@@ -157,6 +157,14 @@ config MDIO_I2C
This is library mode.
+config MDIO_IPQ8064
+ tristate "Qualcomm IPQ8064 MDIO interface support"
+ depends on HAS_IOMEM && OF_MDIO
+ depends on MFD_SYSCON
+ help
+ This driver supports the MDIO interface found in the network
+ interface units of the IPQ8064 SoC
+
config MDIO_MOXART
tristate "MOXA ART MDIO interface support"
depends on ARCH_MOXART || COMPILE_TEST
@@ -36,6 +36,7 @@ obj-$(CONFIG_MDIO_CAVIUM) += mdio-cavium.o
obj-$(CONFIG_MDIO_GPIO) += mdio-gpio.o
obj-$(CONFIG_MDIO_HISI_FEMAC) += mdio-hisi-femac.o
obj-$(CONFIG_MDIO_I2C) += mdio-i2c.o
+obj-$(CONFIG_MDIO_IPQ8064) += mdio-ipq8064.o
obj-$(CONFIG_MDIO_MOXART) += mdio-moxart.o
obj-$(CONFIG_MDIO_MSCC_MIIM) += mdio-mscc-miim.o
obj-$(CONFIG_MDIO_OCTEON) += mdio-octeon.o
new file mode 100644
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Qualcomm IPQ8064 MDIO interface driver
+//
+// Copyright (C) 2019 Christian Lamparter <chunkeey@gmail.com>
+
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/of_mdio.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/syscon.h>
+
+/* MII address register definitions */
+#define MII_ADDR_REG_ADDR 0x10
+#define MII_BUSY BIT(0)
+#define MII_WRITE BIT(1)
+#define MII_CLKRANGE_60_100M (0 << 2)
+#define MII_CLKRANGE_100_150M (1 << 2)
+#define MII_CLKRANGE_20_35M (2 << 2)
+#define MII_CLKRANGE_35_60M (3 << 2)
+#define MII_CLKRANGE_150_250M (4 << 2)
+#define MII_CLKRANGE_250_300M (5 << 2)
+#define MII_CLKRANGE_MASK GENMASK(4, 2)
+#define MII_REG_SHIFT 6
+#define MII_REG_MASK GENMASK(10, 6)
+#define MII_ADDR_SHIFT 11
+#define MII_ADDR_MASK GENMASK(15, 11)
+
+#define MII_DATA_REG_ADDR 0x14
+
+#define MII_MDIO_DELAY (1000)
+#define MII_MDIO_RETRY (10)
+
+struct ipq8064_mdio {
+ struct regmap *base; /* NSS_GMAC0_BASE */
+};
+
+static int
+ipq8064_mdio_wait_busy(struct ipq8064_mdio *priv)
+{
+ u32 busy;
+
+ return regmap_read_poll_timeout(priv->base, MII_ADDR_REG_ADDR, busy,
+ !(busy & MII_BUSY), MII_MDIO_DELAY,
+ MII_MDIO_RETRY * USEC_PER_MSEC);
+}
+
+static int
+ipq8064_mdio_read(struct mii_bus *bus, int phy_addr, int reg_offset)
+{
+ struct ipq8064_mdio *priv = bus->priv;
+ u32 miiaddr = MII_BUSY | MII_CLKRANGE_250_300M;
+ u32 ret_val;
+ int err;
+
+ /* Reject clause 45 */
+ if (reg_offset & MII_ADDR_C45)
+ return -EOPNOTSUPP;
+
+ miiaddr |= ((phy_addr << MII_ADDR_SHIFT) & MII_ADDR_MASK) |
+ ((reg_offset << MII_REG_SHIFT) & MII_REG_MASK);
+
+ regmap_write(priv->base, MII_ADDR_REG_ADDR, miiaddr);
+ usleep_range(10, 20);
+
+ err = ipq8064_mdio_wait_busy(priv);
+ if (err)
+ return err;
+
+ regmap_read(priv->base, MII_DATA_REG_ADDR, &ret_val);
+ return (int)ret_val;
+}
+
+static int
