@@ -24,12 +24,6 @@ config TARGET_SOCRATES
bool "Support socrates"
select ARCH_MPC8544
-config TARGET_BSC9131RDB
- bool "Support BSC9131RDB"
- select ARCH_BSC9131
- select SUPPORT_SPL
- select BOARD_EARLY_INIT_F
-
config TARGET_BSC9132QDS
bool "Support BSC9132QDS"
select ARCH_BSC9132
@@ -1579,7 +1573,6 @@ config SYS_FSL_LBC_CLK_DIV
Defines divider of platform clock(clock input to
eLBC controller).
-source "board/freescale/bsc9131rdb/Kconfig"
source "board/freescale/bsc9132qds/Kconfig"
source "board/freescale/c29xpcie/Kconfig"
source "board/freescale/corenet_ds/Kconfig"
deleted file mode 100644
@@ -1,12 +0,0 @@
-if TARGET_BSC9131RDB
-
-config SYS_BOARD
- default "bsc9131rdb"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_CONFIG_NAME
- default "BSC9131RDB"
-
-endif
deleted file mode 100644
@@ -1,9 +0,0 @@
-BSC9131RDB BOARD
-M: Poonam Aggrwal <poonam.aggrwal at nxp.com>
-S: Maintained
-F: board/freescale/bsc9131rdb/
-F: include/configs/BSC9131RDB.h
-F: configs/BSC9131RDB_NAND_defconfig
-F: configs/BSC9131RDB_NAND_SYSCLK100_defconfig
-F: configs/BSC9131RDB_SPIFLASH_defconfig
-F: configs/BSC9131RDB_SPIFLASH_SYSCLK100_defconfig
deleted file mode 100644
@@ -1,21 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright 2011-2012 Freescale Semiconductor, Inc.
-
-MINIMAL=
-
-ifdef CONFIG_SPL_BUILD
-ifdef CONFIG_SPL_INIT_MINIMAL
-MINIMAL=y
-endif
-endif
-
-ifdef MINIMAL
-obj-y += spl_minimal.o
-else
-obj-y += bsc9131rdb.o
-obj-y += ddr.o
-endif
-
-obj-y += law.o
-obj-y += tlb.o
deleted file mode 100644
@@ -1,151 +0,0 @@
-Overview
---------
-- BSC9131 is integrated device that targets Femto base station market.
- It combines Power Architecture e500v2 and DSP StarCore SC3850 core
- technologies with MAPLE-B2F baseband acceleration processing elements.
-- It's MAPLE disabled personality is called 9231.
-
-The BSC9131 SoC includes the following function and features:
-. Power Architecture subsystem including a e500 processor with 256-Kbyte shared
- L2 cache
-. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
-. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
- Processing (MAPLE-B2F)
-. A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding,
- Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing,
- and CRC algorithms
-. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
- Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion
- operations
-. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with
- ECC, up to 400-MHz clock/800 MHz data rate
-. Dedicated security engine featuring trusted boot
-. DMA controller
-. OCNDMA with four bidirectional channels
-. Interfaces
-. Two triple-speed Gigabit Ethernet controllers featuring network acceleration
- including IEEE 1588. v2 hardware support and virtualization (eTSEC)
-. eTSEC 1 supports RGMII/RMII
-. eTSEC 2 supports RGMII
-. High-speed USB 2.0 host and device controller with ULPI interface
-. Enhanced secure digital (SD/MMC) host controller (eSDHC)
-. Antenna interface controller (AIC), supporting three industry standard
- JESD207/three custom ADI RF interfaces (two dual port and one single port)
- and three MAXIM's MaxPHY serial interfaces
-. ADI lanes support both full duplex FDD support and half duplex TDD support
-. Universal Subscriber Identity Module (USIM) interface that facilitates
- communication to SIM cards or Eurochip pre-paid phone cards
