@@ -108,12 +108,6 @@ choice
prompt "MX6 board select"
optional
-config TARGET_ADVANTECH_DMS_BA16
- bool "Advantech dms-ba16"
- select BOARD_LATE_INIT
- select MX6Q
- imply CMD_SATA
-
config TARGET_APALIS_IMX6
bool "Toradex Apalis iMX6 board"
select BOARD_LATE_INIT
@@ -641,7 +635,6 @@ config SYS_SOC
default "mx6"
source "board/ge/bx50v3/Kconfig"
-source "board/advantech/dms-ba16/Kconfig"
source "board/aristainetos/Kconfig"
source "board/armadeus/opos6uldev/Kconfig"
source "board/barco/platinum/Kconfig"
deleted file mode 100644
@@ -1,31 +0,0 @@
-if TARGET_ADVANTECH_DMS_BA16
-
-choice
- prompt "DDR Size"
- default SYS_DDR_2G
-
-config SYS_DDR_1G
- bool "1GiB"
-
-config SYS_DDR_2G
- bool "2GiB"
-
-endchoice
-
-config IMX_CONFIG
- default "board/advantech/dms-ba16/dms-ba16_2g.cfg" if SYS_DDR_2G
- default "board/advantech/dms-ba16/dms-ba16_1g.cfg" if SYS_DDR_1G
-
-config SYS_BOARD
- default "dms-ba16"
-
-config SYS_VENDOR
- default "advantech"
-
-config SYS_SOC
- default "mx6"
-
-config SYS_CONFIG_NAME
- default "advantech_dms-ba16"
-
-endif
deleted file mode 100644
@@ -1,8 +0,0 @@
-ADVANTECH_DMS-BA16 BOARD
-M: Akshay Bhat <akshaybhat at timesys.com>
-M: Ken Lin <Ken.Lin at advantech.com.tw>
-S: Maintained
-F: board/advantech/dms-ba16/
-F: include/configs/advantech_dms-ba16.h
-F: configs/dms-ba16_defconfig
-F: configs/dms-ba16-1g_defconfig
deleted file mode 100644
@@ -1,6 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright 2016 Timesys Corporation
-# Copyright 2016 Advantech Corporation
-
-obj-y := dms-ba16.o
deleted file mode 100644
@@ -1,25 +0,0 @@
-/* set the default clock gate to save power */
-DATA 4, CCM_CCGR0, 0x00C03F3F
-DATA 4, CCM_CCGR1, 0x0030FC03
-DATA 4, CCM_CCGR2, 0x0FFFC000
-DATA 4, CCM_CCGR3, 0x3FF00000
-DATA 4, CCM_CCGR4, 0x00FFF300
-DATA 4, CCM_CCGR5, 0x0F0000C3
-DATA 4, CCM_CCGR6, 0x000003FF
-
-/* enable AXI cache for VDOA/VPU/IPU */
-DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF
-/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
-DATA 4, MX6_IOMUXC_GPR6, 0x007F007F
-DATA 4, MX6_IOMUXC_GPR7, 0x007F007F
-
-/*
- * Setup CCM_CCOSR register as follows:
- *
- * cko1_en 1 --> CKO1 enabled
- * cko1_div 111 --> divide by 8
- * cko1_sel 1011 --> ahb_clk_root
- *
- * This sets CKO1 at ahb_clk_root/8 132/8 16.5 MHz
- */
-DATA 4, CCM_CCOSR, 0x000000fb
deleted file mode 100644
@@ -1,39 +0,0 @@
-/* DDR IO */
-DATA 4, MX6_IOM_GRP_DDR_TYPE, 0x000c0000
-DATA 4, MX6_IOM_GRP_DDRPKE, 0x00000000
-DATA 4, MX6_IOM_DRAM_SDCLK_0, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDCLK_1, 0x00000030
-DATA 4, MX6_IOM_DRAM_CAS, 0x00000030
-DATA 4, MX6_IOM_DRAM_RAS, 0x00000030
-DATA 4, MX6_IOM_GRP_ADDDS, 0x00000030
-DATA 4, MX6_IOM_DRAM_RESET, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDBA2, 0x00000000
-DATA 4, MX6_IOM_DRAM_SDODT0, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDODT1, 0x00000030
-DATA 4, MX6_IOM_GRP_CTLDS, 0x00000030
-DATA 4, MX6_IOM_DDRMODE_CTL, 0x00020000
-DATA 4, MX6_IOM_DRAM_SDQS0, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS1, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS2, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS3, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS4, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS5, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS6, 0x00000030
-DATA 4, MX6_IOM_DRAM_SDQS7, 0x00000030
-DATA 4, MX6_IOM_GRP_DDRMODE, 0x00020000
-DATA 4, MX6_IOM_GRP_B0DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B1DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B2DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B3DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B4DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B5DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B6DS, 0x00000030
-DATA 4, MX6_IOM_GRP_B7DS, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM0, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM1, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM2, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM3, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM4, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM5, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM6, 0x00000030
-DATA 4, MX6_IOM_DRAM_DQM7, 0x00000030
deleted file mode 100644
@@ -1,629 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2016 Timesys Corporation
- * Copyright 2016 Advantech Corporation
- * Copyright 2012 Freescale Semiconductor, Inc.
