new file mode 100644
@@ -0,0 +1,123 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rohm,bd9576-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD9576MUF and BD9573MUF Power Management Integrated Circuit bindings
+
+maintainers:
+ - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description: |
+ BD9576MUF and BD9573MUF are power management ICs primarily intended for
+ powering the R-Car series processors.
+ The IC provides 6 power outputs with configurable sequencing and safety
+ monitoring. A watchdog logic with slow ping/windowed modes is also included.
+
+properties:
+ compatible:
+ enum:
+ - rohm,bd9576
+ - rohm,bd9573
+
+ reg:
+ description:
+ I2C slave address.
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ rohm,vout1-en-low:
+ description:
+ BD9576 and BD9573 VOUT1 regulator enable state can be individually
+ controlled by a GPIO. This is dictated by state of vout1-en pin during
+ the PMIC startup. If vout1-en is LOW during PMIC startup then the VOUT1
+ enable sate is controlled via this pin. Set this property if vout1-en
+ is wired to be down at PMIC start-up.
+ type: boolean
+
+ rohm,vout1-en-gpios:
+ description:
+ GPIO specifier to specify the GPIO connected to vout1-en for vout1 ON/OFF
+ state control.
+ maxItems: 1
+
+ rohm,ddr-sel-low:
+ description:
+ The BD9576 and BD9573 output voltage for DDR can be selected by setting
+ the ddr-sel pin low or high. Set this property if ddr-sel is grounded.
+ type: boolean
+
+ rohm,watchdog-enable-gpios:
+ description: The GPIO line used to enable the watchdog.
+ maxItems: 1
+
+ rohm,watchdog-ping-gpios:
+ description: The GPIO line used to ping the watchdog.
+ maxItems: 1
+
+ rohm,hw-timeout-ms:
+ maxItems: 2
+ description:
+ Watchog timeout in milliseconds. If single value is given it is
+ the maximum timeout. Eg. if pinging watchdog is not done within this time
+ limit the watchdog will be triggered. If two values are given watchdog
+ is configured in "window mode". Then first value is limit for short-ping
+ Eg. if watchdog is pinged sooner than that the watchdog will trigger.
+ When two values is given the second value is the maximum timeout.
+ # (HW) minimum for short timeout is 2ms, maximum 220 ms.
+ # (HW) minimum for max timeout is 4ms, maximum maximum 4416 ms.
+
+ regulators:
+ $ref: ../regulator/rohm,bd9576-regulator.yaml
+ description:
+ List of child nodes that specify the regulators.
+
+required:
+ - compatible
+ - reg
+ - regulators
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/leds/common.h>
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pmic: pmic@30 {
+ compatible = "rohm,bd9576";
+ reg = <0x30>;
+ rohm,vout1-en-low;
+ rohm,vout1-en-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+ rohm,ddr-sel-low;
+ rohm,watchdog-enable-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+ rohm,watchdog-ping-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
+ rohm,hw-timeout-ms = <150>, <2300>;
+
+ regulators {
+ boost1: regulator-vd50 {
+ regulator-name = "VD50";
+ };
+ buck1: regulator-vd18 {
+ regulator-name = "VD18";
+ };
+ buck2: regulator-vdddr {
+ regulator-name = "VDDDR";
+ };
+ buck3: regulator-vd10 {
+ regulator-name = "VD10";
+ };
+ ldo: regulator-voutl1 {
+ regulator-name = "VOUTL1";
+ };
+ sw: regulator-vouts1 {
+ regulator-name = "VOUTS1";
+ };
+ };
+ };
+ };
Add bindings for ROHM BD9576MUF and BD9573MUF PMICs. These PMICs are primarily intended to be used to power the R-Car series processors. They provide 6 power outputs, safety features and a watchdog with two functional modes. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> --- Changes from v2: - Replace bindings hw_margin_ms and rohm,hw-margin-min-ms with rohm,hw-timeout-ms .../bindings/mfd/rohm,bd9576-pmic.yaml | 123 ++++++++++++++++++ 1 file changed, 123 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd9576-pmic.yaml