diff mbox series

[v3,2/4] arm: Remove d2net_v2 board

Message ID 20200618174516.239626-3-jagan@amarulasolutions.com
State New
Headers show
Series spi: kirkwood: dm-conversion (part4) | expand

Commit Message

Jagan Teki June 18, 2020, 5:45 p.m. UTC 
This board has not been converted to CONFIG_DM by the deadline.

Remove it.

Cc: Simon Guinot <simon.guinot at sequanux.org>
Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
---
Changes for v3:
- new patch

 arch/arm/mach-kirkwood/Kconfig      |   4 -
 board/LaCie/net2big_v2/Kconfig      |  12 --
 board/LaCie/net2big_v2/MAINTAINERS  |   7 -
 board/LaCie/net2big_v2/Makefile     |  13 --
 board/LaCie/net2big_v2/kwbimage.cfg | 149 ----------------
 board/LaCie/net2big_v2/net2big_v2.c | 257 ----------------------------
 board/LaCie/net2big_v2/net2big_v2.h |  28 ---
 configs/d2net_v2_defconfig          |  53 ------
 configs/net2big_v2_defconfig        |  53 ------
 include/configs/lacie_kw.h          | 152 ----------------
 10 files changed, 728 deletions(-)
 delete mode 100644 board/LaCie/net2big_v2/Kconfig
 delete mode 100644 board/LaCie/net2big_v2/MAINTAINERS
 delete mode 100644 board/LaCie/net2big_v2/Makefile
 delete mode 100644 board/LaCie/net2big_v2/kwbimage.cfg
 delete mode 100644 board/LaCie/net2big_v2/net2big_v2.c
 delete mode 100644 board/LaCie/net2big_v2/net2big_v2.h
 delete mode 100644 configs/d2net_v2_defconfig
 delete mode 100644 configs/net2big_v2_defconfig
 delete mode 100644 include/configs/lacie_kw.h

Comments

Simon Guinot June 18, 2020, 10:02 p.m. UTC | #1 
On Thu, Jun 18, 2020 at 11:15:14PM +0530, Jagan Teki wrote:
Hi Jagan,

> This board has not been converted to CONFIG_DM by the deadline.

Is that possible to negociate a new deadline ?

Thanks in advance.

