@@ -16,6 +16,9 @@ Optional properties:
- vcc-supply: phandle to the regulator that provides power to the PHY.
+- vbus-supply: phandle to the regulator that provides the VBUS power for when
+ the device is in HOST mode.
+
- reset-gpios: Should specify the GPIO for reset.
- vbus-detect-gpio: should specify the GPIO detecting a VBus insertion
@@ -203,13 +203,45 @@ static int nop_set_host(struct usb_otg *otg, struct usb_bus *host)
return 0;
}
+static int nop_set_vbus(struct usb_otg *otg, bool enabled)
+{
+ struct usb_phy_generic *nop;
+ int ret;
+
+ if (!otg)
+ return -ENODEV;
+
+ nop = container_of(otg->usb_phy, struct usb_phy_generic, phy);
+
+ if (!nop->vbus_reg)
+ return 0;
+
+ if (enabled) {
+ if (nop->vbus_reg_enabled)
+ return 0;
+ ret = regulator_enable(nop->vbus_reg);
+ if (ret < 0)
+ return ret;
+ nop->vbus_reg_enabled = true;
+ } else {
+ if (!nop->vbus_reg_enabled)
+ return 0;
+ ret = regulator_disable(nop->vbus_reg);
+ if (ret < 0)
+ return ret;
+ nop->vbus_reg_enabled = false;
+ }
+
+ return 0;
+}
+
int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop)
{
enum usb_phy_type type = USB_PHY_TYPE_USB2;
int err = 0;
u32 clk_rate = 0;
- bool needs_vcc = false, needs_clk = false;
+ bool needs_vcc = false, needs_clk = false, needs_vbus = false;
if (dev->of_node) {
struct device_node *node = dev->of_node;
@@ -219,6 +251,7 @@ int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop)
needs_vcc = of_property_read_bool(node, "vcc-supply");
needs_clk = of_property_read_bool(node, "clocks");
+ needs_vbus = of_property_read_bool(node, "vbus-supply");
}
nop->gpiod_reset = devm_gpiod_get_optional(dev, "reset",
GPIOD_ASIS);
@@ -268,6 +301,16 @@ int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop)
return -EPROBE_DEFER;
}
+ nop->vbus_reg = devm_regulator_get(dev, "vbus");
+ if (IS_ERR(nop->vbus_reg)) {
+ dev_dbg(dev, "Error getting vbus regulator: %ld\n",
+ PTR_ERR(nop->vbus_reg));
+ if (needs_vbus)
+ return -EPROBE_DEFER;
+
+ nop->vbus_reg = NULL;
+ }
+
nop->dev = dev;
nop->phy.dev = nop->dev;
nop->phy.label = "nop-xceiv";
@@ -278,6 +321,7 @@ int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop)
nop->phy.otg->usb_phy = &nop->phy;
nop->phy.otg->set_host = nop_set_host;
nop->phy.otg->set_peripheral = nop_set_peripheral;
+ nop->phy.otg->set_vbus = nop_set_vbus;
return 0;
}
@@ -14,7 +14,9 @@ struct usb_phy_generic {
struct gpio_desc *gpiod_reset;
struct gpio_desc *gpiod_vbus;
struct regulator *vbus_draw;
+ struct regulator *vbus_reg;
bool vbus_draw_enabled;
+ bool vbus_reg_enabled;
unsigned long mA;
unsigned int vbus;
};
This enables support for VBUS on boards where the power is supplied by a regulator. The regulator is enabled when the USB port enters HOST mode. Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> --- v2: Added missing "return 0;" in set_vbus method .../devicetree/bindings/usb/usb-nop-xceiv.txt | 3 ++ drivers/usb/phy/phy-generic.c | 46 ++++++++++++++++++- drivers/usb/phy/phy-generic.h | 2 + 3 files changed, 50 insertions(+), 1 deletion(-)