diff mbox series

[PATCHv5,3/3] spi: Convert CONFIG_DM_SPI* to CONFIG_$(SPL_TPL_)DM_SPI*

Message ID 20200604151153.3980-4-Zhiqiang.Hou@nxp.com
State New
Headers show
Series spi: Split CONFIG_DM_SPI* to CONFIG_{SPL_TPL}DM_SPI* | expand

Commit Message

Zhiqiang Hou June 4, 2020, 3:11 p.m. UTC 
From: Lukasz Majewski <lukma at denx.de>

This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.

Before this change it was necessary to use:
    /* SPI Flash Configs */
    #if defined(CONFIG_SPL_BUILD)
    #undef CONFIG_DM_SPI
    #undef CONFIG_DM_SPI_FLASH
    #undef CONFIG_SPI_FLASH_MTD
    #endif

in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.

The goal of this patch:

Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.

Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).

In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):

- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
  run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
  environment with no fitImage and OF_LIBFDT support).

Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.

This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.

Signed-off-by: Lukasz Majewski <lukma at denx.de>
Tested-by: Adam Ford <aford173 at gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou at nxp.com>
---
V5:
 - No change.

 arch/arm/Kconfig                            | 11 +++++++++++
 board/l+g/vinco/vinco.c                     |  4 ++--
 cmd/sf.c                                    |  4 ++--
 cmd/spi.c                                   |  6 +++---
 common/spl/Kconfig                          | 20 ++++++++++++++++++++
 configs/am57xx_evm_defconfig                |  2 ++
 configs/am57xx_hs_evm_defconfig             |  2 ++
 configs/am57xx_hs_evm_usb_defconfig         |  2 ++
 configs/axm_defconfig                       |  2 ++
 configs/chromebook_link64_defconfig         |  2 ++
 configs/chromebook_samus_tpl_defconfig      |  4 ++++
 configs/dra7xx_evm_defconfig                |  2 ++
 configs/dra7xx_hs_evm_defconfig             |  2 ++
 configs/dra7xx_hs_evm_usb_defconfig         |  2 ++
 configs/j721e_evm_a72_defconfig             |  2 ++
 configs/j721e_evm_r5_defconfig              |  2 ++
 configs/ls1021aiot_qspi_defconfig           |  2 ++
 configs/ls1021aiot_sdcard_defconfig         |  2 ++
 configs/ls1021aqds_qspi_defconfig           |  1 +
 configs/ls1021aqds_sdcard_qspi_defconfig    |  1 +
 configs/ls1021atwr_qspi_defconfig           |  1 +
 configs/sama5d2_xplained_spiflash_defconfig |  2 ++
 configs/sama5d3xek_spiflash_defconfig       |  7 ++++---
 configs/sama5d4_xplained_spiflash_defconfig |  2 ++
 configs/sama5d4ek_spiflash_defconfig        |  2 ++
 configs/stm32mp15_basic_defconfig           |  2 ++
 configs/taurus_defconfig                    |  2 ++
 drivers/mtd/spi/Makefile                    |  4 ++--
 drivers/mtd/spi/sf_probe.c                  |  2 +-
 drivers/net/fm/fm.c                         |  4 ++--
 drivers/spi/Makefile                        |  2 +-
 drivers/spi/atmel_spi.c                     |  4 ++--
 drivers/spi/davinci_spi.c                   |  6 +++---
 drivers/spi/fsl_dspi.c                      |  5 +++--
 drivers/spi/kirkwood_spi.c                  |  2 +-
 drivers/spi/mxc_spi.c                       |  6 +++---
 drivers/spi/omap3_spi.c                     |  4 ++--
 drivers/spi/sh_qspi.c                       |  4 ++--
 env/sf.c                                    |  2 +-
 include/spi.h                               |  8 ++++----
 include/spi_flash.h                         |  2 +-
 test/dm/spi.c                               |  2 +-
 42 files changed, 112 insertions(+), 38 deletions(-)

Comments

Tom Rini June 30, 2020, 3:16 p.m. UTC | #1 
On Thu, Jun 04, 2020 at 11:11:53PM +0800, Zhiqiang Hou wrote:

> From: Lukasz Majewski <lukma at denx.de>
> 
> This change allows more fine tuning of driver model based SPI support in
> SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
> support in SPL and TPL via Kconfig option.
> 
> Before this change it was necessary to use:
>     /* SPI Flash Configs */
>     #if defined(CONFIG_SPL_BUILD)
>     #undef CONFIG_DM_SPI
>     #undef CONFIG_DM_SPI_FLASH
>     #undef CONFIG_SPI_FLASH_MTD
>     #endif
> 
> in the ./include/configs/<board>.h, which is error prone and shall be
> avoided when we strive to switch to Kconfig.
> 
> The goal of this patch:
> 
> Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
> Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
> still support non DM driver.
> 
> Another use case is the conversion of non DM/DTS SPI driver to support
> DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
> distinction is needed in Kconfig (also if SPL version of the driver
> supports OF_PLATDATA).
> 
> In the end of the day one would have to support following use cases (in
> single driver file - e.g. mxs_spi.c):
> 
> - U-Boot proper driver supporting DT/DTS
> - U-Boot proper driver without DT/DTS support (deprecated)
> - SPL driver without DT/DTS support
> - SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
>   run full blown DT/DTS)
> - SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
>   environment with no fitImage and OF_LIBFDT support).
> 
> Some boards do require SPI support (with DM) in SPL (TPL) and some only
> have DM_SPI{_FLASH} defined to allow compiling SPL.
> 
> This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
> and provides corresponding defines in Kconfig.
> 
> Signed-off-by: Lukasz Majewski <lukma at denx.de>
> Tested-by: Adam Ford <aford173 at gmail.com> #da850-evm
> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou at nxp.com>