Simon

> 
> Remove it.
> 
> Cc: Simon Guinot <simon.guinot at sequanux.org>
> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
> ---
> Changes for v3:
> - new patch
> 
>  arch/arm/mach-kirkwood/Kconfig      |   4 -
>  board/LaCie/net2big_v2/Kconfig      |  12 --
>  board/LaCie/net2big_v2/MAINTAINERS  |   7 -
>  board/LaCie/net2big_v2/Makefile     |  13 --
>  board/LaCie/net2big_v2/kwbimage.cfg | 149 ----------------
>  board/LaCie/net2big_v2/net2big_v2.c | 257 ----------------------------
>  board/LaCie/net2big_v2/net2big_v2.h |  28 ---
>  configs/d2net_v2_defconfig          |  53 ------
>  configs/net2big_v2_defconfig        |  53 ------
>  include/configs/lacie_kw.h          | 152 ----------------
>  10 files changed, 728 deletions(-)
>  delete mode 100644 board/LaCie/net2big_v2/Kconfig
>  delete mode 100644 board/LaCie/net2big_v2/MAINTAINERS
>  delete mode 100644 board/LaCie/net2big_v2/Makefile
>  delete mode 100644 board/LaCie/net2big_v2/kwbimage.cfg
>  delete mode 100644 board/LaCie/net2big_v2/net2big_v2.c
>  delete mode 100644 board/LaCie/net2big_v2/net2big_v2.h
>  delete mode 100644 configs/d2net_v2_defconfig
>  delete mode 100644 configs/net2big_v2_defconfig
>  delete mode 100644 include/configs/lacie_kw.h
> 
> diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
> index ae44cb665e..ad6aef45bf 100644
> --- a/arch/arm/mach-kirkwood/Kconfig
> +++ b/arch/arm/mach-kirkwood/Kconfig
> @@ -35,9 +35,6 @@ config TARGET_KM_KIRKWOOD
>  	bool "KM Kirkwood Board"
>  	select VENDOR_KM
>  
> -config TARGET_NET2BIG_V2
> -	bool "LaCie 2Big Network v2 NAS Board"
> -
>  config TARGET_NETSPACE_V2
>  	bool "LaCie netspace_v2 Board"
>  
> @@ -80,7 +77,6 @@ source "board/cloudengines/pogo_e02/Kconfig"
>  source "board/d-link/dns325/Kconfig"
>  source "board/iomega/iconnect/Kconfig"
>  source "board/keymile/Kconfig"
> -source "board/LaCie/net2big_v2/Kconfig"
>  source "board/LaCie/netspace_v2/Kconfig"
>  source "board/raidsonic/ib62x0/Kconfig"
>  source "board/Seagate/dockstar/Kconfig"
> diff --git a/board/LaCie/net2big_v2/Kconfig b/board/LaCie/net2big_v2/Kconfig
> deleted file mode 100644
> index ba460dba45..0000000000
> --- a/board/LaCie/net2big_v2/Kconfig
> +++ /dev/null
> @@ -1,12 +0,0 @@
> -if TARGET_NET2BIG_V2
> -
> -config SYS_BOARD
> -	default "net2big_v2"
> -
> -config SYS_VENDOR
> -	default "LaCie"
> -
> -config SYS_CONFIG_NAME
> -	default "lacie_kw"
> -
> -endif
> diff --git a/board/LaCie/net2big_v2/MAINTAINERS b/board/LaCie/net2big_v2/MAINTAINERS
> deleted file mode 100644
> index 8fec70315f..0000000000
> --- a/board/LaCie/net2big_v2/MAINTAINERS
> +++ /dev/null
> @@ -1,7 +0,0 @@
> -NET2BIG_V2 BOARD
> -M:	Simon Guinot <simon.guinot at sequanux.org>
> -S:	Maintained
> -F:	board/LaCie/net2big_v2/
> -F:	include/configs/lacie_kw.h
> -F:	configs/d2net_v2_defconfig
> -F:	configs/net2big_v2_defconfig
> diff --git a/board/LaCie/net2big_v2/Makefile b/board/LaCie/net2big_v2/Makefile
> deleted file mode 100644
> index 3d12b72812..0000000000
> --- a/board/LaCie/net2big_v2/Makefile
> +++ /dev/null
> @@ -1,13 +0,0 @@
> -# SPDX-License-Identifier: GPL-2.0+
> -#
> -# Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
> -#
> -# Based on Kirkwood support:
> -# (C) Copyright 2009
> -# Marvell Semiconductor <www.marvell.com>
> -# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
> -
> -obj-y	:= net2big_v2.o ../common/common.o
> -ifneq ($(and $(CONFIG_KIRKWOOD_GPIO),$(CONFIG_NET2BIG_V2)),)
> -obj-y	+= ../common/cpld-gpio-bus.o
> -endif
> diff --git a/board/LaCie/net2big_v2/kwbimage.cfg b/board/LaCie/net2big_v2/kwbimage.cfg
> deleted file mode 100644
> index 3897a1197a..0000000000
> --- a/board/LaCie/net2big_v2/kwbimage.cfg
> +++ /dev/null
> @@ -1,149 +0,0 @@
> -# SPDX-License-Identifier: GPL-2.0+
> -#
> -# Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
> -#
> -# Based on Kirkwood support:
> -# (C) Copyright 2009
> -# Marvell Semiconductor <www.marvell.com>
> -# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
> -# Refer doc/README.kwbimage for more details about how-to configure
> -# and create kirkwood boot image
> -#
> -
> -# Boot Media configurations
> -BOOT_FROM	spi	# Boot from SPI flash
> -
> -# SOC registers configuration using bootrom header extension
> -# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
> -
> -# Configure RGMII-0 interface pad voltage to 1.8V
> -DATA 0xFFD100e0 0x1B1B1B9B
> -
> -#Dram initalization for SINGLE x16 CL=5 @ 400MHz
> -DATA 0xFFD01400 0x43000C30	# DDR Configuration register
> -# bit13-0:  0xa00 (2560 DDR2 clks refresh rate)
> -# bit23-14: zero
> -# bit24: 1= enable exit self refresh mode on DDR access
> -# bit25: 1 required
> -# bit29-26: zero
> -# bit31-30: 01
> -
> -DATA 0xFFD01404 0x38743000	# DDR Controller Control Low
> -# bit 4:    0=addr/cmd in smame cycle
> -# bit 5:    0=clk is driven during self refresh, we don't care for APX
> -# bit 6:    0=use recommended falling edge of clk for addr/cmd
> -# bit14:    0=input buffer always powered up
> -# bit18:    1=cpu lock transaction enabled
> -# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
> -# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
> -# bit30-28: 3 required
> -# bit31:    0=no additional STARTBURST delay
> -
> -DATA 0xFFD01408 0x22125451	# DDR Timing (Low) (active cycles value +1)
> -# bit7-4:   TRCD
> -# bit11- 8: TRP
> -# bit15-12: TWR
> -# bit19-16: TWTR
> -# bit20:    TRAS msb
> -# bit23-21: 0x0
> -# bit27-24: TRRD
> -# bit31-28: TRTP
> -
> -DATA 0xFFD0140C 0x00000A32	#  DDR Timing (High)
> -# bit6-0:   TRFC
> -# bit8-7:   TR2R
> -# bit10-9:  TR2W
> -# bit12-11: TW2W
> -# bit31-13: zero required
> -
> -DATA 0xFFD01410 0x0000CCCC	#  DDR Address Control
> -# bit1-0:   01, Cs0width=x16
> -# bit3-2:   11, Cs0size=1Gb
> -# bit5-4:   00, Cs2width=nonexistent
> -# bit7-6:   00, Cs1size =nonexistent
> -# bit9-8:   00, Cs2width=nonexistent
> -# bit11-10: 00, Cs2size =nonexistent
> -# bit13-12: 00, Cs3width=nonexistent
> -# bit15-14: 00, Cs3size =nonexistent
> -# bit16:    0,  Cs0AddrSel
> -# bit17:    0,  Cs1AddrSel
> -# bit18:    0,  Cs2AddrSel
> -# bit19:    0,  Cs3AddrSel
> -# bit31-20: 0 required
> -
> -DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
> -# bit0:    0,  OpenPage enabled
> -# bit31-1: 0 required
> -
> -DATA 0xFFD01418 0x00000000	#  DDR Operation
> -# bit3-0:   0x0, DDR cmd
> -# bit31-4:  0 required
> -
> -DATA 0xFFD0141C 0x00000662	#  DDR Mode
> -# bit2-0:   2, BurstLen=2 required
> -# bit3:     0, BurstType=0 required
> -# bit6-4:   4, CL=5
> -# bit7:     0, TestMode=0 normal
> -# bit8:     0, DLL reset=0 normal
> -# bit11-9:  6, auto-precharge write recovery ????????????
> -# bit12:    0, PD must be zero
> -# bit31-13: 0 required
> -
> -DATA 0xFFD01420 0x00000044	#  DDR Extended Mode
> -# bit0:    0,  DDR DLL enabled
> -# bit1:    1,  DDR drive strenght reduced
> -# bit2:    1,  DDR ODT control lsd enabled
> -# bit5-3:  000, required
> -# bit6:    1,  DDR ODT control msb, enabled
> -# bit9-7:  000, required
> -# bit10:   0,  differential DQS enabled
> -# bit11:   0, required
> -# bit12:   0, DDR output buffer enabled
> -# bit31-13: 0 required
> -
> -DATA 0xFFD01424 0x0000F17F	#  DDR Controller Control High
> -# bit2-0:  111, required
> -# bit3  :  1  , MBUS Burst Chop disabled
> -# bit6-4:  111, required
> -# bit7  :  1  , D2P Latency enabled
> -# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
> -# bit9  :  0  , no half clock cycle addition to dataout
> -# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
> -# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
> -# bit15-12: 1111 required
> -# bit31-16: 0    required
> -
> -DATA 0xFFD01428 0x00096630	# DDR2 ODT Read Timing (default values)
> -DATA 0xFFD0147C 0x00009663	# DDR2 ODT Write Timing (default values)
> -
> -DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
> -DATA 0xFFD01504 0x0FFFFFF1	# CS[0]n Size
> -# bit0:    1,  Window enabled
> -# bit1:    0,  Write Protect disabled
> -# bit3-2:  00, CS0 hit selected
> -# bit23-4: ones, required
> -# bit31-24: 0x07, Size (i.e. 128MB)
> -
> -DATA 0xFFD0150C 0x00000000	# CS[1]n Size, window disabled
> -DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
> -DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
> -
> -DATA 0xFFD01494 0x00010000	#  DDR ODT Control (Low)
> -# bit3-0:  1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
> -# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
> -
> -DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
> -# bit1-0:  00, ODT0 controlled by ODT Control (low) register above
