@@ -92,6 +92,12 @@ config MVPP2
This driver supports the network interface units in the
Marvell ARMADA 375, 7K and 8K SoCs.
+config MVPP2_PTP
+ bool "Marvell Armada 8K Enable PTP support"
+ depends on NETWORK_PHY_TIMESTAMPING
+ depends on (PTP_1588_CLOCK = y && MVPP2 = y) || \
+ (PTP_1588_CLOCK && MVPP2 = m)
+
config PXA168_ETH
tristate "Marvell pxa168 ethernet support"
depends on HAS_IOMEM
@@ -4,4 +4,5 @@
#
obj-$(CONFIG_MVPP2) := mvpp2.o
-mvpp2-objs := mvpp2_main.o mvpp2_prs.o mvpp2_cls.o mvpp2_debugfs.o
+mvpp2-y := mvpp2_main.o mvpp2_prs.o mvpp2_cls.o mvpp2_debugfs.o
+mvpp2-$(CONFIG_MVPP2_PTP) += mvpp2_tai.o
@@ -505,6 +505,70 @@
#define MVPP22_SMI_MISC_CFG_REG 0x1204
#define MVPP22_SMI_POLLING_EN BIT(10)
+/* TAI registers, PPv2.2 only, relative to priv->iface_base */
+#define MVPP22_TAI_INT_CAUSE 0x1400
+#define MVPP22_TAI_INT_MASK 0x1404
+#define MVPP22_TAI_CR0 0x1408
+#define MVPP22_TAI_CR1 0x140c
+#define MVPP22_TAI_TCFCR0 0x1410
+#define MVPP22_TAI_TCFCR1 0x1414
+#define MVPP22_TAI_TCFCR2 0x1418
+#define MVPP22_TAI_FATWR 0x141c
+#define MVPP22_TAI_TOD_STEP_NANO_CR 0x1420
+#define MVPP22_TAI_TOD_STEP_FRAC_HIGH 0x1424
+#define MVPP22_TAI_TOD_STEP_FRAC_LOW 0x1428
+#define MVPP22_TAI_TAPDC_HIGH 0x142c
+#define MVPP22_TAI_TAPDC_LOW 0x1430
+#define MVPP22_TAI_TGTOD_SEC_HIGH 0x1434
+#define MVPP22_TAI_TGTOD_SEC_MED 0x1438
+#define MVPP22_TAI_TGTOD_SEC_LOW 0x143c
+#define MVPP22_TAI_TGTOD_NANO_HIGH 0x1440
+#define MVPP22_TAI_TGTOD_NANO_LOW 0x1444
+#define MVPP22_TAI_TGTOD_FRAC_HIGH 0x1448
+#define MVPP22_TAI_TGTOD_FRAC_LOW 0x144c
+#define MVPP22_TAI_TLV_SEC_HIGH 0x1450
+#define MVPP22_TAI_TLV_SEC_MED 0x1454
+#define MVPP22_TAI_TLV_SEC_LOW 0x1458
+#define MVPP22_TAI_TLV_NANO_HIGH 0x145c
+#define MVPP22_TAI_TLV_NANO_LOW 0x1460
+#define MVPP22_TAI_TLV_FRAC_HIGH 0x1464
+#define MVPP22_TAI_TLV_FRAC_LOW 0x1468
+#define MVPP22_TAI_TCV0_SEC_HIGH 0x146c
+#define MVPP22_TAI_TCV0_SEC_MED 0x1470
+#define MVPP22_TAI_TCV0_SEC_LOW 0x1474
+#define MVPP22_TAI_TCV0_NANO_HIGH 0x1478
+#define MVPP22_TAI_TCV0_NANO_LOW 0x147c
+#define MVPP22_TAI_TCV0_FRAC_HIGH 0x1480
+#define MVPP22_TAI_TCV0_FRAC_LOW 0x1484
+#define MVPP22_TAI_TCV1_SEC_HIGH 0x1488
+#define MVPP22_TAI_TCV1_SEC_MED 0x148c
+#define MVPP22_TAI_TCV1_SEC_LOW 0x1490
+#define MVPP22_TAI_TCV1_NANO_HIGH 0x1494
+#define MVPP22_TAI_TCV1_NANO_LOW 0x1498
+#define MVPP22_TAI_TCV1_FRAC_HIGH 0x149c
+#define MVPP22_TAI_TCV1_FRAC_LOW 0x14a0
+#define MVPP22_TAI_TCSR 0x14a4