Applied to u-boot/master, thanks!
diff mbox series

Patch

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 9c528eaec5..bac392c4cb 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -549,6 +549,7 @@  config TARGET_GPLUGD
 config ARCH_DAVINCI
 	bool "TI DaVinci"
 	select CPU_ARM926EJS
+	select SPL_DM_SPI if SPL
 	imply CMD_SAVES
 	help
 	  Support for TI's DaVinci platform.
@@ -566,6 +567,8 @@  config ARCH_MVEBU
 	select DM_SERIAL
 	select DM_SPI
 	select DM_SPI_FLASH
+	select SPL_DM_SPI if SPL
+	select SPL_DM_SPI_FLASH if SPL
 	select OF_CONTROL
 	select OF_SEPARATE
 	select SPI
@@ -985,6 +988,8 @@  config ARCH_SOCFPGA
 	imply FAT_WRITE
 	imply SPL
 	imply SPL_DM
+	imply SPL_DM_SPI
+	imply SPL_DM_SPI_FLASH
 	imply SPL_LIBDISK_SUPPORT
 	imply SPL_MMC_SUPPORT
 	imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
@@ -1093,6 +1098,8 @@  config ARCH_ZYNQ
 	select SPL_BOARD_INIT if SPL
 	select SPL_CLK if SPL
 	select SPL_DM if SPL
+	select SPL_DM_SPI if SPL
+	select SPL_DM_SPI_FLASH if SPL
 	select SPL_OF_CONTROL if SPL
 	select SPL_SEPARATE_BSS if SPL
 	select SUPPORT_SPL
@@ -1131,6 +1138,8 @@  config ARCH_ZYNQMP
 	select OF_CONTROL
 	select SPL_BOARD_INIT if SPL
 	select SPL_CLK if SPL
+	select SPL_DM_SPI if SPI
+	select SPL_DM_SPI_FLASH if SPL_DM_SPI
 	select SPL_DM_MAILBOX if SPL
 	select SPL_FIRMWARE if SPL
 	select SPL_SEPARATE_BSS if SPL
@@ -1688,6 +1697,8 @@  config ARCH_ROCKCHIP
 	select OF_CONTROL
 	select SPI
 	select SPL_DM if SPL
+	select SPL_DM_SPI if SPL
+	select SPL_DM_SPI_FLASH if SPL
 	select SYS_MALLOC_F
 	select SYS_THUMB_BUILD if !ARM64
 	imply ADC
diff --git a/board/l+g/vinco/vinco.c b/board/l+g/vinco/vinco.c
index 5a998e37d8..440838c112 100644
--- a/board/l+g/vinco/vinco.c
+++ b/board/l+g/vinco/vinco.c
@@ -34,7 +34,7 @@ 
 DECLARE_GLOBAL_DATA_PTR;
 
 /* FIXME gpio code here need to handle through DM_GPIO */
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 int spi_cs_is_valid(unsigned int bus, unsigned int cs)
 {
 	return bus == 0 && cs == 0;
@@ -167,7 +167,7 @@  int board_init(void)
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 	vinco_spi0_hw_init();
 #endif
 
diff --git a/cmd/sf.c b/cmd/sf.c
index 727837d9cd..66ea43a44f 100644
--- a/cmd/sf.c
+++ b/cmd/sf.c
@@ -91,7 +91,7 @@  static int do_spi_flash_probe(int argc, char *const argv[])
 	unsigned int speed = CONFIG_SF_DEFAULT_SPEED;
 	unsigned int mode = CONFIG_SF_DEFAULT_MODE;
 	char *endp;
-#ifdef CONFIG_DM_SPI_FLASH
+#if CONFIG_IS_ENABLED(DM_SPI_FLASH)
 	struct udevice *new, *bus_dev;
 	int ret;
 #else
@@ -124,7 +124,7 @@  static int do_spi_flash_probe(int argc, char *const argv[])
 			return -1;
 	}
 
-#ifdef CONFIG_DM_SPI_FLASH
+#if CONFIG_IS_ENABLED(DM_SPI_FLASH)
 	/* Remove the old device, otherwise probe will just be a nop */
 	ret = spi_find_bus_and_cs(bus, cs, &bus_dev, &new);
 	if (!ret) {
diff --git a/cmd/spi.c b/cmd/spi.c
index aec912167c..4aea191412 100644
--- a/cmd/spi.c
+++ b/cmd/spi.c
@@ -38,7 +38,7 @@  static int do_spi_xfer(int bus, int cs)
 	struct spi_slave *slave;
 	int ret = 0;
 
-#ifdef CONFIG_DM_SPI
+#if CONFIG_IS_ENABLED(DM_SPI)
 	char name[30], *str;
 	struct udevice *dev;
 
@@ -63,7 +63,7 @@  static int do_spi_xfer(int bus, int cs)
 		goto done;
 	ret = spi_xfer(slave, bitlen, dout, din,
 		       SPI_XFER_BEGIN | SPI_XFER_END);
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 	/* We don't get an error code in this case */
 	if (ret)
 		ret = -EIO;
@@ -79,7 +79,7 @@  static int do_spi_xfer(int bus, int cs)
 	}
 done:
 	spi_release_bus(slave);
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 	spi_free_slave(slave);
 #endif
 
diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index 414b6f396d..58b74ab74e 100644
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -739,6 +739,11 @@  config SPL_DM_SPI
 	help
 	  Enable support for SPI DM drivers in SPL.
 