-. TDM with one TDM port
-. Two DUART, four eSPI, and two I2C controllers
-. Integrated Flash memory controller (IFC)
-. TDM with 256 channels
-. GPIO
-. Sixteen 32-bit timers
-
-The e500 core subsystem within the Power Architecture consists of the following:
-. 32-Kbyte L1 instruction cache
-. 32-Kbyte L1 data cache
-. 256-Kbyte L2 cache/L2 memory/L2 stash
-. programmable interrupt controller (PIC)
-. Debug support
-. Timers
-
-The SC3850 core subsystem consists of the following:
-. 32 Kbyte 8-way level 1 instruction cache (L1 ICache)
-. 32 Kbyte 8-way level 1 data cache (L1 DCache)
-. 512 Kbyte 8-way level 2 unified instruction/data cache (M2 memory)
-. Memory management unit (MMU)
-. Enhanced programmable interrupt controller (EPIC)
-. Debug and profiling unit (DPU)
-. Two 32-bit timers
-
-BSC9131RDB board Overview
--------------------------
- 1Gbyte DDR3 (on board DDR)
- 128Mbyte 2K page size NAND Flash
- 256 Kbit M24256 I2C EEPROM
- 128 Mbit SPI Flash memory
- USB-ULPI
- eTSEC1: Connected to RGMII PHY
- eTSEC2: Connected to RGMII PHY
- DUART interface: supports one UARTs up to 115200 bps for console display
- USIM connector
-
-Frequency Combinations Supported
---------------------------------
-Core MHz/CCB MHz/DDR(MT/s)
-1. 1000/500/800
-2. 800/400/667
-
-Boot Methods Supported
------------------------
-1. NAND Flash
-2. SPI Flash
-
-Default Boot Method
---------------------
-NAND boot
-
-Building U-Boot
---------------
-To build the U-Boot for BSC9131RDB:
-1. NAND Flash with sysclk 66MHz(J16 on RDB closed, default)
- make BSC9131RDB_NAND
-2. NAND Flash with sysclk 100MHz(J16 on RDB open)
- make BSC9131RDB_NAND_SYSCLK100
-3. SPI Flash with sysclk 66MHz(J16 on RDB closed, default)
- make BSC9131RDB_SPIFLASH
-4. SPI Flash with sysclk 100MHz(J16 on RDB open)
- make BSC9131RDB_SPIFLASH_SYSCLK100
-
-Memory map
------------
- 0x0000_0000 0x7FFF_FFFF DDR 1G cacheable
- 0xA0000000 0xBFFFFFFF Shared DSP core L2/M2 space 512M
- 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M
- 0xC1F0_0000 0xC1F3_FFFF PA SRAM Region 0 256K
- 0xC1F8_0000 0xC1F9_FFFF PA SRAM Region 1 128K
- 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K
- 0xFEE0_0000 0xFEE0_0FFF DSP Boot ROM 4K
- 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M
- 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M
- 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND Buffer 8M
-
-DDR Memory map
----------------
- 0x0000_0000 0x36FF_FFFF Memory passed onto Linux
- 0x3700_0000 0x37FF_FFFF PowerPC-DSP shared control area
- 0x3800_0000 0x4FFF_FFFF DSP Private area
-
- Out of 880M, passed onto Linux, 1hugetlb page of 256M is reserved for
- data communcation between PowerPC and DSP core.
- Rest is PowerPC private area.
-
-Flashing Images
----------------
-To place a new U-Boot image in the NAND flash and then boot
-with that new image temporarily, use this:
- tftp 1000000 u-boot-nand.bin
- nand erase 0 100000
- nand write 1000000 0 100000
- reset
-
-Using the Device Tree Source File
----------------------------------
-To create the DTB (Device Tree Binary) image file,
-use a command similar to this:
-
- dtc -b 0 -f -I dts -O dtb bsc9131rdb.dts > bsc9131rdb.dtb
-
-Likely, that .dts file will come from here;
-
- linux-2.6/arch/powerpc/boot/dts/bsc9131rdb.dts
-
-Booting Linux
--------------
-Place a linux uImage in the TFTP disk area.