> -# bit3-2:  01, ODT1 active NEVER!
> -# bit31-4: zero, required
> -
> -DATA 0xFFD0149C 0x0000E40F	# CPU ODT Control
> -# bit3-0:  1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
> -# bit7-4:  1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
> -# bit11-10:1, DQ_ODTSel. ODT select turned on
> -
> -DATA 0xFFD01480 0x00000001	# DDR Initialization Control
> -#bit0=1, enable DDR init upon this register write
> -
> -# End of Header extension
> -DATA 0x0 0x0
> diff --git a/board/LaCie/net2big_v2/net2big_v2.c b/board/LaCie/net2big_v2/net2big_v2.c
> deleted file mode 100644
> index dbd8b5755d..0000000000
> --- a/board/LaCie/net2big_v2/net2big_v2.c
> +++ /dev/null
> @@ -1,257 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0+
> -/*
> - * Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
> - *
> - * Based on Kirkwood support:
> - * (C) Copyright 2009
> - * Marvell Semiconductor <www.marvell.com>
> - * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
> - */
> -
> -#include <common.h>
> -#include <command.h>
> -#include <env.h>
> -#include <i2c.h>
> -#include <init.h>
> -#include <net.h>
> -#include <asm/mach-types.h>
> -#include <asm/arch/cpu.h>
> -#include <asm/arch/soc.h>
> -#include <asm/arch/mpp.h>
> -#include <asm/arch/gpio.h>
> -
> -#include "net2big_v2.h"
> -#include "../common/common.h"
> -#include "../common/cpld-gpio-bus.h"
> -
> -DECLARE_GLOBAL_DATA_PTR;
> -
> -int board_early_init_f(void)
> -{
> -	/* GPIO configuration */
> -	mvebu_config_gpio(NET2BIG_V2_OE_VAL_LOW, NET2BIG_V2_OE_VAL_HIGH,
> -			  NET2BIG_V2_OE_LOW, NET2BIG_V2_OE_HIGH);
> -
> -	/* Multi-Purpose Pins Functionality configuration */
> -	static const u32 kwmpp_config[] = {
> -		MPP0_SPI_SCn,
> -		MPP1_SPI_MOSI,
> -		MPP2_SPI_SCK,
> -		MPP3_SPI_MISO,
> -		MPP6_SYSRST_OUTn,
> -		MPP7_GPO,		/* Request power-off */
> -		MPP8_TW_SDA,
> -		MPP9_TW_SCK,
> -		MPP10_UART0_TXD,
> -		MPP11_UART0_RXD,
> -		MPP13_GPIO,		/* Rear power switch (on|auto) */
> -		MPP14_GPIO,		/* USB fuse alarm */
> -		MPP15_GPIO,		/* Rear power switch (auto|off) */
> -		MPP16_GPIO,		/* SATA HDD1 power */
> -		MPP17_GPIO,		/* SATA HDD2 power */
> -		MPP20_SATA1_ACTn,
> -		MPP21_SATA0_ACTn,
> -		MPP24_GPIO,		/* USB mode select */
> -		MPP26_GPIO,		/* USB device vbus */
> -		MPP28_GPIO,		/* USB enable host vbus */
> -		MPP29_GPIO,		/* CPLD GPIO bus ALE */
> -		MPP34_GPIO,		/* Rear Push button 0=on 1=off */
> -		MPP35_GPIO,		/* Inhibit switch power-off */
> -		MPP36_GPIO,		/* SATA HDD1 presence */
> -		MPP37_GPIO,		/* SATA HDD2 presence */
> -		MPP40_GPIO,		/* eSATA presence */
> -		MPP44_GPIO,		/* CPLD GPIO bus (data 0) */
> -		MPP45_GPIO,		/* CPLD GPIO bus (data 1) */
> -		MPP46_GPIO,		/* CPLD GPIO bus (data 2) */
> -		MPP47_GPIO,		/* CPLD GPIO bus (addr 0) */
> -		MPP48_GPIO,		/* CPLD GPIO bus (addr 1) */
> -		MPP49_GPIO,		/* CPLD GPIO bus (addr 2) */
> -		0
> -	};
> -
> -	kirkwood_mpp_conf(kwmpp_config, NULL);
> -
> -	return 0;
> -}
> -
> -int board_init(void)
> -{
> -	/* Machine number */
> -	gd->bd->bi_arch_number = MACH_TYPE_NET2BIG_V2;
> -
> -	/* Boot parameters address */
> -	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
> -
> -	return 0;
> -}
> -
> -#if defined(CONFIG_MISC_INIT_R)
> -
> -#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_G762_ADDR)
> -/*
> - * Start I2C fan (GMT G762 controller)
> - */
> -static void init_fan(void)
> -{
> -	u8 data;
> -
> -	i2c_set_bus_num(0);
> -
> -	/* Enable open-loop and PWM modes */
> -	data = 0x20;
> -	if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
> -		      G762_REG_FAN_CMD1, 1, &data, 1) != 0)
> -		goto err;
> -	data = 0;
> -	if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
> -		      G762_REG_SET_CNT, 1, &data, 1) != 0)
> -		goto err;
> -	/*
> -	 * RPM to PWM (set_out register) fan speed conversion array:
> -	 * 0    0x00
> -	 * 1500	0x04
> -	 * 2800	0x08
> -	 * 3400	0x0C
> -	 * 3700	0x10
> -	 * 4400	0x20
> -	 * 4700	0x30
> -	 * 4800	0x50
> -	 * 5200	0x80
> -	 * 5400	0xC0
> -	 * 5500	0xFF
> -	 *
> -	 * Start fan at low speed (2800 RPM):
> -	 */
> -	data = 0x08;
> -	if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
> -		      G762_REG_SET_OUT, 1, &data, 1) != 0)
> -		goto err;
> -
> -	return;
> -err:
> -	printf("Error: failed to start I2C fan @%02x\n",
> -	       CONFIG_SYS_I2C_G762_ADDR);
> -}
> -#else
> -static void init_fan(void) {}
> -#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_G762_ADDR */
> -
> -#if defined(CONFIG_NET2BIG_V2) && defined(CONFIG_KIRKWOOD_GPIO)
> -/*
> - * CPLD GPIO bus:
> - *
> - * - address register : bit [0-2] -> GPIO [47-49]
> - * - data register    : bit [0-2] -> GPIO [44-46]
> - * - enable register  : GPIO 29
> - */
> -static unsigned cpld_gpio_bus_addr[] = { 47, 48, 49 };
> -static unsigned cpld_gpio_bus_data[] = { 44, 45, 46 };
> -
> -static struct cpld_gpio_bus cpld_gpio_bus = {
> -	.addr		= cpld_gpio_bus_addr,
> -	.num_addr	= ARRAY_SIZE(cpld_gpio_bus_addr),
> -	.data		= cpld_gpio_bus_data,
> -	.num_data	= ARRAY_SIZE(cpld_gpio_bus_data),
> -	.enable		= 29,
> -};
> -
> -/*
> - * LEDs configuration:
> - *
> - * The LEDs are controlled by a CPLD and can be configured through
> - * the CPLD GPIO bus.
> - *
> - * Address register selection:
> - *
> - * addr | register
> - * ----------------------------
> - *   0  | front LED
> - *   1  | front LED brightness
> - *   2  | SATA LED brightness
> - *   3  | SATA0 LED
> - *   4  | SATA1 LED
> - *   5  | SATA2 LED
> - *   6  | SATA3 LED
> - *   7  | SATA4 LED
> - *
> - * Data register configuration:
> - *
> - * data | LED brightness
> - * -------------------------------------------------
> - *   0  | min (off)
> - *   -  | -
> - *   7  | max
> - *
> - * data | front LED mode
> - * -------------------------------------------------
> - *   0  | fix off
> - *   1  | fix blue on
> - *   2  | fix red on
> - *   3  | blink blue on=1 sec and blue off=1 sec
> - *   4  | blink red on=1 sec and red off=1 sec
> - *   5  | blink blue on=2.5 sec and red on=0.5 sec
> - *   6  | blink blue on=1 sec and red on=1 sec
> - *   7  | blink blue on=0.5 sec and blue off=2.5 sec
> - *
> - * data | SATA LED mode
> - * -------------------------------------------------
> - *   0  | fix off
> - *   1  | SATA activity blink
> - *   2  | fix red on
> - *   3  | blink blue on=1 sec and blue off=1 sec
> - *   4  | blink red on=1 sec and red off=1 sec
> - *   5  | blink blue on=2.5 sec and red on=0.5 sec
> - *   6  | blink blue on=1 sec and red on=1 sec
> - *   7  | fix blue on
> - */
> -static void init_leds(void)
> -{
> -	/* Enable the front blue LED */
> -	cpld_gpio_bus_write(&cpld_gpio_bus, 0, 1);
> -	cpld_gpio_bus_write(&cpld_gpio_bus, 1, 3);
> -
> -	/* Configure SATA LEDs to blink in relation with the SATA activity */
> -	cpld_gpio_bus_write(&cpld_gpio_bus, 3, 1);
> -	cpld_gpio_bus_write(&cpld_gpio_bus, 4, 1);
> -	cpld_gpio_bus_write(&cpld_gpio_bus, 2, 3);
> -}
> -#else
> -static void init_leds(void) {}
> -#endif /* CONFIG_NET2BIG_V2 && CONFIG_KIRKWOOD_GPIO */
> -
> -int misc_init_r(void)
> -{
> -	init_fan();
> -#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
> -	if (!env_get("ethaddr")) {
> -		uchar mac[6];
> -		if (lacie_read_mac_address(mac) == 0)
> -			eth_env_set_enetaddr("ethaddr", mac);
> -	}
> -#endif
> -	init_leds();
> -
> -	return 0;
> -}
> -#endif /* CONFIG_MISC_INIT_R */
> -
> -#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
> -/* Configure and initialize PHY */
> -void reset_phy(void)
> -{
> -	mv_phy_88e1116_init("egiga0", 8);
> -}
> -#endif
> -
> -#if defined(CONFIG_KIRKWOOD_GPIO)
> -/* Return GPIO push button status */
> -static int
> -do_read_push_button(struct cmd_tbl *cmdtp, int flag, int argc,
> -		    char *const argv[])
> -{
> -	return !kw_gpio_get_value(NET2BIG_V2_GPIO_PUSH_BUTTON);
> -}
> -
> -U_BOOT_CMD(button, 1, 1, do_read_push_button,
> -	   "Return GPIO push button status 0=off 1=on", "");
> -#endif
> diff --git a/board/LaCie/net2big_v2/net2big_v2.h b/board/LaCie/net2big_v2/net2big_v2.h
> deleted file mode 100644
> index d61dd0e998..0000000000
> --- a/board/LaCie/net2big_v2/net2big_v2.h
> +++ /dev/null
> @@ -1,28 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0+ */
> -/*
> - * Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
> - *
> - * Based on Kirkwood support:
> - * (C) Copyright 2009
> - * Marvell Semiconductor <www.marvell.com>
> - * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
> - */
> -
> -#ifndef NET2BIG_V2_H
> -#define NET2BIG_V2_H
> -
> -/* GPIO configuration */
