@@ -64,6 +64,14 @@ typedef struct I440FXState {
*/
#define I440FX_COREBOOT_RAM_SIZE 0x57
+/* Older I440FX machines (5.0 and older) not support i440FX-pcihost state
+ * migration, use some reserved INTEL 82441 configuration registers to
+ * save/restore i440FX-pcihost config register. Refer to [INTEL 440FX PCISET
+ * 82441FX PCI AND MEMORY CONTROLLER (PMC) AND 82442FX DATA BUS ACCELERATOR
+ * (DBX) Table 1. PMC Configuration Space]
+ */
+#define I440FX_PCI_HOST_CONFIG_REG 0x94
+
static void i440fx_update_memory_mappings(PCII440FXState *d)
{
int i;
@@ -98,8 +106,30 @@ static void i440fx_write_config(PCIDevice *dev,
static int i440fx_post_load(void *opaque, int version_id)
{
PCII440FXState *d = opaque;
+ PCIDevice *dev;
+ PCIHostState *s = OBJECT_CHECK(PCIHostState,
+ object_resolve_path("/machine/i440fx", NULL),
+ TYPE_PCI_HOST_BRIDGE);
i440fx_update_memory_mappings(d);
+
+ if (!s->mig_enabled) {
+ dev = PCI_DEVICE(d);
+ s->config_reg = pci_get_long(&dev->config[I440FX_PCI_HOST_CONFIG_REG]);
+ }
+ return 0;
+}
+
+static int i440fx_pre_save(void *opaque)
+{
+ PCIDevice *dev = opaque;
+ PCIHostState *s = OBJECT_CHECK(PCIHostState,
+ object_resolve_path("/machine/i440fx", NULL),
+ TYPE_PCI_HOST_BRIDGE);
+ if (!s->mig_enabled) {
+ pci_set_long(&dev->config[I440FX_PCI_HOST_CONFIG_REG],
+ s->config_reg);
+ }
return 0;
}
@@ -107,6 +137,7 @@ static const VMStateDescription vmstate_i440fx = {
.name = "I440FX",
.version_id = 3,
.minimum_version_id = 3,
+ .pre_save = i440fx_pre_save,
.post_load = i440fx_post_load,
.fields = (VMStateField[]) {
VMSTATE_PCI_DEVICE(parent_obj, PCII440FXState),
@@ -43,6 +43,15 @@
#define Q35_PCI_HOST_HOLE64_SIZE_DEFAULT (1ULL << 35)
+/* Older Q35 machines (5.0 and older) not support q35-pcihost state
+ * migration, use some reserved INTEL MCH configuration registers to
+ * save/restore q35-pcihost config register. Refer to [Intel 3 Series
+ * Chipset Family Datasheet Table 5-1. DRAM Controller Register Address
+ * Map (D0:F0)]
+ */
+#define Q35_PCI_HOST_CONFIG_REG 0x70
+
+
static void q35_host_realize(DeviceState *dev, Error **errp)
{
PCIHostState *pci = PCI_HOST_BRIDGE(dev);
@@ -513,7 +522,27 @@ static void mch_update(MCHPCIState *mch)
static int mch_post_load(void *opaque, int version_id)
{
MCHPCIState *mch = opaque;
+ PCIDevice *dev;
+ PCIHostState *s = OBJECT_CHECK(PCIHostState,
+ object_resolve_path("/machine/q35", NULL),
+ TYPE_PCI_HOST_BRIDGE);
mch_update(mch);
+ if (!s->mig_enabled) {
+ dev = PCI_DEVICE(mch);
+ s->config_reg = pci_get_long(&dev->config[Q35_PCI_HOST_CONFIG_REG]);
+ }
+ return 0;
+}
+
+static int mch_pre_save(void *opaque)
+{
+ PCIDevice *dev = opaque;
+ PCIHostState *s = OBJECT_CHECK(PCIHostState,
+ object_resolve_path("/machine/q35", NULL),
+ TYPE_PCI_HOST_BRIDGE);
+ if (!s->mig_enabled) {
+ pci_set_long(&dev->config[Q35_PCI_HOST_CONFIG_REG], s->config_reg);
+ }
return 0;
}
@@ -521,6 +550,7 @@ static const VMStateDescription vmstate_mch = {