+#define MVPP22_TAI_TUC_LSB 0x14a8
+#define MVPP22_TAI_GFM_SEC_HIGH 0x14ac
+#define MVPP22_TAI_GFM_SEC_MED 0x14b0
+#define MVPP22_TAI_GFM_SEC_LOW 0x14b4
+#define MVPP22_TAI_GFM_NANO_HIGH 0x14b8
+#define MVPP22_TAI_GFM_NANO_LOW 0x14bc
+#define MVPP22_TAI_GFM_FRAC_HIGH 0x14c0
+#define MVPP22_TAI_GFM_FRAC_LOW 0x14c4
+#define MVPP22_TAI_PCLK_DA_HIGH 0x14c8
+#define MVPP22_TAI_PCLK_DA_LOW 0x14cc
+#define MVPP22_TAI_CTCR 0x14d0
+#define MVPP22_TAI_PCLK_CCC_HIGH 0x14d4
+#define MVPP22_TAI_PCLK_CCC_LOW 0x14d8
+#define MVPP22_TAI_DTC_HIGH 0x14dc
+#define MVPP22_TAI_DTC_LOW 0x14e0
+#define MVPP22_TAI_CCC_HIGH 0x14e4
+#define MVPP22_TAI_CCC_LOW 0x14e8
+#define MVPP22_TAI_ICICE 0x14f4
+#define MVPP22_TAI_ICICC_LOW 0x14f8
+#define MVPP22_TAI_TUC_MSB 0x14fc
+
#define MVPP22_GMAC_BASE(port) (0x7000 + (port) * 0x1000 + 0xe00)
#define MVPP2_CAUSE_TXQ_SENT_DESC_ALL_MASK 0xff
@@ -531,6 +595,39 @@
#define MVPP22_XPCS_CFG0_PCS_MODE(n) ((n) << 3)
#define MVPP22_XPCS_CFG0_ACTIVE_LANE(n) ((n) << 5)
+/* PTP registers. PPv2.2 only */
+#define MVPP22_PTP_BASE(port) (0x7800 + (port * 0x1000))
+#define MVPP22_PTP_INT_CAUSE 0x00
+#define MVPP22_PTP_INT_MASK 0x04
+#define MVPP22_PTP_GCR 0x08
+#define MVPP22_PTP_TX_Q0_R0 0x0c
+#define MVPP22_PTP_TX_Q0_R1 0x10
+#define MVPP22_PTP_TX_Q0_R2 0x14
+#define MVPP22_PTP_TX_Q1_R0 0x18
+#define MVPP22_PTP_TX_Q1_R1 0x1c
+#define MVPP22_PTP_TX_Q1_R2 0x20
+#define MVPP22_PTP_TPCR 0x24
+#define MVPP22_PTP_V1PCR 0x28
+#define MVPP22_PTP_V2PCR 0x2c
+#define MVPP22_PTP_Y1731PCR 0x30
+#define MVPP22_PTP_NTPTSPCR 0x34
+#define MVPP22_PTP_NTPRXPCR 0x38
+#define MVPP22_PTP_NTPTXPCR 0x3c
+#define MVPP22_PTP_WAMPPCR 0x40
+#define MVPP22_PTP_NAPCR 0x44
+#define MVPP22_PTP_FAPCR 0x48
+#define MVPP22_PTP_CAPCR 0x50
+#define MVPP22_PTP_ATAPCR 0x54
+#define MVPP22_PTP_ACTAPCR 0x58
+#define MVPP22_PTP_CATAPCR 0x5c
+#define MVPP22_PTP_CACTAPCR 0x60
+#define MVPP22_PTP_AITAPCR 0x64
+#define MVPP22_PTP_CAITAPCR 0x68
+#define MVPP22_PTP_CITAPCR 0x6c
+#define MVPP22_PTP_NTP_OFF_HIGH 0x70
+#define MVPP22_PTP_NTP_OFF_LOW 0x74
+#define MVPP22_PTP_TX_PIPE_STATUS_DELAY 0x78
+
/* System controller registers. Accessed through a regmap. */
#define GENCONF_SOFT_RESET1 0x1108
#define GENCONF_SOFT_RESET1_GOP BIT(6)
@@ -763,6 +860,8 @@ enum mvpp2_prs_l3_cast {
#define MVPP2_DESC_DMA_MASK DMA_BIT_MASK(40)
+struct mvpp2_tai;
+
/* Definitions */
struct mvpp2_dbgfs_entries;
@@ -798,6 +897,7 @@ struct mvpp2 {
