpoints as possible.

> + *

> + * Keep in mind that this operation will be highly dependent

> + * on the configured size for RAM1 - which contains TxFifo -,

> + * the amount of endpoints enabled on coreConsultant tool, and

> + * the width of the Master Bus.

> + *

> + * In general, FIFO depths are represented with the following equation:

> + *

> + * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1

> + *

> + * Conversions can be done to the equation to derive the number of packets that

> + * will fit to a particular FIFO size value.

> + */

> +static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep)

> +{

> +	struct dwc3 *dwc = dep->dwc;

> +	int ram1_depth, mdwidth, fifo_0_start, tmp, num_in_ep;

> +	int min_depth, remaining, fifo_size, mult = 1, fifo, max_packet = 1024;


one declaration per line, also make sure you order it in reverse xmas
tree order.

> +	if (!dwc->needs_fifo_resize)

> +		return 0;

> +

> +	/* resize IN endpoints except ep0 */

> +	if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)

> +		return 0;

> +

> +	/* Don't resize already resized IN endpoint */

> +	if (dep->fifo_depth)


using fifo_depth as a flag seems flakey to me. What happens when someone
in the future changes the behavior below and this doesn't apply anymore?

Also, why is this procedure called more than once for the same endpoint?
Does that really happen?

> +		return 0;

> +

> +	ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);

> +	mdwidth = DWC3_MDWIDTH(dwc->hwparams.hwparams0);

> +	/* MDWIDTH is represented in bits, we need it in bytes */

> +	mdwidth >>= 3;

> +

> +	if (((dep->endpoint.maxburst > 1) &&

> +			usb_endpoint_xfer_bulk(dep->endpoint.desc))

> +			|| usb_endpoint_xfer_isoc(dep->endpoint.desc))

> +		mult = 3;

> +

> +	if ((dep->endpoint.maxburst > 6) &&

> +			usb_endpoint_xfer_bulk(dep->endpoint.desc)

> +			&& dwc3_is_usb31(dwc))

> +		mult = 6;

> +

> +	/* FIFO size for a single buffer */

> +	fifo = (max_packet + mdwidth)/mdwidth;


add spaces around integer division operator

> +	fifo++;

> +

> +	/* Calculate the number of remaining EPs w/o any FIFO */

> +	num_in_ep = dwc->num_eps/2;

> +	num_in_ep -= dwc->num_ep_resized;

> +	/* Ignore EP0 IN */

> +	num_in_ep--;

> +

> +	/* Reserve at least one FIFO for the number of IN EPs */

> +	min_depth = num_in_ep * (fifo+1);

> +	remaining = ram1_depth - min_depth - dwc->last_fifo_depth;

> +

> +	/* We've already reserved 1 FIFO per EP, so check what we can fit in


comment style is wrong

> +	 * addition to it.  If there is not enough remaining space, allocate

> +	 * all the remaining space to the EP.

> +	 */

> +	fifo_size = (mult-1) * fifo;


spaces around subtraction

> +	if (remaining < fifo_size) {

> +		if (remaining > 0)

> +			fifo_size = remaining;

> +		else

> +			fifo_size = 0;

> +	}

> +

> +	fifo_size += fifo;

> +	fifo_size++;


why the increment?

> +	dep->fifo_depth = fifo_size;

> +

> +	/* Check if TXFIFOs start at non-zero addr */

> +	tmp = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));

> +	fifo_0_start = DWC3_GTXFIFOSIZ_TXFSTADDR(tmp);

> +

> +	fifo_size |= (fifo_0_start + (dwc->last_fifo_depth << 16));

> +	if (dwc3_is_usb31(dwc))

> +		dwc->last_fifo_depth += DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);

> +	else

> +		dwc->last_fifo_depth += DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);

> +

> +	/* Check fifo size allocation doesn't exceed available RAM size. */

> +	if (dwc->last_fifo_depth >= ram1_depth) {

> +		dev_err(dwc->dev, "Fifosize(%d) > RAM size(%d) %s depth:%d\n",

> +				(dwc->last_fifo_depth * mdwidth), ram1_depth,

> +				dep->endpoint.name, fifo_size);

> +		if (dwc3_is_usb31(dwc))

> +			fifo_size = DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);

> +		else

> +			fifo_size = DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);

> +		dwc->last_fifo_depth -= fifo_size;

> +		dep->fifo_depth = 0;

> +		return -ENOMEM;

> +	}

> +

> +	dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1), fifo_size);

> +	dwc->num_ep_resized++;


add a blank line here

> +	return 0;

> +}

> +

>  static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action)

>  {

>  	const struct usb_ss_ep_comp_descriptor *comp_desc;

> @@ -620,6 +731,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)

>  	int			ret;

>  

>  	if (!(dep->flags & DWC3_EP_ENABLED)) {

> +		ret = dwc3_gadget_resize_tx_fifos(dep);

> +		if (ret)

> +			return ret;


doesn't it look odd that you're resizing every fifo every time a new
endpoint is enabled? Is there a better way to achieve this?

-- 
balbi
Wesley Cheng Aug. 11, 2020, 5:10 a.m. UTC | #2
On 8/10/2020 5:27 AM, Felipe Balbi wrote:
> Wesley Cheng <wcheng@codeaurora.org> writes:

> 

> Hi,

> 

>> Some devices have USB compositions which may require multiple endpoints

>> that support EP bursting.  HW defined TX FIFO sizes may not always be

>> sufficient for these compositions.  By utilizing flexible TX FIFO

>> allocation, this allows for endpoints to request the required FIFO depth to

>> achieve higher bandwidth.  With some higher bMaxBurst configurations, using

>> a larger TX FIFO size results in better TX throughput.

> 

> how much better? What's the impact? Got some real numbers of this

> running with upstream kernel? I guess mass storage gadget is the

> simplest one to test.

> 

Hi Felipe,

Thanks for the input.