+config SPL_DM_SPI_FLASH
+	bool "Support SPI DM FLASH drivers in SPL"
+	help
+	  Enable support for SPI DM flash drivers in SPL.
+
 endif
 if SPL_UBI
 config SPL_UBI_LOAD_BY_VOLNAME
@@ -1075,6 +1080,11 @@  config SPL_SPI_FLASH_SFDP_SUPPORT
 	 SPI NOR flashes using Serial Flash Discoverable Parameters (SFDP)
 	 tables as per JESD216 standard in SPL.
 
+config SPL_SPI_FLASH_MTD
+	bool "Support for SPI flash MTD drivers in SPL"
+	help
+	  Enable support for SPI flash MTD drivers in SPL.
+
 config SPL_SPI_LOAD
 	bool "Support loading from SPI flash"
 	help
@@ -1482,6 +1492,16 @@  config TPL_SPI_SUPPORT
 	  Enable support for using SPI in TPL. See SPL_SPI_SUPPORT for
 	  details.
 
+config TPL_DM_SPI
+	bool "Support SPI DM drivers in TPL"
+	help
+	  Enable support for SPI DM drivers in TPL.
+
+config TPL_DM_SPI_FLASH
+	bool "Support SPI DM FLASH drivers in TPL"
+	help
+	  Enable support for SPI DM flash drivers in TPL.
+
 config TPL_YMODEM_SUPPORT
 	bool "Support loading using Ymodem"
 	depends on TPL_SERIAL_SUPPORT
diff --git a/configs/am57xx_evm_defconfig b/configs/am57xx_evm_defconfig
index 42942e9ed4..47c94ce73b 100644
--- a/configs/am57xx_evm_defconfig
+++ b/configs/am57xx_evm_defconfig
@@ -76,6 +76,7 @@  CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_MMC_OMAP_HS=y
 CONFIG_MTD=y
 CONFIG_DM_SPI_FLASH=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SF_DEFAULT_MODE=0
 CONFIG_SF_DEFAULT_SPEED=76800000
 CONFIG_SPI_FLASH_SPANSION=y
@@ -94,6 +95,7 @@  CONFIG_DM_SCSI=y
 CONFIG_DM_SERIAL=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_TI_QSPI=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
diff --git a/configs/am57xx_hs_evm_defconfig b/configs/am57xx_hs_evm_defconfig
index f80ec38004..5c8c5d53cf 100644
--- a/configs/am57xx_hs_evm_defconfig
+++ b/configs/am57xx_hs_evm_defconfig
@@ -72,6 +72,7 @@  CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_MMC_OMAP_HS=y
 CONFIG_MTD=y
 CONFIG_DM_SPI_FLASH=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SF_DEFAULT_MODE=0
 CONFIG_SF_DEFAULT_SPEED=76800000
 CONFIG_SPI_FLASH_SPANSION=y
@@ -90,6 +91,7 @@  CONFIG_DM_SCSI=y
 CONFIG_DM_SERIAL=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_TI_QSPI=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
diff --git a/configs/am57xx_hs_evm_usb_defconfig b/configs/am57xx_hs_evm_usb_defconfig
index 3b155cc202..0a1bcfd41f 100644
--- a/configs/am57xx_hs_evm_usb_defconfig
+++ b/configs/am57xx_hs_evm_usb_defconfig
@@ -78,6 +78,7 @@  CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_MMC_OMAP_HS=y
 CONFIG_MTD=y
 CONFIG_DM_SPI_FLASH=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SF_DEFAULT_MODE=0
 CONFIG_SF_DEFAULT_SPEED=76800000
 CONFIG_SPI_FLASH_BAR=y
@@ -97,6 +98,7 @@  CONFIG_DM_REGULATOR_PALMAS=y
 CONFIG_DM_SERIAL=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_TI_QSPI=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
diff --git a/configs/axm_defconfig b/configs/axm_defconfig
index 1ae78463d4..bbf98b0b04 100644
--- a/configs/axm_defconfig
+++ b/configs/axm_defconfig
@@ -63,6 +63,8 @@  CONFIG_MTD=y
 CONFIG_MTD_RAW_NAND=y
 # CONFIG_SYS_NAND_USE_FLASH_BBT is not set
 CONFIG_NAND_ATMEL=y
+CONFIG_SPL_DM_SPI=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_STMICRO=y
 CONFIG_PHYLIB=y
diff --git a/configs/chromebook_link64_defconfig b/configs/chromebook_link64_defconfig
index a13f6eac80..b3f7a215d9 100644
--- a/configs/chromebook_link64_defconfig
+++ b/configs/chromebook_link64_defconfig
@@ -30,6 +30,8 @@  CONFIG_SPL_SYS_MALLOC_SIMPLE=y
 CONFIG_SPL_CPU_SUPPORT=y
 CONFIG_SPL_ENV_SUPPORT=y
 CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_DM_SPI=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SPL_NET_SUPPORT=y
 CONFIG_SPL_PCI=y
 CONFIG_SPL_PCH_SUPPORT=y
diff --git a/configs/chromebook_samus_tpl_defconfig b/configs/chromebook_samus_tpl_defconfig
index a12a04b0bf..0a514517ea 100644
--- a/configs/chromebook_samus_tpl_defconfig
+++ b/configs/chromebook_samus_tpl_defconfig
@@ -31,11 +31,15 @@  CONFIG_BLOBLIST_SIZE=0x1000
 CONFIG_BLOBLIST_ADDR=0xff7c0000
 CONFIG_HANDOFF=y
 CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SPL_DM_SPI=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SPL_NET_SUPPORT=y
 CONFIG_SPL_PCI=y
 CONFIG_SPL_PCH_SUPPORT=y
 CONFIG_TPL_PCI=y
 CONFIG_TPL_PCH_SUPPORT=y
+CONFIG_TPL_DM_SPI=y
+CONFIG_TPL_DM_SPI_FLASH=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_CPU=y
 CONFIG_CMD_GPIO=y
diff --git a/configs/dra7xx_evm_defconfig b/configs/dra7xx_evm_defconfig