- */
-
-#include <init.h>
-#include <net.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-pins.h>
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/video.h>
-#include <mmc.h>
-#include <fsl_esdhc_imx.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <asm/arch/mxc_hdmi.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/io.h>
-#include <asm/arch/sys_proto.h>
-#include <i2c.h>
-#include <input.h>
-#include <pwm.h>
-DECLARE_GLOBAL_DATA_PTR;
-
-#define NC_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_HYS)
-
-#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
- PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
- PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
-
-#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST)
-
-#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST)
-
-#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
-#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
-
-int dram_init(void)
-{
- gd->ram_size = imx_ddr_size();
-
- return 0;
-}
-
-static iomux_v3_cfg_t const uart3_pads[] = {
- MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const uart4_pads[] = {
- MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const enet_pads[] = {
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
- MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- /* AR8033 PHY Reset */
- MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static void setup_iomux_enet(void)
-{
- imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
-
- /* Reset AR8033 PHY */
- gpio_direction_output(IMX_GPIO_NR(1, 28), 0);
- mdelay(10);
- gpio_set_value(IMX_GPIO_NR(1, 28), 1);
- mdelay(1);
-}
-
-static iomux_v3_cfg_t const usdhc2_pads[] = {
- MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const usdhc3_pads[] = {
- MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const usdhc4_pads[] = {
- MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const ecspi1_pads[] = {
- MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static struct i2c_pads_info i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD,
- .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD,
- .gp = IMX_GPIO_NR(5, 27)
- },
- .sda = {
- .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD,
- .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD,
- .gp = IMX_GPIO_NR(5, 26)
- }
-};
-
-static struct i2c_pads_info i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
- .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 12)
- },
- .sda = {
- .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
- .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
-static struct i2c_pads_info i2c_pad_info3 = {
- .scl = {
- .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD,
- .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD,
- .gp = IMX_GPIO_NR(1, 3)
- },
- .sda = {
- .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
- .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
- .gp = IMX_GPIO_NR(1, 6)
- }
-};
-
-#ifdef CONFIG_MXC_SPI
-int board_spi_cs_gpio(unsigned bus, unsigned cs)
-{
- return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1;
-}
-
-static void setup_spi(void)
-{
- imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
-}
-#endif
-
-static iomux_v3_cfg_t const pcie_pads[] = {
- MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static void setup_pcie(void)
-{
- imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
-}
-
-static void setup_iomux_uart(void)
-{
- imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
- imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
-}
-
-#ifdef CONFIG_FSL_ESDHC_IMX
-struct fsl_esdhc_cfg usdhc_cfg[3] = {
- {USDHC2_BASE_ADDR},
- {USDHC3_BASE_ADDR},
- {USDHC4_BASE_ADDR},
-};
-
-#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4)
-#define USDHC4_CD_GPIO IMX_GPIO_NR(6, 11)
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret = 0;
-
- switch (cfg->esdhc_base) {
- case USDHC2_BASE_ADDR:
- ret = !gpio_get_value(USDHC2_CD_GPIO);
- break;
- case USDHC3_BASE_ADDR:
- ret = 1; /* eMMC is always present */
- break;
- case USDHC4_BASE_ADDR:
- ret = !gpio_get_value(USDHC4_CD_GPIO);
- break;
- }
-
- return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
- int ret;
- int i;
-
- for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
- switch (i) {
- case 0:
- imx_iomux_v3_setup_multiple_pads(
- usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
- gpio_direction_input(USDHC2_CD_GPIO);
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- break;
- case 1:
- imx_iomux_v3_setup_multiple_pads(
- usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- break;
