Message ID | 20200909195640.3127341-5-robert.marko@sartura.hr |
---|---|
State | New |
Headers | show |
Series | arm: dts: qcom: ipq4019: add more boards | expand |
On Wed, Sep 9, 2020 at 9:56 PM Robert Marko <robert.marko@sartura.hr> wrote: > > 8devices Habanero DVK is a dual-band SoM development kit based on Qualcomm > IPQ4019 + QCA8075 platform. > > Specs are: > CPU: QCA IPQ4019 > RAM: DDR3L 512MB > Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without) > WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2 > WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2 > Ethernet: 5x Gbit LAN (QCA 8075) > USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019) > MicroSD slot (Uses SD controller built into IPQ4019) > SDIO3.0/EMMC slot (Uses the same SD controller) > Mini PCI-E Gen 2.0 slot (Built into IPQ4019) > 5x LEDs (4 GPIO controllable) > 2x Pushbutton (1 is connected to GPIO, other to SoC reset) > LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support) > 1x UART 115200 rate on J18 > > 2x breakout development headers > 12V DC Jack for power > DIP switch for bootstrap configuration > > Signed-off-by: Robert Marko <robert.marko@sartura.hr> > Cc: Luka Perkov <luka.perkov@sartura.hr> > --- > Changes since v1: > * Drop include that does not exist > > arch/arm/boot/dts/Makefile | 1 + > .../boot/dts/qcom-ipq4019-habanero-dvk.dts | 304 ++++++++++++++++++ > 2 files changed, 305 insertions(+) > create mode 100644 arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 246d82fc5fcd..004262e0d699 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -898,6 +898,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \ > qcom-ipq4019-ap.dk04.1-c3.dtb \ > qcom-ipq4019-ap.dk07.1-c1.dtb \ > qcom-ipq4019-ap.dk07.1-c2.dtb \ > + qcom-ipq4019-habanero-dvk.dtb \ > qcom-ipq8064-ap148.dtb \ > qcom-ipq8064-rb3011.dtb \ > qcom-msm8660-surf.dtb \ > diff --git a/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts b/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts > new file mode 100644 > index 000000000000..fe054adda0a7 > --- /dev/null > +++ b/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts > @@ -0,0 +1,304 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > +/* Copyright (c) 2019, Robert Marko <robimarko@gmail.com> */ > + > +#include "qcom-ipq4019.dtsi" > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > + > +/ { > + model = "8devices Habanero DVK"; > + compatible = "8dev,habanero-dvk"; > + > + keys { > + compatible = "gpio-keys"; > + > + reset { > + label = "reset"; > + gpios = <&tlmm 8 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_RESTART>; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + led_status: status { > + label = "habanero-dvk:green:status"; > + gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>; > + panic-indicator; > + }; > + > + led_upgrade: upgrade { > + label = "habanero-dvk:green:upgrade"; > + gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>; > + }; > + > + wlan2g { > + label = "habanero-dvk:green:wlan2g"; > + gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "phy0tpt"; > + }; > + > + wlan5g { > + label = "habanero-dvk:green:wlan5g"; > + gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "phy1tpt"; > + }; > + }; > +}; > + > +&vqmmc { > + status = "okay"; > +}; > + > +&sdhci { > + status = "okay"; > + > + pinctrl-0 = <&sd_pins>; > + pinctrl-names = "default"; > + cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; > + vqmmc-supply = <&vqmmc>; > +}; > + > +&qpic_bam { > + status = "okay"; > +}; > + > +&tlmm { > + mdio_pins: mdio_pinmux { > + mux_1 { > + pins = "gpio6"; > + function = "mdio"; > + bias-pull-up; > + }; > + > + mux_2 { > + pins = "gpio7"; > + function = "mdc"; > + bias-pull-up; > + }; > + }; > + > + serial_pins: serial_pinmux { > + mux { > + pins = "gpio16", "gpio17"; > + function = "blsp_uart0"; > + bias-disable; > + }; > + }; > + > + spi_0_pins: spi_0_pinmux { > + pinmux { > + function = "blsp_spi0"; > + pins = "gpio13", "gpio14", "gpio15"; > + drive-strength = <12>; > + bias-disable; > + }; > + > + pinmux_cs { > + function = "gpio"; > + pins = "gpio12"; > + drive-strength = <2>; > + bias-disable; > + output-high; > + }; > + }; > + > + nand_pins: nand_pins { > + pullups { > + pins = "gpio52", "gpio53", "gpio58", "gpio59"; > + function = "qpic"; > + bias-pull-up; > + }; > + > + pulldowns { > + pins = "gpio54", "gpio55", "gpio56", "gpio57", > + "gpio60", "gpio62", "gpio63", "gpio64", > + "gpio65", "gpio66", "gpio67", "gpio68", > + "gpio69"; > + function = "qpic"; > + bias-pull-down; > + }; > + }; > + > + sd_pins: sd_pins { > + pinmux { > + function = "sdio"; > + pins = "gpio23", "gpio24", "gpio25", "gpio26", > + "gpio28", "gpio29", "gpio30", "gpio31"; > + drive-strength = <10>; > + }; > + > + pinmux_sd_clk { > + function = "sdio"; > + pins = "gpio27"; > + drive-strength = <16>; > + }; > + > + pinmux_sd7 { > + function = "sdio"; > + pins = "gpio32"; > + drive-strength = <10>; > + bias-disable; > + }; > + }; > +}; > + > +&watchdog { > + status = "okay"; > +}; > + > +&prng { > + status = "okay"; > +}; > + > +&blsp_dma { > + status = "okay"; > +}; > + > +&blsp1_spi1 { > + status = "okay"; > + > + pinctrl-0 = <&spi_0_pins>; > + pinctrl-names = "default"; > + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; > + > + flash@0 { > + compatible = "jedec,spi-nor"; > + spi-max-frequency = <24000000>; > + reg = <0>; > + > + partitions { > + compatible = "fixed-partitions"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + partition@0 { > + label = "SBL1"; > + reg = <0x00000000 0x00040000>; > + read-only; > + }; > + partition@40000 { > + label = "MIBIB"; > + reg = <0x00040000 0x00020000>; > + read-only; > + }; > + partition@60000 { > + label = "QSEE"; > + reg = <0x00060000 0x00060000>; > + read-only; > + }; > + partition@c0000 { > + label = "CDT"; > + reg = <0x000c0000 0x00010000>; > + read-only; > + }; > + partition@d0000 { > + label = "DDRPARAMS"; > + reg = <0x000d0000 0x00010000>; > + read-only; > + }; > + partition@e0000 { > + label = "APPSBLENV"; /* uboot env */ > + reg = <0x000e0000 0x00010000>; > + read-only; > + }; > + partition@f0000 { > + label = "APPSBL"; /* uboot */ > + reg = <0x000f0000 0x00080000>; > + read-only; > + }; > + partition@170000 { > + label = "ART"; > + reg = <0x00170000 0x00010000>; > + read-only; > + }; > + partition@180000 { > + label = "cfg"; > + reg = <0x00180000 0x00040000>; > + }; > + partition@1c0000 { > + label = "firmware"; > + compatible = "denx,fit"; > + reg = <0x001c0000 0x01e40000>; > + }; > + }; > + }; > +}; > + > +/* Some DVK boards ship without NAND */ > +&nand { > + status = "okay"; > + > + pinctrl-0 = <&nand_pins>; > + pinctrl-names = "default"; > +}; > + > +&blsp1_uart1 { > + status = "okay"; > + > + pinctrl-0 = <&serial_pins>; > + pinctrl-names = "default"; > +}; > + > +&cryptobam { > + status = "okay"; > +}; > + > +&crypto { > + status = "okay"; > +}; > + > +&mdio { > + status = "okay"; > + > + pinctrl-0 = <&mdio_pins>; > + pinctrl-names = "default"; > +}; > + > +&pcie0 { > + status = "okay"; > + > + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; > + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; > + > + /* Free slot for use */ > + bridge@0,0 { > + reg = <0x00000000 0 0 0 0>; > + #address-cells = <3>; > + #size-cells = <2>; > + ranges; > + }; > +}; > + > +&wifi0 { > + status = "okay"; > + > + qcom,ath10k-calibration-variant = "8devices-Habanero"; > +}; > + > +&wifi1 { > + status = "okay"; > + > + qcom,ath10k-calibration-variant = "8devices-Habanero"; > +}; > + > +&usb3_ss_phy { > + status = "okay"; > +}; > + > +&usb3_hs_phy { > + status = "okay"; > +}; > + > +&usb3 { > + status = "okay"; > +}; > + > +&usb2_hs_phy { > + status = "okay"; > +}; > + > +&usb2 { > + status = "okay"; > +}; > -- > 2.26.2 > Hi, Is there an issue with the patch preventing the review? Regards, Robert