/* List of pointers to port structures */
int port_count;
struct mvpp2_port *port_list[MVPP2_MAX_PORTS];
+ struct mvpp2_tai *tai;
/* Number of Tx threads used */
unsigned int nthreads;
@@ -1253,4 +1353,13 @@ void mvpp2_dbgfs_init(struct mvpp2 *priv, const char *name);
void mvpp2_dbgfs_cleanup(struct mvpp2 *priv);
+#ifdef CONFIG_MVPP2_PTP
+int mvpp22_tai_probe(struct device *dev, struct mvpp2 *priv);
+#else
+static inline int mvpp22_tai_probe(struct device *dev, struct mvpp2 *priv)
+{
+ return 0;
+}
+#endif
+
#endif
@@ -6674,6 +6674,10 @@ static int mvpp2_probe(struct platform_device *pdev)
goto err_axi_clk;
}
+ err = mvpp22_tai_probe(&pdev->dev, priv);
+ if (err < 0)
+ goto err_axi_clk;
+
/* Initialize ports */
fwnode_for_each_available_child_node(fwnode, port_fwnode) {
err = mvpp2_port_probe(pdev, port_fwnode, priv);
new file mode 100644
@@ -0,0 +1,400 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Marvell PP2.2 TAI support
+ *
+ * Note:
+ * Do NOT use the event capture support.
+ * Do Not even set the MPP muxes to allow PTP_EVENT_REQ to be used.
+ * It will disrupt the operation of this driver, and there is nothing
+ * that this driver can do to prevent that. Even using PTP_EVENT_REQ
+ * as an output will be seen as a trigger input, which can't be masked.
+ * When ever a trigger input is seen, the action in the TCFCR0_TCF
+ * field will be performed - whether it is a set, increment, decrement
+ * read, or frequency update.
+ *
+ * Other notes (useful, not specified in the documentation):
+ * - PTP_PULSE_OUT (PTP_EVENT_REQ MPP)
+ * It looks like the hardware can't generate a pulse at nsec=0. (The
+ * output doesn't trigger if the nsec field is zero.)
+ * Note: when configured as an output via the register at 0xfX441120,
+ * the input is still very much alive, and will trigger the current TCF
+ * function.
+ * - PTP_CLK_OUT (PTP_TRIG_GEN MPP)
+ * This generates a "PPS" signal determined by the CCC registers. It
+ * seems this is not aligned to the TOD counter in any way (it may be
+ * initially, but if you specify a non-round second interval, it won't,
+ * and you can't easily get it back.)
+ * - PTP_PCLK_OUT
+ * This generates a 50% duty cycle clock based on the TOD counter, and
+ * seems it can be set to any period of 1ns resolution. It is probably
+ * limited by the TOD step size. Its period is defined by the PCLK_CCC
+ * registers. Again, its alignment to the second is questionable.
