[2/3] spi: atmel: Remove nondm code

diff --git a/drivers/spi/atmel_spi.c b/drivers/spi/atmel_spi.c
index f076e92a93..b9f684d67e 100644
--- a/drivers/spi/atmel_spi.c
+++ b/drivers/spi/atmel_spi.c
@@ -14,210 +14,13 @@ 
 
 #include <asm/arch/clk.h>
 #include <asm/arch/hardware.h>
-#ifdef CONFIG_DM_SPI
 #include <asm/arch/at91_spi.h>
-#endif
 #if CONFIG_IS_ENABLED(DM_GPIO)
 #include <asm/gpio.h>
 #endif
 
 #include "atmel_spi.h"
 
-#ifndef CONFIG_DM_SPI
-
-static int spi_has_wdrbt(struct atmel_spi_slave *slave)
-{
-	unsigned int ver;
-
-	ver = spi_readl(slave, VERSION);
-
-	return (ATMEL_SPI_VERSION_REV(ver) >= 0x210);
-}
-
-struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
-			unsigned int max_hz, unsigned int mode)
-{
-	struct atmel_spi_slave	*as;
-	unsigned int		scbr;
-	u32			csrx;
-	void			*regs;
-
-	if (!spi_cs_is_valid(bus, cs))
-		return NULL;
-
-	switch (bus) {
-	case 0:
-		regs = (void *)ATMEL_BASE_SPI0;
-		break;
-#ifdef ATMEL_BASE_SPI1
-	case 1:
-		regs = (void *)ATMEL_BASE_SPI1;
-		break;
-#endif
-#ifdef ATMEL_BASE_SPI2
-	case 2:
-		regs = (void *)ATMEL_BASE_SPI2;
-		break;
-#endif
-#ifdef ATMEL_BASE_SPI3
-	case 3:
-		regs = (void *)ATMEL_BASE_SPI3;
-		break;
-#endif
-	default:
-		return NULL;
-	}
-
-
-	scbr = (get_spi_clk_rate(bus) + max_hz - 1) / max_hz;
-	if (scbr > ATMEL_SPI_CSRx_SCBR_MAX)
-		/* Too low max SCK rate */
-		return NULL;
-	if (scbr < 1)
-		scbr = 1;
-
-	csrx = ATMEL_SPI_CSRx_SCBR(scbr);
-	csrx |= ATMEL_SPI_CSRx_BITS(ATMEL_SPI_BITS_8);
-	if (!(mode & SPI_CPHA))
-		csrx |= ATMEL_SPI_CSRx_NCPHA;
-	if (mode & SPI_CPOL)
-		csrx |= ATMEL_SPI_CSRx_CPOL;
-
-	as = spi_alloc_slave(struct atmel_spi_slave, bus, cs);
-	if (!as)
-		return NULL;
-
-	as->regs = regs;
-	as->mr = ATMEL_SPI_MR_MSTR | ATMEL_SPI_MR_MODFDIS
-			| ATMEL_SPI_MR_PCS(~(1 << cs) & 0xf);
-	if (spi_has_wdrbt(as))
-		as->mr |= ATMEL_SPI_MR_WDRBT;
-
-	spi_writel(as, CSR(cs), csrx);
-
-	return &as->slave;
-}
-
-void spi_free_slave(struct spi_slave *slave)
-{
-	struct atmel_spi_slave *as = to_atmel_spi(slave);
-
-	free(as);
-}
-
-int spi_claim_bus(struct spi_slave *slave)
-{
-	struct atmel_spi_slave *as = to_atmel_spi(slave);
-
-	/* Enable the SPI hardware */
-	spi_writel(as, CR, ATMEL_SPI_CR_SPIEN);
-
-	/*
-	 * Select the slave. This should set SCK to the correct
-	 * initial state, etc.
-	 */
-	spi_writel(as, MR, as->mr);
-
-	return 0;
-}
-
-void spi_release_bus(struct spi_slave *slave)
-{
-	struct atmel_spi_slave *as = to_atmel_spi(slave);
-
-	/* Disable the SPI hardware */
-	spi_writel(as, CR, ATMEL_SPI_CR_SPIDIS);
-}
-
-int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
-		const void *dout, void *din, unsigned long flags)
-{