Sorry for not including the numbers in the patch itself, but I did
mention the set of mass storage tests I ran w/ the upstream kernel on
SM8150 in the cover letter.  Let me just share that here:

Test Parameters:
 - Platform: Qualcomm SM8150
 - bMaxBurst = 6
 - USB req size = 256kB
 - Num of USB reqs = 16
 - USB Speed = Super-Speed
 - Function Driver: Mass Storage (w/ ramdisk)
 - Test Application: CrystalDiskMark

Results:

TXFIFO Depth = 3 max packets

Test Case | Data Size | AVG tput (in MB/s)
-------------------------------------------
Sequential|1 GB x     |
Read      |9 loops    | 193.60
	  |           | 195.86
          |           | 184.77
          |           | 193.60
-------------------------------------------

TXFIFO Depth = 6 max packets

Test Case | Data Size | AVG tput (in MB/s)
-------------------------------------------
Sequential|1 GB x     |
Read      |9 loops    | 287.35
	  |           | 304.94
          |           | 289.64
          |           | 293.61
-------------------------------------------

>> diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c

>> index 6dee4dabc0a4..76db9b530861 100644

>> --- a/drivers/usb/dwc3/ep0.c

>> +++ b/drivers/usb/dwc3/ep0.c

>> @@ -601,8 +601,9 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)

>>  {

>>  	enum usb_device_state state = dwc->gadget.state;

>>  	u32 cfg;

>> -	int ret;

>> +	int ret, num, size;

> 

> no, no. Please one declaration per line.

> 

Got it.
>>  	u32 reg;

>> +	struct dwc3_ep *dep;

> 

> Keep reverse xmas tree order.

> 

Understood.
>> @@ -611,6 +612,40 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)

>>  		return -EINVAL;

>>  

>>  	case USB_STATE_ADDRESS:

>> +		/*

>> +		 * If tx-fifo-resize flag is not set for the controller, then

>> +		 * do not clear existing allocated TXFIFO since we do not

>> +		 * allocate it again in dwc3_gadget_resize_tx_fifos

>> +		 */

>> +		if (dwc->needs_fifo_resize) {

>> +			/* Read ep0IN related TXFIFO size */

>> +			dep = dwc->eps[1];

>> +			size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));

>> +			if (dwc3_is_usb31(dwc))

>> +				dep->fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size);

>> +			else

>> +				dep->fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size);

>> +

>> +			dwc->last_fifo_depth = dep->fifo_depth;

>> +			/* Clear existing TXFIFO for all IN eps except ep0 */

>> +			for (num = 3; num < min_t(int, dwc->num_eps,

>> +				DWC3_ENDPOINTS_NUM); num += 2) {

>> +				dep = dwc->eps[num];

>> +				/* Don't change TXFRAMNUM on usb31 version */

>> +				size = dwc3_is_usb31(dwc) ?

>> +					dwc3_readl(dwc->regs,

>> +						   DWC3_GTXFIFOSIZ(num >> 1)) &

>> +						   DWC31_GTXFIFOSIZ_TXFRAMNUM :

>> +						   0;

>> +

>> +				dwc3_writel(dwc->regs,

>> +					    DWC3_GTXFIFOSIZ(num >> 1),

>> +					    size);

>> +				dep->fifo_depth = 0;

>> +			}

>> +			dwc->num_ep_resized = 0;

> 

> care to move this into a helper that you call unconditionally and the

> helper returns early is !needs_fifo_resize?

> 

Sure, I'll include that in the next revision.
>> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c

>> index 00746c2848c0..777badf3e85d 100644

>> --- a/drivers/usb/dwc3/gadget.c

>> +++ b/drivers/usb/dwc3/gadget.c

>> @@ -540,6 +540,117 @@ static int dwc3_gadget_start_config(struct dwc3_ep *dep)

>>  	return 0;

>>  }

>>  

>> +/*

>> + * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case

>> + * @dwc: pointer to our context structure

>> + *

>> + * This function will a best effort FIFO allocation in order

>> + * to improve FIFO usage and throughput, while still allowing

>> + * us to enable as many endpoints as possible.

>> + *

>> + * Keep in mind that this operation will be highly dependent

>> + * on the configured size for RAM1 - which contains TxFifo -,

>> + * the amount of endpoints enabled on coreConsultant tool, and

>> + * the width of the Master Bus.

>> + *

>> + * In general, FIFO depths are represented with the following equation:

>> + *

>> + * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1

>> + *

>> + * Conversions can be done to the equation to derive the number of packets that

>> + * will fit to a particular FIFO size value.

>> + */

>> +static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep)

>> +{

>> +	struct dwc3 *dwc = dep->dwc;

>> +	int ram1_depth, mdwidth, fifo_0_start, tmp, num_in_ep;

>> +	int min_depth, remaining, fifo_size, mult = 1, fifo, max_packet = 1024;

> 

> one declaration per line, also make sure you order it in reverse xmas

> tree order.

> 

Will make sure to fix this in further declarations.
>> +	if (!dwc->needs_fifo_resize)

>> +		return 0;

>> +

>> +	/* resize IN endpoints except ep0 */

>> +	if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)

>> +		return 0;

>> +

>> +	/* Don't resize already resized IN endpoint */

>> +	if (dep->fifo_depth)

> 

> using fifo_depth as a flag seems flakey to me. What happens when someone

> in the future changes the behavior below and this doesn't apply anymore?

> 

> Also, why is this procedure called more than once for the same endpoint?

> Does that really happen?

> 

I guess it can be considered a bug elsewhere (ie usb gadget or function
driver) if this happens twice.  Plus, if we decide to keep this in the
dwc3 enable endpoint path, the DWC3_EP_ENABLED flag will ensure it's
called only once as well.  Its probably overkill to check fifo_depth here.
>> +		return 0;

>> +

>> +	ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);

>> +	mdwidth = DWC3_MDWIDTH(dwc->hwparams.hwparams0);

>> +	/* MDWIDTH is represented in bits, we need it in bytes */

>> +	mdwidth >>= 3;

>> +

>> +	if (((dep->endpoint.maxburst > 1) &&

>> +			usb_endpoint_xfer_bulk(dep->endpoint.desc))

>> +			|| usb_endpoint_xfer_isoc(dep->endpoint.desc))

>> +		mult = 3;

>> +

>> +	if ((dep->endpoint.maxburst > 6) &&

>> +			usb_endpoint_xfer_bulk(dep->endpoint.desc)

>> +			&& dwc3_is_usb31(dwc))

>> +		mult = 6;

>> +

>> +	/* FIFO size for a single buffer */

>> +	fifo = (max_packet + mdwidth)/mdwidth;

> 

> add spaces around integer division operator

> 

>> +	fifo++;

>> +

>> +	/* Calculate the number of remaining EPs w/o any FIFO */

>> +	num_in_ep = dwc->num_eps/2;

>> +	num_in_ep -= dwc->num_ep_resized;

>> +	/* Ignore EP0 IN */

>> +	num_in_ep--;

>> +

>> +	/* Reserve at least one FIFO for the number of IN EPs */

>> +	min_depth = num_in_ep * (fifo+1);

>> +	remaining = ram1_depth - min_depth - dwc->last_fifo_depth;

>> +

>> +	/* We've already reserved 1 FIFO per EP, so check what we can fit in

> 

> comment style is wrong

> 

>> +	 * addition to it.  If there is not enough remaining space, allocate

>> +	 * all the remaining space to the EP.

