@@ -57,6 +57,49 @@ static struct seq_rw_config default_write_configs[] = {
{0x00, 0, 0, 0, 0, 0x00, 0, 0},
};
+/*
+ * [N25Qxxx] Configuration
+ */
+#define N25Q_VCR_DUMMY_CYCLES(x) (((x) & 0xf) << 4)
+#define N25Q_VCR_XIP_DISABLED ((uint8_t)0x1 << 3)
+#define N25Q_VCR_WRAP_CONT 0x3
+
+/* N25Q 3-byte Address READ configurations
+ * - 'FAST' variants configured for 8 dummy cycles.
+ *
+ * Note, the number of dummy cycles used for 'FAST' READ operations is
+ * configurable and would normally be tuned according to the READ command and
+ * operating frequency. However, this applies universally to all 'FAST' READ
+ * commands, including those used by the SPIBoot controller, and remains in
+ * force until the device is power-cycled. Since the SPIBoot controller is
+ * hard-wired to use 8 dummy cycles, we must configure the device to also use 8
+ * cycles.
+ */
+static struct seq_rw_config n25q_read3_configs[] = {
+ {FLASH_FLAG_READ_1_4_4, FLASH_CMD_READ_1_4_4, 0, 4, 4, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_1_4, FLASH_CMD_READ_1_1_4, 0, 1, 4, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_2_2, FLASH_CMD_READ_1_2_2, 0, 2, 2, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_1_2, FLASH_CMD_READ_1_1_2, 0, 1, 2, 0x00, 0, 8},
+ {FLASH_FLAG_READ_FAST, FLASH_CMD_READ_FAST, 0, 1, 1, 0x00, 0, 8},
+ {FLASH_FLAG_READ_WRITE, FLASH_CMD_READ, 0, 1, 1, 0x00, 0, 0},
+ {0x00, 0, 0, 0, 0, 0x00, 0, 0},
+};
+
+/* N25Q 4-byte Address READ configurations
+ * - use special 4-byte address READ commands (reduces overheads, and
+ * reduces risk of hitting watchdog reset issues).
+ * - 'FAST' variants configured for 8 dummy cycles (see note above.)
+ */
+static struct seq_rw_config n25q_read4_configs[] = {
+ {FLASH_FLAG_READ_1_4_4, FLASH_CMD_READ4_1_4_4, 0, 4, 4, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_1_4, FLASH_CMD_READ4_1_1_4, 0, 1, 4, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_2_2, FLASH_CMD_READ4_1_2_2, 0, 2, 2, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_1_2, FLASH_CMD_READ4_1_1_2, 0, 1, 2, 0x00, 0, 8},
+ {FLASH_FLAG_READ_FAST, FLASH_CMD_READ4_FAST, 0, 1, 1, 0x00, 0, 8},
+ {FLASH_FLAG_READ_WRITE, FLASH_CMD_READ4, 0, 1, 1, 0x00, 0, 0},
+ {0x00, 0, 0, 0, 0, 0x00, 0, 0},
+};
+
static struct stfsm_seq stfsm_seq_read_jedec = {
.data_size = TRANSFER_SIZE(8),
.seq_opc[0] = (SEQ_OPC_PADS_1 |
@@ -229,6 +229,15 @@
#define FLASH_CMD_READ4_1_1_4 0x6c
#define FLASH_CMD_READ4_1_4_4 0xec
+/*
+ * Flags to tweak operation of default read/write/erase routines
+ */
+#define CFG_READ_TOGGLE_32BIT_ADDR 0x00000001
+#define CFG_WRITE_TOGGLE_32BIT_ADDR 0x00000002
+#define CFG_WRITE_EX_32BIT_ADDR_DELAY 0x00000004
+#define CFG_ERASESEC_TOGGLE_32BIT_ADDR 0x00000008
+#define CFG_S25FL_CHECK_ERROR_FLAGS 0x00000010
+
struct stfsm {
struct device *dev;
void __iomem *base;
@@ -237,6 +246,7 @@ struct stfsm {
struct mutex lock;
struct flash_info *info;
+ uint32_t configuration;
uint32_t fifo_dir_delay;
bool booted_from_spi;
bool reset_signal;
The N25Qxxx Serial Flash devices required different sequence configurations depending on whether they're running in 24bit (3Byte) or 32bit (4Byte) mode. We provide those here. Signed-off-by: Lee Jones <lee.jones@linaro.org> --- drivers/mtd/devices/st_spi_fsm.c | 43 ++++++++++++++++++++++++++++++++++++++++ drivers/mtd/devices/st_spi_fsm.h | 10 ++++++++++ 2 files changed, 53 insertions(+)