> -#define NET2BIG_V2_OE_LOW		0x0600E000
> -#define NET2BIG_V2_OE_HIGH		0x00000134
> -#define NET2BIG_V2_OE_VAL_LOW		0x10030000
> -#define NET2BIG_V2_OE_VAL_HIGH		0x00000000
> -
> -/* Buttons */
> -#define NET2BIG_V2_GPIO_PUSH_BUTTON	34
> -
> -/* GMT G762 registers (I2C fan controller) */
> -#define G762_REG_SET_CNT		0x00
> -#define G762_REG_SET_OUT		0x03
> -#define G762_REG_FAN_CMD1		0x04
> -
> -#endif /* NET2BIG_V2_H */
> diff --git a/configs/d2net_v2_defconfig b/configs/d2net_v2_defconfig
> deleted file mode 100644
> index fe3c6c4762..0000000000
> --- a/configs/d2net_v2_defconfig
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -CONFIG_ARM=y
> -CONFIG_SYS_DCACHE_OFF=y
> -CONFIG_ARCH_CPU_INIT=y
> -CONFIG_ARCH_KIRKWOOD=y
> -CONFIG_SYS_TEXT_BASE=0x600000
> -CONFIG_TARGET_NET2BIG_V2=y
> -CONFIG_ENV_SIZE=0x1000
> -CONFIG_ENV_OFFSET=0x70000
> -CONFIG_ENV_SECT_SIZE=0x10000
> -CONFIG_NR_DRAM_BANKS=2
> -CONFIG_IDENT_STRING=" D2 v2"
> -CONFIG_SYS_EXTRA_OPTIONS="D2NET_V2"
> -CONFIG_BOOTDELAY=3
> -CONFIG_USE_BOOTARGS=y
> -CONFIG_BOOTARGS="console=ttyS0,115200"
> -CONFIG_USE_PREBOOT=y
> -CONFIG_CONSOLE_MUX=y
> -CONFIG_MISC_INIT_R=y
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_SYS_PROMPT="d2v2> "
> -CONFIG_CMD_EEPROM=y
> -CONFIG_CMD_IDE=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_SF=y
> -CONFIG_CMD_USB=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_DHCP=y
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -CONFIG_CMD_EXT2=y
> -CONFIG_CMD_FAT=y
> -CONFIG_ISO_PARTITION=y
> -CONFIG_EFI_PARTITION=y
> -# CONFIG_PARTITION_UUIDS is not set
> -CONFIG_OF_CONTROL=y
> -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-d2net"
> -CONFIG_ENV_IS_IN_SPI_FLASH=y
> -CONFIG_USE_ENV_SPI_MAX_HZ=y
> -CONFIG_ENV_SPI_MAX_HZ=20000000
> -CONFIG_ENV_ADDR=0x70000
> -CONFIG_MVSATA_IDE=y
> -# CONFIG_MMC is not set
> -CONFIG_SPI_FLASH=y
> -CONFIG_SPI_FLASH_MACRONIX=y
> -CONFIG_MVGBE=y
> -CONFIG_MII=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_SPI=y
> -CONFIG_KIRKWOOD_SPI=y
> -CONFIG_USB=y
> -CONFIG_USB_EHCI_HCD=y
> -CONFIG_USB_STORAGE=y
> diff --git a/configs/net2big_v2_defconfig b/configs/net2big_v2_defconfig
> deleted file mode 100644
> index 1389d30900..0000000000
> --- a/configs/net2big_v2_defconfig
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -CONFIG_ARM=y
> -CONFIG_SYS_DCACHE_OFF=y
> -CONFIG_ARCH_CPU_INIT=y
> -CONFIG_ARCH_KIRKWOOD=y
> -CONFIG_SYS_TEXT_BASE=0x600000
> -CONFIG_TARGET_NET2BIG_V2=y
> -CONFIG_ENV_SIZE=0x1000
> -CONFIG_ENV_OFFSET=0x70000
> -CONFIG_ENV_SECT_SIZE=0x10000
> -CONFIG_NR_DRAM_BANKS=2
> -CONFIG_IDENT_STRING=" 2Big v2"
> -CONFIG_SYS_EXTRA_OPTIONS="NET2BIG_V2"
> -CONFIG_BOOTDELAY=3
> -CONFIG_USE_BOOTARGS=y
> -CONFIG_BOOTARGS="console=ttyS0,115200"
> -CONFIG_USE_PREBOOT=y
> -CONFIG_CONSOLE_MUX=y
> -CONFIG_MISC_INIT_R=y
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_SYS_PROMPT="2big2> "
> -CONFIG_CMD_EEPROM=y
> -CONFIG_CMD_IDE=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_SF=y
> -CONFIG_CMD_USB=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_DHCP=y
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -CONFIG_CMD_EXT2=y
> -CONFIG_CMD_FAT=y
> -CONFIG_ISO_PARTITION=y
> -CONFIG_EFI_PARTITION=y
> -# CONFIG_PARTITION_UUIDS is not set
> -CONFIG_OF_CONTROL=y
> -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-net2big"
> -CONFIG_ENV_IS_IN_SPI_FLASH=y
> -CONFIG_USE_ENV_SPI_MAX_HZ=y
> -CONFIG_ENV_SPI_MAX_HZ=20000000
> -CONFIG_ENV_ADDR=0x70000
> -CONFIG_MVSATA_IDE=y
> -# CONFIG_MMC is not set
> -CONFIG_SPI_FLASH=y
> -CONFIG_SPI_FLASH_MACRONIX=y
> -CONFIG_MVGBE=y
> -CONFIG_MII=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_SPI=y
> -CONFIG_KIRKWOOD_SPI=y
> -CONFIG_USB=y
> -CONFIG_USB_EHCI_HCD=y
> -CONFIG_USB_STORAGE=y
> diff --git a/include/configs/lacie_kw.h b/include/configs/lacie_kw.h
> deleted file mode 100644
> index 5bb0255a74..0000000000
> --- a/include/configs/lacie_kw.h
> +++ /dev/null
> @@ -1,152 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0+ */
> -/*
> - * Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
> - */
> -
> -#ifndef _CONFIG_LACIE_KW_H
> -#define _CONFIG_LACIE_KW_H
> -
> -/*
> - * Machine number definition
> - */
> -#if defined(CONFIG_INETSPACE_V2)
> -#define CONFIG_MACH_TYPE		MACH_TYPE_INETSPACE_V2
> -#elif defined(CONFIG_NETSPACE_V2)
> -#define CONFIG_MACH_TYPE		MACH_TYPE_NETSPACE_V2
> -#elif defined(CONFIG_NETSPACE_LITE_V2)
> -#define CONFIG_MACH_TYPE		MACH_TYPE_NETSPACE_LITE_V2
> -#elif defined(CONFIG_NETSPACE_MINI_V2)
> -#define CONFIG_MACH_TYPE		MACH_TYPE_NETSPACE_MINI_V2
> -#elif defined(CONFIG_NETSPACE_MAX_V2)
> -#define CONFIG_MACH_TYPE		MACH_TYPE_NETSPACE_MAX_V2
> -#elif defined(CONFIG_D2NET_V2)
> -#define CONFIG_MACH_TYPE		MACH_TYPE_D2NET_V2
> -#elif defined(CONFIG_NET2BIG_V2)
> -#define CONFIG_MACH_TYPE		MACH_TYPE_NET2BIG_V2
> -#else
> -#error "Unknown board"
> -#endif
> -
> -/*
> - * High Level Configuration Options (easy to change)
> - */
> -#define CONFIG_FEROCEON_88FR131		/* CPU Core subversion */
> -/* SoC name */
> -#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
> -#define CONFIG_KW88F6192
> -#else
> -#define CONFIG_KW88F6281
> -#endif
> -#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
> -
> -/*
> - * Core clock definition
> - */
> -#define CONFIG_SYS_TCLK			166000000 /* 166MHz */
> -
> -/*
> - * SDRAM configuration
> - */
> -
> -/*
> - * Different SDRAM configuration and size for some of the boards derived
> - * from the Network Space v2
> - */
> -#if defined(CONFIG_INETSPACE_V2)
> -#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-is2.cfg
> -#elif defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
> -#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-ns2l.cfg
> -#endif
> -
> -/*
> - * mv-common.h should be defined after CMD configs since it used them
> - * to enable certain macros
> - */
> -#include "mv-common.h"
> -
> -/* Remove or override few declarations from mv-common.h */
> -#undef CONFIG_SYS_IDE_MAXBUS
> -#undef CONFIG_SYS_IDE_MAXDEVICE
> -
> -/*
> - * Enable platform initialisation via misc_init_r() function
> - */
> -
> -/*
> - * Ethernet Driver configuration
> - */
> -#ifdef CONFIG_CMD_NET
> -#define CONFIG_MVGBE_PORTS		{1, 0} /* enable port 0 only */
> -#define CONFIG_NETCONSOLE
> -#endif
> -
> -/*
> - * SATA Driver configuration
> - */
> -#ifdef CONFIG_MVSATA_IDE
> -#define CONFIG_SYS_ATA_IDE0_OFFSET      MV_SATA_PORT0_OFFSET
> -#if defined(CONFIG_NETSPACE_MAX_V2) || defined(CONFIG_D2NET_V2) || \
> -	defined(CONFIG_NET2BIG_V2)
> -#define CONFIG_SYS_ATA_IDE1_OFFSET      MV_SATA_PORT1_OFFSET
> -#define CONFIG_SYS_IDE_MAXBUS           2
> -#define CONFIG_SYS_IDE_MAXDEVICE        2
> -#else
> -#define CONFIG_SYS_IDE_MAXBUS           1
> -#define CONFIG_SYS_IDE_MAXDEVICE        1
> -#endif
> -#endif /* CONFIG_MVSATA_IDE */
> -
> -/*
> - * Enable GPI0 support
> - */
> -#define CONFIG_KIRKWOOD_GPIO
> -
> -/*
> - * Enable I2C support
> - */
> -#ifdef CONFIG_CMD_I2C
> -/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4 /* 16-byte page size */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1 /* 8-bit device address */
> -#if defined(CONFIG_NET2BIG_V2)
> -#define CONFIG_SYS_I2C_G762_ADDR		0x3e
> -#endif
> -#endif /* CONFIG_CMD_I2C */
> -
> -/*
> - * Partition support
> - */
> -
> -/*
> - * File systems support
> - */
> -
> -/*
> - * Environment variables configurations
> - */
> -
> -/*
> - * Default environment variables
> - */
> -#define CONFIG_BOOTCOMMAND					\
> -	"dhcp && run netconsole; "				\
> -	"if run usbload || run diskload; then bootm; fi"
> -
> -#define CONFIG_EXTRA_ENV_SETTINGS				\
> -	"stdin=serial\0"					\
> -	"stdout=serial\0"					\
> -	"stderr=serial\0"					\
> -	"bootfile=uImage\0"					\
> -	"loadaddr=0x800000\0"					\
> -	"autoload=no\0"						\
> -	"netconsole="						\
> -		"set stdin $stdin,nc; "				\
> -		"set stdout $stdout,nc; "			\
> -		"set stderr $stderr,nc;\0"			\
> -	"diskload=ide reset && "				\
> -		"ext2load ide 0:1 $loadaddr /boot/$bootfile\0"	\
> -	"usbload=usb start && "					\
> -		"fatload usb 0:1 $loadaddr /boot/$bootfile\0"
> -
> -#endif /* _CONFIG_LACIE_KW_H */
> -- 
> 2.25.1
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200619/7f85313c/attachment.sig>
Tom Rini June 18, 2020, 10:25 p.m. UTC | #2 
On Fri, Jun 19, 2020 at 12:02:17AM +0200, Simon Guinot wrote:
> On Thu, Jun 18, 2020 at 11:15:14PM +0530, Jagan Teki wrote:
> Hi Jagan,
> 
> > This board has not been converted to CONFIG_DM by the deadline.
> 
> Is that possible to negociate a new deadline ?