>> +	 */

>> +	fifo_size = (mult-1) * fifo;

> 

> spaces around subtraction

> 

Will fix the formatting comments above.
>> +	if (remaining < fifo_size) {

>> +		if (remaining > 0)

>> +			fifo_size = remaining;

>> +		else

>> +			fifo_size = 0;

>> +	}

>> +

>> +	fifo_size += fifo;

>> +	fifo_size++;

> 

> why the increment?

> 

This is to account for the last +1 in the equation from the DWC3 databook:
fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1 <- this one

>> +	dep->fifo_depth = fifo_size;

>> +

>> +	/* Check if TXFIFOs start at non-zero addr */

>> +	tmp = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));

>> +	fifo_0_start = DWC3_GTXFIFOSIZ_TXFSTADDR(tmp);

>> +

>> +	fifo_size |= (fifo_0_start + (dwc->last_fifo_depth << 16));

>> +	if (dwc3_is_usb31(dwc))

>> +		dwc->last_fifo_depth += DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);

>> +	else

>> +		dwc->last_fifo_depth += DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);

>> +

>> +	/* Check fifo size allocation doesn't exceed available RAM size. */

>> +	if (dwc->last_fifo_depth >= ram1_depth) {

>> +		dev_err(dwc->dev, "Fifosize(%d) > RAM size(%d) %s depth:%d\n",

>> +				(dwc->last_fifo_depth * mdwidth), ram1_depth,

>> +				dep->endpoint.name, fifo_size);

>> +		if (dwc3_is_usb31(dwc))

>> +			fifo_size = DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);

>> +		else

>> +			fifo_size = DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);

>> +		dwc->last_fifo_depth -= fifo_size;

>> +		dep->fifo_depth = 0;

>> +		return -ENOMEM;

>> +	}

>> +

>> +	dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1), fifo_size);

>> +	dwc->num_ep_resized++;

> 

> add a blank line here

> 

>> +	return 0;

>> +}

>> +

>>  static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action)

>>  {

>>  	const struct usb_ss_ep_comp_descriptor *comp_desc;

>> @@ -620,6 +731,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)

>>  	int			ret;

>>  

>>  	if (!(dep->flags & DWC3_EP_ENABLED)) {

>> +		ret = dwc3_gadget_resize_tx_fifos(dep);

>> +		if (ret)

>> +			return ret;

> 

> doesn't it look odd that you're resizing every fifo every time a new

> endpoint is enabled? Is there a better way to achieve this?

> 

We're only resizing a single fifo per call, and clearing the previous
fifo configuration upon receiving the set address.  In the past, I know
the change was to resize all fifos after receiving the set configuration
packet.  With that approach, I believe we saw issues with some function
drivers that immediately queued a USB request during their set_alt()
routine, followed by the dwc3 ep0 driver calling the TX fifo resize
API.(as the tx fifo resize was executed after we delegated the set
config packet to the USB composite)

Thanks
Wesley

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Felipe Balbi Aug. 11, 2020, 7:12 a.m. UTC | #3
Hi,

Wesley Cheng <wcheng@codeaurora.org> writes:
> On 8/10/2020 5:27 AM, Felipe Balbi wrote:

>> Wesley Cheng <wcheng@codeaurora.org> writes:

>> 

>> Hi,

>> 

>>> Some devices have USB compositions which may require multiple endpoints

>>> that support EP bursting.  HW defined TX FIFO sizes may not always be

>>> sufficient for these compositions.  By utilizing flexible TX FIFO

>>> allocation, this allows for endpoints to request the required FIFO depth to

>>> achieve higher bandwidth.  With some higher bMaxBurst configurations, using

>>> a larger TX FIFO size results in better TX throughput.

>> 

>> how much better? What's the impact? Got some real numbers of this

>> running with upstream kernel? I guess mass storage gadget is the

>> simplest one to test.

>> 

> Hi Felipe,

>

> Thanks for the input.

>

> Sorry for not including the numbers in the patch itself, but I did

> mention the set of mass storage tests I ran w/ the upstream kernel on

> SM8150 in the cover letter.  Let me just share that here:

>

> Test Parameters:

>  - Platform: Qualcomm SM8150

>  - bMaxBurst = 6

>  - USB req size = 256kB

>  - Num of USB reqs = 16

>  - USB Speed = Super-Speed

>  - Function Driver: Mass Storage (w/ ramdisk)

>  - Test Application: CrystalDiskMark

>

> Results:

>

> TXFIFO Depth = 3 max packets

>

> Test Case | Data Size | AVG tput (in MB/s)

> -------------------------------------------

> Sequential|1 GB x     |

> Read      |9 loops    | 193.60

> 	  |           | 195.86

>           |           | 184.77

>           |           | 193.60

> -------------------------------------------

>

> TXFIFO Depth = 6 max packets

>

> Test Case | Data Size | AVG tput (in MB/s)

> -------------------------------------------

> Sequential|1 GB x     |

> Read      |9 loops    | 287.35

> 	  |           | 304.94

>           |           | 289.64

>           |           | 293.61

> -------------------------------------------


awesome, thanks a lot for this :-) It's a considerable increase in your
setup. My only fear here is that we may end up creating a situation
where we can't allocate enough FIFO for all endpoints. This is, of
course, a consequence of the fact that we enable one endpoint at a
time.

Perhaps we could envision a way where function driver requests endpoints
in bulk, i.e. combines all endpoint requirements into a single method
call for gadget framework and, consequently, for UDC.

>>> +	if (!dwc->needs_fifo_resize)

>>> +		return 0;

>>> +

>>> +	/* resize IN endpoints except ep0 */

>>> +	if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)

>>> +		return 0;

>>> +

>>> +	/* Don't resize already resized IN endpoint */

>>> +	if (dep->fifo_depth)

>> 

>> using fifo_depth as a flag seems flakey to me. What happens when someone

>> in the future changes the behavior below and this doesn't apply anymore?

>> 

>> Also, why is this procedure called more than once for the same endpoint?

>> Does that really happen?

>> 

> I guess it can be considered a bug elsewhere (ie usb gadget or function

> driver) if this happens twice.  Plus, if we decide to keep this in the

> dwc3 enable endpoint path, the DWC3_EP_ENABLED flag will ensure it's

> called only once as well.  Its probably overkill to check fifo_depth here.


We could add a dev_WARN_ONCE() just to catch any possible bugs elsewhere.