index e4547d9dcc..019fe0d217 100644
--- a/configs/dra7xx_evm_defconfig
+++ b/configs/dra7xx_evm_defconfig
@@ -83,6 +83,7 @@  CONFIG_MTD=y
 CONFIG_MTD_RAW_NAND=y
 CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
 CONFIG_DM_SPI_FLASH=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SF_DEFAULT_MODE=0
 CONFIG_SF_DEFAULT_SPEED=76800000
 CONFIG_SPI_FLASH_SPANSION=y
@@ -105,6 +106,7 @@  CONFIG_DM_SCSI=y
 CONFIG_DM_SERIAL=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_TI_QSPI=y
 CONFIG_TIMER=y
 CONFIG_OMAP_TIMER=y
diff --git a/configs/dra7xx_hs_evm_defconfig b/configs/dra7xx_hs_evm_defconfig
index c08bcce903..e14d4186ff 100644
--- a/configs/dra7xx_hs_evm_defconfig
+++ b/configs/dra7xx_hs_evm_defconfig
@@ -86,6 +86,7 @@  CONFIG_MTD=y
 CONFIG_MTD_RAW_NAND=y
 CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
 CONFIG_DM_SPI_FLASH=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SF_DEFAULT_MODE=0
 CONFIG_SF_DEFAULT_SPEED=76800000
 CONFIG_SPI_FLASH_SPANSION=y
@@ -108,6 +109,7 @@  CONFIG_DM_SCSI=y
 CONFIG_DM_SERIAL=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_TI_QSPI=y
 CONFIG_TIMER=y
 CONFIG_OMAP_TIMER=y
diff --git a/configs/dra7xx_hs_evm_usb_defconfig b/configs/dra7xx_hs_evm_usb_defconfig
index 879c2b650b..7bb1cbb7af 100644
--- a/configs/dra7xx_hs_evm_usb_defconfig
+++ b/configs/dra7xx_hs_evm_usb_defconfig
@@ -83,6 +83,7 @@  CONFIG_SPL_MMC_HS200_SUPPORT=y
 CONFIG_MMC_OMAP_HS=y
 CONFIG_MTD=y
 CONFIG_DM_SPI_FLASH=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SF_DEFAULT_MODE=0
 CONFIG_SF_DEFAULT_SPEED=76800000
 CONFIG_SPI_FLASH_BAR=y
@@ -105,6 +106,7 @@  CONFIG_DM_SCSI=y
 CONFIG_DM_SERIAL=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_TI_QSPI=y
 CONFIG_TIMER=y
 CONFIG_OMAP_TIMER=y
diff --git a/configs/j721e_evm_a72_defconfig b/configs/j721e_evm_a72_defconfig
index 4deb4e219f..175fdbaeca 100644
--- a/configs/j721e_evm_a72_defconfig
+++ b/configs/j721e_evm_a72_defconfig
@@ -120,6 +120,7 @@  CONFIG_FLASH_CFI_MTD=y
 CONFIG_SYS_FLASH_CFI=y
 CONFIG_HBMC_AM654=y
 CONFIG_DM_SPI_FLASH=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_STMICRO=y
 # CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
 CONFIG_SPI_FLASH_MTD=y
@@ -146,6 +147,7 @@  CONFIG_DM_SERIAL=y
 CONFIG_SOC_TI=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_CADENCE_QSPI=y
 CONFIG_SYSRESET=y
 CONFIG_SPL_SYSRESET=y
diff --git a/configs/j721e_evm_r5_defconfig b/configs/j721e_evm_r5_defconfig
index ee9217aee2..60ad84ae38 100644
--- a/configs/j721e_evm_r5_defconfig
+++ b/configs/j721e_evm_r5_defconfig
@@ -89,6 +89,7 @@  CONFIG_SPL_MMC_SDHCI_ADMA=y
 CONFIG_MMC_SDHCI_AM654=y
 CONFIG_MTD=y
 CONFIG_DM_SPI_FLASH=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_SFDP_SUPPORT=y
 CONFIG_SPI_FLASH_STMICRO=y
 CONFIG_PINCTRL=y
@@ -112,6 +113,7 @@  CONFIG_DM_SERIAL=y
 CONFIG_SOC_TI=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_CADENCE_QSPI=y
 CONFIG_SYSRESET=y
 CONFIG_SPL_SYSRESET=y
diff --git a/configs/ls1021aiot_qspi_defconfig b/configs/ls1021aiot_qspi_defconfig
index cb73a04b35..5f576b4255 100644
--- a/configs/ls1021aiot_qspi_defconfig
+++ b/configs/ls1021aiot_qspi_defconfig
@@ -17,6 +17,7 @@  CONFIG_CMD_DHCP=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
+CONFIG_CMD_SF=y
 CONFIG_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="ls1021a-iot-duart"
 CONFIG_ENV_IS_IN_SPI_FLASH=y
@@ -44,6 +45,7 @@  CONFIG_DM_SCSI=y
 CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_FSL_DSPI=y
 CONFIG_FSL_QSPI=y
 CONFIG_USB=y
diff --git a/configs/ls1021aiot_sdcard_defconfig b/configs/ls1021aiot_sdcard_defconfig
index 10b6930914..c2c24c39a4 100644
--- a/configs/ls1021aiot_sdcard_defconfig
+++ b/configs/ls1021aiot_sdcard_defconfig
@@ -22,6 +22,7 @@  CONFIG_CMD_DHCP=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
+CONFIG_CMD_SF=y
 # CONFIG_SPL_EFI_PARTITION is not set
 CONFIG_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="ls1021a-iot-duart"
@@ -50,6 +51,7 @@  CONFIG_DM_SCSI=y
 CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_FSL_DSPI=y
 CONFIG_FSL_QSPI=y
 CONFIG_USB=y
diff --git a/configs/ls1021aqds_qspi_defconfig b/configs/ls1021aqds_qspi_defconfig
index f91534cfdd..0542c5c303 100644
--- a/configs/ls1021aqds_qspi_defconfig
+++ b/configs/ls1021aqds_qspi_defconfig
@@ -64,6 +64,7 @@  CONFIG_DM_SCSI=y
 CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_FSL_DSPI=y
 CONFIG_FSL_QSPI=y
 CONFIG_USB=y
diff --git a/configs/ls1021aqds_sdcard_qspi_defconfig b/configs/ls1021aqds_sdcard_qspi_defconfig