+ *
+ * Consequently, we support none of these.
+ */
+#include <linux/io.h>
+#include <linux/ptp_clock_kernel.h>
+#include <linux/slab.h>
+
+#include "mvpp2.h"
+
+#define CR0_SW_NRESET BIT(0)
+
+#define TCFCR0_PHASE_UPDATE_ENABLE BIT(8)
+#define TCFCR0_TCF_MASK (7 << 2)
+#define TCFCR0_TCF_UPDATE (0 << 2)
+#define TCFCR0_TCF_FREQUPDATE (1 << 2)
+#define TCFCR0_TCF_INCREMENT (2 << 2)
+#define TCFCR0_TCF_DECREMENT (3 << 2)
+#define TCFCR0_TCF_CAPTURE (4 << 2)
+#define TCFCR0_TCF_NOP (7 << 2)
+#define TCFCR0_TCF_TRIGGER BIT(0)
+
+#define TCSR_CAPTURE_1_VALID BIT(1)
+#define TCSR_CAPTURE_0_VALID BIT(0)
+
+struct mvpp2_tai {
+ struct ptp_clock_info caps;
+ struct ptp_clock *ptp_clock;
+ void __iomem *base;
+ spinlock_t lock;
+ u64 period; // nanosecond period in 32.32 fixed point
+};
+
+static void mvpp2_tai_modify(void __iomem *reg, u32 mask, u32 set)
+{
+ u32 val;
+
+ val = readl_relaxed(reg) & ~mask;
+ val |= set & mask;
+ writel(val, reg);
+}
+
+static void mvpp2_tai_write(u32 val, void __iomem *reg)
+{
+ writel_relaxed(val & 0xffff, reg);
+}
+
+static u32 mvpp2_tai_read(void __iomem *reg)
+{
+ return readl_relaxed(reg) & 0xffff;
+}
+
+static struct mvpp2_tai *ptp_to_tai(struct ptp_clock_info *ptp)
+{
+ return container_of(ptp, struct mvpp2_tai, caps);
+}
+
+static void mvpp22_tai_read_ts(struct timespec64 *ts, void __iomem *base)
+{
+ ts->tv_sec = (u64)mvpp2_tai_read(base + 0) << 32 |
+ mvpp2_tai_read(base + 4) << 16 |
+ mvpp2_tai_read(base + 8);
+
+ ts->tv_nsec = mvpp2_tai_read(base + 12) << 16 |
+ mvpp2_tai_read(base + 16);
+
+ /* Read and discard fractional part */
+ readl_relaxed(base + 20);
+ readl_relaxed(base + 24);
+}
+
+static void mvpp2_tai_write_tlv(const struct timespec64 *ts, u32 frac,
+ void __iomem *base)
+{
+ mvpp2_tai_write(ts->tv_sec >> 32, base + MVPP22_TAI_TLV_SEC_HIGH);
+ mvpp2_tai_write(ts->tv_sec >> 16, base + MVPP22_TAI_TLV_SEC_MED);
+ mvpp2_tai_write(ts->tv_sec, base + MVPP22_TAI_TLV_SEC_LOW);
+ mvpp2_tai_write(ts->tv_nsec >> 16, base + MVPP22_TAI_TLV_NANO_HIGH);
+ mvpp2_tai_write(ts->tv_nsec, base + MVPP22_TAI_TLV_NANO_LOW);
+ mvpp2_tai_write(frac >> 16, base + MVPP22_TAI_TLV_FRAC_HIGH);
+ mvpp2_tai_write(frac, base + MVPP22_TAI_TLV_FRAC_LOW);
+}
+
+static void mvpp2_tai_op(u32 op, void __iomem *base)
+{
+ /* Trigger the operation. Note that an external unmaskable
+ * event on PTP_EVENT_REQ will also trigger this action.
