diff mbox series

[08/16] arm: Remove pcm058 board

Message ID 20200613135455.181483-9-jagan@amarulasolutions.com
State New
Headers show
Series spi: dm-conversion (part3) | expand

Commit Message

Jagan Teki June 13, 2020, 1:54 p.m. UTC
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.

Remove it.

Patch-cc: Stefano Babic <sbabic at denx.de>
Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
---
 arch/arm/mach-imx/mx6/Kconfig   |   6 -
 board/phytec/pcm058/Kconfig     |  12 -
 board/phytec/pcm058/MAINTAINERS |   6 -
 board/phytec/pcm058/Makefile    |   7 -
 board/phytec/pcm058/README      |  35 --
 board/phytec/pcm058/pcm058.c    | 571 --------------------------------
 configs/pcm058_defconfig        |  70 ----
 include/configs/pcm058.h        |  77 -----
 8 files changed, 784 deletions(-)
 delete mode 100644 board/phytec/pcm058/Kconfig
 delete mode 100644 board/phytec/pcm058/MAINTAINERS
 delete mode 100644 board/phytec/pcm058/Makefile
 delete mode 100644 board/phytec/pcm058/README
 delete mode 100644 board/phytec/pcm058/pcm058.c
 delete mode 100644 configs/pcm058_defconfig
 delete mode 100644 include/configs/pcm058.h
diff mbox series

Patch

diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index 9c9013bd92..30e29f680a 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -507,11 +507,6 @@  config TARGET_PLATINUM_TITANIUM
 	bool "platinum-titanium"
 	select SUPPORT_SPL
 
-config TARGET_PCM058
-	bool "Phytec PCM058 i.MX6 Quad"
-	select BOARD_LATE_INIT
-	select SUPPORT_SPL
-
 config TARGET_PCL063
 	bool "PHYTEC PCL063 (phyCORE-i.MX6UL)"
 	select MX6UL
@@ -708,7 +703,6 @@  source "board/freescale/mx6sxsabreauto/Kconfig"
 source "board/freescale/mx6ul_14x14_evk/Kconfig"
 source "board/freescale/mx6ullevk/Kconfig"
 source "board/grinn/liteboard/Kconfig"
-source "board/phytec/pcm058/Kconfig"
 source "board/phytec/pcl063/Kconfig"
 source "board/gateworks/gw_ventana/Kconfig"
 source "board/kosagi/novena/Kconfig"
diff --git a/board/phytec/pcm058/Kconfig b/board/phytec/pcm058/Kconfig
deleted file mode 100644
index d099275d48..0000000000
--- a/board/phytec/pcm058/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@ 
-if TARGET_PCM058
-
-config SYS_BOARD
-	default "pcm058"
-
-config SYS_VENDOR
-	default "phytec"
-
-config SYS_CONFIG_NAME
-	default "pcm058"
-
-endif
diff --git a/board/phytec/pcm058/MAINTAINERS b/board/phytec/pcm058/MAINTAINERS
deleted file mode 100644
index b0ca40277f..0000000000
--- a/board/phytec/pcm058/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@ 
-PHYTEC PHYBOARD MIRA
-M:	Stefano Babic <sbabic at denx.de>
-S:	Maintained
-F:	board/phytec/pcm058/
-F:	include/configs/pcm058.h
-F:	configs/pcm058_defconfig
diff --git a/board/phytec/pcm058/Makefile b/board/phytec/pcm058/Makefile
deleted file mode 100644
index 75b503d95d..0000000000
--- a/board/phytec/pcm058/Makefile
+++ /dev/null
@@ -1,7 +0,0 @@ 
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2007, Guennadi Liakhovetski <lg at denx.de>
-#
-# (C) Copyright 2011 Freescale Semiconductor, Inc.
-
-obj-y  := pcm058.o
diff --git a/board/phytec/pcm058/README b/board/phytec/pcm058/README
deleted file mode 100644
index 3327135645..0000000000
--- a/board/phytec/pcm058/README
+++ /dev/null
@@ -1,35 +0,0 @@ 
-Board information
------------------
-
-The SBC produced by Phytec has a SOM based on a i.MX6Q.
-The SOM is sold in two versions, with eMMC or with NAND. Support
-here is for the SOM with NAND.
-The evaluation board "phyBoard-Mira" is thought to be used
-together with the SOM.