- case 2:
- imx_iomux_v3_setup_multiple_pads(
- usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
- gpio_direction_input(USDHC4_CD_GPIO);
- usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
- break;
- default:
- printf("Warning: you configured more USDHC controllers\n"
- "(%d) then supported by the board (%d)\n",
- i + 1, CONFIG_SYS_FSL_USDHC_NUM);
- return -EINVAL;
- }
-
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
- if (ret)
- return ret;
- }
-
- return 0;
-}
-#endif
-
-static int mx6_rgmii_rework(struct phy_device *phydev)
-{
- /* set device address 0x7 */
- phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
- /* offset 0x8016: CLK_25M Clock Select */
- phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
- /* enable register write, no post increment, address 0x7 */
- phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
- /* set to 125 MHz from local PLL source */
- phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x18);
- /* set debug port address: SerDes Test and System Mode Control */
- phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
- /* enable rgmii tx clock delay */
- /* set the reserved bits to avoid board specific voltage peak issue*/
- phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x3D47);
-
- return 0;
-}
-
-int board_phy_config(struct phy_device *phydev)
-{
- mx6_rgmii_rework(phydev);
-
- if (phydev->drv->config)
- phydev->drv->config(phydev);
-
- return 0;
-}
-
-#if defined(CONFIG_VIDEO_IPUV3)
-static iomux_v3_cfg_t const backlight_pads[] = {
- /* Power for LVDS Display */
- MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
-#define LVDS_POWER_GP IMX_GPIO_NR(3, 22)
- /* Backlight enable for LVDS display */
- MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
-#define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0)
- /* backlight PWM brightness control */
- MX6_PAD_SD1_DAT3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static void do_enable_hdmi(struct display_info_t const *dev)
-{
- imx_enable_hdmi_phy();
-}
-
-int board_cfb_skip(void)
-{
- gpio_direction_output(LVDS_POWER_GP, 1);
-
- return 0;
-}
-
-static int detect_baseboard(struct display_info_t const *dev)
-{
- return 0 == dev->addr;
-}
-
-struct display_info_t const displays[] = {{
- .bus = -1,
- .addr = 0,
- .pixfmt = IPU_PIX_FMT_RGB24,
- .detect = detect_baseboard,
- .enable = NULL,
- .mode = {
- .name = "SHARP-LQ156M1LG21",
- .refresh = 60,
- .xres = 1920,
- .yres = 1080,
- .pixclock = 7851,
- .left_margin = 100,
- .right_margin = 40,
- .upper_margin = 30,
- .lower_margin = 3,
- .hsync_len = 10,
- .vsync_len = 2,
- .sync = FB_SYNC_EXT,
- .vmode = FB_VMODE_NONINTERLACED
-} }, {
- .bus = -1,
- .addr = 3,
- .pixfmt = IPU_PIX_FMT_RGB24,
- .detect = detect_hdmi,
- .enable = do_enable_hdmi,
- .mode = {
- .name = "HDMI",
- .refresh = 60,
- .xres = 1024,
- .yres = 768,
- .pixclock = 15385,
- .left_margin = 220,
- .right_margin = 40,
- .upper_margin = 21,
- .lower_margin = 7,
- .hsync_len = 60,
- .vsync_len = 10,
- .sync = FB_SYNC_EXT,
- .vmode = FB_VMODE_NONINTERLACED
-} } };
-size_t display_count = ARRAY_SIZE(displays);
-
-static void setup_display(void)
-{
- struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
- struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
-
- clrbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
-
- imx_setup_hdmi();
-
- /* Set LDB_DI0 as clock source for IPU_DI0 */
- clrsetbits_le32(&mxc_ccm->chsccdr,
- MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK,
- (CHSCCDR_CLK_SEL_LDB_DI0 <<
- MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET));
-
- /* Turn on IPU LDB DI0 clocks */
- setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
-
- enable_ipu_clock();
-
- writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
- IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH |
- IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
- IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG |
- IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT |
- IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
- IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
- IOMUXC_GPR2_SPLIT_MODE_EN_MASK |
- IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0 |
- IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0,
- &iomux->gpr[2]);
-
- clrsetbits_le32(&iomux->gpr[3],
- IOMUXC_GPR3_LVDS0_MUX_CTL_MASK |
- IOMUXC_GPR3_LVDS1_MUX_CTL_MASK |
- IOMUXC_GPR3_HDMI_MUX_CTL_MASK,
- (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <<
- IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET));
-
- /* backlights off until needed */