-	struct atmel_spi_slave *as = to_atmel_spi(slave);
-	unsigned int	len_tx;
-	unsigned int	len_rx;
-	unsigned int	len;
-	u32		status;
-	const u8	*txp = dout;
-	u8		*rxp = din;
-	u8		value;
-
-	if (bitlen == 0)
-		/* Finish any previously submitted transfers */
-		goto out;
-
-	/*
-	 * TODO: The controller can do non-multiple-of-8 bit
-	 * transfers, but this driver currently doesn't support it.
-	 *
-	 * It's also not clear how such transfers are supposed to be
-	 * represented as a stream of bytes...this is a limitation of
-	 * the current SPI interface.
-	 */
-	if (bitlen % 8) {
-		/* Errors always terminate an ongoing transfer */
-		flags |= SPI_XFER_END;
-		goto out;
-	}
-
-	len = bitlen / 8;
-
-	/*
-	 * The controller can do automatic CS control, but it is
-	 * somewhat quirky, and it doesn't really buy us much anyway
-	 * in the context of U-Boot.
-	 */
-	if (flags & SPI_XFER_BEGIN) {
-		spi_cs_activate(slave);
-		/*
-		 * sometimes the RDR is not empty when we get here,
-		 * in theory that should not happen, but it DOES happen.
-		 * Read it here to be on the safe side.
-		 * That also clears the OVRES flag. Required if the
-		 * following loop exits due to OVRES!
-		 */
-		spi_readl(as, RDR);
-	}
-
-	for (len_tx = 0, len_rx = 0; len_rx < len; ) {
-		status = spi_readl(as, SR);
-
-		if (status & ATMEL_SPI_SR_OVRES)
-			return -1;
-
-		if (len_tx < len && (status & ATMEL_SPI_SR_TDRE)) {
-			if (txp)
-				value = *txp++;
-			else
-				value = 0;
-			spi_writel(as, TDR, value);
-			len_tx++;
-		}
-		if (status & ATMEL_SPI_SR_RDRF) {
-			value = spi_readl(as, RDR);
-			if (rxp)
-				*rxp++ = value;
-			len_rx++;
-		}
-	}
-
-out:
-	if (flags & SPI_XFER_END) {
-		/*
-		 * Wait until the transfer is completely done before
-		 * we deactivate CS.
-		 */
-		do {
-			status = spi_readl(as, SR);
-		} while (!(status & ATMEL_SPI_SR_TXEMPTY));
-
-		spi_cs_deactivate(slave);
-	}
-
-	return 0;
-}
-
-#else
-
 #define MAX_CS_COUNT	4
 
 struct atmel_spi_platdata {
@@ -507,4 +310,3 @@  U_BOOT_DRIVER(atmel_spi) = {
 	.priv_auto_alloc_size = sizeof(struct atmel_spi_priv),
 	.probe	= atmel_spi_probe,
 };
-#endif
diff --git a/drivers/spi/atmel_spi.h b/drivers/spi/atmel_spi.h
index b602887c29..9663cca5e6 100644
--- a/drivers/spi/atmel_spi.h
+++ b/drivers/spi/atmel_spi.h
@@ -79,17 +79,6 @@ 
 #define ATMEL_SPI_BITS_15		7
 #define ATMEL_SPI_BITS_16		8
 
-struct atmel_spi_slave {
-	struct spi_slave slave;
-	void		*regs;
-	u32		mr;
-};
-
-static inline struct atmel_spi_slave *to_atmel_spi(struct spi_slave *slave)
-{
-	return container_of(slave, struct atmel_spi_slave, slave);
-}
-
 /* Register access macros */
 #define spi_readl(as, reg)					\
 	readl(as->regs + ATMEL_SPI_##reg)