>>> +	if (remaining < fifo_size) {

>>> +		if (remaining > 0)

>>> +			fifo_size = remaining;

>>> +		else

>>> +			fifo_size = 0;

>>> +	}

>>> +

>>> +	fifo_size += fifo;

>>> +	fifo_size++;

>> 

>> why the increment?

>> 

> This is to account for the last +1 in the equation from the DWC3 databook:

> fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1 <- this one


great, could you add this detail as a comment so it doesn't look as
cryptic? :-)

>>> +	return 0;

>>> +}

>>> +

>>>  static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action)

>>>  {

>>>  	const struct usb_ss_ep_comp_descriptor *comp_desc;

>>> @@ -620,6 +731,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)

>>>  	int			ret;

>>>  

>>>  	if (!(dep->flags & DWC3_EP_ENABLED)) {

>>> +		ret = dwc3_gadget_resize_tx_fifos(dep);

>>> +		if (ret)

>>> +			return ret;

>> 

>> doesn't it look odd that you're resizing every fifo every time a new

>> endpoint is enabled? Is there a better way to achieve this?

>> 

> We're only resizing a single fifo per call, and clearing the previous

> fifo configuration upon receiving the set address.  In the past, I know

> the change was to resize all fifos after receiving the set configuration

> packet.  With that approach, I believe we saw issues with some function

> drivers that immediately queued a USB request during their set_alt()

> routine, followed by the dwc3 ep0 driver calling the TX fifo resize

> API.(as the tx fifo resize was executed after we delegated the set

> config packet to the USB composite)


I don't remember seeing such an issue. Allocating FIFOs after we know
the entire requirements would avoid another possible situation, that of
dwc3 exausting FIFO space before it knows there are more enpdoints to
enable.

One possibility around this was suggested above, something along the
lines of:

	usb_gadget_ep_enable_bulk(struct usb_gadget *, struct
		usb_ep_alloc_desc *alloc_desc)

(please think of better names, I'm hopeless haha)

-- 
balbi
Alan Stern Aug. 11, 2020, 1:44 p.m. UTC | #4
On Tue, Aug 11, 2020 at 10:12:41AM +0300, Felipe Balbi wrote:
> One possibility around this was suggested above, something along the

> lines of:

> 

> 	usb_gadget_ep_enable_bulk(struct usb_gadget *, struct

> 		usb_ep_alloc_desc *alloc_desc)

> 

> (please think of better names, I'm hopeless haha)


How about usb_gadget_enable_endpoints()?

Alan Stern
Peter Chen Aug. 12, 2020, 2:22 a.m. UTC | #5
On Wed, Jun 24, 2020 at 10:31 AM Wesley Cheng <wcheng@codeaurora.org> wrote:
>

> Some devices have USB compositions which may require multiple endpoints

> that support EP bursting.  HW defined TX FIFO sizes may not always be

> sufficient for these compositions.  By utilizing flexible TX FIFO

> allocation, this allows for endpoints to request the required FIFO depth to

> achieve higher bandwidth.  With some higher bMaxBurst configurations, using

> a larger TX FIFO size results in better TX throughput.

>

> Ensure that one TX FIFO is reserved for every IN endpoint.  This allows for

> the FIFO logic to prevent running out of FIFO space.

>


You may do this for only allocated endpoints, but you need override
default .match_ep
API. See cdns3/gadget.c and cdns3/ep0.c as an example.

Peter

> Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>

> ---

>  drivers/usb/dwc3/core.c   |   2 +

>  drivers/usb/dwc3/core.h   |   8 +++

>  drivers/usb/dwc3/ep0.c    |  37 +++++++++++-

>  drivers/usb/dwc3/gadget.c | 115 ++++++++++++++++++++++++++++++++++++++

>  4 files changed, 161 insertions(+), 1 deletion(-)

>

> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c

> index edc17155cb2b..cca555493929 100644

> --- a/drivers/usb/dwc3/core.c

> +++ b/drivers/usb/dwc3/core.c

> @@ -1304,6 +1304,8 @@ static void dwc3_get_properties(struct dwc3 *dwc)

>                                 &tx_thr_num_pkt_prd);

>         device_property_read_u8(dev, "snps,tx-max-burst-prd",

>                                 &tx_max_burst_prd);

> +       dwc->needs_fifo_resize = device_property_read_bool(dev,

> +                               "tx-fifo-resize");

>

>         dwc->disable_scramble_quirk = device_property_read_bool(dev,

>                                 "snps,disable_scramble_quirk");

> diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h

> index 4c171a8e215f..ce0bf288b6ac 100644

> --- a/drivers/usb/dwc3/core.h

> +++ b/drivers/usb/dwc3/core.h

> @@ -675,6 +675,7 @@ struct dwc3_event_buffer {

>   *             isochronous START TRANSFER command failure workaround

>   * @start_cmd_status: the status of testing START TRANSFER command with

>   *             combo_num = 'b00

> + * @fifo_depth: allocated TXFIFO depth

>   */

>  struct dwc3_ep {

>         struct usb_ep           endpoint;

> @@ -727,6 +728,7 @@ struct dwc3_ep {

>         /* For isochronous START TRANSFER workaround only */

>         u8                      combo_num;

>         int                     start_cmd_status;

> +       int                     fifo_depth;

>  };

>

>  enum dwc3_phy {

> @@ -1004,6 +1006,7 @@ struct dwc3_scratchpad_array {

>   *     1       - utmi_l1_suspend_n

>   * @is_fpga: true when we are using the FPGA board

>   * @pending_events: true when we have pending IRQs to be handled

> + * @needs_fifo_resize: not all users might want fifo resizing, flag it

>   * @pullups_connected: true when Run/Stop bit is set

>   * @setup_packet_pending: true when there's a Setup Packet in FIFO. Workaround

>   * @three_stage_setup: set if we perform a three phase setup

> @@ -1044,6 +1047,8 @@ struct dwc3_scratchpad_array {

>   * @dis_metastability_quirk: set to disable metastability quirk.

>   * @imod_interval: set the interrupt moderation interval in 250ns

>   *                 increments or 0 to disable.