- imx_iomux_v3_setup_multiple_pads(backlight_pads,
- ARRAY_SIZE(backlight_pads));
-
- gpio_direction_input(LVDS_POWER_GP);
- gpio_direction_input(LVDS_BACKLIGHT_GP);
-}
-#endif /* CONFIG_VIDEO_IPUV3 */
-
-/*
- * Do not overwrite the console
- * Use always serial for U-Boot console
- */
-int overwrite_console(void)
-{
- return 1;
-}
-
-int board_eth_init(bd_t *bis)
-{
- setup_iomux_enet();
- setup_pcie();
-
- return cpu_eth_init(bis);
-}
-
-static iomux_v3_cfg_t const misc_pads[] = {
- MX6_PAD_KEY_ROW2__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NC_PAD_CTRL),
- MX6_PAD_EIM_CS0__GPIO2_IO23 | MUX_PAD_CTRL(NC_PAD_CTRL),
- MX6_PAD_EIM_CS1__GPIO2_IO24 | MUX_PAD_CTRL(NC_PAD_CTRL),
- MX6_PAD_EIM_OE__GPIO2_IO25 | MUX_PAD_CTRL(NC_PAD_CTRL),
- MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NC_PAD_CTRL),
- MX6_PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NC_PAD_CTRL),
-};
-#define SUS_S3_OUT IMX_GPIO_NR(4, 11)
-#define WIFI_EN IMX_GPIO_NR(6, 14)
-
-int setup_ba16_sata(void)
-{
- struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
- int ret;
-
- ret = enable_sata_clock();
- if (ret)
- return ret;
-
- clrsetbits_le32(&iomuxc_regs->gpr[13],
- IOMUXC_GPR13_SATA_MASK,
- IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB
- |IOMUXC_GPR13_SATA_PHY_7_SATA2M
- |IOMUXC_GPR13_SATA_SPEED_3G
- |(1<<IOMUXC_GPR13_SATA_PHY_6_SHIFT)
- |IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED
- |IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_12_16
- |IOMUXC_GPR13_SATA_PHY_3_TXBOOST_3P33_DB
- |IOMUXC_GPR13_SATA_PHY_2_TX_1P133V
- |IOMUXC_GPR13_SATA_PHY_1_SLOW);
-
- return 0;
-}
-
-int board_early_init_f(void)
-{
- imx_iomux_v3_setup_multiple_pads(misc_pads,
- ARRAY_SIZE(misc_pads));
-
- setup_iomux_uart();
-
-#if defined(CONFIG_VIDEO_IPUV3)
- /* Set LDB clock to PLL2 PFD0 */
- select_ldb_di_clock_source(MXC_PLL2_PFD0_CLK);
-#endif
- return 0;
-}
-
-int board_init(void)
-{
- gpio_direction_output(SUS_S3_OUT, 1);
- gpio_direction_output(WIFI_EN, 1);
-#if defined(CONFIG_VIDEO_IPUV3)
- setup_display();
-#endif
- /* address of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
-#ifdef CONFIG_MXC_SPI
- setup_spi();
-#endif
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
- setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
-
- return 0;
-}
-
-#ifdef CONFIG_CMD_BMODE
-static const struct boot_mode board_boot_modes[] = {
- /* 4 bit bus width */
- {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
- {"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
- {NULL, 0},
-};
-#endif
-
-void pmic_init(void)
-{
-
-#define DA9063_ADDR 0x58
-#define BCORE2_CONF 0x9D
-#define BCORE1_CONF 0x9E
-#define BPRO_CONF 0x9F
-#define BIO_CONF 0xA0
-#define BMEM_CONF 0xA1
-#define BPERI_CONF 0xA2
-#define MODE_BIT_H 7
-#define MODE_BIT_L 6
-
- uchar val;
- i2c_set_bus_num(2);
-
- i2c_read(DA9063_ADDR, BCORE2_CONF, 1, &val, 1);
- val |= (1 << MODE_BIT_H);
- val &= ~(1 << MODE_BIT_L);
- i2c_write(DA9063_ADDR, BCORE2_CONF , 1, &val, 1);
-
- i2c_read(DA9063_ADDR, BCORE1_CONF, 1, &val, 1);
- val |= (1 << MODE_BIT_H);
- val &= ~(1 << MODE_BIT_L);
- i2c_write(DA9063_ADDR, BCORE1_CONF , 1, &val, 1);
-
- i2c_read(DA9063_ADDR, BPRO_CONF, 1, &val, 1);
- val |= (1 << MODE_BIT_H);
- val &= ~(1 << MODE_BIT_L);
- i2c_write(DA9063_ADDR, BPRO_CONF , 1, &val, 1);
-
- i2c_read(DA9063_ADDR, BIO_CONF, 1, &val, 1);
- val |= (1 << MODE_BIT_H);
- val &= ~(1 << MODE_BIT_L);
- i2c_write(DA9063_ADDR, BIO_CONF , 1, &val, 1);
-
- i2c_read(DA9063_ADDR, BMEM_CONF, 1, &val, 1);
- val |= (1 << MODE_BIT_H);
- val &= ~(1 << MODE_BIT_L);
- i2c_write(DA9063_ADDR, BMEM_CONF , 1, &val, 1);
-
- i2c_read(DA9063_ADDR, BPERI_CONF, 1, &val, 1);
- val |= (1 << MODE_BIT_H);
- val &= ~(1 << MODE_BIT_L);
- i2c_write(DA9063_ADDR, BPERI_CONF , 1, &val, 1);
-
-}
-
-int board_late_init(void)
-{
-#ifdef CONFIG_CMD_BMODE
- add_board_boot_modes(board_boot_modes);
-#endif
-
-#if defined(CONFIG_VIDEO_IPUV3)
- /*
- * We need at least 200ms between power on and backlight on
- * as per specifications from CHI MEI
- */
- mdelay(250);
-
- /* enable backlight PWM 1 */
- pwm_init(0, 0, 0);
-
- /* duty cycle 5000000ns, period: 5000000ns */
- pwm_config(0, 5000000, 5000000);
-
- /* Backlight Power */
- gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
-
- pwm_enable(0);
-#endif
-
-#ifdef CONFIG_SATA
- setup_ba16_sata();
-#endif
-
- /* board specific pmic init */
- pmic_init();
-
- return 0;
-}
-
-int checkboard(void)
-{
- printf("BOARD: %s\n", CONFIG_BOARD_NAME);
- return 0;
-}
deleted file mode 100644
@@ -1,24 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- *
- * Copyright 2015 Timesys Corporation.
