diff mbox

ARM: ux500: drop a chunk of GPIO definitions

Message ID 1392119819-1772-1-git-send-email-linus.walleij@linaro.org
State Accepted
Commit 8cc0071556c18bf3dc036a33fa989d0ebe537e33
Headers show

Commit Message

Linus Walleij Feb. 11, 2014, 11:56 a.m. UTC
The Ux500 GPIOs are now assigned dynamically from the device tree.
Drop this table of static assignments.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/mach-ux500/board-mop500.h | 69 --------------------------------------
 1 file changed, 69 deletions(-)
diff mbox

Patch

diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h
index bb408b8f48de..32cc0d8d8a0e 100644
--- a/arch/arm/mach-ux500/board-mop500.h
+++ b/arch/arm/mach-ux500/board-mop500.h
@@ -7,78 +7,9 @@ 
 #ifndef __BOARD_MOP500_H
 #define __BOARD_MOP500_H
 
-/* For NOMADIK_NR_GPIO */
-#include "irqs.h"
 #include <linux/platform_data/asoc-ux500-msp.h>
 #include <linux/amba/mmci.h>
 
-/* Snowball specific GPIO assignments, this board has no GPIO expander */
-#define SNOWBALL_ACCEL_INT1_GPIO	163
-#define SNOWBALL_ACCEL_INT2_GPIO	164
-#define SNOWBALL_MAGNET_DRDY_GPIO	165
-#define SNOWBALL_SDMMC_EN_GPIO		217
-#define SNOWBALL_SDMMC_1V8_3V_GPIO	228
-#define SNOWBALL_SDMMC_CD_GPIO		218
-
-/* HREFv60-specific GPIO assignments, this board has no GPIO expander */
-#define HREFV60_SDMMC_1V8_3V_GPIO	5
-#define HREFV60_CAMERA_FLASH_ENABLE	21
-#define HREFV60_MAGNET_DRDY_GPIO	32
-#define HREFV60_DISP1_RST_GPIO		65
-#define HREFV60_DISP2_RST_GPIO		66
-#define HREFV60_ACCEL_INT1_GPIO		82
-#define HREFV60_ACCEL_INT2_GPIO		83
-#define HREFV60_SDMMC_CD_GPIO		95
-#define HREFV60_XSHUTDOWN_SECONDARY_SENSOR 140
-#define HREFV60_TOUCH_RST_GPIO		143
-#define HREFV60_HAL_SW_GPIO		145
-#define HREFV60_SDMMC_EN_GPIO		169
-#define HREFV60_MMIO_XENON_CHARGE	170
-#define HREFV60_PROX_SENSE_GPIO		217
-
-/* MOP500 generic GPIOs */
-#define CAMERA_FLASH_INT_PIN		7
-#define CYPRESS_TOUCH_INT_PIN		84
-#define XSHUTDOWN_PRIMARY_SENSOR	141
-#define XSHUTDOWN_SECONDARY_SENSOR	142
-#define CYPRESS_TOUCH_RST_GPIO		143
-#define MOP500_HDMI_RST_GPIO		196
-#define CYPRESS_SLAVE_SELECT_GPIO	216
-
-/* GPIOs on the TC35892 expander */
-#define MOP500_EGPIO(x)			(NOMADIK_NR_GPIO + (x))
-#define GPIO_MAGNET_DRDY		MOP500_EGPIO(1)
-#define GPIO_SDMMC_CD			MOP500_EGPIO(3)
-#define GPIO_CAMERA_FLASH_ENABLE	MOP500_EGPIO(4)
-#define GPIO_MMIO_XENON_CHARGE		MOP500_EGPIO(5)
-#define GPIO_PROX_SENSOR		MOP500_EGPIO(7)
-#define GPIO_HAL_SENSOR			MOP500_EGPIO(8)
-#define GPIO_ACCEL_INT1			MOP500_EGPIO(10)
-#define GPIO_ACCEL_INT2			MOP500_EGPIO(11)
-#define GPIO_BU21013_CS			MOP500_EGPIO(13)
-#define MOP500_DISP2_RST_GPIO		MOP500_EGPIO(14)
-#define MOP500_DISP1_RST_GPIO		MOP500_EGPIO(15)
-#define GPIO_SDMMC_EN			MOP500_EGPIO(17)
-#define GPIO_SDMMC_1V8_3V_SEL		MOP500_EGPIO(18)
-#define MOP500_EGPIO_END		MOP500_EGPIO(24)
-
-/*
- * GPIOs on the AB8500 mixed-signals circuit
- * Notice that we subtract 1 from the number passed into the macro, this is
- * because the AB8500 GPIO pins are enumbered starting from 1, so the value in
- * parens matches the GPIO pin number in the data sheet.
- */
-#define MOP500_AB8500_PIN_GPIO(x)	(MOP500_EGPIO_END + (x) - 1)
-/*Snowball AB8500 GPIO */
-#define SNOWBALL_VSMPS2_1V8_GPIO	MOP500_AB8500_PIN_GPIO(1)	/* SYSCLKREQ2/GPIO1 */
-#define SNOWBALL_PM_GPIO1_GPIO		MOP500_AB8500_PIN_GPIO(2)	/* SYSCLKREQ3/GPIO2 */
-#define SNOWBALL_WLAN_CLK_REQ_GPIO	MOP500_AB8500_PIN_GPIO(3)	/* SYSCLKREQ4/GPIO3 */
-#define SNOWBALL_PM_GPIO4_GPIO		MOP500_AB8500_PIN_GPIO(4)	/* SYSCLKREQ6/GPIO4 */
-#define SNOWBALL_EN_3V6_GPIO		MOP500_AB8500_PIN_GPIO(16)	/* PWMOUT3/GPIO16 */
-#define SNOWBALL_PME_ETH_GPIO		MOP500_AB8500_PIN_GPIO(24)	/* SYSCLKREQ7/GPIO24 */
-#define SNOWBALL_EN_3V3_ETH_GPIO	MOP500_AB8500_PIN_GPIO(26)	/* GPIO26 */
-
-struct device;
 extern struct mmci_platform_data mop500_sdi0_data;
 extern struct mmci_platform_data mop500_sdi1_data;
 extern struct mmci_platform_data mop500_sdi2_data;