[1/2] Bluetooth: btbcm: Rewrite bindings i YAML and add reset

This rewrites the Broadcom bluetooth bindings in YAML and
adds a GPIO handle for the BT_RST_N line as used on some
platforms.

Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 .../bindings/net/broadcom-bluetooth.txt       |  56 ---------
 .../bindings/net/broadcom-bluetooth.yaml      | 117 ++++++++++++++++++
 2 files changed, 117 insertions(+), 56 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
 create mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml

On Tue, Nov 03, 2020 at 01:09:42PM +0100, Linus Walleij wrote:
> This rewrites the Broadcom bluetooth bindings in YAML and
> adds a GPIO handle for the BT_RST_N line as used on some
> platforms.

Typo in subject.

> 
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
>  .../bindings/net/broadcom-bluetooth.txt       |  56 ---------
>  .../bindings/net/broadcom-bluetooth.yaml      | 117 ++++++++++++++++++
>  2 files changed, 117 insertions(+), 56 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
>  create mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
> 
> diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
> deleted file mode 100644
> index a7d57ba5f2ac..000000000000
> --- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
> +++ /dev/null
> @@ -1,56 +0,0 @@
> -Broadcom Bluetooth Chips
> ----------------------
> -
> -This documents the binding structure and common properties for serial
> -attached Broadcom devices.
> -
> -Serial attached Broadcom devices shall be a child node of the host UART
> -device the slave device is attached to.
> -
> -Required properties:
> -
> - - compatible: should contain one of the following:
> -   * "brcm,bcm20702a1"
> -   * "brcm,bcm4329-bt"
> -   * "brcm,bcm4330-bt"
> -   * "brcm,bcm43438-bt"
> -   * "brcm,bcm4345c5"
> -   * "brcm,bcm43540-bt"
> -   * "brcm,bcm4335a0"
> -
> -Optional properties:
> -
> - - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml
> - - shutdown-gpios: GPIO specifier, used to enable the BT module
> - - device-wakeup-gpios: GPIO specifier, used to wakeup the controller
> - - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor.
> -                      deprecated, replaced by interrupts and
> -                      "host-wakeup" interrupt-names
> - - clocks: 1 or 2 clocks as defined in clock-names below, in that order
> - - clock-names: names for clock inputs, matching the clocks given
> -   - "extclk": deprecated, replaced by "txco"
> -   - "txco": external reference clock (not a standalone crystal)
> -   - "lpo": external low power 32.768 kHz clock
> - - vbat-supply: phandle to regulator supply for VBAT
> - - vddio-supply: phandle to regulator supply for VDDIO
> - - brcm,bt-pcm-int-params: configure PCM parameters via a 5-byte array
> -    - sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S
> -    - pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps
> -    - pcm-frame-type: short, long
> -    - pcm-sync-mode: slave, master
> -    - pcm-clock-mode: slave, master
> - - interrupts: must be one, used to wakeup the host processor
> - - interrupt-names: must be "host-wakeup"
> -
> -Example:
> -
> -&uart2 {
> -       pinctrl-names = "default";
> -       pinctrl-0 = <&uart2_pins>;
> -
> -       bluetooth {
> -               compatible = "brcm,bcm43438-bt";
> -               max-speed = <921600>;
> -               brcm,bt-pcm-int-params = [01 02 00 01 01];
> -       };
> -};
> diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
> new file mode 100644
> index 000000000000..bdd6ca617e23
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
> @@ -0,0 +1,117 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/broadcom-bluetooth.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Broadcom Bluetooth Chips
> +
> +maintainers:
> +  - Linus Walleij <linus.walleij@linaro.org>
> +
> +description:
> +  This binding describes Broadcom UART-attached bluetooth chips.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - brcm,bcm20702a1
> +      - brcm,bcm4329-bt
> +      - brcm,bcm4330-bt
> +      - brcm,bcm43438-bt
> +      - brcm,bcm4345c5
> +      - brcm,bcm43540-bt
> +      - brcm,bcm4335a0
> +
> +  shutdown-gpios:
> +    maxItems: 1
> +    description: GPIO specifier for the line BT_REG_ON used to
> +      power on the BT module
> +
> +  reset-gpios:
> +    maxItems: 1
> +    description: GPIO specifier for the line BT_RST_N used to
> +      reset the BT module. This should be marked as
> +      GPIO_ACTIVE_LOW.
> +
> +  device-wakeup-gpios:
> +    maxItems: 1
> +    description: GPIO specifier for the line BT_WAKE used to
> +      wakeup the controller. This is using the BT_GPIO_0
> +      pin on the chip when in use.
> +
> +  host-wakeup-gpios:
> +    maxItems: 1
> +    deprecated: true
> +    description: GPIO specifier for the line HOST_WAKE used
> +      to wakeup the host processor. This is using he BT_GPIO_1
> +      pin on the chip when in use. This is deprecated and replaced
> +      by interrupts and "host-wakeup" interrupt-names
> +
> +  clocks:
> +    maxItems: 2
> +    description: 1 or 2 clocks as defined in clock-names below,
> +      in that order
> +
> +  clock-names:
> +    description: Names of the 1 to 2 supplied clocks
> +    items:
> +      - const: txco
> +      - const: lpo
> +      - const: extclk
> +
> +  vbat-supply:
> +    description: phandle to regulator supply for VBAT
> +
> +  vddio-supply:
> +    description: phandle to regulator supply for VDDIO
> +
> +  brcm,bt-pcm-int-params:
> +    $ref: /schemas/types.yaml#/definitions/uint8-array
> +    minItems: 5
> +    maxItems: 5
> +    description: |-
> +      configure PCM parameters via a 5-byte array:
> +       sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S
> +       pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps
> +       pcm-frame-type: short, long
> +       pcm-sync-mode: slave, master
> +       pcm-clock-mode: slave, master
> +
> +  interrupts:
> +    items:
> +      - description: Handle to the line HOST_WAKE used to wake
> +          up the host processor. This uses the BT_GPIO_1 pin on
> +          the chip when in use.
> +
> +  interrupt-names:
> +    items:
> +      - const: host-wakeup
> +
> +  max-speed: true
> +  current-speed: true
> +
> +required:
> +  - compatible
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    uart {
> +        uart-has-rtscts;
> +
> +        bluetooth {
> +            compatible = "brcm,bcm4330-bt";
> +            max-speed = <921600>;
> +            brcm,bt-pcm-int-params = [01 02 00 01 01];
> +            shutdown-gpios = <&gpio 30 GPIO_ACTIVE_HIGH>;
> +            device-wakeup-gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
> +            reset-gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
> +            interrupt-parent = <&gpio>;
> +            interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
> +        };
> +    };
> -- 
> 2.26.2
>