Well, when will you be able to spend some time bringing the platform up
to current standards?  Doing a quick build for net2big_v2 I see:
+(net2big_v2) ===================== WARNING ======================
+(net2big_v2) This board does not use CONFIG_DM. CONFIG_DM will be
+(net2big_v2) compulsory starting with the v2020.01 release.
+(net2big_v2) Failure to update may result in board removal.
+(net2big_v2) See doc/driver-model/migration.rst for more info.
+(net2big_v2) ====================================================
+(net2big_v2) This board does not use CONFIG_DM_USB. Please update
+(net2big_v2) the board to use CONFIG_DM_USB before the v2019.07 release.
+(net2big_v2) Failure to update by the deadline may result in board removal.
+(net2big_v2) This board does use CONFIG_MVSATA_IDE which is not
+(net2big_v2) ported to driver-model (DM) yet. Please update the storage
+(net2big_v2) controller driver to use CONFIG_AHCI before the v2019.07
+(net2big_v2) release.
+(net2big_v2) This board does not use CONFIG_DM_SPI_FLASH. Please update
+(net2big_v2) the board to use CONFIG_SPI_FLASH before the v2019.07 release.
+(net2big_v2) This board does not use CONFIG_DM_ETH (Driver Model
+(net2big_v2) for Ethernet drivers). Please update the board to use
+(net2big_v2) CONFIG_DM_ETH before the v2020.07 release. Failure to
+(net2big_v2) update by the deadline may result in board removal.