.name = "mch",
.version_id = 1,
.minimum_version_id = 1,
+ .pre_save = mch_pre_save,
.post_load = mch_post_load,
.fields = (VMStateField[]) {
VMSTATE_PCI_DEVICE(parent_obj, MCHPCIState),
The i440fx and q35 machines integrate i440FX or MCH PCI device by default. Refer to i440FX and ICH9-LPC spcifications, there are some reserved configuration registers can used to save/restore PCIHostState.config_reg. It's nasty but friendly to old ones. Reproducer steps: step 1. Make modifications to seabios and qemu for increase reproduction efficiency, write 0xf0 to 0x402 port notify qemu to stop vcpu after 0x0cf8 port wrote i440 configure register. qemu stop vcpu when catch 0x402 port wrote 0xf0. seabios:/src/hw/pci.c @@ -52,6 +52,11 @@ void pci_config_writeb(u16 bdf, u32 addr, u8 val) writeb(mmconfig_addr(bdf, addr), val); } else { outl(ioconfig_cmd(bdf, addr), PORT_PCI_CMD); + if (bdf == 0 && addr == 0x72 && val == 0xa) { + dprintf(1, "stop vcpu\n"); + outb(0xf0, 0x402); // notify qemu to stop vcpu + dprintf(1, "resume vcpu\n"); + } outb(val, PORT_PCI_DATA + (addr & 3)); } } qemu:hw/char/debugcon.c @@ -60,6 +61,9 @@ static void debugcon_ioport_write(void *opaque, hwaddr addr, uint64_t val, printf(" [debugcon: write addr=0x%04" HWADDR_PRIx " val=0x%02" PRIx64 "]\n", addr, val); #endif + if (ch == 0xf0) { + vm_stop(RUN_STATE_PAUSED); + } /* XXX this blocks entire thread. Rewrite to use * qemu_chr_fe_write and background I/O callbacks */ qemu_chr_fe_write_all(&s->chr, &ch, 1); step 2. start vm1 by the following command line, and then vm stopped. $ qemu-system-x86_64 -machine pc-i440fx-5.0,accel=kvm\ -netdev tap,ifname=tap-test,id=hostnet0,vhost=on,downscript=no,script=no\ -device virtio-net-pci,netdev=hostnet0,id=net0,bus=pci.0,addr=0x13,bootindex=3\ -device cirrus-vga,id=video0,vgamem_mb=16,bus=pci.0,addr=0x2\ -chardev file,id=seabios,path=/var/log/test.seabios,append=on\ -device isa-debugcon,iobase=0x402,chardev=seabios\ -monitor stdio step 3. start vm2 to accept vm1 state. $ qemu-system-x86_64 -machine pc-i440fx-5.0,accel=kvm\ -netdev tap,ifname=tap-test1,id=hostnet0,vhost=on,downscript=no,script=no\ -device virtio-net-pci,netdev=hostnet0,id=net0,bus=pci.0,addr=0x13,bootindex=3\ -device cirrus-vga,id=video0,vgamem_mb=16,bus=pci.0,addr=0x2\ -chardev file,id=seabios,path=/var/log/test.seabios,append=on\ -device isa-debugcon,iobase=0x402,chardev=seabios\ -monitor stdio \ -incoming tcp:127.0.0.1:8000 step 4. execute the following qmp command in vm1 to migrate. (qemu) migrate tcp:127.0.0.1:8000 step 5. execute the following qmp command in vm2 to resume vcpu. (qemu) cont Before this patch, we can get KVM "emulation failure" error on vm2. This patch can fix it. Signed-off-by: Hogan Wang <hogan.wang@huawei.com> --- hw/pci-host/i440fx.c | 31 +++++++++++++++++++++++++++++++ hw/pci-host/q35.c | 30 ++++++++++++++++++++++++++++++ 2 files changed, 61 insertions(+)