@@ -21,6 +21,7 @@
#include <linux/property.h>
#include <linux/mfd/axp20x.h>
#include <linux/extcon.h>
+#include <linux/dmi.h>
#define PS_STAT_VBUS_TRIGGER BIT(0)
#define PS_STAT_BAT_CHRG_DIR BIT(2)
@@ -545,6 +546,49 @@ out:
return IRQ_HANDLED;
}
+/*
+ * The HP Pavilion x2 10 series comes in a number of variants:
+ * Bay Trail SoC + AXP288 PMIC, DMI_BOARD_NAME: "815D"
+ * Cherry Trail SoC + AXP288 PMIC, DMI_BOARD_NAME: "813E"
+ * Cherry Trail SoC + TI PMIC, DMI_BOARD_NAME: "827C" or "82F4"
+ *
+ * The variants with the AXP288 PMIC are all kinds of special:
+ *
+ * 1. All variants use a Type-C connector which the AXP288 does not support, so
+ * when using a Type-C charger it is not recognized. Unlike most AXP288 devices,
+ * this model actually has mostly working ACPI AC / Battery code, the ACPI code
+ * "solves" this by simply setting the input_current_limit to 3A.
+ * There are still some issues with the ACPI code, so we use this native driver,
+ * and to solve the charging not working (500mA is not enough) issue we hardcode
+ * the 3A input_current_limit like the ACPI code does.
+ *
+ * 2. If no charger is connected the machine boots with the vbus-path disabled.
+ * Normally this is done when a 5V boost converter is active to avoid the PMIC
+ * trying to charge from the 5V boost converter's output. This is done when
+ * an OTG host cable is inserted and the ID pin on the micro-B receptacle is
+ * pulled low and the ID pin has an ACPI event handler associated with it
+ * which re-enables the vbus-path when the ID pin is pulled high when the
+ * OTG host cable is removed. The Type-C connector has no ID pin, there is
+ * no ID pin handler and there appears to be no 5V boost converter, so we
+ * end up not charging because the vbus-path is disabled, until we unplug
+ * the charger which automatically clears the vbus-path disable bit and then
+ * on the second plug-in of the adapter we start charging. To solve the not
+ * charging on first charger plugin we unconditionally enable the vbus-path at
+ * probe on this model, which is safe since there is no 5V boost converter.
+ */
+static const struct dmi_system_id axp288_hp_x2_dmi_ids[] = {
+ {
+ /*
+ * Bay Trail model has "Hewlett-Packard" as sys_vendor, Cherry
+ * Trail model has "HP", so we only match on product_name.
+ */
+ .matches = {
+ DMI_MATCH(DMI_PRODUCT_NAME, "HP Pavilion x2 Detachable"),
+ },
+ },
+ {} /* Terminating entry */
+};
+
static void axp288_charger_extcon_evt_worker(struct work_struct *work)
{
struct axp288_chrg_info *info =
@@ -568,7 +612,11 @@ static void axp288_charger_extcon_evt_wo
}
/* Determine cable/charger type */
- if (extcon_get_state(edev, EXTCON_CHG_USB_SDP) > 0) {
+ if (dmi_check_system(axp288_hp_x2_dmi_ids)) {
+ /* See comment above axp288_hp_x2_dmi_ids declaration */
+ dev_dbg(&info->pdev->dev, "HP X2 with Type-C, setting inlmt to 3A\n");
+ current_limit = 3000000;
+ } else if (extcon_get_state(edev, EXTCON_CHG_USB_SDP) > 0) {
dev_dbg(&info->pdev->dev, "USB SDP charger is connected\n");
current_limit = 500000;
} else if (extcon_get_state(edev, EXTCON_CHG_USB_CDP) > 0) {
@@ -685,6 +733,13 @@ static int charger_init_hw_regs(struct a
return ret;
}
+ if (dmi_check_system(axp288_hp_x2_dmi_ids)) {
+ /* See comment above axp288_hp_x2_dmi_ids declaration */
+ ret = axp288_charger_vbus_path_select(info, true);
+ if (ret < 0)
+ return ret;
+ }
+
/* Read current charge voltage and current limit */
ret = regmap_read(info->regmap, AXP20X_CHRG_CTRL1, &val);
if (ret < 0) {