+ipq8064_mdio_write(struct mii_bus *bus, int phy_addr, int reg_offset, u16 data)
+{
+ struct ipq8064_mdio *priv = bus->priv;
+ u32 miiaddr = MII_WRITE | MII_BUSY | MII_CLKRANGE_250_300M;
+
+ /* Reject clause 45 */
+ if (reg_offset & MII_ADDR_C45)
+ return -EOPNOTSUPP;
+
+ regmap_write(priv->base, MII_DATA_REG_ADDR, data);
+
+ miiaddr |= ((phy_addr << MII_ADDR_SHIFT) & MII_ADDR_MASK) |
+ ((reg_offset << MII_REG_SHIFT) & MII_REG_MASK);
+
+ regmap_write(priv->base, MII_ADDR_REG_ADDR, miiaddr);
+ usleep_range(10, 20);
+
+ return ipq8064_mdio_wait_busy(priv);
+}
+
+static int
+ipq8064_mdio_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct ipq8064_mdio *priv;
+ struct mii_bus *bus;
+ int ret;
+
+ bus = devm_mdiobus_alloc_size(&pdev->dev, sizeof(*priv));
+ if (!bus)
+ return -ENOMEM;
+
+ bus->name = "ipq8064_mdio_bus";
+ bus->read = ipq8064_mdio_read;
+ bus->write = ipq8064_mdio_write;
+ snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
+ bus->parent = &pdev->dev;
+
+ priv = bus->priv;
+ priv->base = syscon_node_to_regmap(np);
+ if (IS_ERR(priv->base) && priv->base != ERR_PTR(-EPROBE_DEFER))
+ priv->base = syscon_regmap_lookup_by_phandle(np, "master");
+
+ if (priv->base == ERR_PTR(-EPROBE_DEFER)) {
+ return -EPROBE_DEFER;
+ } else if (IS_ERR(priv->base)) {
+ dev_err(&pdev->dev, "error getting syscon regmap, error=%ld\n",
+ PTR_ERR(priv->base));
+ return PTR_ERR(priv->base);
+ }
+
+ ret = of_mdiobus_register(bus, np);
+ if (ret)
+ return ret;
+
+ platform_set_drvdata(pdev, bus);
+ return 0;
+}
+
+static int
+ipq8064_mdio_remove(struct platform_device *pdev)
+{
+ struct mii_bus *bus = platform_get_drvdata(pdev);
+
+ mdiobus_unregister(bus);
+
+ return 0;
+}
+
+static const struct of_device_id ipq8064_mdio_dt_ids[] = {
+ { .compatible = "qcom,ipq8064-mdio" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, ipq8064_mdio_dt_ids);
+
+static struct platform_driver ipq8064_mdio_driver = {
+ .probe = ipq8064_mdio_probe,
+ .remove = ipq8064_mdio_remove,
+ .driver = {
+ .name = "ipq8064-mdio",
+ .of_match_table = ipq8064_mdio_dt_ids,
+ },
+};
+
+module_platform_driver(ipq8064_mdio_driver);
+
+MODULE_DESCRIPTION("Qualcomm IPQ8064 MDIO interface driver");
+MODULE_AUTHOR("Christian Lamparter <chunkeey@gmail.com>");
+MODULE_LICENSE("GPL");
Currently ipq806x soc use generi bitbang driver to comunicate with the gmac ethernet interface. Add a dedicated driver created by chunkeey to fix this. Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> --- drivers/net/phy/Kconfig | 8 ++ drivers/net/phy/Makefile | 1 + drivers/net/phy/mdio-ipq8064.c | 166 +++++++++++++++++++++++++++++++++ 3 files changed, 175 insertions(+) create mode 100644 drivers/net/phy/mdio-ipq8064.c