> + * @last_fifo_depth: total TXFIFO depth of all enabled USB IN/INT endpoints

> + * @num_ep_resized: the number of TX FIFOs that have already been resized

>   */

>  struct dwc3 {

>         struct work_struct      drd_work;

> @@ -1204,6 +1209,7 @@ struct dwc3 {

>         unsigned                is_utmi_l1_suspend:1;

>         unsigned                is_fpga:1;

>         unsigned                pending_events:1;

> +       unsigned                needs_fifo_resize:1;

>         unsigned                pullups_connected:1;

>         unsigned                setup_packet_pending:1;

>         unsigned                three_stage_setup:1;

> @@ -1236,6 +1242,8 @@ struct dwc3 {

>         unsigned                dis_metastability_quirk:1;

>

>         u16                     imod_interval;

> +       int                     last_fifo_depth;

> +       int                     num_ep_resized;

>  };

>

>  #define INCRX_BURST_MODE 0

> diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c

> index 6dee4dabc0a4..76db9b530861 100644

> --- a/drivers/usb/dwc3/ep0.c

> +++ b/drivers/usb/dwc3/ep0.c

> @@ -601,8 +601,9 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)

>  {

>         enum usb_device_state state = dwc->gadget.state;

>         u32 cfg;

> -       int ret;

> +       int ret, num, size;

>         u32 reg;

> +       struct dwc3_ep *dep;

>

>         cfg = le16_to_cpu(ctrl->wValue);

>

> @@ -611,6 +612,40 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)

>                 return -EINVAL;

>

>         case USB_STATE_ADDRESS:

> +               /*

> +                * If tx-fifo-resize flag is not set for the controller, then

> +                * do not clear existing allocated TXFIFO since we do not

> +                * allocate it again in dwc3_gadget_resize_tx_fifos

> +                */

> +               if (dwc->needs_fifo_resize) {

> +                       /* Read ep0IN related TXFIFO size */

> +                       dep = dwc->eps[1];

> +                       size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));

> +                       if (dwc3_is_usb31(dwc))

> +                               dep->fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size);

> +                       else

> +                               dep->fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size);

> +

> +                       dwc->last_fifo_depth = dep->fifo_depth;

> +                       /* Clear existing TXFIFO for all IN eps except ep0 */

> +                       for (num = 3; num < min_t(int, dwc->num_eps,

> +                               DWC3_ENDPOINTS_NUM); num += 2) {

> +                               dep = dwc->eps[num];

> +                               /* Don't change TXFRAMNUM on usb31 version */

> +                               size = dwc3_is_usb31(dwc) ?

> +                                       dwc3_readl(dwc->regs,

> +                                                  DWC3_GTXFIFOSIZ(num >> 1)) &

> +                                                  DWC31_GTXFIFOSIZ_TXFRAMNUM :

> +                                                  0;

> +

> +                               dwc3_writel(dwc->regs,

> +                                           DWC3_GTXFIFOSIZ(num >> 1),

> +                                           size);

> +                               dep->fifo_depth = 0;

> +                       }

> +                       dwc->num_ep_resized = 0;

> +               }

> +

>                 ret = dwc3_ep0_delegate_req(dwc, ctrl);

>                 /* if the cfg matches and the cfg is non zero */

>                 if (cfg && (!ret || (ret == USB_GADGET_DELAYED_STATUS))) {

> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c

> index 00746c2848c0..777badf3e85d 100644

> --- a/drivers/usb/dwc3/gadget.c

> +++ b/drivers/usb/dwc3/gadget.c

> @@ -540,6 +540,117 @@ static int dwc3_gadget_start_config(struct dwc3_ep *dep)

>         return 0;

>  }

>

> +/*

> + * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case

> + * @dwc: pointer to our context structure

> + *

> + * This function will a best effort FIFO allocation in order

> + * to improve FIFO usage and throughput, while still allowing

> + * us to enable as many endpoints as possible.

> + *

> + * Keep in mind that this operation will be highly dependent

> + * on the configured size for RAM1 - which contains TxFifo -,

> + * the amount of endpoints enabled on coreConsultant tool, and

> + * the width of the Master Bus.

> + *

> + * In general, FIFO depths are represented with the following equation:

> + *

> + * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1

> + *

> + * Conversions can be done to the equation to derive the number of packets that

> + * will fit to a particular FIFO size value.

> + */

> +static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep)

> +{

> +       struct dwc3 *dwc = dep->dwc;

> +       int ram1_depth, mdwidth, fifo_0_start, tmp, num_in_ep;

> +       int min_depth, remaining, fifo_size, mult = 1, fifo, max_packet = 1024;

> +

> +       if (!dwc->needs_fifo_resize)

> +               return 0;

> +

> +       /* resize IN endpoints except ep0 */

> +       if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)

> +               return 0;

> +

> +       /* Don't resize already resized IN endpoint */

> +       if (dep->fifo_depth)

> +               return 0;

> +

> +       ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);

> +       mdwidth = DWC3_MDWIDTH(dwc->hwparams.hwparams0);

> +       /* MDWIDTH is represented in bits, we need it in bytes */

> +       mdwidth >>= 3;

> +

> +       if (((dep->endpoint.maxburst > 1) &&

> +                       usb_endpoint_xfer_bulk(dep->endpoint.desc))

> +                       || usb_endpoint_xfer_isoc(dep->endpoint.desc))

> +               mult = 3;

> +

> +       if ((dep->endpoint.maxburst > 6) &&

> +                       usb_endpoint_xfer_bulk(dep->endpoint.desc)

> +                       && dwc3_is_usb31(dwc))

> +               mult = 6;

> +

> +       /* FIFO size for a single buffer */

> +       fifo = (max_packet + mdwidth)/mdwidth;

> +       fifo++;

> +

> +       /* Calculate the number of remaining EPs w/o any FIFO */

> +       num_in_ep = dwc->num_eps/2;

> +       num_in_ep -= dwc->num_ep_resized;

> +       /* Ignore EP0 IN */

> +       num_in_ep--;

> +

> +       /* Reserve at least one FIFO for the number of IN EPs */

> +       min_depth = num_in_ep * (fifo+1);

> +       remaining = ram1_depth - min_depth - dwc->last_fifo_depth;

> +

> +       /* We've already reserved 1 FIFO per EP, so check what we can fit in

> +        * addition to it.  If there is not enough remaining space, allocate

> +        * all the remaining space to the EP.

