diff mbox series

[v3,1/2] Bluetooth: btusb: define HCI packet sizes of USB Alts

Message ID 20200910140342.v3.1.I56de28ec171134cb9f97062e2c304a72822ca38b@changeid
State New
Headers show
Series To support the HFP WBS, a chip vendor may choose a particular | expand

Commit Message

Joseph Hwang Sept. 10, 2020, 6:04 a.m. UTC
It is desirable to define the HCI packet payload sizes of
USB alternate settings so that they can be exposed to user
space.

Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
---

Changes in v3:
- Set hdev->sco_mtu to rp->sco_mtu if the latter is smaller.

Changes in v2:
- Used sco_mtu instead of a new sco_pkt_len member in hdev.
- Do not overwrite hdev->sco_mtu in hci_cc_read_buffer_size
  if it has been set in the USB interface.

 drivers/bluetooth/btusb.c | 45 +++++++++++++++++++++++++++++----------
 net/bluetooth/hci_event.c | 14 +++++++++++-
 2 files changed, 47 insertions(+), 12 deletions(-)
diff mbox series

Patch

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index fe80588c7bd3a8..651d5731a6c6cf 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -459,6 +459,24 @@  static const struct dmi_system_id btusb_needs_reset_resume_table[] = {
 #define BTUSB_WAKEUP_DISABLE	14
 #define BTUSB_USE_ALT1_FOR_WBS	15
 
+/* Per core spec 5, vol 4, part B, table 2.1,
+ * list the hci packet payload sizes for various ALT settings.
+ * This is used to set the packet length for the wideband speech.
+ * If a controller does not probe its usb alt setting, the default
+ * value will be 0. Any clients at upper layers should interpret it
+ * as a default value and set a proper packet length accordingly.
+ *
+ * To calculate the HCI packet payload length:
+ *   for alternate settings 1 - 5:
+ *     hci_packet_size = suggested_max_packet_size * 3 (packets) -
+ *                       3 (HCI header octets)
+ *   for alternate setting 6:
+ *     hci_packet_size = suggested_max_packet_size - 3 (HCI header octets)
+ *   where suggested_max_packet_size is {9, 17, 25, 33, 49, 63}
+ *   for alt settings 1 - 6.
+ */
+static const int hci_packet_size_usb_alt[] = { 0, 24, 48, 72, 96, 144, 60 };
+
 struct btusb_data {
 	struct hci_dev       *hdev;
 	struct usb_device    *udev;
@@ -3959,6 +3977,15 @@  static int btusb_probe(struct usb_interface *intf,
 	hdev->notify = btusb_notify;
 	hdev->prevent_wake = btusb_prevent_wake;
 
+	if (id->driver_info & BTUSB_AMP) {
+		/* AMP controllers do not support SCO packets */
+		data->isoc = NULL;
+	} else {
+		/* Interface orders are hardcoded in the specification */
+		data->isoc = usb_ifnum_to_if(data->udev, ifnum_base + 1);
+		data->isoc_ifnum = ifnum_base + 1;
+	}
+
 #ifdef CONFIG_PM
 	err = btusb_config_oob_wake(hdev);
 	if (err)
@@ -4022,6 +4049,10 @@  static int btusb_probe(struct usb_interface *intf,
 		hdev->set_diag = btintel_set_diag;
 		hdev->set_bdaddr = btintel_set_bdaddr;
 		hdev->cmd_timeout = btusb_intel_cmd_timeout;
+
+		if (btusb_find_altsetting(data, 6))
+			hdev->sco_mtu = hci_packet_size_usb_alt[6];
+
 		set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
 		set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
 		set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
@@ -4063,15 +4094,6 @@  static int btusb_probe(struct usb_interface *intf,
 		btusb_check_needs_reset_resume(intf);
 	}
 
-	if (id->driver_info & BTUSB_AMP) {
-		/* AMP controllers do not support SCO packets */
-		data->isoc = NULL;
-	} else {
-		/* Interface orders are hardcoded in the specification */
-		data->isoc = usb_ifnum_to_if(data->udev, ifnum_base + 1);
-		data->isoc_ifnum = ifnum_base + 1;
-	}
-
 	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_RTL) &&
 	    (id->driver_info & BTUSB_REALTEK)) {
 		hdev->setup = btrtl_setup_realtek;
@@ -4083,9 +4105,10 @@  static int btusb_probe(struct usb_interface *intf,
 		 * (DEVICE_REMOTE_WAKEUP)
 		 */
 		set_bit(BTUSB_WAKEUP_DISABLE, &data->flags);
-		if (btusb_find_altsetting(data, 1))
+		if (btusb_find_altsetting(data, 1)) {
 			set_bit(BTUSB_USE_ALT1_FOR_WBS, &data->flags);
-		else
+			hdev->sco_mtu = hci_packet_size_usb_alt[1];
+		} else
 			bt_dev_err(hdev, "Device does not support ALT setting 1");
 	}
 
diff --git a/net/bluetooth/hci_event.c b/net/bluetooth/hci_event.c
index 33d8458fdd4adc..1869dc7ebbb5ac 100644
--- a/net/bluetooth/hci_event.c
+++ b/net/bluetooth/hci_event.c
@@ -730,7 +730,19 @@  static void hci_cc_read_buffer_size(struct hci_dev *hdev, struct sk_buff *skb)
 		return;
 
 	hdev->acl_mtu  = __le16_to_cpu(rp->acl_mtu);
-	hdev->sco_mtu  = rp->sco_mtu;
+	/* If the host controller interface is USB, the hdev->sco_mtu is
+	 * set in btusb.c and is not expected to be larger than the max sco
+	 * buffer size returned from the controller in rp->sco_mtu.
+	 */
+	if (hdev->sco_mtu > 0) {
+		if (rp->sco_mtu < hdev->sco_mtu) {
+			BT_ERR("sco mtu %d changed to max sco buffer size %d",
+			       hdev->sco_mtu, rp->sco_mtu);
+			hdev->sco_mtu = rp->sco_mtu;
+		}
+	} else {
+		hdev->sco_mtu  = rp->sco_mtu;
+	}
 	hdev->acl_pkts = __le16_to_cpu(rp->acl_max_pkt);
 	hdev->sco_pkts = __le16_to_cpu(rp->sco_max_pkt);