-
-More information on the board can be found on manufacturer's
-website:
-
-http://www.phytec.de/produkt/single-board-computer/phyboard-mira/
-http://www.phytec.de/fileadmin/user_upload/images/content/1.Products/SOMs/phyCORE-i.MX6/L-808e_1.pdf
-
-Building U-Boot
--------------------------------
-
-$ make pcm058_defconfig
-$ make
-
-This generates the artifacts SPL and u-boot.img.
-The SOM can boot from NAND or from SD-Card, having the SPI-NOR
-as second option.
-The dip switch "DIP-1" on the board let choose between
-NAND and SD.
-
-DIP-1 set to off:	Boot first from NAND, then try SPI
-DIP-1 set to on:	Boot first from SD, then try SPI
-
-The bootloader was tested with DIP-1 set to on. If a SD-card
-is present, then the RBL tries to load SPL from the SD Card, if not,
-RBL loads from SPI-NOR. The SPL tries then to load from the same
-device where SPL was loaded (SD or SPI). Booting from NAND is
-not supported.
diff --git a/board/phytec/pcm058/pcm058.c b/board/phytec/pcm058/pcm058.c
deleted file mode 100644
index 096425c5df..0000000000
--- a/board/phytec/pcm058/pcm058.c
+++ /dev/null
@@ -1,571 +0,0 @@ 
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2016 Stefano Babic <sbabic at denx.de>
- */
-
-/*
- * Please note: there are two version of the board
- * one with NAND and the other with eMMC.
- * Both NAND and eMMC cannot be set because they share the
- * same pins (SD4)
- */
-#include <common.h>
-#include <init.h>
-#include <net.h>
-#include <asm/io.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/mx6-ddr.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <asm/mach-imx/spi.h>
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <asm/gpio.h>
-#include <mmc.h>
-#include <i2c.h>
-#include <fsl_esdhc_imx.h>
-#include <nand.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/sections.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
-	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
-	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
-	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
-	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
-
-#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
-	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
-		      PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define I2C_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
-	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
-	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
-#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
-
-#define ASRC_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP  |	\
-		      PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define NAND_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
-	       PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define ENET_PHY_RESET_GPIO IMX_GPIO_NR(1, 14)
-#define USDHC1_CD_GPIO	IMX_GPIO_NR(6, 31)
-#define USER_LED	IMX_GPIO_NR(1, 4)
-#define IMX6Q_DRIVE_STRENGTH	0x30
-
-int dram_init(void)
-{
-	gd->ram_size = imx_ddr_size();
-	return 0;
-}
-
-void board_turn_off_led(void)
-{
-	gpio_direction_output(USER_LED, 0);
-}
-
-static iomux_v3_cfg_t const uart1_pads[] = {
-	MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-	MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const enet_pads[] = {
-	MX6_PAD_ENET_MDIO__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET_MDC__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TXC__RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TD0__RGMII_TD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TD1__RGMII_TD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TD2__RGMII_TD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TD3__RGMII_TD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RXC__RGMII_RXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RD0__RGMII_RD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RD1__RGMII_RD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RD2__RGMII_RD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RD3__RGMII_RD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_SD2_DAT1__GPIO1_IO14	| MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const ecspi1_pads[] = {