> +        */

> +       fifo_size = (mult-1) * fifo;

> +       if (remaining < fifo_size) {

> +               if (remaining > 0)

> +                       fifo_size = remaining;

> +               else

> +                       fifo_size = 0;

> +       }

> +

> +       fifo_size += fifo;

> +       fifo_size++;

> +       dep->fifo_depth = fifo_size;

> +

> +       /* Check if TXFIFOs start at non-zero addr */

> +       tmp = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));

> +       fifo_0_start = DWC3_GTXFIFOSIZ_TXFSTADDR(tmp);

> +

> +       fifo_size |= (fifo_0_start + (dwc->last_fifo_depth << 16));

> +       if (dwc3_is_usb31(dwc))

> +               dwc->last_fifo_depth += DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);

> +       else

> +               dwc->last_fifo_depth += DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);

> +

> +       /* Check fifo size allocation doesn't exceed available RAM size. */

> +       if (dwc->last_fifo_depth >= ram1_depth) {

> +               dev_err(dwc->dev, "Fifosize(%d) > RAM size(%d) %s depth:%d\n",

> +                               (dwc->last_fifo_depth * mdwidth), ram1_depth,

> +                               dep->endpoint.name, fifo_size);

> +               if (dwc3_is_usb31(dwc))

> +                       fifo_size = DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);

> +               else

> +                       fifo_size = DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);

> +               dwc->last_fifo_depth -= fifo_size;

> +               dep->fifo_depth = 0;

> +               return -ENOMEM;

> +       }

> +

> +       dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1), fifo_size);

> +       dwc->num_ep_resized++;

> +       return 0;

> +}

> +

>  static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action)

>  {

>         const struct usb_ss_ep_comp_descriptor *comp_desc;

> @@ -620,6 +731,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)

>         int                     ret;

>

>         if (!(dep->flags & DWC3_EP_ENABLED)) {

> +               ret = dwc3_gadget_resize_tx_fifos(dep);

> +               if (ret)

> +                       return ret;

> +

>                 ret = dwc3_gadget_start_config(dep);

>                 if (ret)

>                         return ret;

> --

> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,

> a Linux Foundation Collaborative Project

>
Peter Chen Aug. 12, 2020, 11:01 a.m. UTC | #6
> 

> Thank you for your input.  I've actually considered doing some matching/resizing in

> the .match_ep route as well, but it doesn't work well for situations where multiple

> configurations are in play. The reason being that if you look at the epautoconf APIs,

> the configfs driver will use the usb_ep_autoconfig_reset() to reset the endpoints

> claimed between initialization of each configuration.  This means that the

> epautoconf driver expects to re-use the usb_endpoints:

> 

> static int configfs_composite_bind(struct usb_gadget *gadget,

> 	struct usb_gadget_driver *gdriver)

> {

> ...

> 

> /* Go through all configs, attach all functions */ list_for_each_entry(c, &gi-

> >cdev.configs, list) { ...

> list_for_each_entry_safe(f, tmp, &cfg->func_list, list) {

> 	list_del(&f->list);

> 	ret = usb_add_function(c, f);

> 	if (ret) {

> 		list_add(&f->list, &cfg->func_list);

> 		goto err_purge_funcs;

> 	}

> }

> usb_ep_autoconfig_reset(cdev->gadget);

> }

> 

> So in this situation, I wouldn't want the dwc3 gadget driver to assign a different

> dwc3 ep for endpoints in each configuration, when we know that only one set of

> EPs will be active when the host chooses.  I hope I understood your feedback

> correctly, and definitely appreciate the input!

> 

 
Thanks for mention that, we didn't consider multiple configurations use case, it needs
the UDC driver to record the configuration information, it is too complex at current framework.

I think your solution is OK, reserving one packet for each IN endpoint to avoid running out of
FIFO for later endpoints and fit the first endpoints with larger FIFO room to get the best
performance, it could use as many as FIFOs the device owns.

Peter
Wesley Cheng Aug. 12, 2020, 6:34 p.m. UTC | #7
On 8/11/2020 12:12 AM, Felipe Balbi wrote:
> 

> Hi,

> 

> Wesley Cheng <wcheng@codeaurora.org> writes:

>> On 8/10/2020 5:27 AM, Felipe Balbi wrote:

>>> Wesley Cheng <wcheng@codeaurora.org> writes:

>>>

>>> Hi,

>>>

>>>> Some devices have USB compositions which may require multiple endpoints

>>>> that support EP bursting.  HW defined TX FIFO sizes may not always be

>>>> sufficient for these compositions.  By utilizing flexible TX FIFO

>>>> allocation, this allows for endpoints to request the required FIFO depth to

>>>> achieve higher bandwidth.  With some higher bMaxBurst configurations, using

>>>> a larger TX FIFO size results in better TX throughput.

>>>

>>> how much better? What's the impact? Got some real numbers of this

>>> running with upstream kernel? I guess mass storage gadget is the

>>> simplest one to test.

>>>

>> Hi Felipe,

>>

>> Thanks for the input.

>>

>> Sorry for not including the numbers in the patch itself, but I did

>> mention the set of mass storage tests I ran w/ the upstream kernel on

>> SM8150 in the cover letter.  Let me just share that here:

>>

>> Test Parameters:

>>  - Platform: Qualcomm SM8150

>>  - bMaxBurst = 6

>>  - USB req size = 256kB

>>  - Num of USB reqs = 16

>>  - USB Speed = Super-Speed

>>  - Function Driver: Mass Storage (w/ ramdisk)

>>  - Test Application: CrystalDiskMark

>>

>> Results:

>>

>> TXFIFO Depth = 3 max packets

>>

>> Test Case | Data Size | AVG tput (in MB/s)

>> -------------------------------------------

>> Sequential|1 GB x     |

>> Read      |9 loops    | 193.60

>> 	  |           | 195.86

>>           |           | 184.77

>>           |           | 193.60

>> -------------------------------------------

>>

>> TXFIFO Depth = 6 max packets

>>

>> Test Case | Data Size | AVG tput (in MB/s)

>> -------------------------------------------

>> Sequential|1 GB x     |

>> Read      |9 loops    | 287.35

>> 	  |           | 304.94

>>           |           | 289.64

>>           |           | 293.61

>> -------------------------------------------

> 

> awesome, thanks a lot for this :-) It's a considerable increase in your

> setup. My only fear here is that we may end up creating a situation

> where we can't allocate enough FIFO for all endpoints. This is, of

> course, a consequence of the fact that we enable one endpoint at a

> time.

> 

> Perhaps we could envision a way where function driver requests endpoints

> in bulk, i.e. combines all endpoint requirements into a single method

> call for gadget framework and, consequently, for UDC.

> 

Hi Felipe,

I agree...Resizing the txfifo is not as straightforward as it sounds :).
 Would be interesting to see how this affects tput on other platforms as
well.  We had a few discussions within our team, and came up with the
logic implemented in this patch to reserve at least 1 txfifo per
endpoint. Then we allocate any additional fifo space requests based on
the remaining space left.  That way we could avoid over allocating, but
the trade off is that we may have unused EPs taking up fifo space.

I didn't consider branching out to changing the gadget framework, so let
me take a look at your suggestion to see how it turns out.