index 9871c8edf4..fd49917505 100644
--- a/configs/ls1021aqds_sdcard_qspi_defconfig
+++ b/configs/ls1021aqds_sdcard_qspi_defconfig
@@ -76,6 +76,7 @@  CONFIG_DM_SCSI=y
 CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPIy=y
 CONFIG_FSL_DSPI=y
 CONFIG_FSL_QSPI=y
 CONFIG_USB=y
diff --git a/configs/ls1021atwr_qspi_defconfig b/configs/ls1021atwr_qspi_defconfig
index 4c82d66899..8ef0589334 100644
--- a/configs/ls1021atwr_qspi_defconfig
+++ b/configs/ls1021atwr_qspi_defconfig
@@ -62,6 +62,7 @@  CONFIG_DM_SCSI=y
 CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPI_DM_SPI=y
 CONFIG_FSL_DSPI=y
 CONFIG_FSL_QSPI=y
 CONFIG_USB=y
diff --git a/configs/sama5d2_xplained_spiflash_defconfig b/configs/sama5d2_xplained_spiflash_defconfig
index 43d493bf9c..377d6a32d0 100644
--- a/configs/sama5d2_xplained_spiflash_defconfig
+++ b/configs/sama5d2_xplained_spiflash_defconfig
@@ -66,6 +66,8 @@  CONFIG_DM_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ATMEL=y
 CONFIG_MTD=y
+CONFIG_SPL_DM_SPI=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SF_DEFAULT_SPEED=30000000
 CONFIG_SPI_FLASH_ATMEL=y
diff --git a/configs/sama5d3xek_spiflash_defconfig b/configs/sama5d3xek_spiflash_defconfig
index 6a76d7c9c0..47615464a5 100644
--- a/configs/sama5d3xek_spiflash_defconfig
+++ b/configs/sama5d3xek_spiflash_defconfig
@@ -8,12 +8,12 @@  CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x6000
 CONFIG_ENV_SECT_SIZE=0x1000
-CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
-CONFIG_DM_GPIO=y
+CONFIG_ENV_OFFSET=0x6000
 CONFIG_SPL_SERIAL_SUPPORT=y
 CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
+CONFIG_DM_GPIO=y
 CONFIG_NR_DRAM_BANKS=1
 CONFIG_SPL=y
 CONFIG_DEBUG_UART_BOARD_INIT=y
@@ -22,6 +22,7 @@  CONFIG_DEBUG_UART_CLOCK=132000000
 CONFIG_SPL_SPI_FLASH_SUPPORT=y
 CONFIG_SPL_SPI_SUPPORT=y
 CONFIG_SPL_TEXT_BASE=0x300000
+CONFIG_SPL_DM_SPI=y
 CONFIG_DEBUG_UART=y
 CONFIG_ENV_VARS_UBOOT_CONFIG=y
 CONFIG_FIT=y
diff --git a/configs/sama5d4_xplained_spiflash_defconfig b/configs/sama5d4_xplained_spiflash_defconfig
index 3be18e65a4..8c43fc785b 100644
--- a/configs/sama5d4_xplained_spiflash_defconfig
+++ b/configs/sama5d4_xplained_spiflash_defconfig
@@ -67,6 +67,7 @@  CONFIG_MTD_RAW_NAND=y
 # CONFIG_SYS_NAND_USE_FLASH_BBT is not set
 CONFIG_NAND_ATMEL=y
 CONFIG_DM_SPI_FLASH=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SF_DEFAULT_SPEED=30000000
 CONFIG_SPI_FLASH_ATMEL=y
 CONFIG_DM_ETH=y
@@ -80,6 +81,7 @@  CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_ATMEL_USART=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_TIMER=y
 CONFIG_SPL_TIMER=y
 CONFIG_ATMEL_PIT_TIMER=y
diff --git a/configs/sama5d4ek_spiflash_defconfig b/configs/sama5d4ek_spiflash_defconfig
index a7541a22d6..a4addddffb 100644
--- a/configs/sama5d4ek_spiflash_defconfig
+++ b/configs/sama5d4ek_spiflash_defconfig
@@ -64,6 +64,7 @@  CONFIG_MTD_RAW_NAND=y
 # CONFIG_SYS_NAND_USE_FLASH_BBT is not set
 CONFIG_NAND_ATMEL=y
 CONFIG_DM_SPI_FLASH=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SF_DEFAULT_SPEED=30000000
 CONFIG_SPI_FLASH_ATMEL=y
 CONFIG_DM_ETH=y
@@ -77,6 +78,7 @@  CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_ATMEL_USART=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_TIMER=y
 CONFIG_SPL_TIMER=y
 CONFIG_ATMEL_PIT_TIMER=y
diff --git a/configs/stm32mp15_basic_defconfig b/configs/stm32mp15_basic_defconfig
index c7dd2926c9..87f15bd3db 100644
--- a/configs/stm32mp15_basic_defconfig
+++ b/configs/stm32mp15_basic_defconfig
@@ -90,6 +90,7 @@  CONFIG_MTD_RAW_NAND=y
 CONFIG_NAND_STM32_FMC2=y
 CONFIG_MTD_SPI_NAND=y
 CONFIG_DM_SPI_FLASH=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_MACRONIX=y
 CONFIG_SPI_FLASH_SPANSION=y
 CONFIG_SPI_FLASH_STMICRO=y
@@ -120,6 +121,7 @@  CONFIG_RTC_STM32=y
 CONFIG_SERIAL_RX_BUFFER=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_STM32_QSPI=y
 CONFIG_STM32_SPI=y
 CONFIG_USB=y
diff --git a/configs/taurus_defconfig b/configs/taurus_defconfig
index 19d85f9b5a..5149365617 100644
--- a/configs/taurus_defconfig
+++ b/configs/taurus_defconfig
@@ -71,6 +71,8 @@  CONFIG_MTD=y
 CONFIG_MTD_RAW_NAND=y
 # CONFIG_SYS_NAND_USE_FLASH_BBT is not set
 CONFIG_NAND_ATMEL=y
+CONFIG_SPL_DM_SPI=y
+CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_STMICRO=y
 CONFIG_PHYLIB=y
diff --git a/drivers/mtd/spi/Makefile b/drivers/mtd/spi/Makefile
index b5dfa300de..952fd1e45a 100644
--- a/drivers/mtd/spi/Makefile
+++ b/drivers/mtd/spi/Makefile
@@ -3,7 +3,7 @@ 
 # (C) Copyright 2006
 # Wolfgang Denk, DENX Software Engineering, wd at denx.de.
 