-
- tftp 1000000 uImage
- tftp 2000000 rootfs.ext2.gz.uboot
- tftp c00000 bsc9131rdb.dtb
- bootm 1000000 2000000 c00000
deleted file mode 100644
@@ -1,82 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2011-2012 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <image.h>
-#include <init.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/cache.h>
-#include <asm/immap_85xx.h>
-#include <asm/io.h>
-#include <env.h>
-#include <miiphy.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <fsl_mdio.h>
-#include <tsec.h>
-#include <jffs2/load_kernel.h>
-#include <mtd_node.h>
-#include <flash.h>
-#include <netdev.h>
-
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
- ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
-
- clrbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_CTS_B0_GPIO42);
- setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_CTS_B0_DSP_TMS);
-
- clrbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_RTS_B0_GPIO43);
- setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_RTS_B0_DSP_TCK |
- MPC85xx_PMUXCR2_UART_CTS_B1_SIM_PD);
- setbits_be32(&gur->halt_req_mask, HALTED_TO_HALT_REQ_MASK_0);
- clrsetbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_IFC_AD_GPIO_MASK |
- MPC85xx_PMUXCR_IFC_AD17_GPO_MASK,
- MPC85xx_PMUXCR_IFC_AD_GPIO |
- MPC85xx_PMUXCR_IFC_AD17_GPO | MPC85xx_PMUXCR_SDHC_USIM);
-
- return 0;
-}
-
-int checkboard(void)
-{
- struct cpu_type *cpu;
-
- cpu = gd->arch.cpu;
- printf("Board: %sRDB\n", cpu->name);
-
- return 0;
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-#ifdef CONFIG_FDT_FIXUP_PARTITIONS
-static const struct node_info nodes[] = {
- { "fsl,ifc-nand", MTD_DEV_TYPE_NAND, },
-};
-#endif
-int ft_board_setup(void *blob, bd_t *bd)
-{
- phys_addr_t base;
- phys_size_t size;
-
- ft_cpu_setup(blob, bd);
-
- base = env_get_bootm_low();
- size = env_get_bootm_size();
-
- fdt_fixup_memory(blob, (u64)base, (u64)size);
-#ifdef CONFIG_FDT_FIXUP_PARTITIONS
- fdt_fixup_mtdparts(blob, nodes, ARRAY_SIZE(nodes));
-#endif
-
- fsl_fdt_fixup_dr_usb(blob, bd);
-
- return 0;
-}
-#endif
deleted file mode 100644
@@ -1,170 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2011-2012 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <init.h>
-#include <vsprintf.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <asm/processor.h>
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-#include <asm/io.h>
-#include <asm/fsl_law.h>
-
-#ifndef CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_SYS_DRAM_SIZE 1024
-
-fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = {
- .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
- .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
- .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
- .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_800,
- .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_800,
- .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_800,
- .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_800,
- .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL,
- .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2,
- .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_800,
- .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_800,
- .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
- .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_800,
- .ddr_data_init = CONFIG_MEM_INIT_VALUE,
- .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_800,
- .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
- .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
- .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
- .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
- .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL,
- .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL_800,
- .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR,
- .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
- .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
-};
-
-fixed_ddr_parm_t fixed_ddr_parm_0[] = {
- {750, 850, &ddr_cfg_regs_800},
- {0, 0, NULL}
-};
-
-unsigned long get_sdram_size(void)
-{
- return get_ram_size(CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DRAM_SIZE);
-}
-
-/*
- * Fixed sdram init -- doesn't use serial presence detect.