>>>> +	if (!dwc->needs_fifo_resize)

>>>> +		return 0;

>>>> +

>>>> +	/* resize IN endpoints except ep0 */

>>>> +	if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)

>>>> +		return 0;

>>>> +

>>>> +	/* Don't resize already resized IN endpoint */

>>>> +	if (dep->fifo_depth)

>>>

>>> using fifo_depth as a flag seems flakey to me. What happens when someone

>>> in the future changes the behavior below and this doesn't apply anymore?

>>>

>>> Also, why is this procedure called more than once for the same endpoint?

>>> Does that really happen?

>>>

>> I guess it can be considered a bug elsewhere (ie usb gadget or function

>> driver) if this happens twice.  Plus, if we decide to keep this in the

>> dwc3 enable endpoint path, the DWC3_EP_ENABLED flag will ensure it's

>> called only once as well.  Its probably overkill to check fifo_depth here.

> 

> We could add a dev_WARN_ONCE() just to catch any possible bugs elsewhere.

> 


OK, I can add that.

>>>> +	if (remaining < fifo_size) {

>>>> +		if (remaining > 0)

>>>> +			fifo_size = remaining;

>>>> +		else

>>>> +			fifo_size = 0;

>>>> +	}

>>>> +

>>>> +	fifo_size += fifo;

>>>> +	fifo_size++;

>>>

>>> why the increment?

>>>

>> This is to account for the last +1 in the equation from the DWC3 databook:

>> fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1 <- this one

> 

> great, could you add this detail as a comment so it doesn't look as

> cryptic? :-)

> 


Sure, of course.

>>>> +	return 0;

>>>> +}

>>>> +

>>>>  static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action)

>>>>  {

>>>>  	const struct usb_ss_ep_comp_descriptor *comp_desc;

>>>> @@ -620,6 +731,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)

>>>>  	int			ret;

>>>>  

>>>>  	if (!(dep->flags & DWC3_EP_ENABLED)) {

>>>> +		ret = dwc3_gadget_resize_tx_fifos(dep);

>>>> +		if (ret)

>>>> +			return ret;

>>>

>>> doesn't it look odd that you're resizing every fifo every time a new

>>> endpoint is enabled? Is there a better way to achieve this?

>>>

>> We're only resizing a single fifo per call, and clearing the previous

>> fifo configuration upon receiving the set address.  In the past, I know

>> the change was to resize all fifos after receiving the set configuration

>> packet.  With that approach, I believe we saw issues with some function

>> drivers that immediately queued a USB request during their set_alt()

>> routine, followed by the dwc3 ep0 driver calling the TX fifo resize

>> API.(as the tx fifo resize was executed after we delegated the set

>> config packet to the USB composite)

> 

> I don't remember seeing such an issue. Allocating FIFOs after we know

> the entire requirements would avoid another possible situation, that of

> dwc3 exausting FIFO space before it knows there are more enpdoints to

> enable.

> 

> One possibility around this was suggested above, something along the

> lines of:

> 

> 	usb_gadget_ep_enable_bulk(struct usb_gadget *, struct

> 		usb_ep_alloc_desc *alloc_desc)

> 

> (please think of better names, I'm hopeless haha)

> 

Sorry forgot to mention that this is something we caught internally with
our testing using the older txfifo resizing change.  As mentioned above,
let me dive into this suggestion a bit more.

Thanks
Wesley

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
diff mbox series

Patch

diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index edc17155cb2b..cca555493929 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -1304,6 +1304,8 @@  static void dwc3_get_properties(struct dwc3 *dwc)
 				&tx_thr_num_pkt_prd);
 	device_property_read_u8(dev, "snps,tx-max-burst-prd",
 				&tx_max_burst_prd);
+	dwc->needs_fifo_resize = device_property_read_bool(dev,
+				"tx-fifo-resize");
 
 	dwc->disable_scramble_quirk = device_property_read_bool(dev,
 				"snps,disable_scramble_quirk");
diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index 4c171a8e215f..ce0bf288b6ac 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -675,6 +675,7 @@  struct dwc3_event_buffer {
  *		isochronous START TRANSFER command failure workaround
  * @start_cmd_status: the status of testing START TRANSFER command with
  *		combo_num = 'b00
+ * @fifo_depth: allocated TXFIFO depth
  */
 struct dwc3_ep {
 	struct usb_ep		endpoint;
@@ -727,6 +728,7 @@  struct dwc3_ep {
 	/* For isochronous START TRANSFER workaround only */
 	u8			combo_num;
 	int			start_cmd_status;
+	int			fifo_depth;
 };
 
 enum dwc3_phy {
@@ -1004,6 +1006,7 @@  struct dwc3_scratchpad_array {
  * 	1	- utmi_l1_suspend_n
  * @is_fpga: true when we are using the FPGA board
  * @pending_events: true when we have pending IRQs to be handled
+ * @needs_fifo_resize: not all users might want fifo resizing, flag it
  * @pullups_connected: true when Run/Stop bit is set
  * @setup_packet_pending: true when there's a Setup Packet in FIFO. Workaround
  * @three_stage_setup: set if we perform a three phase setup
@@ -1044,6 +1047,8 @@  struct dwc3_scratchpad_array {
  * @dis_metastability_quirk: set to disable metastability quirk.
  * @imod_interval: set the interrupt moderation interval in 250ns
  *                 increments or 0 to disable.
+ * @last_fifo_depth: total TXFIFO depth of all enabled USB IN/INT endpoints
+ * @num_ep_resized: the number of TX FIFOs that have already been resized
  */
 struct dwc3 {
 	struct work_struct	drd_work;
@@ -1204,6 +1209,7 @@  struct dwc3 {
 	unsigned		is_utmi_l1_suspend:1;
 	unsigned		is_fpga:1;
 	unsigned		pending_events:1;
+	unsigned		needs_fifo_resize:1;
 	unsigned		pullups_connected:1;
 	unsigned		setup_packet_pending:1;
 	unsigned		three_stage_setup:1;
@@ -1236,6 +1242,8 @@  struct dwc3 {
 	unsigned		dis_metastability_quirk:1;
 
 	u16			imod_interval;
+	int			last_fifo_depth;
+	int			num_ep_resized;
 };
 
 #define INCRX_BURST_MODE 0
diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c
index 6dee4dabc0a4..76db9b530861 100644
--- a/drivers/usb/dwc3/ep0.c
+++ b/drivers/usb/dwc3/ep0.c
@@ -601,8 +601,9 @@  static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)
 {
 	enum usb_device_state state = dwc->gadget.state;
 	u32 cfg;
-	int ret;
+	int ret, num, size;
 	u32 reg;
+	struct dwc3_ep *dep;
 
 	cfg = le16_to_cpu(ctrl->wValue);
 
