[3/4] mx6sabresd: Convert ethernet to driver model

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: Alifer Moraes <alifer.wsdm at gmail.com>
---
 board/freescale/mx6sabresd/mx6sabresd.c | 29 -------------------------
 configs/mx6sabresd_defconfig            |  5 +++++
 include/configs/mx6sabresd.h            |  9 --------
 3 files changed, 5 insertions(+), 38 deletions(-)

diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 4a208277ac..4b0af86f0b 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -21,7 +21,6 @@ 
 #include <mmc.h>
 #include <fsl_esdhc_imx.h>
 #include <miiphy.h>
-#include <netdev.h>
 #include <asm/arch/mxc_hdmi.h>
 #include <asm/arch/crm_regs.h>
 #include <asm/io.h>
@@ -44,9 +43,6 @@  DECLARE_GLOBAL_DATA_PTR;
 	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
 	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
 
-#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
-	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
 #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
 		      PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
 
@@ -73,31 +69,6 @@  static iomux_v3_cfg_t const uart1_pads[] = {
 	IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
 };
 
-static iomux_v3_cfg_t const enet_pads[] = {
-	IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_ENET_MDC__ENET_MDC	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	/* AR8031 PHY Reset */
-	IOMUX_PADS(PAD_ENET_CRS_DV__GPIO1_IO25	| MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-static void setup_iomux_enet(void)
-{
-	SETUP_IOMUX_PADS(enet_pads);
-}
-
 static iomux_v3_cfg_t const usdhc2_pads[] = {
 	IOMUX_PADS(PAD_SD2_CLK__SD2_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 	IOMUX_PADS(PAD_SD2_CMD__SD2_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
diff --git a/configs/mx6sabresd_defconfig b/configs/mx6sabresd_defconfig
index e3b8908928..05428a142c 100644
--- a/configs/mx6sabresd_defconfig
+++ b/configs/mx6sabresd_defconfig
@@ -81,6 +81,11 @@  CONFIG_SF_DEFAULT_MODE=0
 CONFIG_SF_DEFAULT_SPEED=20000000
 CONFIG_SPI_FLASH_STMICRO=y
 CONFIG_PHYLIB=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_FEC_MXC=y
+CONFIG_RGMII=y
 CONFIG_MII=y
 CONFIG_PCI=y
 CONFIG_DM_PCI=y
diff --git a/include/configs/mx6sabresd.h b/include/configs/mx6sabresd.h
index d810202117..ec1537541a 100644
--- a/include/configs/mx6sabresd.h
+++ b/include/configs/mx6sabresd.h
@@ -62,13 +62,4 @@ 
 #define CONFIG_USB_MAX_CONTROLLER_COUNT	1 /* Enabled USB controller number */
 #endif
 
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE			ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE		RGMII
-#define CONFIG_ETHPRIME			"FEC"
-#define CONFIG_FEC_MXC_PHYADDR		1
-
-#define CONFIG_PHY_ATHEROS
-
-
 #endif                         /* __MX6SABRESD_CONFIG_H */