- */
-phys_size_t fixed_sdram(void)
-{
- int i;
- char buf[32];
- fsl_ddr_cfg_regs_t ddr_cfg_regs;
- phys_size_t ddr_size;
- ulong ddr_freq, ddr_freq_mhz;
-
- ddr_freq = get_ddr_freq(0);
- ddr_freq_mhz = ddr_freq / 1000000;
-
- printf("Configuring DDR for %s MT/s data rate\n",
- strmhz(buf, ddr_freq));
-
- for (i = 0; fixed_ddr_parm_0[i].max_freq > 0; i++) {
- if ((ddr_freq_mhz > fixed_ddr_parm_0[i].min_freq) &&
- (ddr_freq_mhz <= fixed_ddr_parm_0[i].max_freq)) {
- memcpy(&ddr_cfg_regs, fixed_ddr_parm_0[i].ddr_settings,
- sizeof(ddr_cfg_regs));
- break;
- }
- }
-
- if (fixed_ddr_parm_0[i].max_freq == 0) {
- panic("Unsupported DDR data rate %s MT/s data rate\n",
- strmhz(buf, ddr_freq));
- }
-
- ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
- fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0);
-
- if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, ddr_size,
- LAW_TRGT_IF_DDR_1) < 0) {
- printf("ERROR setting Local Access Windows for DDR\n");
- return 0;
- }
-
- return ddr_size;
-}
-
-#else /* CONFIG_SYS_DDR_RAW_TIMING */
-/* Micron MT41J256M8HX-15E */
-dimm_params_t ddr_raw_timing = {
- .n_ranks = 1,
- .rank_density = 1073741824u,
- .capacity = 1073741824u,
- .primary_sdram_width = 32,
- .ec_sdram_width = 0,
- .registered_dimm = 0,
- .mirrored_dimm = 0,
- .n_row_addr = 15,
- .n_col_addr = 10,
- .n_banks_per_sdram_device = 8,
- .edc_config = 0,
- .burst_lengths_bitmask = 0x0c,
-
- .tckmin_x_ps = 1870,
- .caslat_x = 0x1e << 4, /* 5,6,7,8 */
- .taa_ps = 13125,
- .twr_ps = 15000,
- .trcd_ps = 13125,
- .trrd_ps = 7500,
- .trp_ps = 13125,
- .tras_ps = 37500,
- .trc_ps = 50625,
- .trfc_ps = 160000,
- .twtr_ps = 7500,
- .trtp_ps = 7500,
- .refresh_rate_ps = 7800000,
- .tfaw_ps = 37500,
-};
-
-int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
- unsigned int controller_number,
- unsigned int dimm_number)
-{
- const char dimm_model[] = "Fixed DDR on board";
-
- if ((controller_number == 0) && (dimm_number == 0)) {
- memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
- memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
- memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
- }
-
- return 0;
-}
-
-void fsl_ddr_board_options(memctl_options_t *popts,
- dimm_params_t *pdimm,
- unsigned int ctrl_num)
-{
- int i;
- popts->clk_adjust = 6;
- popts->cpo_override = 0x1f;
- popts->write_data_delay = 2;
- popts->half_strength_driver_enable = 1;
- /* Write leveling override */
- popts->wrlvl_en = 1;
- popts->wrlvl_override = 1;
- popts->wrlvl_sample = 0xf;
- popts->wrlvl_start = 0x8;
- popts->trwt_override = 1;
- popts->trwt = 0;
-
- for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
- popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER;
- popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS;
- }
-}
-
-#endif /* CONFIG_SYS_DDR_RAW_TIMING */
deleted file mode 100644
@@ -1,18 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2011-2012 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-struct law_entry law_table[] = {
- SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC),
- SET_LAW(CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS, LAW_SIZE_1M,
- LAW_TRGT_IF_DSP_CCSR),
- SET_LAW(CONFIG_SYS_FSL_DSP_M2_RAM_ADDR, LAW_SIZE_16M,
- LAW_TRGT_IF_OCN_DSP),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
deleted file mode 100644
@@ -1,105 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2013 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <init.h>
-#include <ns16550.h>
-#include <asm/io.h>
-#include <nand.h>
-#include <linux/compiler.h>
-#include <asm/fsl_law.h>
-#include <fsl_ddr_sdram.h>
-#include <asm/global_data.h>
-#include <linux/delay.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * Fixed sdram init -- doesn't use serial presence detect.