+ */
+ mvpp2_tai_modify(base + MVPP22_TAI_TCFCR0,
+ TCFCR0_TCF_MASK | TCFCR0_TCF_TRIGGER,
+ op | TCFCR0_TCF_TRIGGER);
+ mvpp2_tai_modify(base + MVPP22_TAI_TCFCR0, TCFCR0_TCF_MASK,
+ TCFCR0_TCF_NOP);
+}
+
+/* The adjustment has a range of +0.5ns to -0.5ns in 2^32 steps, so has units
+ * of 2^-32 ns.
+ *
+ * units(s) = 1 / (2^32 * 10^9)
+ * fractional = abs_scaled_ppm / (2^16 * 10^6)
+ *
+ * What we want to achieve:
+ * freq_adjusted = freq_nominal * (1 + fractional)
+ * freq_delta = freq_adjusted - freq_nominal => positive = faster
+ * freq_delta = freq_nominal * (1 + fractional) - freq_nominal
+ * So: freq_delta = freq_nominal * fractional
+ *
+ * However, we are dealing with periods, so:
+ * period_adjusted = period_nominal / (1 + fractional)
+ * period_delta = period_nominal - period_adjusted => positive = faster
+ * period_delta = period_nominal * fractional / (1 + fractional)
+ *
+ * Hence:
+ * period_delta = period_nominal * abs_scaled_ppm /
+ * (2^16 * 10^6 + abs_scaled_ppm)
+ *
+ * To avoid overflow, we reduce both sides of the divide operation by a factor
+ * of 16.
+ */
+static u64 mvpp22_calc_frac_ppm(struct mvpp2_tai *tai, long abs_scaled_ppm)
+{
+ u64 val = tai->period * abs_scaled_ppm >> 4;
+
+ return div_u64(val, (1000000 << 12) + (abs_scaled_ppm >> 4));
+}
+
+static s32 mvpp22_calc_max_adj(struct mvpp2_tai *tai)
+{
+ return 1000000;
+}
+
+static int mvpp22_tai_adjfine(struct ptp_clock_info *ptp, long scaled_ppm)
+{
+ struct mvpp2_tai *tai = ptp_to_tai(ptp);
+ unsigned long flags;
+ void __iomem *base;
+ bool neg_adj;
+ s32 frac;
+ u64 val;
+
+ neg_adj = scaled_ppm < 0;
+ if (neg_adj)
+ scaled_ppm = -scaled_ppm;
+
+ val = mvpp22_calc_frac_ppm(tai, scaled_ppm);
+
+ /* Convert to a signed 32-bit adjustment */
+ if (neg_adj) {
+ /* -S32_MIN warns, -val < S32_MIN fails, so go for the easy
+ * solution.
+ */
+ if (val > 0x80000000)
+ return -ERANGE;
+
+ frac = -val;
+ } else {
+ if (val > S32_MAX)
+ return -ERANGE;
+
+ frac = val;
+ }
+
+ base = tai->base;
+ spin_lock_irqsave(&tai->lock, flags);
+ mvpp2_tai_write(frac >> 16, base + MVPP22_TAI_TLV_FRAC_HIGH);
+ mvpp2_tai_write(frac, base + MVPP22_TAI_TLV_FRAC_LOW);
+ mvpp2_tai_op(TCFCR0_TCF_FREQUPDATE, base);
+ spin_unlock_irqrestore(&tai->lock, flags);
+
+ return 0;
+}
+
+static int mvpp22_tai_adjtime(struct ptp_clock_info *ptp, s64 delta)
+{
+ struct mvpp2_tai *tai = ptp_to_tai(ptp);
+ struct timespec64 ts;
+ unsigned long flags;
+ void __iomem *base;
+ u32 tcf;
+
+ /* We can't deal with S64_MIN */
+ if (delta == S64_MIN)
+ return -ERANGE;
+
+ if (delta < 0) {
+ delta = -delta;
+ tcf = TCFCR0_TCF_DECREMENT;
+ } else {
+ tcf = TCFCR0_TCF_INCREMENT;
+ }
+
+ ts = ns_to_timespec64(delta);
+
+ base = tai->base;
+ spin_lock_irqsave(&tai->lock, flags);
+ mvpp2_tai_write_tlv(&ts, 0, base);
+ mvpp2_tai_op(tcf, base);
+ spin_unlock_irqrestore(&tai->lock, flags);
+
+ return 0;
+}
+
+static int mvpp22_tai_gettimex64(struct ptp_clock_info *ptp,
+ struct timespec64 *ts,
+ struct ptp_system_timestamp *sts)
+{
+ struct mvpp2_tai *tai = ptp_to_tai(ptp);
+ unsigned long flags;
+ void __iomem *base;
+ u32 tcsr;
+ int ret;
+
+ base = tai->base;
+ spin_lock_irqsave(&tai->lock, flags);
+ /* XXX: the only way to read the PTP time is for the CPU to trigger
+ * an event. However, there is no way to distinguish between the CPU
+ * triggered event, and an external event on PTP_EVENT_REQ. So this
+ * is incompatible with external use of PTP_EVENT_REQ.
+ */
+ ptp_read_system_prets(sts);
+ mvpp2_tai_modify(base + MVPP22_TAI_TCFCR0,
+ TCFCR0_TCF_MASK | TCFCR0_TCF_TRIGGER,
+ TCFCR0_TCF_CAPTURE | TCFCR0_TCF_TRIGGER);
+ ptp_read_system_postts(sts);
+ mvpp2_tai_modify(base + MVPP22_TAI_TCFCR0, TCFCR0_TCF_MASK,
+ TCFCR0_TCF_NOP);
+
+ tcsr = readl(base + MVPP22_TAI_TCSR);
+ if (tcsr & TCSR_CAPTURE_1_VALID) {
+ mvpp22_tai_read_ts(ts, base + MVPP22_TAI_TCV1_SEC_HIGH);
+ ret = 0;
+ } else if (tcsr & TCSR_CAPTURE_0_VALID) {
+ mvpp22_tai_read_ts(ts, base + MVPP22_TAI_TCV0_SEC_HIGH);
+ ret = 0;
+ } else {
+ /* We don't seem to have a reading... */
+ ret = -EBUSY;
+ }
+ spin_unlock_irqrestore(&tai->lock, flags);
+
+ return ret;
+}
+
+static int mvpp22_tai_settime64(struct ptp_clock_info *ptp,
+ const struct timespec64 *ts)
+{
+ struct mvpp2_tai *tai = ptp_to_tai(ptp);
+ unsigned long flags;
+ void __iomem *base;
+
+ base = tai->base;
+ spin_lock_irqsave(&tai->lock, flags);
+ mvpp2_tai_write_tlv(ts, 0, base);
+
+ /* Trigger an update to load the value from the TLV registers
+ * into the TOD counter. Note that an external unmaskable event on
+ * PTP_EVENT_REQ will also trigger this action.
+ */
+ mvpp2_tai_modify(base + MVPP22_TAI_TCFCR0,
+ TCFCR0_PHASE_UPDATE_ENABLE |
+ TCFCR0_TCF_MASK | TCFCR0_TCF_TRIGGER,
+ TCFCR0_TCF_UPDATE | TCFCR0_TCF_TRIGGER);
+ mvpp2_tai_modify(base + MVPP22_TAI_TCFCR0, TCFCR0_TCF_MASK,
+ TCFCR0_TCF_NOP);
+ spin_unlock_irqrestore(&tai->lock, flags);
+
+ return 0;
+}
+
+static void mvpp22_tai_set_step(struct mvpp2_tai *tai)
+{
+ void __iomem *base = tai->base;
+ u32 nano, frac;
+
+ nano = upper_32_bits(tai->period);
+ frac = lower_32_bits(tai->period);
+
+ /* As the fractional nanosecond is a signed offset, if the MSB (sign)
+ * bit is set, we have to increment the whole nanoseconds.
