diff mbox series

[v6,18/18] arm64: dts: qcom: qcs404-evb: Enable USB controllers

Message ID 20200210120723.91794-19-bryan.odonoghue@linaro.org
State New
Headers show
Series None | expand

Commit Message

Bryan O'Donoghue Feb. 10, 2020, 12:07 p.m. UTC 
This patch enables the primary and secondary USB controllers on the
qcs404-evb.

Primary:
The primary USB controller has

- One USB3 SS PHY using gpio-usb-conn
- One USB2 HS PHY in device mode only and no connector driver
  associated.

Secondary:
The second DWC3 controller which has one USB Hi-Speed PHY attached to it.

Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 40 ++++++++++++++++++++++++
 1 file changed, 40 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index 0fff50f755ef..4045d3000da6 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -318,6 +318,46 @@  pinconf {
 	};
 };
 
+&usb2 {
+	status = "okay";
+};
+
+&usb2_phy_sec {
+	vdd-supply = <&vreg_l4_1p2>;
+	vdda1p8-supply = <&vreg_l5_1p8>;
+	vdda3p3-supply = <&vreg_l12_3p3>;
+	status = "okay";
+};
+
+&usb3 {
+	status = "okay";
+	dwc3@7580000 {
+		usb-role-switch;
+		usb_con: connector {
+			compatible = "gpio-usb-b-connector";
+			label = "USB-C";
+			id-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+			vbus-supply = <&usb3_vbus_reg>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb3_id_pin>, <&usb3_vbus_pin>;
+			status = "okay";
+		};
+	};
+};
+
+&usb2_phy_prim {
+	vdd-supply = <&vreg_l4_1p2>;
+	vdda1p8-supply = <&vreg_l5_1p8>;
+	vdda3p3-supply = <&vreg_l12_3p3>;
+	status = "okay";
+};
+
+&usb3_phy {
+	vdd-supply = <&vreg_l3_1p05>;
+	vdda1p8-supply = <&vreg_l5_1p8>;
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	vdd-0.8-cx-mx-supply = <&vreg_l2_1p275>;