-	MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
-	MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
-	MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
-	MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-#ifdef CONFIG_CMD_NAND
-/* NAND */
-static iomux_v3_cfg_t const nfc_pads[] = {
-	MX6_PAD_NANDF_CLE__NAND_CLE     | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_ALE__NAND_ALE     | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_WP_B__NAND_WP_B   | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_CS0__NAND_CE0_B   | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_CS1__NAND_CE1_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_CS2__NAND_CE2_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_CS3__NAND_CE3_B	| MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_SD4_CMD__NAND_RE_B      | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_SD4_CLK__NAND_WE_B      | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_D0__NAND_DATA00   | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_D1__NAND_DATA01   | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_D2__NAND_DATA02   | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_D3__NAND_DATA03   | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_D4__NAND_DATA04   | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_D5__NAND_DATA05   | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_D6__NAND_DATA06   | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_NANDF_D7__NAND_DATA07   | MUX_PAD_CTRL(NAND_PAD_CTRL),
-	MX6_PAD_SD4_DAT0__NAND_DQS	| MUX_PAD_CTRL(NAND_PAD_CTRL),
-};
-#endif
-
-static struct i2c_pads_info i2c_pad_info2 = {
-	.scl = {
-		.i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | I2C_PAD,
-		.gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | I2C_PAD,
-		.gp = IMX_GPIO_NR(1, 5)
-	},
-	.sda = {
-		.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
-		.gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
-		.gp = IMX_GPIO_NR(1, 6)
-	}
-};
-
-static struct fsl_esdhc_cfg usdhc_cfg[] = {
-	{.esdhc_base = USDHC1_BASE_ADDR,
-	.max_bus_width = 4},
-#ifndef CONFIG_CMD_NAND
-	{USDHC4_BASE_ADDR},
-#endif
-};
-
-static iomux_v3_cfg_t const usdhc1_pads[] = {
-	MX6_PAD_SD1_CLK__SD1_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD1_CMD__SD1_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD1_DAT0__SD1_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD1_DAT1__SD1_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD1_DAT2__SD1_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD1_DAT3__SD1_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_EIM_BCLK__GPIO6_IO31	| MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
-
-#if !defined(CONFIG_CMD_NAND) && !defined(CONFIG_SPL_BUILD)
-static iomux_v3_cfg_t const usdhc4_pads[] = {
-	MX6_PAD_SD4_CLK__SD4_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_CMD__SD4_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT0__SD4_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT1__SD4_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT2__SD4_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT3__SD4_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT4__SD4_DATA4	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT5__SD4_DATA5	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT6__SD4_DATA6	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT7__SD4_DATA7	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-};
-#endif
-
-int board_mmc_get_env_dev(int devno)
-{
-	return devno - 1;
-}
-
-int board_mmc_getcd(struct mmc *mmc)
-{
-	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-	int ret = 0;
-
-	switch (cfg->esdhc_base) {
-	case USDHC1_BASE_ADDR:
-		ret = !gpio_get_value(USDHC1_CD_GPIO);
-		break;
-	case USDHC4_BASE_ADDR:
-		ret = 1; /* eMMC/uSDHC4 is always present */
-		break;
-	}
-
-	return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
-#ifndef CONFIG_SPL_BUILD
-	int ret;
-	int i;
-
-	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
-		switch (i) {
-		case 0:
-			imx_iomux_v3_setup_multiple_pads(
-				usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