On Fri, Jan 22, 2021 at 7:56 PM Bjorn Andersson <bjorn.andersson@linaro.org> wrote: > > On Fri 02 Oct 12:41 CDT 2020, Robert Marko wrote: > > > On Wed, Sep 9, 2020 at 9:56 PM Robert Marko <robert.marko@sartura.hr> wrote: > > > > > > 8devices Habanero DVK is a dual-band SoM development kit based on Qualcomm > > > IPQ4019 + QCA8075 platform. > > > > > > Specs are: > > > CPU: QCA IPQ4019 > > > RAM: DDR3L 512MB > > > Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without) > > > WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2 > > > WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2 > > > Ethernet: 5x Gbit LAN (QCA 8075) > > > USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019) > > > MicroSD slot (Uses SD controller built into IPQ4019) > > > SDIO3.0/EMMC slot (Uses the same SD controller) > > > Mini PCI-E Gen 2.0 slot (Built into IPQ4019) > > > 5x LEDs (4 GPIO controllable) > > > 2x Pushbutton (1 is connected to GPIO, other to SoC reset) > > > LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support) > > > 1x UART 115200 rate on J18 > > > > > > 2x breakout development headers > > > 12V DC Jack for power > > > DIP switch for bootstrap configuration > > > > > > Signed-off-by: Robert Marko <robert.marko@sartura.hr> > > > Cc: Luka Perkov <luka.perkov@sartura.hr> > > > --- > > > Changes since v1: > > > * Drop include that does not exist > > > > > > arch/arm/boot/dts/Makefile | 1 + > > > .../boot/dts/qcom-ipq4019-habanero-dvk.dts | 304 ++++++++++++++++++ > > > 2 files changed, 305 insertions(+) > > > create mode 100644 arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts > > > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > > index 246d82fc5fcd..004262e0d699 100644 > > > --- a/arch/arm/boot/dts/Makefile > > > +++ b/arch/arm/boot/dts/Makefile > > > @@ -898,6 +898,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \ > > > qcom-ipq4019-ap.dk04.1-c3.dtb \ > > > qcom-ipq4019-ap.dk07.1-c1.dtb \ > > > qcom-ipq4019-ap.dk07.1-c2.dtb \ > > > + qcom-ipq4019-habanero-dvk.dtb \ > > > qcom-ipq8064-ap148.dtb \ > > > qcom-ipq8064-rb3011.dtb \ > > > qcom-msm8660-surf.dtb \ > > > diff --git a/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts b/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts > > > new file mode 100644 > > > index 000000000000..fe054adda0a7 > > > --- /dev/null > > > +++ b/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts > > > @@ -0,0 +1,304 @@ > > > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > > > +/* Copyright (c) 2019, Robert Marko <robimarko@gmail.com> */ > > > + > > > +#include "qcom-ipq4019.dtsi" > > > +#include <dt-bindings/gpio/gpio.h> > > > +#include <dt-bindings/input/input.h> > > > + > > > +/ { > > > + model = "8devices Habanero DVK"; > > > + compatible = "8dev,habanero-dvk"; > > > + > > > + keys { > > > + compatible = "gpio-keys"; > > > + > > > + reset { > > > + label = "reset"; > > > + gpios = <&tlmm 8 GPIO_ACTIVE_LOW>; > > > + linux,code = <KEY_RESTART>; > > > + }; > > > + }; > > > + > > > + leds { > > > + compatible = "gpio-leds"; > > > + > > > + led_status: status { > > > + label = "habanero-dvk:green:status"; > > > + gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>; > > > + panic-indicator; > > > + }; > > > + > > > + led_upgrade: upgrade { > > > + label = "habanero-dvk:green:upgrade"; > > > + gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>; > > > + }; > > > + > > > + wlan2g { > > > + label = "habanero-dvk:green:wlan2g"; > > > + gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>; > > > + linux,default-trigger = "phy0tpt"; > > > + }; > > > + > > > + wlan5g { > > > + label = "habanero-dvk:green:wlan5g"; > > > + gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>; > > > + linux,default-trigger = "phy1tpt"; > > > + }; > > > + }; > > > +}; > > > + > > > +&vqmmc { > > > + status = "okay"; > > > +}; > > > + > > > +&sdhci { > > > + status = "okay"; > > > + > > > + pinctrl-0 = <&sd_pins>; > > > + pinctrl-names = "default"; > > > + cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; > > > + vqmmc-supply = <&vqmmc>; > > > +}; > > > + > > > +&qpic_bam { > > > + status = "okay"; > > > +}; > > > + > > > +&tlmm { > > > + mdio_pins: mdio_pinmux { > > > + mux_1 { > > > + pins = "gpio6"; > > > + function = "mdio"; > > > + bias-pull-up; > > > + }; > > > + > > > + mux_2 { > > > + pins = "gpio7"; > > > + function = "mdc"; > > > + bias-pull-up; > > > + }; > > > + }; > > > + > > > + serial_pins: serial_pinmux { > > > + mux { > > > + pins = "gpio16", "gpio17"; > > > + function = "blsp_uart0"; > > > + bias-disable; > > > + }; > > > + }; > > > + > > > + spi_0_pins: spi_0_pinmux { > > > + pinmux { > > > + function = "blsp_spi0"; > > > + pins = "gpio13", "gpio14", "gpio15"; > > > + drive-strength = <12>; > > > + bias-disable; > > > + }; > > > + > > > + pinmux_cs { > > > + function = "gpio"; > > > + pins = "gpio12"; > > > + drive-strength = <2>; > > > + bias-disable; > > > + output-high; > > > + }; > > > + }; > > > + > > > + nand_pins: nand_pins { > > > + pullups { > > > + pins = "gpio52", "gpio53", "gpio58", "gpio59"; > > > + function = "qpic"; > > > + bias-pull-up; > > > + }; > > > + > > > + pulldowns { > > > + pins = "gpio54", "gpio55", "gpio56", "gpio57", > > > + "gpio60", "gpio62", "gpio63", "gpio64", > > > + "gpio65", "gpio66", "gpio67", "gpio68", > > > + "gpio69"; > > > + function = "qpic"; > > > + bias-pull-down; > > > + }; > > > + }; > > > + > > > + sd_pins: sd_pins { > > > + pinmux { > > > + function = "sdio"; > > > + pins = "gpio23", "gpio24", "gpio25", "gpio26", > > > + "gpio28", "gpio29", "gpio30", "gpio31"; > > > + drive-strength = <10>; > > > + }; > > > + > > > + pinmux_sd_clk { > > > + function = "sdio"; > > > + pins = "gpio27"; > > > + drive-strength = <16>; > > > + }; > > > + > > > + pinmux_sd7 { > > > + function = "sdio"; > > > + pins = "gpio32"; > > > + drive-strength = <10>; > > > + bias-disable; > > > + }; > > > + }; > > > +}; > > > + > > > +&watchdog { > > > + status = "okay"; > > > +}; > > > + > > > +&prng { > > > + status = "okay"; > > > +}; > > > + > > > +&blsp_dma { > > > + status = "okay"; > > > +}; > > > + > > > +&blsp1_spi1 { > > > + status = "okay"; > > > + > > > + pinctrl-0 = <&spi_0_pins>; > > > + pinctrl-names = "default"; > > > + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; > > > + > > > + flash@0 { > > > + compatible = "jedec,spi-nor"; > > > + spi-max-frequency = <24000000>; > > > + reg = <0>; > > > + > > > + partitions { > > > + compatible = "fixed-partitions"; > > > + #address-cells = <1>; > > > + #size-cells = <1>; > > > + > > > + partition@0 { > > > + label = "SBL1"; > > > + reg = <0x00000000 0x00040000>; > > > + read-only; > > > + }; > > > + partition@40000 { > > > + label = "MIBIB"; > > > + reg = <0x00040000 0x00020000>; > > > + read-only; > > > + }; > > > + partition@60000 { > > > + label = "QSEE"; > > > + reg = <0x00060000 0x00060000>; > > > + read-only; > > > + }; > > > + partition@c0000 { > > > + label = "CDT"; > > > + reg = <0x000c0000 0x00010000>; > > > + read-only; > > > + }; > > > + partition@d0000 { > > > + label = "DDRPARAMS"; > > > + reg = <0x000d0000 0x00010000>; > > > + read-only; > > > + }; > > > + partition@e0000 { > > > + label = "APPSBLENV"; /* uboot env */ > > > + reg = <0x000e0000 0x00010000>; > > > + read-only; > > > + }; > > > + partition@f0000 { > > > + label = "APPSBL"; /* uboot */ > > > + reg = <0x000f0000 0x00080000>; > > > + read-only; > > > + }; > > > + partition@170000 { > > > + label = "ART"; > > > + reg = <0x00170000 0x00010000>; > > > + read-only; > > > + }; > > > + partition@180000 { > > > + label = "cfg"; > > > + reg = <0x00180000 0x00040000>; > > > + }; > > > + partition@1c0000 { > > > + label = "firmware"; > > > + compatible = "denx,fit"; > > > + reg = <0x001c0000 0x01e40000>; > > > + }; > > > + }; > > > + }; > > > +}; > > > + > > > +/* Some DVK boards ship without NAND */ > > > +&nand { > > > + status = "okay"; > > > + > > > + pinctrl-0 = <&nand_pins>; > > > + pinctrl-names = "default"; > > > +}; > > > + > > > +&blsp1_uart1 { > > > + status = "okay"; > > > + > > > + pinctrl-0 = <&serial_pins>; > > > + pinctrl-names = "default"; > > > +}; > > > + > > > +&cryptobam { > > > + status = "okay"; > > > +}; > > > + > > > +&crypto { > > > + status = "okay"; > > > +}; > > > + > > > +&mdio { > > > + status = "okay"; > > > + > > > + pinctrl-0 = <&mdio_pins>; > > > + pinctrl-names = "default"; > > > +}; > > > + > > > +&pcie0 { > > > + status = "okay"; > > > + > > > + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; > > > + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; > > > + > > > + /* Free slot for use */ > > > + bridge@0,0 { > > > + reg = <0x00000000 0 0 0 0>; > > > + #address-cells = <3>; > > > + #size-cells = <2>; > > > + ranges; > > > + }; > > > +}; > > > + > > > +&wifi0 { > > > + status = "okay"; > > > + > > > + qcom,ath10k-calibration-variant = "8devices-Habanero"; > > > +}; > > > + > > > +&wifi1 { > > > + status = "okay"; > > > + > > > + qcom,ath10k-calibration-variant = "8devices-Habanero"; > > > +}; > > > + > > > +&usb3_ss_phy { > > > + status = "okay"; > > > +}; > > > + > > > +&usb3_hs_phy { > > > + status = "okay"; > > > +}; > > > + > > > +&usb3 { > > > + status = "okay"; > > > +}; > > > + > > > +&usb2_hs_phy { > > > + status = "okay"; > > > +}; > > > + > > > +&usb2 { > > > + status = "okay"; > > > +}; > > > -- > > > 2.26.2 > > > > > > > Hi, > > Is there an issue with the patch preventing the review? > > > > Found this in my inbox and I don't know why I never replied to you, > perhaps because kernel test robot says it doesn't build... > > I tried to apply it now but there's no "vqmmc" so it doesn't build :/ > > > If you're still interested in this I'd be happy to merge it if you can > fix up the vqmmc - and if respinning it I would appreciate if you could > sort the nodes alphabetically. > > Regards, > Bjorn Hi, This patch series depends on: https://patchwork.kernel.org/patch/11765789/ https://patchwork.kernel.org/patch/11760437/ USB nodes appear to finally be picked for the Qcom tree while the VQMMC LDO is still pending. I am still interested in this and was planning to send the updated versions anyway soon. I Will respin these and reorder the nodes. Regards, Robert
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 246d82fc5fcd..004262e0d699 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -898,6 +898,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-ipq4019-ap.dk04.1-c3.dtb \ qcom-ipq4019-ap.dk07.1-c1.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \ + qcom-ipq4019-habanero-dvk.dtb \ qcom-ipq8064-ap148.dtb \ qcom-ipq8064-rb3011.dtb \ qcom-msm8660-surf.dtb \ diff --git a/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts b/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts new file mode 100644 index 000000000000..fe054adda0a7 --- /dev/null +++ b/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts @@ -0,0 +1,304 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* Copyright (c) 2019, Robert Marko <robimarko@gmail.com> */ + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "8devices Habanero DVK"; + compatible = "8dev,habanero-dvk"; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 8 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status: status { + label = "habanero-dvk:green:status"; + gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>; + panic-indicator; + }; + + led_upgrade: upgrade { + label = "habanero-dvk:green:upgrade"; + gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>; + }; + + wlan2g { + label = "habanero-dvk:green:wlan2g"; + gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + label = "habanero-dvk:green:wlan5g"; + gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy1tpt"; + }; + }; +}; + +&vqmmc { + status = "okay"; +}; + +&sdhci { + status = "okay"; + + pinctrl-0 = <&sd_pins>; + pinctrl-names = "default"; + cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; + vqmmc-supply = <&vqmmc>; +}; + +&qpic_bam { + status = "okay"; +}; + +&tlmm { + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-pull-up; + }; + + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + nand_pins: nand_pins { + pullups { + pins = "gpio52", "gpio53", "gpio58", "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + pulldowns { + pins = "gpio54", "gpio55", "gpio56", "gpio57", + "gpio60", "gpio62", "gpio63", "gpio64", + "gpio65", "gpio66", "gpio67", "gpio68", + "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; + + sd_pins: sd_pins { + pinmux { + function = "sdio"; + pins = "gpio23", "gpio24", "gpio25", "gpio26", + "gpio28", "gpio29", "gpio30", "gpio31"; + drive-strength = <10>; + }; + + pinmux_sd_clk { + function = "sdio"; + pins = "gpio27"; + drive-strength = <16>; + }; + + pinmux_sd7 { + function = "sdio"; + pins = "gpio32"; + drive-strength = <10>; + bias-disable; + }; + }; +}; + +&watchdog { + status = "okay"; +}; + +&prng { + status = "okay"; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + status = "okay"; + + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <24000000>; + reg = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + partition@40000 { + label = "MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + partition@60000 { + label = "QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + partition@c0000 { + label = "CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + partition@d0000 { + label = "DDRPARAMS"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + partition@e0000 { + label = "APPSBLENV"; /* uboot env */ + reg = <0x000e0000 0x00010000>; + read-only; + }; + partition@f0000 { + label = "APPSBL"; /* uboot */ + reg = <0x000f0000 0x00080000>; + read-only; + }; + partition@170000 { + label = "ART"; + reg = <0x00170000 0x00010000>; + read-only; + }; + partition@180000 { + label = "cfg"; + reg = <0x00180000 0x00040000>; + }; + partition@1c0000 { + label = "firmware"; + compatible = "denx,fit"; + reg = <0x001c0000 0x01e40000>; + }; + }; + }; +}; + +/* Some DVK boards ship without NAND */ +&nand { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; +}; + +&blsp1_uart1 { + status = "okay"; + + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; +}; + +&cryptobam { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&mdio { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; +}; + +&pcie0 { + status = "okay"; + + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; + + /* Free slot for use */ + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + }; +}; + +&wifi0 { + status = "okay"; + + qcom,ath10k-calibration-variant = "8devices-Habanero"; +}; + +&wifi1 { + status = "okay"; + + qcom,ath10k-calibration-variant = "8devices-Habanero"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3 { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb2 { + status = "okay"; +};
8devices Habanero DVK is a dual-band SoM development kit based on Qualcomm IPQ4019 + QCA8075 platform. Specs are: CPU: QCA IPQ4019 RAM: DDR3L 512MB Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without) WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2 WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2 Ethernet: 5x Gbit LAN (QCA 8075) USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019) MicroSD slot (Uses SD controller built into IPQ4019) SDIO3.0/EMMC slot (Uses the same SD controller) Mini PCI-E Gen 2.0 slot (Built into IPQ4019) 5x LEDs (4 GPIO controllable) 2x Pushbutton (1 is connected to GPIO, other to SoC reset) LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support) 1x UART 115200 rate on J18 2x breakout development headers 12V DC Jack for power DIP switch for bootstrap configuration Signed-off-by: Robert Marko <robert.marko@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr> --- Changes since v1: * Drop include that does not exist arch/arm/boot/dts/Makefile | 1 + .../boot/dts/qcom-ipq4019-habanero-dvk.dts | 304 ++++++++++++++++++ 2 files changed, 305 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts