@@ -366,7 +366,6 @@ static void mmci_init_sg(struct mmci_host *host, struct mmc_data *data)
#ifdef CONFIG_DMA_ENGINE
static void mmci_dma_setup(struct mmci_host *host)
{
- struct mmci_platform_data *plat = host->plat;
const char *rxname, *txname;
dma_cap_mask_t mask;
@@ -380,25 +379,6 @@ static void mmci_dma_setup(struct mmci_host *host)
dma_cap_zero(mask);
dma_cap_set(DMA_SLAVE, mask);
- if (plat && plat->dma_filter) {
- if (!host->dma_rx_channel && plat->dma_rx_param) {
- host->dma_rx_channel = dma_request_channel(mask,
- plat->dma_filter,
- plat->dma_rx_param);
- /* E.g if no DMA hardware is present */
- if (!host->dma_rx_channel)
- dev_err(mmc_dev(host->mmc), "no RX DMA channel\n");
- }
-
- if (!host->dma_tx_channel && plat->dma_tx_param) {
- host->dma_tx_channel = dma_request_channel(mask,
- plat->dma_filter,
- plat->dma_tx_param);
- if (!host->dma_tx_channel)
- dev_warn(mmc_dev(host->mmc), "no TX DMA channel\n");
- }
- }
-
/*
* If only an RX channel is specified, the driver will
* attempt to use it bidirectionally, however if it is
@@ -446,11 +426,9 @@ static void mmci_dma_setup(struct mmci_host *host)
*/
static inline void mmci_dma_release(struct mmci_host *host)
{
- struct mmci_platform_data *plat = host->plat;
-
if (host->dma_rx_channel)
dma_release_channel(host->dma_rx_channel);
- if (host->dma_tx_channel && plat->dma_tx_param)
+ if (host->dma_tx_channel)
dma_release_channel(host->dma_tx_channel);
host->dma_rx_channel = host->dma_tx_channel = NULL;
}
@@ -6,9 +6,6 @@
#include <linux/mmc/host.h>
-/* Just some dummy forwarding */
-struct dma_chan;
-
/**
* struct mmci_platform_data - platform configuration for the MMCI
* (also known as PL180) block.
@@ -29,17 +26,6 @@ struct dma_chan;
* @gpio_wp: read this GPIO pin to see if the card is write protected
* @gpio_cd: read this GPIO pin to detect card insertion
* @cd_invert: true if the gpio_cd pin value is active low
- * @dma_filter: function used to select an appropriate RX and TX
- * DMA channel to be used for DMA, if and only if you're deploying the
- * generic DMA engine
- * @dma_rx_param: parameter passed to the DMA allocation
- * filter in order to select an appropriate RX channel. If
- * there is a bidirectional RX+TX channel, then just specify
- * this and leave dma_tx_param set to NULL
- * @dma_tx_param: parameter passed to the DMA allocation
- * filter in order to select an appropriate TX channel. If this
- * is NULL the driver will attempt to use the RX channel as a
- * bidirectional channel
*/
struct mmci_platform_data {
unsigned int f_max;
@@ -49,9 +35,6 @@ struct mmci_platform_data {
int gpio_wp;
int gpio_cd;
bool cd_invert;
- bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
- void *dma_rx_param;
- void *dma_tx_param;
};
#endif
Remove the option to provide DMA configuration as platform data, enforce it through DT. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> --- drivers/mmc/host/mmci.c | 24 +----------------------- include/linux/amba/mmci.h | 17 ----------------- 2 files changed, 1 insertion(+), 40 deletions(-)