-			gpio_direction_input(USDHC1_CD_GPIO);
-			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
-			break;
-#ifndef CONFIG_CMD_NAND
-		case 1:
-			imx_iomux_v3_setup_multiple_pads(
-				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
-			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
-			break;
-#endif
-		default:
-			printf("Warning: you configured more USDHC controllers"
-			       "(%d) then supported by the board (%d)\n",
-			       i + 1, CONFIG_SYS_FSL_USDHC_NUM);
-			return -EINVAL;
-		}
-
-		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
-		if (ret)
-			return ret;
-	}
-
-	return 0;
-#else
-	struct src *psrc = (struct src *)SRC_BASE_ADDR;
-	unsigned reg = readl(&psrc->sbmr1) >> 11;
-	/*
-	 * Upon reading BOOT_CFG register the following map is done:
-	 * Bit 11 and 12 of BOOT_CFG register can determine the current
-	 * mmc port
-	 * 0x1                  SD1
-	 * 0x2                  SD2
-	 * 0x3                  SD4
-	 */
-
-	switch (reg & 0x3) {
-	case 0x0:
-		imx_iomux_v3_setup_multiple_pads(
-			usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
-		gpio_direction_input(USDHC1_CD_GPIO);
-		usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR;
-		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
-		usdhc_cfg[0].max_bus_width = 4;
-		gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
-		break;
-	}
-	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-#endif
-}
-
-static void setup_iomux_uart(void)
-{
-	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
-}
-
-static void setup_iomux_enet(void)
-{
-	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
-
-	gpio_direction_output(ENET_PHY_RESET_GPIO, 0);
-	mdelay(10);
-	gpio_set_value(ENET_PHY_RESET_GPIO, 1);
-	mdelay(30);
-}
-
-static void setup_spi(void)
-{
-	gpio_request(IMX_GPIO_NR(3, 19), "spi_cs0");
-	gpio_direction_output(IMX_GPIO_NR(3, 19), 1);
-
-	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
-
-	enable_spi_clk(true, 0);
-}
-
-#ifdef CONFIG_CMD_NAND
-static void setup_gpmi_nand(void)
-{
-	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-
-	/* config gpmi nand iomux */
-	imx_iomux_v3_setup_multiple_pads(nfc_pads, ARRAY_SIZE(nfc_pads));
-
-	/* gate ENFC_CLK_ROOT clock first,before clk source switch */
-	clrbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
-
-	/* config gpmi and bch clock to 100 MHz */
-	clrsetbits_le32(&mxc_ccm->cs2cdr,
-			MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
-			MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
-			MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
-			MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
-			MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
-			MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
-
-	/* enable ENFC_CLK_ROOT clock */
-	setbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
-
-	/* enable gpmi and bch clock gating */
-	setbits_le32(&mxc_ccm->CCGR4,
-		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
-		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
-		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
-		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
-		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
-
-	/* enable apbh clock gating */
-	setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
-}
-#endif
-
-int board_spi_cs_gpio(unsigned bus, unsigned cs)
-{
-	if (bus != 0 || (cs != 0))
-		return -EINVAL;
-
-	return IMX_GPIO_NR(3, 19);
-}
-
-int board_eth_init(bd_t *bis)
-{
-	setup_iomux_enet();
-
-	return cpu_eth_init(bis);
-}
-
-int board_early_init_f(void)
-{
-	setup_iomux_uart();
-
-	return 0;
-}
-
-int board_init(void)
-{
-	/* address of boot parameters */
-	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
-#ifdef CONFIG_SYS_I2C_MXC
-	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
-#endif
-
-#ifdef CONFIG_MXC_SPI
-	setup_spi();
-#endif
-
-#ifdef CONFIG_CMD_NAND
-	setup_gpmi_nand();
-#endif
-	return 0;
-}
-
-
-#ifdef CONFIG_CMD_BMODE
-/*
- * BOOT_CFG1, BOOT_CFG2, BOOT_CFG3, BOOT_CFG4
- * see Table 8-11 and Table 5-9
- *  BOOT_CFG1[7] = 1 (boot from NAND)
- *  BOOT_CFG1[5] = 0 - raw NAND