- */
-static void sdram_init(void)
-{
- struct ccsr_ddr __iomem *ddr =
- (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
-
- __raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds);
- __raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config);
-#if CONFIG_CHIP_SELECTS_PER_CTRL > 1
- __raw_writel(CONFIG_SYS_DDR_CS1_BNDS, &ddr->cs1_bnds);
- __raw_writel(CONFIG_SYS_DDR_CS1_CONFIG, &ddr->cs1_config);
-#endif
- __raw_writel(CONFIG_SYS_DDR_TIMING_3_800, &ddr->timing_cfg_3);
- __raw_writel(CONFIG_SYS_DDR_TIMING_0_800, &ddr->timing_cfg_0);
- __raw_writel(CONFIG_SYS_DDR_TIMING_1_800, &ddr->timing_cfg_1);
- __raw_writel(CONFIG_SYS_DDR_TIMING_2_800, &ddr->timing_cfg_2);
-
- __raw_writel(CONFIG_SYS_DDR_CONTROL_2, &ddr->sdram_cfg_2);
- __raw_writel(CONFIG_SYS_DDR_MODE_1_800, &ddr->sdram_mode);
- __raw_writel(CONFIG_SYS_DDR_MODE_2_800, &ddr->sdram_mode_2);
-
- __raw_writel(CONFIG_SYS_DDR_INTERVAL_800, &ddr->sdram_interval);
- __raw_writel(CONFIG_SYS_DDR_DATA_INIT, &ddr->sdram_data_init);
- __raw_writel(CONFIG_SYS_DDR_CLK_CTRL_800, &ddr->sdram_clk_cntl);
-
- __raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL_800, &ddr->ddr_wrlvl_cntl);
- __raw_writel(CONFIG_SYS_DDR_TIMING_4, &ddr->timing_cfg_4);
- __raw_writel(CONFIG_SYS_DDR_TIMING_5, &ddr->timing_cfg_5);
- __raw_writel(CONFIG_SYS_DDR_ZQ_CONTROL, &ddr->ddr_zq_cntl);
-
- /* Set, but do not enable the memory */
- __raw_writel(CONFIG_SYS_DDR_CONTROL & ~SDRAM_CFG_MEM_EN, &ddr->sdram_cfg);
-
- asm volatile("sync;isync");
- udelay(500);
-
- /* Let the controller go */
- out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN);
-
- set_next_law(CONFIG_SYS_NAND_DDR_LAW, LAW_SIZE_1G, LAW_TRGT_IF_DDR_1);
-}
-
-void board_init_f(ulong bootflag)
-{
- u32 plat_ratio;
- ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
-
- /* initialize selected port with appropriate baud rate */
- plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
- plat_ratio >>= 1;
- gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
-
- NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
- gd->bus_clk / 16 / CONFIG_BAUDRATE);
-
- puts("\nNAND boot... ");
-
- /* Initialize the DDR3 */
- sdram_init();
-
- /* copy code to RAM and jump to it - this should not return */
- /* NOTE - code has to be copied out of NAND buffer before
- * other blocks can be read.
- */
- relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE);
-}
-
-void board_init_r(gd_t *gd, ulong dest_addr)
-{
- nand_boot();
-}
-
-void putc(char c)
-{
- if (c == '\n')
- NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
-
- NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
-}
-
-void puts(const char *str)
-{
- while (*str)
- putc(*str++);
-}
deleted file mode 100644
@@ -1,61 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2011-2012 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 ,
- CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 ,
- CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 ,
- CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
-
- /* TLB 1 */
- /* *I*** - Covers boot page */
- SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_4K, 1),
-#ifdef CONFIG_SPL_NAND_BOOT
- SET_TLB_ENTRY(1, 0xffffe000, 0xffffe000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 10, BOOKE_PAGESZ_4K, 1),
-#endif
-
- /* *I*G* - CCSRBAR (PA) */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_1M, 1),
-
- /* CCSRBAR (DSP) */
- SET_TLB_ENTRY(1, CONFIG_SYS_FSL_DSP_CCSRBAR,
- CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 2, BOOKE_PAGESZ_1M, 1),
-
-#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_SPL)
- SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
- 0, 8, BOOKE_PAGESZ_1G, 1),
-#endif
-
- SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_1M, 1)
-
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
deleted file mode 100644
@@ -1,64 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x00201000
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_OFFSET=0xE0000
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_TEXT_BASE=0xFFFFE000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_BSC9131RDB=y
-CONFIG_SYS_CUSTOM_LDSCRIPT=y
-CONFIG_SYS_LDSCRIPT="arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="SYS_CLK_100"
-CONFIG_BOOTDELAY=10
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-# CONFIG_MISC_INIT_R is not set
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_NAND_BOOT=y
-CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=ff800000.flash,"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=ff800000.flash:1m(uboot),8m(kernel),512k(dtb),-(fs)"
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_FSL_CAAM=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-# CONFIG_PCI is not set
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
-CONFIG_FDT_FIXUP_PARTITIONS=y
deleted file mode 100644
@@ -1,63 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x00201000