So there's a lot of stuff that needs updating.  Conversion to CONFIG_DM
is what you'll need to then convert SPI, ETH and USB to use DM and the
IDE driver also needs attention and conversion.  Thanks!
Simon Guinot June 20, 2020, 12:24 a.m. UTC | #3 
On Thu, Jun 18, 2020 at 06:25:06PM -0400, Tom Rini wrote:
> On Fri, Jun 19, 2020 at 12:02:17AM +0200, Simon Guinot wrote:
> > On Thu, Jun 18, 2020 at 11:15:14PM +0530, Jagan Teki wrote:
> > Hi Jagan,
> > 
> > > This board has not been converted to CONFIG_DM by the deadline.
> > 
> > Is that possible to negociate a new deadline ?
> 
> Well, when will you be able to spend some time bringing the platform up
> to current standards?  Doing a quick build for net2big_v2 I see:
> +(net2big_v2) ===================== WARNING ======================
> +(net2big_v2) This board does not use CONFIG_DM. CONFIG_DM will be
> +(net2big_v2) compulsory starting with the v2020.01 release.
> +(net2big_v2) Failure to update may result in board removal.
> +(net2big_v2) See doc/driver-model/migration.rst for more info.
> +(net2big_v2) ====================================================
> +(net2big_v2) This board does not use CONFIG_DM_USB. Please update
> +(net2big_v2) the board to use CONFIG_DM_USB before the v2019.07 release.
> +(net2big_v2) Failure to update by the deadline may result in board removal.
> +(net2big_v2) This board does use CONFIG_MVSATA_IDE which is not
> +(net2big_v2) ported to driver-model (DM) yet. Please update the storage
> +(net2big_v2) controller driver to use CONFIG_AHCI before the v2019.07
> +(net2big_v2) release.
> +(net2big_v2) This board does not use CONFIG_DM_SPI_FLASH. Please update
> +(net2big_v2) the board to use CONFIG_SPI_FLASH before the v2019.07 release.
> +(net2big_v2) This board does not use CONFIG_DM_ETH (Driver Model
> +(net2big_v2) for Ethernet drivers). Please update the board to use
> +(net2big_v2) CONFIG_DM_ETH before the v2020.07 release. Failure to
> +(net2big_v2) update by the deadline may result in board removal.
> 
> So there's a lot of stuff that needs updating.  Conversion to CONFIG_DM
> is what you'll need to then convert SPI, ETH and USB to use DM and the
> IDE driver also needs attention and conversion.  Thanks!

Hi Tom,

I am working on it. But so far it is not going very well and the whole
thing is turning into a debug session.

But I'll do my best and whatever the result will be, I'll send you an
update by the end of the next week.

Is this acceptable to you ?

Thanks.

Simon
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200620/3129d168/attachment.sig>
Tom Rini June 20, 2020, 12:25 a.m. UTC | #4 
On Sat, Jun 20, 2020 at 02:24:47AM +0200, Simon Guinot wrote:
> On Thu, Jun 18, 2020 at 06:25:06PM -0400, Tom Rini wrote:
> > On Fri, Jun 19, 2020 at 12:02:17AM +0200, Simon Guinot wrote:
> > > On Thu, Jun 18, 2020 at 11:15:14PM +0530, Jagan Teki wrote:
> > > Hi Jagan,
> > > 
> > > > This board has not been converted to CONFIG_DM by the deadline.
> > > 
> > > Is that possible to negociate a new deadline ?
> > 
> > Well, when will you be able to spend some time bringing the platform up
> > to current standards?  Doing a quick build for net2big_v2 I see:
> > +(net2big_v2) ===================== WARNING ======================
> > +(net2big_v2) This board does not use CONFIG_DM. CONFIG_DM will be
> > +(net2big_v2) compulsory starting with the v2020.01 release.
> > +(net2big_v2) Failure to update may result in board removal.
> > +(net2big_v2) See doc/driver-model/migration.rst for more info.
> > +(net2big_v2) ====================================================
> > +(net2big_v2) This board does not use CONFIG_DM_USB. Please update
> > +(net2big_v2) the board to use CONFIG_DM_USB before the v2019.07 release.
> > +(net2big_v2) Failure to update by the deadline may result in board removal.
> > +(net2big_v2) This board does use CONFIG_MVSATA_IDE which is not
> > +(net2big_v2) ported to driver-model (DM) yet. Please update the storage
> > +(net2big_v2) controller driver to use CONFIG_AHCI before the v2019.07
> > +(net2big_v2) release.
> > +(net2big_v2) This board does not use CONFIG_DM_SPI_FLASH. Please update
> > +(net2big_v2) the board to use CONFIG_SPI_FLASH before the v2019.07 release.
> > +(net2big_v2) This board does not use CONFIG_DM_ETH (Driver Model
> > +(net2big_v2) for Ethernet drivers). Please update the board to use
> > +(net2big_v2) CONFIG_DM_ETH before the v2020.07 release. Failure to
> > +(net2big_v2) update by the deadline may result in board removal.
> > 
> > So there's a lot of stuff that needs updating.  Conversion to CONFIG_DM
> > is what you'll need to then convert SPI, ETH and USB to use DM and the
> > IDE driver also needs attention and conversion.  Thanks!
> 
> Hi Tom,
> 
> I am working on it. But so far it is not going very well and the whole
> thing is turning into a debug session.
> 
> But I'll do my best and whatever the result will be, I'll send you an
> update by the end of the next week.
> 
> Is this acceptable to you ?