- *  BOOT_CFG1[4] = 0 - default pad settings
- *  BOOT_CFG1[3:2] = 00 - devices = 1
- *  BOOT_CFG1[1:0] = 00 - Row Address Cycles = 3
- *  BOOT_CFG2[4:3] = 00 - Boot Search Count = 2
- *  BOOT_CFG2[2:1] = 01 - Pages In Block = 64
- *  BOOT_CFG2[0] = 0 - Reset time 12ms
- */
-static const struct boot_mode board_boot_modes[] = {
-	/* NAND: 64pages per block, 3 row addr cycles, 2 copies of FCB/DBBT */
-	{"nand", MAKE_CFGVAL(0x80, 0x02, 0x00, 0x00)},
-	{"mmc0",  MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)},
-	{NULL, 0},
-};
-#endif
-
-int board_late_init(void)
-{
-#ifdef CONFIG_CMD_BMODE
-	add_board_boot_modes(board_boot_modes);
-#endif
-
-	return 0;
-}
-
-#ifdef CONFIG_SPL_BUILD
-#include <spl.h>
-#include <linux/libfdt.h>
-
-static const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
-	.dram_sdclk_0 = 0x00000030,
-	.dram_sdclk_1 = 0x00000030,
-	.dram_cas = 0x00000030,
-	.dram_ras = 0x00000030,
-	.dram_reset = 0x00000030,
-	.dram_sdcke0 = 0x00000030,
-	.dram_sdcke1 = 0x00000030,
-	.dram_sdba2 = 0x00000000,
-	.dram_sdodt0 = 0x00000030,
-	.dram_sdodt1 = 0x00000030,
-	.dram_sdqs0 = 0x00000030,
-	.dram_sdqs1 = 0x00000030,
-	.dram_sdqs2 = 0x00000030,
-	.dram_sdqs3 = 0x00000030,
-	.dram_sdqs4 = 0x00000030,
-	.dram_sdqs5 = 0x00000030,
-	.dram_sdqs6 = 0x00000030,
-	.dram_sdqs7 = 0x00000030,
-	.dram_dqm0 = 0x00000030,
-	.dram_dqm1 = 0x00000030,
-	.dram_dqm2 = 0x00000030,
-	.dram_dqm3 = 0x00000030,
-	.dram_dqm4 = 0x00000030,
-	.dram_dqm5 = 0x00000030,
-	.dram_dqm6 = 0x00000030,
-	.dram_dqm7 = 0x00000030,
-};
-
-static const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
-	.grp_ddr_type =  0x000C0000,
-	.grp_ddrmode_ctl =  0x00020000,
-	.grp_ddrpke =  0x00000000,
-	.grp_addds = IMX6Q_DRIVE_STRENGTH,
-	.grp_ctlds = IMX6Q_DRIVE_STRENGTH,
-	.grp_ddrmode =  0x00020000,
-	.grp_b0ds = IMX6Q_DRIVE_STRENGTH,
-	.grp_b1ds = IMX6Q_DRIVE_STRENGTH,
-	.grp_b2ds = IMX6Q_DRIVE_STRENGTH,
-	.grp_b3ds = IMX6Q_DRIVE_STRENGTH,
-	.grp_b4ds = IMX6Q_DRIVE_STRENGTH,
-	.grp_b5ds = IMX6Q_DRIVE_STRENGTH,
-	.grp_b6ds = IMX6Q_DRIVE_STRENGTH,
-	.grp_b7ds = IMX6Q_DRIVE_STRENGTH,
-};
-
-static const struct mx6_mmdc_calibration mx6_mmcd_calib = {
-	.p0_mpwldectrl0 =  0x00140014,
-	.p0_mpwldectrl1 =  0x000A0015,
-	.p1_mpwldectrl0 =  0x000A001E,
-	.p1_mpwldectrl1 =  0x000A0015,
-	.p0_mpdgctrl0 =  0x43080314,
-	.p0_mpdgctrl1 =  0x02680300,
-	.p1_mpdgctrl0 =  0x430C0318,
-	.p1_mpdgctrl1 =  0x03000254,
-	.p0_mprddlctl =  0x3A323234,
-	.p1_mprddlctl =  0x3E3C3242,
-	.p0_mpwrdlctl =  0x2A2E3632,
-	.p1_mpwrdlctl =  0x3C323E34,
-};
-
-static struct mx6_ddr3_cfg mem_ddr = {
-	.mem_speed = 1600,
-	.density = 2,
-	.width = 16,
-	.banks = 8,
-	.rowaddr = 14,
-	.coladdr = 10,
-	.pagesz = 2,
-	.trcd = 1375,
-	.trcmin = 4875,
-	.trasmin = 3500,
-	.SRT       = 1,
-};
-
-static void ccgr_init(void)
-{
-	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-
-	writel(0x00C03F3F, &ccm->CCGR0);
-	writel(0x0030FC03, &ccm->CCGR1);
-	writel(0x0FFFC000, &ccm->CCGR2);
-	writel(0x3FF00000, &ccm->CCGR3);
-	writel(0x00FFF300, &ccm->CCGR4);
-	writel(0x0F0000C3, &ccm->CCGR5);
-	writel(0x000003FF, &ccm->CCGR6);
-}
-
-static void spl_dram_init(void)
-{
-	struct mx6_ddr_sysinfo sysinfo = {
-		/* width of data bus:0=16,1=32,2=64 */
-		.dsize = 2,
-		/* config for full 4GB range so that get_mem_size() works */
-		.cs_density = 32, /* 32Gb per CS */
-		/* single chip select */
-		.ncs = 1,
-		.cs1_mirror = 0,
-		.rtt_wr = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Wr = RZQ/4 */
-		.rtt_nom = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Nom = RZQ/4 */
-		.walat = 1,	/* Write additional latency */
-		.ralat = 5,	/* Read additional latency */
-		.mif3_mode = 3,	/* Command prediction working mode */
-		.bi_on = 1,	/* Bank interleaving enabled */
-		.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
-		.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
-		.ddr_type = DDR_TYPE_DDR3,
-		.refsel = 1,	/* Refresh cycles at 32KHz */
-		.refr = 7,	/* 8 refresh commands per refresh cycle */
-	};
-
-	mx6dq_dram_iocfg(64, &mx6_ddr_ioregs, &mx6_grp_ioregs);
-	mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
-}
-