-obj-$(CONFIG_DM_SPI_FLASH) += sf-uclass.o
+obj-$(CONFIG_$(SPL_TPL_)DM_SPI_FLASH) += sf-uclass.o
 spi-nor-y := sf_probe.o spi-nor-ids.o
 
 ifdef CONFIG_SPL_BUILD
@@ -19,5 +19,5 @@  endif
 
 obj-$(CONFIG_SPI_FLASH) += spi-nor.o
 obj-$(CONFIG_SPI_FLASH_DATAFLASH) += sf_dataflash.o
-obj-$(CONFIG_$(SPL_)SPI_FLASH_MTD) += sf_mtd.o
+obj-$(CONFIG_$(SPL_TPL_)SPI_FLASH_MTD) += sf_mtd.o
 obj-$(CONFIG_SPI_FLASH_SANDBOX) += sandbox.o
diff --git a/drivers/mtd/spi/sf_probe.c b/drivers/mtd/spi/sf_probe.c
index c2e51f9c68..444770f3e5 100644
--- a/drivers/mtd/spi/sf_probe.c
+++ b/drivers/mtd/spi/sf_probe.c
@@ -54,7 +54,7 @@  err_read_id:
 	return ret;
 }
 
-#ifndef CONFIG_DM_SPI_FLASH
+#if !CONFIG_IS_ENABLED(DM_SPI_FLASH)
 struct spi_flash *spi_flash_probe(unsigned int busnum, unsigned int cs,
 				  unsigned int max_hz, unsigned int spi_mode)
 {
diff --git a/drivers/net/fm/fm.c b/drivers/net/fm/fm.c
index 8ab1816395..bbb1738c4b 100644
--- a/drivers/net/fm/fm.c
+++ b/drivers/net/fm/fm.c
@@ -383,7 +383,7 @@  int fm_init_common(int index, struct ccsr_fman *reg)
 		addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);
 		int ret = 0;
 
-#ifdef CONFIG_DM_SPI_FLASH
+#if CONFIG_IS_ENABLED(DM_SPI_FLASH)
 		struct udevice *new;
 
 		/* speed and mode will be read from DT */
@@ -470,7 +470,7 @@  int fm_init_common(int index, struct ccsr_fman *reg)
 	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);
 	int ret = 0;
 
-#ifdef CONFIG_DM_SPI_FLASH
+#if CONFIG_IS_ENABLED(DM_SPI_FLASH)
 	struct udevice *new;
 
 	/* speed and mode will be read from DT */
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 6441694c8d..11d8d22cef 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -4,7 +4,7 @@ 
 # Wolfgang Denk, DENX Software Engineering, wd at denx.de.
 