@@ -611,6 +612,40 @@  static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)
 		return -EINVAL;
 
 	case USB_STATE_ADDRESS:
+		/*
+		 * If tx-fifo-resize flag is not set for the controller, then
+		 * do not clear existing allocated TXFIFO since we do not
+		 * allocate it again in dwc3_gadget_resize_tx_fifos
+		 */
+		if (dwc->needs_fifo_resize) {
+			/* Read ep0IN related TXFIFO size */
+			dep = dwc->eps[1];
+			size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));
+			if (dwc3_is_usb31(dwc))
+				dep->fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size);
+			else
+				dep->fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size);
+
+			dwc->last_fifo_depth = dep->fifo_depth;
+			/* Clear existing TXFIFO for all IN eps except ep0 */
+			for (num = 3; num < min_t(int, dwc->num_eps,
+				DWC3_ENDPOINTS_NUM); num += 2) {
+				dep = dwc->eps[num];
+				/* Don't change TXFRAMNUM on usb31 version */
+				size = dwc3_is_usb31(dwc) ?
+					dwc3_readl(dwc->regs,
+						   DWC3_GTXFIFOSIZ(num >> 1)) &
+						   DWC31_GTXFIFOSIZ_TXFRAMNUM :
+						   0;
+
+				dwc3_writel(dwc->regs,
+					    DWC3_GTXFIFOSIZ(num >> 1),
+					    size);
+				dep->fifo_depth = 0;
+			}
+			dwc->num_ep_resized = 0;
+		}
+
 		ret = dwc3_ep0_delegate_req(dwc, ctrl);
 		/* if the cfg matches and the cfg is non zero */
 		if (cfg && (!ret || (ret == USB_GADGET_DELAYED_STATUS))) {
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 00746c2848c0..777badf3e85d 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -540,6 +540,117 @@  static int dwc3_gadget_start_config(struct dwc3_ep *dep)
 	return 0;
 }
 
+/*
+ * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case
+ * @dwc: pointer to our context structure
+ *
+ * This function will a best effort FIFO allocation in order
+ * to improve FIFO usage and throughput, while still allowing
+ * us to enable as many endpoints as possible.
+ *
+ * Keep in mind that this operation will be highly dependent
+ * on the configured size for RAM1 - which contains TxFifo -,
+ * the amount of endpoints enabled on coreConsultant tool, and
+ * the width of the Master Bus.
+ *
+ * In general, FIFO depths are represented with the following equation:
+ *
+ * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
+ *
+ * Conversions can be done to the equation to derive the number of packets that
+ * will fit to a particular FIFO size value.
+ */
+static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep)
+{
+	struct dwc3 *dwc = dep->dwc;
+	int ram1_depth, mdwidth, fifo_0_start, tmp, num_in_ep;
+	int min_depth, remaining, fifo_size, mult = 1, fifo, max_packet = 1024;
+
+	if (!dwc->needs_fifo_resize)
+		return 0;
+
+	/* resize IN endpoints except ep0 */
+	if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)
+		return 0;
+
+	/* Don't resize already resized IN endpoint */
+	if (dep->fifo_depth)
+		return 0;
+
+	ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);
+	mdwidth = DWC3_MDWIDTH(dwc->hwparams.hwparams0);
+	/* MDWIDTH is represented in bits, we need it in bytes */
+	mdwidth >>= 3;
+
+	if (((dep->endpoint.maxburst > 1) &&
+			usb_endpoint_xfer_bulk(dep->endpoint.desc))
+			|| usb_endpoint_xfer_isoc(dep->endpoint.desc))
+		mult = 3;
+
+	if ((dep->endpoint.maxburst > 6) &&
+			usb_endpoint_xfer_bulk(dep->endpoint.desc)
+			&& dwc3_is_usb31(dwc))
+		mult = 6;
+
+	/* FIFO size for a single buffer */
+	fifo = (max_packet + mdwidth)/mdwidth;
+	fifo++;
+
+	/* Calculate the number of remaining EPs w/o any FIFO */
+	num_in_ep = dwc->num_eps/2;
+	num_in_ep -= dwc->num_ep_resized;
+	/* Ignore EP0 IN */
+	num_in_ep--;
+
+	/* Reserve at least one FIFO for the number of IN EPs */
+	min_depth = num_in_ep * (fifo+1);
+	remaining = ram1_depth - min_depth - dwc->last_fifo_depth;
+
+	/* We've already reserved 1 FIFO per EP, so check what we can fit in
+	 * addition to it.  If there is not enough remaining space, allocate
+	 * all the remaining space to the EP.
+	 */
+	fifo_size = (mult-1) * fifo;
+	if (remaining < fifo_size) {
+		if (remaining > 0)
+			fifo_size = remaining;
+		else
+			fifo_size = 0;
+	}
+
+	fifo_size += fifo;
+	fifo_size++;
+	dep->fifo_depth = fifo_size;
+
+	/* Check if TXFIFOs start at non-zero addr */
+	tmp = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));
+	fifo_0_start = DWC3_GTXFIFOSIZ_TXFSTADDR(tmp);
+
+	fifo_size |= (fifo_0_start + (dwc->last_fifo_depth << 16));
+	if (dwc3_is_usb31(dwc))
+		dwc->last_fifo_depth += DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);
+	else
+		dwc->last_fifo_depth += DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);
+
+	/* Check fifo size allocation doesn't exceed available RAM size. */
+	if (dwc->last_fifo_depth >= ram1_depth) {
+		dev_err(dwc->dev, "Fifosize(%d) > RAM size(%d) %s depth:%d\n",
+				(dwc->last_fifo_depth * mdwidth), ram1_depth,
+				dep->endpoint.name, fifo_size);
+		if (dwc3_is_usb31(dwc))
+			fifo_size = DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);
+		else
+			fifo_size = DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);
+		dwc->last_fifo_depth -= fifo_size;
+		dep->fifo_depth = 0;
+		return -ENOMEM;
+	}
+
+	dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1), fifo_size);
+	dwc->num_ep_resized++;
+	return 0;
+}
+
 static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action)
 {
 	const struct usb_ss_ep_comp_descriptor *comp_desc;
@@ -620,6 +731,10 @@  static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)
 	int			ret;
 
 	if (!(dep->flags & DWC3_EP_ENABLED)) {
+		ret = dwc3_gadget_resize_tx_fifos(dep);
+		if (ret)
+			return ret;
+
 		ret = dwc3_gadget_start_config(dep);
 		if (ret)
 			return ret;