Yes, thanks!
Simon Guinot June 24, 2020, 10:42 p.m. UTC | #5 
On Fri, Jun 19, 2020 at 08:25:59PM -0400, Tom Rini wrote:
> On Sat, Jun 20, 2020 at 02:24:47AM +0200, Simon Guinot wrote:
> > On Thu, Jun 18, 2020 at 06:25:06PM -0400, Tom Rini wrote:
> > > On Fri, Jun 19, 2020 at 12:02:17AM +0200, Simon Guinot wrote:
> > > > On Thu, Jun 18, 2020 at 11:15:14PM +0530, Jagan Teki wrote:
> > > > Hi Jagan,
> > > > 
> > > > > This board has not been converted to CONFIG_DM by the deadline.
> > > > 
> > > > Is that possible to negociate a new deadline ?
> > > 
> > > Well, when will you be able to spend some time bringing the platform up
> > > to current standards?  Doing a quick build for net2big_v2 I see:
> > > +(net2big_v2) ===================== WARNING ======================
> > > +(net2big_v2) This board does not use CONFIG_DM. CONFIG_DM will be
> > > +(net2big_v2) compulsory starting with the v2020.01 release.
> > > +(net2big_v2) Failure to update may result in board removal.
> > > +(net2big_v2) See doc/driver-model/migration.rst for more info.
> > > +(net2big_v2) ====================================================
> > > +(net2big_v2) This board does not use CONFIG_DM_USB. Please update
> > > +(net2big_v2) the board to use CONFIG_DM_USB before the v2019.07 release.
> > > +(net2big_v2) Failure to update by the deadline may result in board removal.
> > > +(net2big_v2) This board does use CONFIG_MVSATA_IDE which is not
> > > +(net2big_v2) ported to driver-model (DM) yet. Please update the storage
> > > +(net2big_v2) controller driver to use CONFIG_AHCI before the v2019.07
> > > +(net2big_v2) release.
> > > +(net2big_v2) This board does not use CONFIG_DM_SPI_FLASH. Please update
> > > +(net2big_v2) the board to use CONFIG_SPI_FLASH before the v2019.07 release.
> > > +(net2big_v2) This board does not use CONFIG_DM_ETH (Driver Model
> > > +(net2big_v2) for Ethernet drivers). Please update the board to use
> > > +(net2big_v2) CONFIG_DM_ETH before the v2020.07 release. Failure to
> > > +(net2big_v2) update by the deadline may result in board removal.
> > > 
> > > So there's a lot of stuff that needs updating.  Conversion to CONFIG_DM
> > > is what you'll need to then convert SPI, ETH and USB to use DM and the
> > > IDE driver also needs attention and conversion.  Thanks!
> > 
> > Hi Tom,
> > 
> > I am working on it. But so far it is not going very well and the whole
> > thing is turning into a debug session.
> > 
> > But I'll do my best and whatever the result will be, I'll send you an
> > update by the end of the next week.
> > 
> > Is this acceptable to you ?

Hi Tom,

I just sent a patch series converting the LaCie boards to use DM
drivers.

I apologize for missing all this DM deadlines.

Simon
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200625/04c34ae9/attachment.sig>
diff mbox series

Patch

diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index ae44cb665e..ad6aef45bf 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -35,9 +35,6 @@  config TARGET_KM_KIRKWOOD
 	bool "KM Kirkwood Board"
 	select VENDOR_KM
 
-config TARGET_NET2BIG_V2
-	bool "LaCie 2Big Network v2 NAS Board"
-
 config TARGET_NETSPACE_V2
 	bool "LaCie netspace_v2 Board"
 
