@@ -215,6 +215,67 @@
};
};
+ /* Settings for all SPI default and sleep states */
+ spi2 {
+ spi2_default_mode: spi_default {
+ default_mux {
+ ste,function = "spi2";
+ ste,pins = "spi2_oc1_2";
+ };
+ default_cfg1 {
+ ste,pins = "GPIO216_AG12"; /* FRM */
+ ste,config = <&gpio_out_hi>;
+ };
+ default_cfg2 {
+ ste,pins = "GPIO218_AH11"; /* RXD */
+ ste,config = <&in_pd>;
+ };
+ default_cfg3 {
+ ste,pins =
+ "GPIO215_AH13", /* TXD */
+ "GPIO217_AH12"; /* CLK */
+ ste,config = <&out_lo>;
+ };
+ };
+
+ spi2_idle_mode: spi_idle {
+ /*
+ * The idle mode is basically sleep mode sans wakeups. Also
+ * note that we have muxes the pins off the function here
+ * as we do not state any muxing.
+ */
+ idle_cfg1 {
+ ste,pins = "GPIO218_AH11"; /* RXD */
+ ste,config = <&slpm_in_pdis>;
+ };
+ idle_cfg2 {
+ ste,pins = "GPIO215_AH13"; /* TXD */
+ ste,config = <&slpm_out_lo_pdis>;
+ };
+ idle_cfg3 {
+ ste,pins = "GPIO217_AH12"; /* CLK */
+ ste,config = <&slpm_pdis>;
+ };
+ };
+
+ spi2_sleep_mode: spi_sleep {
+ sleep_cfg1 {
+ ste,pins =
+ "GPIO216_AG12", /* FRM */
+ "GPIO218_AH11"; /* RXD */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ sleep_cfg2 {
+ ste,pins = "GPIO215_AH13"; /* TXD */
+ ste,config = <&slpm_out_lo_wkup_pdis>;
+ };
+ sleep_cfg3 {
+ ste,pins = "GPIO217_AH12"; /* CLK */
+ ste,config = <&slpm_wkup_pdis>;
+ };
+ };
+ };
+
/* Settings for all MMC/SD/SDIO default and sleep states */
sdi0 {
/* This is the external SD card slot, 4 bits wide */
@@ -51,6 +51,15 @@
};
};
+ ssp@80002000 {
+ /*
+ * On the first generation boards, this SSP/SPI port was connected
+ * to the AB8500.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ssp0_hrefprev60_mode>;
+ };
+
vmmci: regulator-gpio {
gpios = <&tc3589x_gpio 18 0x4>;
enable-gpio = <&tc3589x_gpio 17 0x4>;
@@ -59,6 +68,19 @@
};
pinctrl {
+ ssp0 {
+ ssp0_hrefprev60_mode: ssp0_hrefprev60_default {
+ hrefprev60_mux {
+ ste,function = "ssp0";
+ ste,pins = "ssp0_a_1";
+ };
+ hrefprev60_cfg1 {
+ ste,pins = "GPIO145_C13"; /* RXD */
+ ste,config = <&in_pd>;
+ };
+
+ };
+ };
sdi0 {
/* This additional pin needed on early MOP500 and HREFs previous to v60 */
sdi0_default_mode: sdi0_default {
@@ -41,6 +41,23 @@
ste,output = <OUTPUT_LOW>;
};
+ gpio_out_hi: gpio_output_high {
+ ste,gpio = <GPIOMODE_ENABLED>;
+ ste,output = <OUTPUT_HIGH>;
+ };
+
+ slpm_pdis: slpm_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
+ slpm_wkup_pdis: slpm_wkup_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
slpm_wkup_pdis_en: slpm_wkup_pdis_en {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
@@ -53,6 +70,13 @@
ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
};
+ slpm_in_pdis: slpm_in_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-input = <SLPM_DIR_INPUT>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
slpm_in_wkup_pdis: slpm_in_wkup_pdis {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-input = <SLPM_DIR_INPUT>;
@@ -86,6 +110,13 @@
ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
};
+ slpm_out_lo_pdis: slpm_out_lo_pdis {
+ ste,sleep = <SLPM_ENABLED>;
+ ste,sleep-output = <SLPM_OUTPUT_LOW>;
+ ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+ ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+ };
+
slpm_out_lo_wkup_pdis: slpm_out_lo_wkup_pdis {
ste,sleep = <SLPM_ENABLED>;
ste,sleep-output = <SLPM_OUTPUT_LOW>;
@@ -342,22 +342,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
/* LCD VSI1 sleep state */
DB8500_PIN_SLEEP("GPIO69_E2", slpm_in_wkup_pdis, "0-0070"),
- /* Mux in SPI2 pins on the "other C1" altfunction */
- DB8500_MUX("spi2_oc1_2", "spi2", "spi2"),
- DB8500_PIN("GPIO216_AG12", gpio_out_hi, "spi2"), /* FRM */
- DB8500_PIN("GPIO218_AH11", in_pd, "spi2"), /* RXD */
- DB8500_PIN("GPIO215_AH13", out_lo, "spi2"), /* TXD */
- DB8500_PIN("GPIO217_AH12", out_lo, "spi2"), /* CLK */
- /* SPI2 idle state */
- DB8500_PIN_IDLE("GPIO218_AH11", slpm_in_wkup_pdis, "spi2"), /* RXD */
- DB8500_PIN_IDLE("GPIO215_AH13", slpm_out_lo_wkup_pdis, "spi2"), /* TXD */
- DB8500_PIN_IDLE("GPIO217_AH12", slpm_wkup_pdis, "spi2"), /* CLK */
- /* SPI2 sleep state */
- DB8500_PIN_SLEEP("GPIO216_AG12", slpm_in_wkup_pdis, "spi2"), /* FRM */
- DB8500_PIN_SLEEP("GPIO218_AH11", slpm_in_wkup_pdis, "spi2"), /* RXD */
- DB8500_PIN_SLEEP("GPIO215_AH13", slpm_out_lo_wkup_pdis, "spi2"), /* TXD */
- DB8500_PIN_SLEEP("GPIO217_AH12", slpm_wkup_pdis, "spi2"), /* CLK */
-
/* ske default state */
DB8500_MUX("kp_a_2", "kp", "nmk-ske-keypad"),
DB8500_PIN("GPIO153_B17", in_pd, "nmk-ske-keypad"), /* I7 */
@@ -582,9 +566,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
* on-chip pins as the HREFv60 and later does.
*/
static struct pinctrl_map __initdata mop500_pinmap[] = {
- /* Mux in SSP0, pull down RXD pin */
- DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
- DB8500_PIN_HOG("GPIO145_C13", pd),
/*
* XENON Flashgun on image processor GPIO (controlled from image
* processor firmware), mux in these image processor GPIO lines 0
This moves the SPI pin control table out of the board file and into the device tree. Move the specific setting for SSP0 on the HREFprev60 into the prev60-specific DTS file. The SPI2 configuration is not really connected to any device, as it will conflict with GPIO218 which is used on all HREFs. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 61 ++++++++++++++++++++++++++ arch/arm/boot/dts/ste-hrefprev60.dtsi | 22 ++++++++++ arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi | 31 +++++++++++++ arch/arm/mach-ux500/board-mop500-pins.c | 19 -------- 4 files changed, 114 insertions(+), 19 deletions(-)