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_OFFSET=0xE0000
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_TEXT_BASE=0xFFFFE000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_BSC9131RDB=y
-CONFIG_SYS_CUSTOM_LDSCRIPT=y
-CONFIG_SYS_LDSCRIPT="arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-# CONFIG_MISC_INIT_R is not set
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_NAND_BOOT=y
-CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=ff800000.flash,"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=ff800000.flash:1m(uboot),8m(kernel),512k(dtb),-(fs)"
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_FSL_CAAM=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-# CONFIG_PCI is not set
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
-CONFIG_FDT_FIXUP_PARTITIONS=y
deleted file mode 100644
@@ -1,56 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x11000000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_BSC9131RDB=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="SPIFLASH,SYS_CLK_100"
-CONFIG_BOOTDELAY=10
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-# CONFIG_MISC_INIT_R is not set
-CONFIG_HUSH_PARSER=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=ff800000.flash,"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=ff800000.flash:1m(uboot),8m(kernel),512k(dtb),-(fs)"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_FSL_CAAM=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-# CONFIG_PCI is not set
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
-CONFIG_FDT_FIXUP_PARTITIONS=y
deleted file mode 100644
@@ -1,56 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x11000000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_BSC9131RDB=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="SPIFLASH"
-CONFIG_BOOTDELAY=10
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-# CONFIG_MISC_INIT_R is not set
-CONFIG_HUSH_PARSER=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=ff800000.flash,"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=ff800000.flash:1m(uboot),8m(kernel),512k(dtb),-(fs)"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_FSL_CAAM=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-# CONFIG_PCI is not set
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
-CONFIG_FDT_FIXUP_PARTITIONS=y
deleted file mode 100644
@@ -1,337 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2011-2012 Freescale Semiconductor, Inc.
- */
-
-/*
- * BSC9131 RDB board configuration file
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_NAND_FSL_IFC
-
-#ifdef CONFIG_SPIFLASH
-#define CONFIG_RAMBOOT_SPIFLASH
-#define CONFIG_SYS_RAMBOOT
-#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc
-#endif
-
-#ifdef CONFIG_MTD_RAW_NAND
-#define CONFIG_SPL_INIT_MINIMAL
-#define CONFIG_SPL_FLUSH_IMAGE
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-
-#define CONFIG_SPL_MAX_SIZE 8192
-#define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000
-#define CONFIG_SPL_RELOC_STACK 0x00100000
-#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) - 0x2000)
-#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE)
-#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0
-#endif
-
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
-#else
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#endif
-
-/* High Level Configuration Options */
-
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on 9131 RDB */
-#if defined(CONFIG_SYS_CLK_100)
-#define CONFIG_SYS_CLK_FREQ 100000000 /* SYSCLK for 9131 RDB */
-#else
-#define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for 9131 RDB */
-#endif
-
-#define CONFIG_HWCONFIG
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* enable branch predition */
-
-/* DDR Setup */
-#undef CONFIG_SYS_DDR_RAW_TIMING
-#undef CONFIG_DDR_SPD
-#define CONFIG_SYS_SPD_BUS_NUM 0
-#define SPD_EEPROM_ADDRESS 0x52 /* I2C access */
-
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_sdram_size(void);
-#endif
-#define CONFIG_SYS_SDRAM_SIZE get_sdram_size() /* DDR size */
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 1
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
-#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
-
-#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
-#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
-#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
-#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
-
-#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
-#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
-#define CONFIG_SYS_DDR_RCW_1 0x00000000
-#define CONFIG_SYS_DDR_RCW_2 0x00000000
-#define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */
-#define CONFIG_SYS_DDR_CONTROL_2 0x24401000
-#define CONFIG_SYS_DDR_TIMING_4 0x00000001
-#define CONFIG_SYS_DDR_TIMING_5 0x02401400
-