+ */
+ if (frac >= 0x80000000)
+ nano += 1;
+
+ mvpp2_tai_write(nano, base + MVPP22_TAI_TOD_STEP_NANO_CR);
+ mvpp2_tai_write(frac >> 16, base + MVPP22_TAI_TOD_STEP_FRAC_HIGH);
+ mvpp2_tai_write(frac, base + MVPP22_TAI_TOD_STEP_FRAC_LOW);
+}
+
+static void mvpp22_tai_init(struct mvpp2_tai *tai)
+{
+ void __iomem *base = tai->base;
+
+ mvpp22_tai_set_step(tai);
+
+ /* Release the TAI reset */
+ mvpp2_tai_modify(base + MVPP22_TAI_CR0, CR0_SW_NRESET, CR0_SW_NRESET);
+}
+
+static void mvpp22_tai_remove(void *priv)
+{
+ struct mvpp2_tai *tai = priv;
+
+ if (!IS_ERR(tai->ptp_clock))
+ ptp_clock_unregister(tai->ptp_clock);
+}
+
+int mvpp22_tai_probe(struct device *dev, struct mvpp2 *priv)
+{
+ struct mvpp2_tai *tai;
+ int ret;
+
+ tai = devm_kzalloc(dev, sizeof(*tai), GFP_KERNEL);
+ if (!tai)
+ return -ENOMEM;
+
+ spin_lock_init(&tai->lock);
+
+ tai->base = priv->iface_base;
+
+ /* The step size consists of three registers - a 16-bit nanosecond step
+ * size, and a 32-bit fractional nanosecond step size split over two
+ * registers. The fractional nanosecond step size has units of 2^-32ns.
+ *
+ * To calculate this, we calculate:
+ * (10^9 + freq / 2) / (freq * 2^-32)
+ * which gives us the nanosecond step to the nearest integer in 16.32
+ * fixed point format, and the fractional part of the step size with
+ * the MSB inverted. With rounding of the fractional nanosecond, and
+ * simplification, this becomes:
+ * (10^9 << 32 + freq << 31 + (freq + 1) >> 1) / freq
+ *
+ * So:
+ * div = (10^9 << 32 + freq << 31 + (freq + 1) >> 1) / freq
+ * nano = upper_32_bits(div);
+ * frac = lower_32_bits(div) ^ 0x80000000;
+ * Will give the values for the registers.
+ *
+ * This is all seems perfect, but alas it is not when considering the
+ * whole story. The system is clocked from 25MHz, which is multiplied
+ * by a PLL to 1GHz, and then divided by three, giving 333333333Hz
+ * (recurring). This gives exactly 3ns, but using 333333333Hz with
+ * the above gives an error of 13*2^-32ns.
+ *
+ * Consequently, we use the period rather than calculating from the
+ * frequency.
+ */
+ tai->period = 3ULL << 32;
+
+ mvpp22_tai_init(tai);
+
+ tai->caps.owner = THIS_MODULE;
+ strscpy(tai->caps.name, "Marvell PP2.2", sizeof(tai->caps.name));
+ tai->caps.max_adj = mvpp22_calc_max_adj(tai);
+ tai->caps.adjfine = mvpp22_tai_adjfine;
+ tai->caps.adjtime = mvpp22_tai_adjtime;
+ tai->caps.gettimex64 = mvpp22_tai_gettimex64;
+ tai->caps.settime64 = mvpp22_tai_settime64;
+
+ ret = devm_add_action(dev, mvpp22_tai_remove, tai);
+ if (ret)
+ return ret;
+
+ tai->ptp_clock = ptp_clock_register(&tai->caps, dev);
+ if (IS_ERR(tai->ptp_clock))
+ return PTR_ERR(tai->ptp_clock);
+
+ priv->tai = tai;
+
+ return 0;
+}