- * Copyright 2015 General Electric Company
- *
- * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure
- * and create imximage boot image
- *
- * The syntax is taken as close as possible with the kwbimage
- */
-
-IMAGE_VERSION 2
-BOOT_FROM sd
-
-#define __ASSEMBLY__
-#include <config.h>
-#include "asm/arch/mx6-ddr.h"
-#include "asm/arch/iomux.h"
-#include "asm/arch/crm_regs.h"
-
-#include "ddr-setup.cfg"
-#include "micron-1g.cfg"
-#include "clocks.cfg"
deleted file mode 100644
@@ -1,24 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- *
- * Copyright 2015 Timesys Corporation.
- * Copyright 2015 General Electric Company
- *
- * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure
- * and create imximage boot image
- *
- * The syntax is taken as close as possible with the kwbimage
- */
-
-IMAGE_VERSION 2
-BOOT_FROM sd
-
-#define __ASSEMBLY__
-#include <config.h>
-#include "asm/arch/mx6-ddr.h"
-#include "asm/arch/iomux.h"
-#include "asm/arch/crm_regs.h"
-
-#include "ddr-setup.cfg"
-#include "samsung-2g.cfg"
-#include "clocks.cfg"
deleted file mode 100644
@@ -1,63 +0,0 @@
-/* Calibrations */
-/* ZQ */
-DATA 4, MX6_MMDC_P0_MPZQHWCTRL, 0xa1390003
-/* write leveling */
-DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x001F001F
-DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x001F001F
-DATA 4, MX6_MMDC_P1_MPWLDECTRL0, 0x001F001F
-DATA 4, MX6_MMDC_P1_MPWLDECTRL1, 0x001F001F
-/* Read DQS Gating calibration */
-DATA 4, MX6_MMDC_P0_MPDGCTRL0, 0x43480350
-DATA 4, MX6_MMDC_P0_MPDGCTRL1, 0x033C0340
-DATA 4, MX6_MMDC_P1_MPDGCTRL0, 0x43480350
-DATA 4, MX6_MMDC_P1_MPDGCTRL1, 0x03340314
-/* Read calibration */
-DATA 4, MX6_MMDC_P0_MPRDDLCTL, 0x382E2C32
-DATA 4, MX6_MMDC_P1_MPRDDLCTL, 0x38363044
-/* Write calibration */
-DATA 4 MX6_MMDC_P0_MPWRDLCTL, 0x3A38403A
-DATA 4 MX6_MMDC_P1_MPWRDLCTL, 0x4432483E
-/* read data bit delay */
-DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333
-
-/* Complete calibration by forced measurment */
-DATA 4, MX6_MMDC_P0_MPMUR0, 0x00000800
-DATA 4, MX6_MMDC_P1_MPMUR0, 0x00000800
-
-/* MMDC init */
-DATA 4, MX6_MMDC_P0_MDPDC, 0x00020036
-DATA 4, MX6_MMDC_P0_MDOTC, 0x09444040
-DATA 4, MX6_MMDC_P0_MDCFG0, 0x555A79A5
-DATA 4, MX6_MMDC_P0_MDCFG1, 0xDB538E64
-DATA 4, MX6_MMDC_P0_MDCFG2, 0x01ff00db
-DATA 4, MX6_MMDC_P0_MDMISC, 0x00001740
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00008000
-DATA 4, MX6_MMDC_P0_MDRWD, 0x000026d2
-DATA 4, MX6_MMDC_P0_MDOR, 0x005a1023
-DATA 4, MX6_MMDC_P0_MDASP, 0x00000027
-DATA 4, MX6_MMDC_P0_MDCTL, 0x831a0000
-
-/* Initialize memory */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x04088032
-DATA 4, MX6_MMDC_P0_MDSCR, 0x0408803a
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00008033
-DATA 4, MX6_MMDC_P0_MDSCR, 0x0000803b
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00048031
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00048039
-DATA 4, MX6_MMDC_P0_MDSCR, 0x09408030
-DATA 4, MX6_MMDC_P0_MDSCR, 0x09408038
-DATA 4, MX6_MMDC_P0_MDSCR, 0x04008040
-DATA 4, MX6_MMDC_P0_MDSCR, 0x04008048
-DATA 4, MX6_MMDC_P0_MDREF, 0x00005800
-DATA 4, MX6_MMDC_P0_MPODTCTRL, 0x00033337
-DATA 4, MX6_MMDC_P1_MPODTCTRL, 0x00033337
-DATA 4, MX6_MMDC_P0_MDPDC, 0x00025576
-DATA 4, MX6_MMDC_P0_MAPSR, 0x00011006
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00000000
deleted file mode 100644
@@ -1,63 +0,0 @@
-/* Calibrations */
-/* ZQ */
-DATA 4, MX6_MMDC_P0_MPZQHWCTRL, 0xa1390003
-/* write leveling */
-DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x001F001F
-DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x001F001F
-DATA 4, MX6_MMDC_P1_MPWLDECTRL0, 0x001F001F
-DATA 4, MX6_MMDC_P1_MPWLDECTRL1, 0x001F001F