-#define CONFIG_SYS_DDR_TIMING_3_800 0x00030000
-#define CONFIG_SYS_DDR_TIMING_0_800 0x00110104
-#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b8644
-#define CONFIG_SYS_DDR_TIMING_2_800 0x0fa888cf
-#define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000
-#define CONFIG_SYS_DDR_MODE_1_800 0x00441420
-#define CONFIG_SYS_DDR_MODE_2_800 0x8000c000
-#define CONFIG_SYS_DDR_INTERVAL_800 0x0c300100
-#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8675f608
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR CONFIG_SYS_CCSRBAR_DEFAULT
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR_DEFAULT
-
-#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */
- /* CONFIG_SYS_IMMR */
-/* DSP CCSRBAR */
-#define CONFIG_SYS_FSL_DSP_CCSRBAR CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
-#define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
-
-/*
- * Memory map
- *
- * 0x0000_0000 0x3FFF_FFFF DDR 1G cacheable
- * 0x8800_0000 0x8810_0000 IFC internal SRAM 1M
- * 0xB000_0000 0xB0FF_FFFF DSP core M2 memory 16M
- * 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M
- * 0xC1F0_0000 0xC1F3_FFFF PA L2 SRAM Region 0 256K
- * 0xC1F8_0000 0xC1F9_FFFF PA L2 SRAM Region 1 128K
- * 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K
- * 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M
- * 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M
- * 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND flash buffer 8M
- *
- */
-
-/*
- * IFC Definitions
- */
-
-/* NAND Flash on IFC */
-#define CONFIG_SYS_NAND_BASE 0xff800000
-#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
-
-#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | CSPR_PORT_SIZE_8 /* Port Size = 8 bit*/ \
- | CSPR_MSEL_NAND /* MSEL = NAND */ \
- | CSPR_V)
-#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
-
-#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
- | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
- | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
- | CSOR_NAND_RAL_2 /* RAL = 2Byes */ \
- | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
- | CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \
- | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-
-/* NAND Flash Timing Params */
-#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x03) \
- | FTIM0_NAND_TWP(0x05) \
- | FTIM0_NAND_TWCHT(0x02) \
- | FTIM0_NAND_TWH(0x04))
-#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x1C) \
- | FTIM1_NAND_TWBE(0x1E) \
- | FTIM1_NAND_TRR(0x07) \
- | FTIM1_NAND_TRP(0x05))
-#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x08) \
- | FTIM2_NAND_TREH(0x04) \
- | FTIM2_NAND_TWHRE(0x11))
-#define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x04)
-
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-
-#define CONFIG_SYS_NAND_DDR_LAW 11
-
-/* Set up IFC registers for boot location NAND */
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
-
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* End of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
- - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/
-
-/* Serial Port */
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_NS16550_MIN_FUNCTIONS
-#endif
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-
-/* I2C EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
-
-/* eSPI - Enhanced SPI */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-
-#define TSEC1_PHY_ADDR 0
-#define TSEC2_PHY_ADDR 3
-
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX 0
-
-#define TSEC2_PHYIDX 0
-
-#define CONFIG_ETHPRIME "eTSEC1"
-
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-#if defined(CONFIG_RAMBOOT_SPIFLASH)
-#elif defined(CONFIG_MTD_RAW_NAND)
-#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
-#endif
-
-#define CONFIG_LOADS_ECHO /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-#ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_HAS_FSL_DR_USB
-#endif
-
-/*
- * Dynamic MTD Partition support with mtdparts
- */
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#endif
-
-#define CONFIG_HOSTNAME "BSC9131rdb"
-#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "uboot=" CONFIG_UBOOTPATH "\0" \
- "loadaddr=1000000\0" \
- "bootfile=uImage\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "ramdiskfile=rootfs.ext2.gz.uboot\0" \
- "fdtaddr=1e00000\0" \
- "fdtfile=bsc9131rdb.dtb\0" \
- "bdev=sda1\0" \
- "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \
- "bootm_size=0x37000000\0" \
- "othbootargs=ramdisk_size=600000 " \
- "default_hugepagesz=256m hugepagesz=256m hugepages=1\0" \
- "usbext2boot=setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs; " \
- "usb start;" \
- "ext2load usb 0:4 $loadaddr $bootfile;" \
- "ext2load usb 0:4 $fdtaddr $fdtfile;" \
- "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs; " \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
-
-#endif /* __CONFIG_H */