 # There are many options which enable SPI, so make this library available
-ifdef CONFIG_DM_SPI
+ifdef CONFIG_$(SPL_TPL_)DM_SPI
 obj-y += spi-uclass.o
 obj-$(CONFIG_SANDBOX) += spi-emul-uclass.o
 obj-$(CONFIG_SOFT_SPI) += soft_spi.o
diff --git a/drivers/spi/atmel_spi.c b/drivers/spi/atmel_spi.c
index f076e92a93..e2f2b3be44 100644
--- a/drivers/spi/atmel_spi.c
+++ b/drivers/spi/atmel_spi.c
@@ -14,7 +14,7 @@ 
 
 #include <asm/arch/clk.h>
 #include <asm/arch/hardware.h>
-#ifdef CONFIG_DM_SPI
+#if CONFIG_IS_ENABLED(DM_SPI)
 #include <asm/arch/at91_spi.h>
 #endif
 #if CONFIG_IS_ENABLED(DM_GPIO)
@@ -23,7 +23,7 @@ 
 
 #include "atmel_spi.h"
 
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 
 static int spi_has_wdrbt(struct atmel_spi_slave *slave)
 {
diff --git a/drivers/spi/davinci_spi.c b/drivers/spi/davinci_spi.c
index 97ac97b1a5..f619534764 100644
--- a/drivers/spi/davinci_spi.c
+++ b/drivers/spi/davinci_spi.c
@@ -55,7 +55,7 @@ 
 /* SPIDEF */
 #define SPIDEF_CSDEF0_MASK	BIT(0)
 
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 #define SPI0_BUS		0
 #define SPI0_BASE		CONFIG_SYS_SPI_BASE
 /*
@@ -122,7 +122,7 @@  struct davinci_spi_regs {
 
 /* davinci spi slave */
 struct davinci_spi_slave {
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 	struct spi_slave slave;
 #endif
 	struct davinci_spi_regs *regs;
@@ -346,7 +346,7 @@  out:
 	return 0;
 }
 
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 
 static inline struct davinci_spi_slave *to_davinci_spi(struct spi_slave *slave)
 {
diff --git a/drivers/spi/fsl_dspi.c b/drivers/spi/fsl_dspi.c
index 1cdb233110..d9575aaf54 100644
--- a/drivers/spi/fsl_dspi.c
+++ b/drivers/spi/fsl_dspi.c
@@ -100,7 +100,7 @@  struct fsl_dspi_priv {
 	struct dspi *regs;
 };
 
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 struct fsl_dspi {
 	struct spi_slave slave;
 	struct fsl_dspi_priv priv;
@@ -414,7 +414,8 @@  static int fsl_dspi_cfg_speed(struct fsl_dspi_priv *priv, uint speed)
 
 	return 0;
 }
-#ifndef CONFIG_DM_SPI
+
+#if !CONFIG_IS_ENABLED(DM_SPI)
 int spi_cs_is_valid(unsigned int bus, unsigned int cs)
 {
 	if (((cs >= 0) && (cs < 8)) && ((bus >= 0) && (bus < 8)))
diff --git a/drivers/spi/kirkwood_spi.c b/drivers/spi/kirkwood_spi.c
index 01fcf6bef5..60ca09f2ac 100644
--- a/drivers/spi/kirkwood_spi.c
+++ b/drivers/spi/kirkwood_spi.c
@@ -94,7 +94,7 @@  static int _spi_xfer(struct kwspi_registers *reg, unsigned int bitlen,
 	return 0;
 }
 
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 
 static struct kwspi_registers *spireg =
 	(struct kwspi_registers *)MVEBU_SPI_BASE;
diff --git a/drivers/spi/mxc_spi.c b/drivers/spi/mxc_spi.c
index f52ebf4d67..aad3780365 100644
--- a/drivers/spi/mxc_spi.c
+++ b/drivers/spi/mxc_spi.c
@@ -67,7 +67,7 @@  static inline struct mxc_spi_slave *to_mxc_spi_slave(struct spi_slave *slave)
 
 static void mxc_spi_cs_activate(struct mxc_spi_slave *mxcs)
 {
-#if defined(CONFIG_DM_SPI)
+#if CONFIG_IS_ENABLED(DM_SPI)
 	struct udevice *dev = mxcs->dev;
 	struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev);
 
@@ -85,7 +85,7 @@  static void mxc_spi_cs_activate(struct mxc_spi_slave *mxcs)
 
 static void mxc_spi_cs_deactivate(struct mxc_spi_slave *mxcs)
 {
-#if defined(CONFIG_DM_SPI)
+#if CONFIG_IS_ENABLED(DM_SPI)
 	struct udevice *dev = mxcs->dev;
 	struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev);
 