@@ -80,7 +77,6 @@  source "board/cloudengines/pogo_e02/Kconfig"
 source "board/d-link/dns325/Kconfig"
 source "board/iomega/iconnect/Kconfig"
 source "board/keymile/Kconfig"
-source "board/LaCie/net2big_v2/Kconfig"
 source "board/LaCie/netspace_v2/Kconfig"
 source "board/raidsonic/ib62x0/Kconfig"
 source "board/Seagate/dockstar/Kconfig"
diff --git a/board/LaCie/net2big_v2/Kconfig b/board/LaCie/net2big_v2/Kconfig
deleted file mode 100644
index ba460dba45..0000000000
--- a/board/LaCie/net2big_v2/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@ 
-if TARGET_NET2BIG_V2
-
-config SYS_BOARD
-	default "net2big_v2"
-
-config SYS_VENDOR
-	default "LaCie"
-
-config SYS_CONFIG_NAME
-	default "lacie_kw"
-
-endif
diff --git a/board/LaCie/net2big_v2/MAINTAINERS b/board/LaCie/net2big_v2/MAINTAINERS
deleted file mode 100644
index 8fec70315f..0000000000
--- a/board/LaCie/net2big_v2/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@ 
-NET2BIG_V2 BOARD
-M:	Simon Guinot <simon.guinot at sequanux.org>
-S:	Maintained
-F:	board/LaCie/net2big_v2/
-F:	include/configs/lacie_kw.h
-F:	configs/d2net_v2_defconfig
-F:	configs/net2big_v2_defconfig
diff --git a/board/LaCie/net2big_v2/Makefile b/board/LaCie/net2big_v2/Makefile
deleted file mode 100644
index 3d12b72812..0000000000
--- a/board/LaCie/net2big_v2/Makefile
+++ /dev/null
@@ -1,13 +0,0 @@ 
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
-
-obj-y	:= net2big_v2.o ../common/common.o
-ifneq ($(and $(CONFIG_KIRKWOOD_GPIO),$(CONFIG_NET2BIG_V2)),)
-obj-y	+= ../common/cpld-gpio-bus.o
-endif
diff --git a/board/LaCie/net2big_v2/kwbimage.cfg b/board/LaCie/net2big_v2/kwbimage.cfg
deleted file mode 100644
index 3897a1197a..0000000000
--- a/board/LaCie/net2big_v2/kwbimage.cfg
+++ /dev/null
@@ -1,149 +0,0 @@ 
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM	spi	# Boot from SPI flash
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1B1B1B9B
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000C30	# DDR Configuration register
-# bit13-0:  0xa00 (2560 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x38743000	# DDR Controller Control Low
-# bit 4:    0=addr/cmd in smame cycle
-# bit 5:    0=clk is driven during self refresh, we don't care for APX
-# bit 6:    0=use recommended falling edge of clk for addr/cmd
-# bit14:    0=input buffer always powered up
-# bit18:    1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31:    0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x22125451	# DDR Timing (Low) (active cycles value +1)
-# bit7-4:   TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20:    TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000A32	#  DDR Timing (High)
-# bit6-0:   TRFC
-# bit8-7:   TR2R
-# bit10-9:  TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x0000CCCC	#  DDR Address Control
-# bit1-0:   01, Cs0width=x16
-# bit3-2:   11, Cs0size=1Gb
-# bit5-4:   00, Cs2width=nonexistent
-# bit7-6:   00, Cs1size =nonexistent
-# bit9-8:   00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16:    0,  Cs0AddrSel
-# bit17:    0,  Cs1AddrSel
-# bit18:    0,  Cs2AddrSel
-# bit19:    0,  Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
-# bit0:    0,  OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000	#  DDR Operation
-# bit3-0:   0x0, DDR cmd
-# bit31-4:  0 required
-
-DATA 0xFFD0141C 0x00000662	#  DDR Mode
-# bit2-0:   2, BurstLen=2 required
-# bit3:     0, BurstType=0 required
-# bit6-4:   4, CL=5
-# bit7:     0, TestMode=0 normal
-# bit8:     0, DLL reset=0 normal
-# bit11-9:  6, auto-precharge write recovery ????????????
-# bit12:    0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000044	#  DDR Extended Mode
-# bit0:    0,  DDR DLL enabled
-# bit1:    1,  DDR drive strenght reduced
-# bit2:    1,  DDR ODT control lsd enabled
-# bit5-3:  000, required
-# bit6:    1,  DDR ODT control msb, enabled
-# bit9-7:  000, required
-# bit10:   0,  differential DQS enabled
-# bit11:   0, required
-# bit12:   0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F17F	#  DDR Controller Control High
-# bit2-0:  111, required
-# bit3  :  1  , MBUS Burst Chop disabled
-# bit6-4:  111, required
-# bit7  :  1  , D2P Latency enabled
-# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9  :  0  , no half clock cycle addition to dataout
-# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0    required
-
-DATA 0xFFD01428 0x00096630	# DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00009663	# DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x0FFFFFF1	# CS[0]n Size
-# bit0:    1,  Window enabled
-# bit1:    0,  Write Protect disabled
-# bit3-2:  00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x07, Size (i.e. 128MB)
-
-DATA 0xFFD0150C 0x00000000	# CS[1]n Size, window disabled
-DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00010000	#  DDR ODT Control (Low)
-# bit3-0:  1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
-# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
-
-DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
-# bit1-0:  00, ODT0 controlled by ODT Control (low) register above
-# bit3-2:  01, ODT1 active NEVER!
-# bit31-4: zero, required
-
-DATA 0xFFD0149C 0x0000E40F	# CPU ODT Control
-# bit3-0:  1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
-# bit7-4:  1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
-# bit11-10:1, DQ_ODTSel. ODT select turned on
-
-DATA 0xFFD01480 0x00000001	# DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
diff --git a/board/LaCie/net2big_v2/net2big_v2.c b/board/LaCie/net2big_v2/net2big_v2.c
deleted file mode 100644
index dbd8b5755d..0000000000
--- a/board/LaCie/net2big_v2/net2big_v2.c
+++ /dev/null
@@ -1,257 +0,0 @@ 
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
- *
- * Based on Kirkwood support:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
- */
-
-#include <common.h>
-#include <command.h>
-#include <env.h>
-#include <i2c.h>
-#include <init.h>
-#include <net.h>
-#include <asm/mach-types.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include <asm/arch/gpio.h>
-
-#include "net2big_v2.h"
-#include "../common/common.h"
-#include "../common/cpld-gpio-bus.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-	/* GPIO configuration */
-	mvebu_config_gpio(NET2BIG_V2_OE_VAL_LOW, NET2BIG_V2_OE_VAL_HIGH,
-			  NET2BIG_V2_OE_LOW, NET2BIG_V2_OE_HIGH);
-
-	/* Multi-Purpose Pins Functionality configuration */
-	static const u32 kwmpp_config[] = {
-		MPP0_SPI_SCn,
-		MPP1_SPI_MOSI,
-		MPP2_SPI_SCK,
-		MPP3_SPI_MISO,
-		MPP6_SYSRST_OUTn,
-		MPP7_GPO,		/* Request power-off */
-		MPP8_TW_SDA,
-		MPP9_TW_SCK,
-		MPP10_UART0_TXD,
-		MPP11_UART0_RXD,
-		MPP13_GPIO,		/* Rear power switch (on|auto) */
-		MPP14_GPIO,		/* USB fuse alarm */
-		MPP15_GPIO,		/* Rear power switch (auto|off) */
-		MPP16_GPIO,		/* SATA HDD1 power */
-		MPP17_GPIO,		/* SATA HDD2 power */
-		MPP20_SATA1_ACTn,
-		MPP21_SATA0_ACTn,
-		MPP24_GPIO,		/* USB mode select */
-		MPP26_GPIO,		/* USB device vbus */
-		MPP28_GPIO,		/* USB enable host vbus */
-		MPP29_GPIO,		/* CPLD GPIO bus ALE */
-		MPP34_GPIO,		/* Rear Push button 0=on 1=off */
-		MPP35_GPIO,		/* Inhibit switch power-off */
-		MPP36_GPIO,		/* SATA HDD1 presence */
-		MPP37_GPIO,		/* SATA HDD2 presence */
-		MPP40_GPIO,		/* eSATA presence */
-		MPP44_GPIO,		/* CPLD GPIO bus (data 0) */
-		MPP45_GPIO,		/* CPLD GPIO bus (data 1) */
-		MPP46_GPIO,		/* CPLD GPIO bus (data 2) */
-		MPP47_GPIO,		/* CPLD GPIO bus (addr 0) */
-		MPP48_GPIO,		/* CPLD GPIO bus (addr 1) */
-		MPP49_GPIO,		/* CPLD GPIO bus (addr 2) */
-		0
-	};
-
-	kirkwood_mpp_conf(kwmpp_config, NULL);
-
-	return 0;
-}
-
-int board_init(void)
-{
-	/* Machine number */
-	gd->bd->bi_arch_number = MACH_TYPE_NET2BIG_V2;
-
-	/* Boot parameters address */
-	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
-
-	return 0;
-}
-
-#if defined(CONFIG_MISC_INIT_R)
-
-#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_G762_ADDR)
-/*
- * Start I2C fan (GMT G762 controller)
- */
-static void init_fan(void)
-{
-	u8 data;
-
-	i2c_set_bus_num(0);
-
-	/* Enable open-loop and PWM modes */
-	data = 0x20;
-	if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
-		      G762_REG_FAN_CMD1, 1, &data, 1) != 0)
-		goto err;
-	data = 0;
-	if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
-		      G762_REG_SET_CNT, 1, &data, 1) != 0)
-		goto err;
-	/*
-	 * RPM to PWM (set_out register) fan speed conversion array:
-	 * 0    0x00
-	 * 1500	0x04
-	 * 2800	0x08
-	 * 3400	0x0C
-	 * 3700	0x10
-	 * 4400	0x20
-	 * 4700	0x30
-	 * 4800	0x50
-	 * 5200	0x80
-	 * 5400	0xC0
-	 * 5500	0xFF
-	 *
-	 * Start fan at low speed (2800 RPM):
-	 */
-	data = 0x08;
-	if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
-		      G762_REG_SET_OUT, 1, &data, 1) != 0)
-		goto err;
-
-	return;
-err:
-	printf("Error: failed to start I2C fan @%02x\n",
-	       CONFIG_SYS_I2C_G762_ADDR);
-}
-#else
-static void init_fan(void) {}
-#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_G762_ADDR */
-
-#if defined(CONFIG_NET2BIG_V2) && defined(CONFIG_KIRKWOOD_GPIO)
-/*
- * CPLD GPIO bus:
- *
- * - address register : bit [0-2] -> GPIO [47-49]
- * - data register    : bit [0-2] -> GPIO [44-46]
- * - enable register  : GPIO 29
- */
-static unsigned cpld_gpio_bus_addr[] = { 47, 48, 49 };
-static unsigned cpld_gpio_bus_data[] = { 44, 45, 46 };
-
-static struct cpld_gpio_bus cpld_gpio_bus = {
-	.addr		= cpld_gpio_bus_addr,
-	.num_addr	= ARRAY_SIZE(cpld_gpio_bus_addr),
-	.data		= cpld_gpio_bus_data,
-	.num_data	= ARRAY_SIZE(cpld_gpio_bus_data),
-	.enable		= 29,
-};
-
-/*
- * LEDs configuration:
- *
- * The LEDs are controlled by a CPLD and can be configured through
- * the CPLD GPIO bus.
- *
- * Address register selection:
- *
- * addr | register
- * ----------------------------
- *   0  | front LED
- *   1  | front LED brightness
- *   2  | SATA LED brightness
- *   3  | SATA0 LED
- *   4  | SATA1 LED
- *   5  | SATA2 LED
- *   6  | SATA3 LED
- *   7  | SATA4 LED
- *
- * Data register configuration:
- *
- * data | LED brightness
- * -------------------------------------------------
- *   0  | min (off)
- *   -  | -
- *   7  | max
- *
- * data | front LED mode
- * -------------------------------------------------
- *   0  | fix off
- *   1  | fix blue on
- *   2  | fix red on
- *   3  | blink blue on=1 sec and blue off=1 sec
- *   4  | blink red on=1 sec and red off=1 sec
- *   5  | blink blue on=2.5 sec and red on=0.5 sec
- *   6  | blink blue on=1 sec and red on=1 sec
- *   7  | blink blue on=0.5 sec and blue off=2.5 sec
- *
- * data | SATA LED mode
- * -------------------------------------------------
- *   0  | fix off
- *   1  | SATA activity blink
- *   2  | fix red on
- *   3  | blink blue on=1 sec and blue off=1 sec
- *   4  | blink red on=1 sec and red off=1 sec
- *   5  | blink blue on=2.5 sec and red on=0.5 sec
- *   6  | blink blue on=1 sec and red on=1 sec
- *   7  | fix blue on
- */
-static void init_leds(void)
-{
-	/* Enable the front blue LED */
-	cpld_gpio_bus_write(&cpld_gpio_bus, 0, 1);
-	cpld_gpio_bus_write(&cpld_gpio_bus, 1, 3);
-
-	/* Configure SATA LEDs to blink in relation with the SATA activity */
-	cpld_gpio_bus_write(&cpld_gpio_bus, 3, 1);
-	cpld_gpio_bus_write(&cpld_gpio_bus, 4, 1);
-	cpld_gpio_bus_write(&cpld_gpio_bus, 2, 3);
-}
-#else
-static void init_leds(void) {}
-#endif /* CONFIG_NET2BIG_V2 && CONFIG_KIRKWOOD_GPIO */
-
-int misc_init_r(void)
-{
-	init_fan();
-#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
-	if (!env_get("ethaddr")) {
-		uchar mac[6];
-		if (lacie_read_mac_address(mac) == 0)
-			eth_env_set_enetaddr("ethaddr", mac);
-	}
-#endif
-	init_leds();
-
-	return 0;
-}
-#endif /* CONFIG_MISC_INIT_R */
-
-#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
-/* Configure and initialize PHY */
-void reset_phy(void)
-{
-	mv_phy_88e1116_init("egiga0", 8);
-}
-#endif
-
-#if defined(CONFIG_KIRKWOOD_GPIO)
-/* Return GPIO push button status */
-static int
-do_read_push_button(struct cmd_tbl *cmdtp, int flag, int argc,
-		    char *const argv[])
-{
-	return !kw_gpio_get_value(NET2BIG_V2_GPIO_PUSH_BUTTON);
-}
-
-U_BOOT_CMD(button, 1, 1, do_read_push_button,
-	   "Return GPIO push button status 0=off 1=on", "");
-#endif
diff --git a/board/LaCie/net2big_v2/net2big_v2.h b/board/LaCie/net2big_v2/net2big_v2.h
deleted file mode 100644
index d61dd0e998..0000000000
--- a/board/LaCie/net2big_v2/net2big_v2.h
+++ /dev/null
@@ -1,28 +0,0 @@ 
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
- *
- * Based on Kirkwood support:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
- */
-
-#ifndef NET2BIG_V2_H
-#define NET2BIG_V2_H
-
-/* GPIO configuration */
-#define NET2BIG_V2_OE_LOW		0x0600E000
-#define NET2BIG_V2_OE_HIGH		0x00000134
-#define NET2BIG_V2_OE_VAL_LOW		0x10030000
-#define NET2BIG_V2_OE_VAL_HIGH		0x00000000
-
-/* Buttons */
-#define NET2BIG_V2_GPIO_PUSH_BUTTON	34
-
-/* GMT G762 registers (I2C fan controller) */
-#define G762_REG_SET_CNT		0x00
-#define G762_REG_SET_OUT		0x03
-#define G762_REG_FAN_CMD1		0x04
-
-#endif /* NET2BIG_V2_H */
diff --git a/configs/d2net_v2_defconfig b/configs/d2net_v2_defconfig
deleted file mode 100644
index fe3c6c4762..0000000000
--- a/configs/d2net_v2_defconfig
+++ /dev/null
@@ -1,53 +0,0 @@ 
-CONFIG_ARM=y
-CONFIG_SYS_DCACHE_OFF=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_TARGET_NET2BIG_V2=y
-CONFIG_ENV_SIZE=0x1000
-CONFIG_ENV_OFFSET=0x70000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_IDENT_STRING=" D2 v2"
-CONFIG_SYS_EXTRA_OPTIONS="D2NET_V2"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200"
-CONFIG_USE_PREBOOT=y
-CONFIG_CONSOLE_MUX=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="d2v2> "
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_IDE=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ISO_PARTITION=y
-CONFIG_EFI_PARTITION=y
-# CONFIG_PARTITION_UUIDS is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="kirkwood-d2net"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=20000000
-CONFIG_ENV_ADDR=0x70000
-CONFIG_MVSATA_IDE=y
-# CONFIG_MMC is not set
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_KIRKWOOD_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
diff --git a/configs/net2big_v2_defconfig b/configs/net2big_v2_defconfig
deleted file mode 100644
index 1389d30900..0000000000
--- a/configs/net2big_v2_defconfig
+++ /dev/null
@@ -1,53 +0,0 @@ 
-CONFIG_ARM=y
-CONFIG_SYS_DCACHE_OFF=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_TARGET_NET2BIG_V2=y
-CONFIG_ENV_SIZE=0x1000
-CONFIG_ENV_OFFSET=0x70000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_IDENT_STRING=" 2Big v2"
-CONFIG_SYS_EXTRA_OPTIONS="NET2BIG_V2"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200"
-CONFIG_USE_PREBOOT=y
-CONFIG_CONSOLE_MUX=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="2big2> "
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_IDE=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ISO_PARTITION=y
-CONFIG_EFI_PARTITION=y
-# CONFIG_PARTITION_UUIDS is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="kirkwood-net2big"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=20000000
-CONFIG_ENV_ADDR=0x70000
-CONFIG_MVSATA_IDE=y
-# CONFIG_MMC is not set
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_KIRKWOOD_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
diff --git a/include/configs/lacie_kw.h b/include/configs/lacie_kw.h
deleted file mode 100644
index 5bb0255a74..0000000000
--- a/include/configs/lacie_kw.h
+++ /dev/null
@@ -1,152 +0,0 @@ 
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
- */
-
-#ifndef _CONFIG_LACIE_KW_H
-#define _CONFIG_LACIE_KW_H
-
-/*
- * Machine number definition
- */
-#if defined(CONFIG_INETSPACE_V2)
-#define CONFIG_MACH_TYPE		MACH_TYPE_INETSPACE_V2
-#elif defined(CONFIG_NETSPACE_V2)
-#define CONFIG_MACH_TYPE		MACH_TYPE_NETSPACE_V2
-#elif defined(CONFIG_NETSPACE_LITE_V2)
-#define CONFIG_MACH_TYPE		MACH_TYPE_NETSPACE_LITE_V2
-#elif defined(CONFIG_NETSPACE_MINI_V2)
-#define CONFIG_MACH_TYPE		MACH_TYPE_NETSPACE_MINI_V2
-#elif defined(CONFIG_NETSPACE_MAX_V2)
-#define CONFIG_MACH_TYPE		MACH_TYPE_NETSPACE_MAX_V2
-#elif defined(CONFIG_D2NET_V2)
-#define CONFIG_MACH_TYPE		MACH_TYPE_D2NET_V2
-#elif defined(CONFIG_NET2BIG_V2)
-#define CONFIG_MACH_TYPE		MACH_TYPE_NET2BIG_V2
-#else
-#error "Unknown board"
-#endif
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_FEROCEON_88FR131		/* CPU Core subversion */
-/* SoC name */
-#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
-#define CONFIG_KW88F6192
-#else
-#define CONFIG_KW88F6281
-#endif
-#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
-
-/*
- * Core clock definition
- */
-#define CONFIG_SYS_TCLK			166000000 /* 166MHz */
-
-/*
- * SDRAM configuration
- */
-
-/*
- * Different SDRAM configuration and size for some of the boards derived
- * from the Network Space v2
- */
-#if defined(CONFIG_INETSPACE_V2)
-#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-is2.cfg
-#elif defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
-#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-ns2l.cfg
-#endif
-
-/*
- * mv-common.h should be defined after CMD configs since it used them
- * to enable certain macros
- */
-#include "mv-common.h"
-
-/* Remove or override few declarations from mv-common.h */
-#undef CONFIG_SYS_IDE_MAXBUS
-#undef CONFIG_SYS_IDE_MAXDEVICE
-
-/*
- * Enable platform initialisation via misc_init_r() function
- */
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS		{1, 0} /* enable port 0 only */
-#define CONFIG_NETCONSOLE
-#endif
-
-/*
- * SATA Driver configuration
- */
-#ifdef CONFIG_MVSATA_IDE
-#define CONFIG_SYS_ATA_IDE0_OFFSET      MV_SATA_PORT0_OFFSET
-#if defined(CONFIG_NETSPACE_MAX_V2) || defined(CONFIG_D2NET_V2) || \
-	defined(CONFIG_NET2BIG_V2)
-#define CONFIG_SYS_ATA_IDE1_OFFSET      MV_SATA_PORT1_OFFSET
-#define CONFIG_SYS_IDE_MAXBUS           2
-#define CONFIG_SYS_IDE_MAXDEVICE        2
-#else
-#define CONFIG_SYS_IDE_MAXBUS           1
-#define CONFIG_SYS_IDE_MAXDEVICE        1
-#endif
-#endif /* CONFIG_MVSATA_IDE */
-
-/*
- * Enable GPI0 support
- */
-#define CONFIG_KIRKWOOD_GPIO
-
-/*
- * Enable I2C support
- */
-#ifdef CONFIG_CMD_I2C
-/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4 /* 16-byte page size */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1 /* 8-bit device address */
-#if defined(CONFIG_NET2BIG_V2)
-#define CONFIG_SYS_I2C_G762_ADDR		0x3e
-#endif
-#endif /* CONFIG_CMD_I2C */
-
-/*
- * Partition support
- */
-
-/*
- * File systems support
- */
-
-/*
- * Environment variables configurations
- */
-
-/*
- * Default environment variables
- */
-#define CONFIG_BOOTCOMMAND					\
-	"dhcp && run netconsole; "				\
-	"if run usbload || run diskload; then bootm; fi"
-
-#define CONFIG_EXTRA_ENV_SETTINGS				\
-	"stdin=serial\0"					\
-	"stdout=serial\0"					\
-	"stderr=serial\0"					\
-	"bootfile=uImage\0"					\
-	"loadaddr=0x800000\0"					\
-	"autoload=no\0"						\
-	"netconsole="						\
-		"set stdin $stdin,nc; "				\
-		"set stdout $stdout,nc; "			\
-		"set stderr $stderr,nc;\0"			\
-	"diskload=ide reset && "				\
-		"ext2load ide 0:1 $loadaddr /boot/$bootfile\0"	\
-	"usbload=usb start && "					\
-		"fatload usb 0:1 $loadaddr /boot/$bootfile\0"
-
-#endif /* _CONFIG_LACIE_KW_H */