-/* Read DQS Gating calibration */
-DATA 4, MX6_MMDC_P0_MPDGCTRL0, 0x45380544
-DATA 4, MX6_MMDC_P0_MPDGCTRL1, 0x05280530
-DATA 4, MX6_MMDC_P1_MPDGCTRL0, 0x4530053C
-DATA 4, MX6_MMDC_P1_MPDGCTRL1, 0x0530050C
-/* Read calibration */
-DATA 4, MX6_MMDC_P0_MPRDDLCTL, 0x36303032
-DATA 4, MX6_MMDC_P1_MPRDDLCTL, 0x38363042
-/* Write calibration */
-DATA 4, MX6_MMDC_P0_MPWRDLCTL, 0x3A3A423E
-DATA 4, MX6_MMDC_P1_MPWRDLCTL, 0x4A38483E
-/* read data bit delay */
-DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
-DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333
-DATA 4, MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333
-
-/* Complete calibration by forced measurment */
-DATA 4, MX6_MMDC_P0_MPMUR0, 0x00000800
-DATA 4, MX6_MMDC_P1_MPMUR0, 0x00000800
-
-/* MMDC init */
-DATA 4, MX6_MMDC_P0_MDPDC, 0x00020036
-DATA 4, MX6_MMDC_P0_MDOTC, 0x09444040
-DATA 4, MX6_MMDC_P0_MDCFG0, 0x8A8F79A4
-DATA 4, MX6_MMDC_P0_MDCFG1, 0xDB538E64
-DATA 4, MX6_MMDC_P0_MDCFG2, 0x01ff00db
-DATA 4, MX6_MMDC_P0_MDMISC, 0x00001740
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00008000
-DATA 4, MX6_MMDC_P0_MDRWD, 0x000026d2
-DATA 4, MX6_MMDC_P0_MDOR, 0x008F1023
-DATA 4, MX6_MMDC_P0_MDASP, 0x00000047
-DATA 4, MX6_MMDC_P0_MDCTL, 0x841a0000
-
-/* Initialize memory */
-DATA 4, MX6_MMDC_P0_MDSCR, 0x04088032
-DATA 4, MX6_MMDC_P0_MDSCR, 0x0408803a
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00008033
-DATA 4, MX6_MMDC_P0_MDSCR, 0x0000803b
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00408031
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00408039
-DATA 4, MX6_MMDC_P0_MDSCR, 0x09408030
-DATA 4, MX6_MMDC_P0_MDSCR, 0x09408038
-DATA 4, MX6_MMDC_P0_MDSCR, 0x04008040
-DATA 4, MX6_MMDC_P0_MDSCR, 0x04008048
-DATA 4, MX6_MMDC_P0_MDREF, 0x00005800
-DATA 4, MX6_MMDC_P0_MPODTCTRL, 0x00011117
-DATA 4, MX6_MMDC_P1_MPODTCTRL, 0x00011117
-DATA 4, MX6_MMDC_P0_MDPDC, 0x00025576
-DATA 4, MX6_MMDC_P0_MAPSR, 0x00011006
-DATA 4, MX6_MMDC_P0_MDSCR, 0x00000000
deleted file mode 100644
@@ -1,64 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0xC0000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_TARGET_ADVANTECH_DMS_BA16=y
-CONFIG_SYS_DDR_1G=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_BOOTDELAY=1
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_DEFAULT_FDT_FILE="imx6q-dms-ba16.dtb"
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_USB_MASS_STORAGE=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_DWC_AHSATA=y
-CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_FSL_USDHC=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=20000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_WINBOND=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_MII=y
-CONFIG_PWM_IMX=y
-CONFIG_SPI=y
-CONFIG_MXC_SPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_KEYBOARD=y
-CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Advantech"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0525
-CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
-CONFIG_CI_UDC=y
-CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_VIDEO_IPUV3=y
-CONFIG_VIDEO=y
-# CONFIG_VIDEO_SW_CURSOR is not set
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,63 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0xC0000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_TARGET_ADVANTECH_DMS_BA16=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_BOOTDELAY=1
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_DEFAULT_FDT_FILE="imx6q-dms-ba16.dtb"
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_USB_MASS_STORAGE=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_DWC_AHSATA=y
-CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_FSL_USDHC=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=20000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_WINBOND=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_MII=y
-CONFIG_PWM_IMX=y
-CONFIG_SPI=y
-CONFIG_MXC_SPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_KEYBOARD=y
-CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Advantech"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0525
-CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
-CONFIG_CI_UDC=y
-CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_VIDEO_IPUV3=y
-CONFIG_VIDEO=y
-# CONFIG_VIDEO_SW_CURSOR is not set
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,233 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2016 Timesys Corporation
- * Copyright (C) 2016 Advantech Corporation
- * Copyright (C) 2012 Freescale Semiconductor, Inc.
- */
-
-#ifndef __ADVANTECH_DMSBA16_CONFIG_H
-#define __ADVANTECH_DMSBA16_CONFIG_H
-
-#include <asm/arch/imx-regs.h>
-#include <asm/mach-imx/gpio.h>
-
-#define CONFIG_BOARD_NAME "Advantech DMS-BA16"
-
-#define CONFIG_MXC_UART_BASE UART4_BASE
-#define CONSOLE_DEV "ttymxc3"
-#define CONFIG_EXTRA_BOOTARGS "panic=10"
-
-#define CONFIG_BOOT_DIR ""
-#define CONFIG_LOADCMD "fatload"
-#define CONFIG_RFSPART "2"
-
-#include "mx6_common.h"
-#include <linux/sizes.h>
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
-
-#define CONFIG_MXC_UART
-
-/* SATA Configs */
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
-#define CONFIG_DWC_AHSATA_PORT_ID 0
-#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
-#define CONFIG_LBA48
-
-/* MMC Configs */
-#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-
-/* USB Configs */
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS 0
-
-#define CONFIG_USBD_HS
-
-/* Networking Configs */
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_MXC_PHYADDR 4
-
-/* Serial Flash */
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_LOADADDR 0x12000000
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "script=boot.scr\0" \
- "image=" CONFIG_BOOT_DIR "/uImage\0" \
- "uboot=u-boot.imx\0" \
- "fdt_file=" CONFIG_BOOT_DIR "/" CONFIG_DEFAULT_FDT_FILE "\0" \
- "fdt_addr=0x18000000\0" \
- "boot_fdt=yes\0" \
- "ip_dyn=yes\0" \
- "console=" CONSOLE_DEV "\0" \
- "fdt_high=0xffffffff\0" \
- "initrd_high=0xffffffff\0" \
- "sddev=0\0" \
- "emmcdev=1\0" \
- "partnum=1\0" \
- "loadcmd=" CONFIG_LOADCMD "\0" \
- "rfspart=" CONFIG_RFSPART "\0" \
- "update_sd_firmware=" \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "if mmc dev ${mmcdev}; then " \
- "if ${get_cmd} ${update_sd_firmware_filename}; then " \
- "setexpr fw_sz ${filesize} / 0x200; " \
- "setexpr fw_sz ${fw_sz} + 1; " \
- "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
- "fi; " \
- "fi\0" \
- "update_sf_uboot=" \
- "if tftp $loadaddr $uboot; then " \
- "sf probe; " \
- "sf erase 0 0xC0000; " \
- "sf write $loadaddr 0x400 $filesize; " \
- "echo 'U-Boot upgraded. Please reset'; " \
- "fi\0" \
- "setargs=setenv bootargs console=${console},${baudrate} " \
- "root=/dev/${rootdev} rw rootwait " CONFIG_EXTRA_BOOTARGS "\0" \
- "loadbootscript=" \
- "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \
- "bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \
- " source\0" \
- "loadimage=" \
- "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
- "loadfdt=${loadcmd} ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \
- "tryboot=" \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loadimage; then " \
- "run doboot; " \
- "fi; " \
- "fi;\0" \
- "doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \
- "run setargs; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootm; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootm; " \
- "fi;\0" \
- "netargs=setenv bootargs console=${console},${baudrate} " \
- "root=/dev/nfs " \
- "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
- "netboot=echo Booting from net ...; " \
- "run netargs; " \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "${get_cmd} ${image}; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootm; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootm; " \
- "fi;\0" \
-
-#define CONFIG_BOOTCOMMAND \
- "usb start; " \
- "setenv dev usb; " \
- "setenv devnum 0; " \
- "setenv rootdev sda${rfspart}; " \
- "run tryboot; " \
- \
- "setenv dev mmc; " \
- "setenv rootdev mmcblk0p${rfspart}; " \
- \
- "setenv devnum ${sddev}; " \
- "if mmc dev ${devnum}; then " \
- "run tryboot; " \
- "fi; " \
- \
- "setenv devnum ${emmcdev}; " \
- "setenv rootdev mmcblk${emmcdev}p${rfspart}; " \
- "if mmc dev ${devnum}; then " \
- "run tryboot; " \
- "fi; " \
- \
- "bmode usb; " \
-
-#define CONFIG_ARP_TIMEOUT 200UL
-
-/* Miscellaneous configurable options */
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-
-/* Physical Memory Map */
-#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/* FLASH and environment organization */
-
-#define CONFIG_SYS_FSL_USDHC_NUM 3
-
-/* Framebuffer */
-#ifdef CONFIG_VIDEO
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_BMP_16BPP
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_IMX_HDMI
-#define CONFIG_IMX_VIDEO_SKIP
-#endif
-
-#define CONFIG_IMX6_PWM_PER_CLK 66000000
-
-#ifdef CONFIG_CMD_PCI
-#define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_PCIE_IMX
-#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12)
-#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(1, 5)
-#endif
-
-/* I2C Configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_MXC_I2C1
-#define CONFIG_SYS_I2C_MXC_I2C2
-#define CONFIG_SYS_I2C_MXC_I2C3
-
-#endif /* __ADVANTECH_DMSBA16_CONFIG_H */
OF_CONTROL, DM_SPI and other driver model migration deadlines are expired for this board. Remove it. Patch-cc: Akshay Bhat <akshaybhat at timesys.com> Patch-cc: Ken Lin <Ken.Lin at advantech.com.tw> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com> --- arch/arm/mach-imx/mx6/Kconfig | 7 - board/advantech/dms-ba16/Kconfig | 31 -- board/advantech/dms-ba16/MAINTAINERS | 8 - board/advantech/dms-ba16/Makefile | 6 - board/advantech/dms-ba16/clocks.cfg | 25 - board/advantech/dms-ba16/ddr-setup.cfg | 39 -- board/advantech/dms-ba16/dms-ba16.c | 629 ----------------------- board/advantech/dms-ba16/dms-ba16_1g.cfg | 24 - board/advantech/dms-ba16/dms-ba16_2g.cfg | 24 - board/advantech/dms-ba16/micron-1g.cfg | 63 --- board/advantech/dms-ba16/samsung-2g.cfg | 63 --- configs/dms-ba16-1g_defconfig | 64 --- configs/dms-ba16_defconfig | 63 --- include/configs/advantech_dms-ba16.h | 233 --------- 14 files changed, 1279 deletions(-) delete mode 100644 board/advantech/dms-ba16/Kconfig delete mode 100644 board/advantech/dms-ba16/MAINTAINERS delete mode 100644 board/advantech/dms-ba16/Makefile delete mode 100644 board/advantech/dms-ba16/clocks.cfg delete mode 100644 board/advantech/dms-ba16/ddr-setup.cfg delete mode 100644 board/advantech/dms-ba16/dms-ba16.c delete mode 100644 board/advantech/dms-ba16/dms-ba16_1g.cfg delete mode 100644 board/advantech/dms-ba16/dms-ba16_2g.cfg delete mode 100644 board/advantech/dms-ba16/micron-1g.cfg delete mode 100644 board/advantech/dms-ba16/samsung-2g.cfg delete mode 100644 configs/dms-ba16-1g_defconfig delete mode 100644 configs/dms-ba16_defconfig delete mode 100644 include/configs/advantech_dms-ba16.h