@@ -415,7 +415,7 @@  static int mxc_spi_claim_bus_internal(struct mxc_spi_slave *mxcs, int cs)
 	return 0;
 }
 
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
 		void *din, unsigned long flags)
 {
diff --git a/drivers/spi/omap3_spi.c b/drivers/spi/omap3_spi.c
index 6a615d1498..ae08531f1e 100644
--- a/drivers/spi/omap3_spi.c
+++ b/drivers/spi/omap3_spi.c
@@ -109,7 +109,7 @@  struct mcspi {
 };
 
 struct omap3_spi_priv {
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 	struct spi_slave slave;
 #endif
 	struct mcspi *regs;
@@ -455,7 +455,7 @@  static void _omap3_spi_claim_bus(struct omap3_spi_priv *priv)
 	writel(conf, &priv->regs->modulctrl);
 }
 
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 
 static inline struct omap3_spi_priv *to_omap3_spi(struct spi_slave *slave)
 {
diff --git a/drivers/spi/sh_qspi.c b/drivers/spi/sh_qspi.c
index 2839dd1ceb..aa1c03047e 100644
--- a/drivers/spi/sh_qspi.c
+++ b/drivers/spi/sh_qspi.c
@@ -68,7 +68,7 @@  struct sh_qspi_regs {
 };
 
 struct sh_qspi_slave {
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 	struct spi_slave	slave;
 #endif
 	struct sh_qspi_regs	*regs;
@@ -223,7 +223,7 @@  static int sh_qspi_xfer_common(struct sh_qspi_slave *ss, unsigned int bitlen,
 	return ret;
 }
 
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 static inline struct sh_qspi_slave *to_sh_qspi(struct spi_slave *slave)
 {
 	return container_of(slave, struct sh_qspi_slave, slave);
diff --git a/env/sf.c b/env/sf.c
index 23de5a3495..a4106807c7 100644
--- a/env/sf.c
+++ b/env/sf.c
@@ -38,7 +38,7 @@  static struct spi_flash *env_flash;
 
 static int setup_flash_device(void)
 {
-#ifdef CONFIG_DM_SPI_FLASH
+#if CONFIG_IS_ENABLED(DM_SPI_FLASH)
 	struct udevice *new;
 	int	ret;
 
diff --git a/include/spi.h b/include/spi.h
index 5cc6d6e008..9b4fb8dc0b 100644
--- a/include/spi.h
+++ b/include/spi.h
@@ -39,7 +39,7 @@ 
 
 #define SPI_DEFAULT_WORDLEN	8
 
-#ifdef CONFIG_DM_SPI
+#if CONFIG_IS_ENABLED(DM_SPI)
 /* TODO(sjg at chromium.org): Remove this and use max_hz from struct spi_slave */
 struct dm_spi_bus {
 	uint max_hz;
@@ -131,7 +131,7 @@  enum spi_polarity {
  * @flags:		Indication of SPI flags.
  */
 struct spi_slave {
-#ifdef CONFIG_DM_SPI
+#if CONFIG_IS_ENABLED(DM_SPI)
 	struct udevice *dev;	/* struct spi_slave is dev->parentdata */
 	uint max_hz;
 	uint speed;
@@ -317,7 +317,7 @@  void spi_flash_copy_mmap(void *data, void *offset, size_t len);
  */
 int spi_cs_is_valid(unsigned int bus, unsigned int cs);
 
-#ifndef CONFIG_DM_SPI
+#if !CONFIG_IS_ENABLED(DM_SPI)
 /**
  * Activate a SPI chipselect.
  * This function is provided by the board code when using a driver
@@ -367,7 +367,7 @@  static inline int spi_w8r8(struct spi_slave *slave, unsigned char byte)
 	return ret < 0 ? ret : din[1];
 }
 
-#ifdef CONFIG_DM_SPI
+#if CONFIG_IS_ENABLED(DM_SPI)
 
 /**
  * struct spi_cs_info - Information about a bus chip select
diff --git a/include/spi_flash.h b/include/spi_flash.h
index 0b23f57a71..e8348adec2 100644
--- a/include/spi_flash.h
+++ b/include/spi_flash.h
@@ -52,7 +52,7 @@  struct dm_spi_flash_ops {
 /* Access the serial operations for a device */
 #define sf_get_ops(dev) ((struct dm_spi_flash_ops *)(dev)->driver->ops)
 
-#ifdef CONFIG_DM_SPI_FLASH
+#if CONFIG_IS_ENABLED(DM_SPI_FLASH)
 /**
  * spi_flash_read_dm() - Read data from SPI flash
  *
diff --git a/test/dm/spi.c b/test/dm/spi.c
index 8e417acc5f..474008cde0 100644
--- a/test/dm/spi.c
+++ b/test/dm/spi.c
@@ -117,7 +117,7 @@  static int dm_test_spi_xfer(struct unit_test_state *uts)
 	 * Since we are about to destroy all devices, we must tell sandbox
 	 * to forget the emulation device
 	 */
-#ifdef CONFIG_DM_SPI_FLASH
+#if CONFIG_IS_ENABLED(DM_SPI_FLASH)
 	sandbox_sf_unbind_emul(state_get_current(), busnum, cs);
 #endif