@@ -168,6 +168,8 @@ static struct variant_data variant_ux500 = {
.cmdreg_srsp = MCI_CPSM_RESPONSE,
.datalength_bits = 24,
.datactrl_blocksz = 11,
+ .datactrl_any_blocksz = true,
+ .dma_power_of_2 = true,
.datactrl_mask_sdio = MCI_DPSM_ST_SDIOEN,
.st_sdio = true,
.st_clkdiv = true,
@@ -201,6 +203,8 @@ static struct variant_data variant_ux500v2 = {
.datactrl_mask_ddrmode = MCI_DPSM_ST_DDRMODE,
.datalength_bits = 24,
.datactrl_blocksz = 11,
+ .datactrl_any_blocksz = true,
+ .dma_power_of_2 = true,
.datactrl_mask_sdio = MCI_DPSM_ST_SDIOEN,
.st_sdio = true,
.st_clkdiv = true,
@@ -260,6 +264,7 @@ static struct variant_data variant_stm32_sdmmc = {
.datacnt_useless = true,
.datalength_bits = 25,
.datactrl_blocksz = 14,
+ .datactrl_any_blocksz = true,
.stm32_idmabsize_mask = GENMASK(12, 5),
.init = sdmmc_variant_init,
};
@@ -279,6 +284,7 @@ static struct variant_data variant_qcom = {
.data_cmd_enable = MCI_CPSM_QCOM_DATCMD,
.datalength_bits = 24,
.datactrl_blocksz = 11,
+ .datactrl_any_blocksz = true,
.pwrreg_powerup = MCI_PWR_UP,
.f_max = 208000000,
.explicit_mclk_control = true,
@@ -447,10 +453,11 @@ void mmci_dma_setup(struct mmci_host *host)
static int mmci_validate_data(struct mmci_host *host,
struct mmc_data *data)
{
+ struct variant_data *variant = host->variant;
+
if (!data)
return 0;
-
- if (!is_power_of_2(data->blksz)) {
+ if (!is_power_of_2(data->blksz) && !variant->datactrl_any_blocksz) {
dev_err(mmc_dev(host->mmc),
"unsupported block size (%d bytes)\n", data->blksz);
return -EINVAL;
@@ -515,7 +522,9 @@ int mmci_dma_start(struct mmci_host *host, unsigned int datactrl)
"Submit MMCI DMA job, sglen %d blksz %04x blks %04x flags %08x\n",
data->sg_len, data->blksz, data->blocks, data->flags);
- host->ops->dma_start(host, &datactrl);
+ ret = host->ops->dma_start(host, &datactrl);
+ if (ret)
+ return ret;
/* Trigger the DMA transfer */
mmci_write_datactrlreg(host, datactrl);
@@ -822,6 +831,18 @@ static int _mmci_dmae_prep_data(struct mmci_host *host, struct mmc_data *data,
if (data->blksz * data->blocks <= variant->fifosize)
return -EINVAL;
+ /*
+ * This is necessary to get SDIO working on the Ux500. We do not yet
+ * know if this is a bug in:
+ * - The Ux500 DMA controller (DMA40)
+ * - The MMCI DMA interface on the Ux500
+ * some power of two blocks (such as 64 bytes) are sent regularly
+ * during SDIO traffic and those work fine so for these we enable DMA
+ * transfers.
+ */
+ if (host->variant->dma_power_of_2 && !is_power_of_2(data->blksz))
+ return -EINVAL;
+
device = chan->device;
nr_sg = dma_map_sg(device->dev, data->sg, data->sg_len,
mmc_get_dma_dir(data));
@@ -872,9 +893,14 @@ int mmci_dmae_prep_data(struct mmci_host *host,
int mmci_dmae_start(struct mmci_host *host, unsigned int *datactrl)
{
struct mmci_dmae_priv *dmae = host->dma_priv;
+ int ret;
host->dma_in_progress = true;
- dmaengine_submit(dmae->desc_current);
+ ret = dma_submit_error(dmaengine_submit(dmae->desc_current));
+ if (ret < 0) {
+ host->dma_in_progress = false;
+ return ret;
+ }
dma_async_issue_pending(dmae->cur);
*datactrl |= MCI_DPSM_DMAENABLE;
@@ -278,7 +278,11 @@ struct mmci_host;
* @stm32_clkdiv: true if using a STM32-specific clock divider algorithm
* @datactrl_mask_ddrmode: ddr mode mask in datactrl register.
* @datactrl_mask_sdio: SDIO enable mask in datactrl register
- * @datactrl_blksz: block size in power of two
+ * @datactrl_blocksz: block size in power of two
+ * @datactrl_any_blocksz: true if block any block sizes are accepted by
+ * hardware, such as with some SDIO traffic that send
+ * odd packets.
+ * @dma_power_of_2: DMA only works with blocks that are a power of 2.
* @datactrl_first: true if data must be setup before send command
* @datacnt_useless: true if you could not use datacnt register to read
* remaining data
@@ -323,6 +327,8 @@ struct variant_data {
unsigned int datactrl_mask_ddrmode;
unsigned int datactrl_mask_sdio;
unsigned int datactrl_blocksz;
+ u8 datactrl_any_blocksz:1;
+ u8 dma_power_of_2:1;
u8 datactrl_first:1;
u8 datacnt_useless:1;
u8 st_sdio:1;