-void board_boot_order(u32 *spl_boot_list)
-{
-	spl_boot_list[0] = spl_boot_device();
-	printf("Boot device %x\n", spl_boot_list[0]);
-	switch (spl_boot_list[0]) {
-	case BOOT_DEVICE_SPI:
-		spl_boot_list[1] = BOOT_DEVICE_UART;
-		break;
-	case BOOT_DEVICE_MMC1:
-		spl_boot_list[1] = BOOT_DEVICE_SPI;
-		spl_boot_list[2] = BOOT_DEVICE_UART;
-		break;
-	default:
-		printf("Boot device %x\n", spl_boot_list[0]);
-	}
-}
-
-void board_init_f(ulong dummy)
-{
-#ifdef CONFIG_CMD_NAND
-	/* Enable NAND */
-	setup_gpmi_nand();
-#endif
-
-	/* setup clock gating */
-	ccgr_init();
-
-	/* setup AIPS and disable watchdog */
-	arch_cpu_init();
-
-	/* setup AXI */
-	gpr_init();
-
-	board_early_init_f();
-
-	/* setup GP timer */
-	timer_init();
-
-	setup_spi();
-
-	/* UART clocks enabled and gd valid - init serial console */
-	preloader_console_init();
-
-	/* DDR initialization */
-	spl_dram_init();
-
-	/* Clear the BSS. */
-	memset(__bss_start, 0, __bss_end - __bss_start);
-
-	/* load/boot image from boot device */
-	board_init_r(NULL, 0);
-}
-#endif
diff --git a/configs/pcm058_defconfig b/configs/pcm058_defconfig
deleted file mode 100644
index 0dfbc172c2..0000000000
--- a/configs/pcm058_defconfig
+++ /dev/null
@@ -1,70 +0,0 @@ 
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x4000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
-CONFIG_TARGET_PCM058=y
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_SPL=y
-CONFIG_ENV_OFFSET_REDUND=0x110000
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI_SUPPORT=y
-CONFIG_CMD_HDMIDETECT=y
-CONFIG_SPL_TEXT_BASE=0x00908000
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,MX6Q"
-CONFIG_BOOTDELAY=3
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_SPL_DMA=y
-CONFIG_SPL_FS_EXT4=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_SPI_LOAD=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
-CONFIG_SPL_YMODEM_SUPPORT=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND_TRIMFFS=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=nand:16m(uboot),1m(env),-(rootfs)"
-CONFIG_CMD_UBI=y
-# CONFIG_SPL_PARTITION_UUIDS is not set
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_DM=y
-CONFIG_FSL_USDHC=y
-CONFIG_MTD=y
-CONFIG_DM_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_SYS_NAND_USE_FLASH_BBT=y
-CONFIG_NAND_MXS=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=20000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_MICREL=y
-CONFIG_PHY_MICREL_KSZ90X1=y
-CONFIG_MII=y
-CONFIG_SPI=y
-CONFIG_MXC_SPI=y
-CONFIG_DM_THERMAL=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/pcm058.h b/include/configs/pcm058.h
deleted file mode 100644
index 7c27ebb811..0000000000
--- a/include/configs/pcm058.h
+++ /dev/null
@@ -1,77 +0,0 @@ 
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) Stefano Babic <sbabic at denx.de>
- */
-
-
-#ifndef __PCM058_CONFIG_H
-#define __PCM058_CONFIG_H
-
-#ifdef CONFIG_SPL
-#include "imx6_spl.h"
-#endif
-
-#include "mx6_common.h"
-
-/* Thermal */
-#define CONFIG_IMX_THERMAL
-
-/* Serial */
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE	       UART2_BASE
-#define CONSOLE_DEV		"ttymxc1"
-
-#define PHYS_SDRAM_SIZE		(1u * 1024 * 1024 * 1024)
-
-/* Early setup */
-
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN		(8 * SZ_1M)
-
-/* Ethernet */
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE			ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE		RGMII
-#define CONFIG_ETHPRIME			"FEC"
-#define CONFIG_FEC_MXC_PHYADDR		3
-
-/* SPI Flash */
-
-/* I2C Configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_SPEED		  100000
-
-#ifndef CONFIG_SPL_BUILD
-/* Enable NAND support */
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		0x40000000
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#endif
-
-/* DMA stuff, needed for GPMI/MXS NAND support */
-
-/* Filesystem support */
-
-/* Physical Memory Map */
-#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
-	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
-	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/* MMC Configs */
-#define CONFIG_SYS_FSL_ESDHC_ADDR	0
-#define CONFIG_SYS_FSL_USDHC_NUM	1
-
-/* Environment organization */
-
-#endif